Results for “Electric Aircraft Propulsion” — Page 19

NASA NTRSDate not supplied

Aero-Propulsive Modeling for eVTOL Aircraft Using Wind Tunnel Testing with Multisine Inputs

A novel approach for modeling the aero-propulsive characteristics of an electric vertical takeoff and landing (eVTOL) aircraft was developed and demonstrated in wind tunnel testing. The approach was applied to the NASA LA-8 tandem tilt-wing eVTOL aircraft, using an efficient, hybrid experiment design composed of a static I-optimal response surface design for slowly-varying test variables, and dynamic orthogonal phase-optimized multisine excitations for the control surfaces and electric propulsors. Both the static and dynamic experiment designs were executed simultaneously to collect informative data for model identification. Statistically-weighted multivariate orthogonal function modeling was used to combine local modeling results computed in the frequency domain using data collected with dynamic excitations operating on the control effectors to form an aggregate aero-propulsive model. The final identified model exhibited good predictive capability when compared to validation data acquired separately from the data used to develop the model. The required test time using these new techniques was reduced by at least a factor of five compared to previous static wind tunnel testing for the LA-8 aircraft, while providing more informative data, greater parameterization flexibility, and high-quality models.

system identification↗

NASA NTRS2021

Parametric Study of State-of-Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRS2021

Parametric Study of State of Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRSDate not supplied

Comparison and Application of Battery Modeling Methods for Conceptual Electric Aircraft

Growing interest in design and optimization of electrified aircraft propulsion concepts prompts the need for accurate, flexible, and efficient methods to model battery systems. Presented in this paper are three battery modeling methods that have been used at NASA’s Glenn Research Center, each representing different mathematical or electrical approaches. Thévenin equivalent circuit, normalization, and curve-fitting methods are compared against battery cell test data for the X-57 Maxwell electric aircraft technology demonstrator. The methods are then applied in a simple multidisciplinary optimization context using NASA’s Six-Passenger Electric Quadrotor concept to determine their applicability and performance. The normalization method achieves the highest accuracy for steady and unsteady discharge rates with a voltage mean error percentage of 0.423% and 1.186%, respectively. Optimal quadrotor mission range between the models varies up to 0.5 nmi, identifying current battery modeling methods as a potentially significant contributor to mission analysis error. A set of relevant tools and techniques for conceptual battery modeling are identified in this paper, with conclusions made on the utility of each modeling approach for various design challenges.

power↗

DOE OSTI2023

Environmental Protection Coating System for Refractory Metal Alloys (EPCS for RMAs)

As part of ARPA-E’s Ultra High Temperature Impervious Materials Advancing Turbine Efficiency (UITIMATE) program, this project aims to develop an environmental protection coating system (EPCS) for refractory metal alloys (RMAs) – which will provide radical improvement in long term protection for ultra-high temperature refractory metal components in harsh gas-turbine environments. The drive for higher fuel efficiency and higher core power of gas turbines used in electric power generation and in aircraft propulsion requires higher peak operation temperatures. The temperature capability of state-of-the-art materials cannot meet the new requirements. Refractory metal alloys have desirable capabilities for achieving the required peak temperatures, but most of them are subject to oxidation in the gas turbine environment. Thus, there is a strong need to develop novel environmental protective coatings that enable the refractory metals to operate in an ultra-high temperature engine environment. This project is composed of four major technical innovations that can provide a potentially transformational solution in providing environmental protection for refractory metal alloys over a wide range of temperature. 1) Multi-layer self-healing environmental barrier coating (EBC) that provides protection against combustion gas environment. 2) Oxidation resistant diffusion barrier (DB) on the alloy surface to enhance coating stability. 3) Synergistic integration of the multi-layer self-healing EBC with the diffusion barrier to extend coating life. 4) Guidance of physics-based modeling to accelerate coating development and optimization. Our team has successfully developed a multi-layer self-healing environmental protection coating system (EPCS) that can provide oxidation protection for commercially available molybdenum based refractory metal alloys over a wide temperature range of up to 1600 °C for fuel-efficient gas turbine applications. The team also developed a multi-layer high temperature coating design tool to accelerate coating development and optimization based on physics-based modeling. The team also engaged RTX business unite, notable Pratt and Whitney, for future commercialization of this technology. The successful completion of this Phase I effort led to the selection of performing Phase II of the program. In Phase II, the team plans to apply the EPCS in the protection of a newly discovered molybdenum-based metal alloy which has the potential of superior high temperature properties to the commercial products. Th coating will be evaluated under test conditions and environment that mimic gas turbine operation.

36 MATERIALS SCIENCE↗

NASA NTRS2018

Turbo-Generation Control

Electrified Aircraft Propulsion (EAP) power systems are being studied at the NASA Electric Aircraft Testbed (NEAT) facility. The electric motors at NEAT have the capability to dynamically respond to commands that would be unrealistic when integrated with turbomachinery. There is a need to provide more realistic turbine transients for future system performance studies.

Hybrid Electric↗

NASA NTRSDate not supplied

Hybrid Electric Turboprop Commercial Freighter (HETCOF) Market Study

The dedicated air cargo and freight market has the potential to be a critical early pathway for emerging technologies in low to zero emission propulsion. This study analyzes the cargo aviation market to understand current market trends and future market viability of a mid-sized all-electric or hybrid-electric concept aircraft. While cargo aviation’s overall emissions footprint is small relative to commercial passenger aviation, it remains an important and challenging transportation sector to decarbonize. Past research has focused on small, less than 19-seat electrified aircraft propulsion concepts that could serve both passenger and air cargo markets. This study extends the electrified market space into larger aircraft classes, considering if a purpose-built large hybrid electric turboprop freighter can compete in the market currently served primarily by conversion narrowbody freighters. Specifically, this paper focuses on the mid-sized cargo market with payload ranges of 40,000-50,000lbs, and an all-electric range potential up to 750 miles. The concept aircraft is based on a 4-engine turboprop configuration, with wing mounted battery packs and an aft cargo door to allow for standardized palletization. The market analysis indicates broad market coverage with 73% of the existing mid-sized cargo network within the range of 750 miles. A breakeven analysis of operating and capital costs shows potential for market competition; however, this would require additional energy and acquisition cost savings from the concept aircraft. Evidence from the breakeven analysis also points to higher rates of aircraft utilization being a critical path to lowering costs and increasing cost effectiveness.

Hybrid Electric↗

NASA NTRSDate not supplied

Development of the X-57 Mod III/IV Piloted Simulator and Discussion of the Resultant Flighting Qualities Predictions

The all-electric X-57 Mod III aircraft was designed to demonstrate wingtip propulsion drag reduction benefits on a high-aspect-ratio wing. The X-57 Mod IV aircraft was designed to expand on the Mod III version and demonstrate the benefits of distributed electric propulsion. This paper discusses the development of theall-electricX-57 Mod III and Mod IV fixed-base pilot-in-the-loop nonlinear simulator. The paper describes the model development and the simulator cockpit construction for uses such as flight training and flying qualities analysis. Results from a stability and flying qualities analysis for both Mod III and Mod IV are presented. These results predict that both Mod III and Mod IV are stable throughout their flight envelopes. Mod III is predicted to have satisfactory flying qualities while Mod IV is predicted to have areas of adequate flying qualities.

Ryan Wallace↗

NASA NTRS2005

Switched-Reluctance Cryogenic Motor Tested and Upgraded

Pollution-free flight is one of NASA s goals for the 21st century. One method of approaching that goal is to use hydrogen-fueled aircraft that use fuel cells or turbogenerators to produce electric power to drive electric motors that turn the aircraft s propulsive fans or propellers. Hydrogen fuel would likely be carried as a liquid, stored in tanks at hydrogen s boiling point of 20.5 K (-422.5 F). The liquid hydrogen could provide essentially free refrigeration to cool electric motor windings before being used as fuel. Either superconductivity or the low resistance of pure copper or aluminum in liquid hydrogen could be applied to greatly increase electric current density and motor power density.

Brown, Gerald V.↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRS2024

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Design and Fabrication of the Langley Aerodrome No. 8 - Distributed Electric Propulsion VTOL Testbed

The Langley Aerodrome No. 8 (LA-8) is a distributed electric propulsion, vertical takeoff and landing (VTOL) aircraft that is being used for wind tunnel testing and free flight testing at the NASA Langley Research Center. The intent of the LA-8 project is to provide a low-cost, modular test bed for technologies in the area of Advanced Air Mobility which includes electric urban and short regional flight. The methods used on the LA-8 provide a rapid means to verify aerodynamic, acoustic, and flight dynamics analysis of new electric VTOL and short takeoff and landing (STOL) designs. In addition, the flight vehicle will be used to help develop test processes for FAA flight vehicle airworthiness certification and for the development of robust flight control algorithms that are tolerant of failures. A new approach is being used on test vehicle design that makes extensive use of 3-D printing. Although materials used in 3-D printing have less strength than traditional materials used for NASA’s wind tunnel and flight models, strategic placement of load-carrying structures allows the aircraft to meet structural criteria while also enabling easy changes to be made in the vehicle design, such as the outer mold line. Modularity of the vehicle’s main components allows rapid changes to the vehicle configuration for comparative evaluation of alternate designs. Finally, a description is given of detailed inertia measurements of the flight vehicle using compound pendulum swing methods.

Urban air mobility↗

NASA NTRSDate not supplied

Some NASA Perspectives on H2

This presentation provides the NASA perspective for government and industry technology developers world-wide who are exploring the potential for hydrogen (H2) in aviation applications including electric aircraft, airport vehicles, and airport related equipment. NASA’s H2 interest has been related to vehicle-level technology development and integration only, but NASA is keenly aware of the necessity of work focused on solving the challenges of H2 airport infrastructure. Some historical perspectives are provided on NASA efforts in H2 fuel cell development for space and aeronautics applications. NASA’s current research portfolio includes some investigation of H2 energy storage and hydrocarbon conversion for fuel cells on electric aircraft. There is no current emphasis on the other H2-related challenges. Over the years NASA has conducted research into “Quiet Green Transport” with a H2 fuel cell powered aircraft, an Emissionless Aircraft Study with Non Flow Through – Regenerative Fuel Cell (NFT-RFC) technology which captures the water, and an H2 fuel cell powered Unmanned Aerial Vehicle (UAV) study. NASA has flown a long endurance UAV using a RFC in the Low Emissions Alternative Power (LEAP) program. Recently, NASA conducted feasibility studies on hybrid SOFC with onboard hydrocarbon fuel reformation for aircraft primary propulsive power and secondary power under the Fostering Ultra-Efficient, Low-Emitting Aviation Power (FUELEAP) program. NASA currently has a multiyear program with the Center for Cryogenic High-Efficiency Electrical Technologies for Aircraft (CHEETA) to explore the benefits of using cryogenic H2 on aircraft for fuel cell propulsion and to provide superconductivity in electrical power management on the aircraft.

Power↗

NASA NTRS2015

Assessment of Technologies for Noncryogenic Hybrid Electric Propulsion

The Subsonic Fixed Wing Project of NASA's Fundamental Aeronautics Program is researching aircraft propulsion technologies that will lower noise, emissions, and fuel burn. One promising technology is noncryogenic electric propulsion, which could be either hybrid electric propulsion or turboelectric propulsion. Reducing dependence on the turbine engine would certainly reduce emissions. However, the weight of the electricmotor- related components that would have to be added would adversely impact the benefits of the smaller turbine engine. Therefore, research needs to be done to improve component efficiencies and reduce component weights. This study projects technology improvements expected in the next 15 and 30 years, including motor-related technologies, power electronics, and energy-storage-related technologies. Motor efficiency and power density could be increased through the use of better conductors, insulators, magnets, bearings, structural materials, and thermal management. Energy storage could be accomplished through batteries, flywheels, or supercapacitors, all of which expect significant energy density growth over the next few decades. A first-order approximation of the cumulative effect of each technology improvement shows that motor power density could be improved from 3 hp/lb, the state of the art, to 8 hp/lb in 15 years and 16 hp/lb in 30 years.

Electric Propulsion↗

DOE OSTI2023

Nuclear fusion powered Titan aircraft

This paper discusses a system for Titan exploration enabled by nuclear fusion power. Titan is one of the most interesting locations in the solar system with a thick atmosphere, surface oceans, under-ice oceans and complex terrain. This paper provides a conceptual design of a fusion-powered system to explore many parts of Titan and enable the use of high-power instruments. The design includes a fusion-powered orbital transfer vehicle and an electric Titan science aircraft. A Direct Fusion Drive (DFD) propulsive engine could bring a sizable spacecraft to Titan orbit in less than two years. A second fusion reactor, configured as a closed-loop power generator, would be used for an electric Titan science aircraft. Both reactors are based on the Princeton Field-Reversed Configuration (PFRC) concept which combines an FRC with a magnetic mirror. PFRC uses a novel radio-frequency plasma heating system and deuterium-helium-3 fuel. A lower temperature plasma flows around the closed-field FRC region removing the fusion products. In the DFD propulsive configuration, this secondary flow permits direct and variable thrust and exhaust velocity. The science aircraft would do a powered entry to Titan and then have the capability to fly anywhere on the moon at subsonic speeds. The DFD-powered transfer vehicle would allow the in-orbit transfer stage to change inclination as needed to cover different areas of the surface.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRSDate not supplied

Exploration of the Versatile Electrically Augmented Turbine Engine Gearbox Concept

Integration of electric machines with the shafts of gas turbine engines is implied in various electrified aircraft propulsion concepts. This includes implementation of the Turbine Electrified Energy Management (TEEM) concept, a motivator for the Versatile Electrically Augmented Turbine Engine (VEATE) gearbox. The VEATE gearbox is a mechanical power transmission concept that seeks to interface electric machines with a gas turbine engine in a synergistic manner. It enables a hybrid electro-mechanical approach for managing power in a gas turbine engine. It is hypothesized that the mechanical design of the VEATE gearbox could be leveraged to enhance the versatility of the present electrical hardware. The VEATE gearbox concept is first introduced and applied to an electrified two-spool advanced geared turbofan meant for powering a single-aisle commercial aircraft. A modeling approach for the gearbox is presented and studies are conducted to investigate the potential application to TEEM and power extraction. There is evidence that the VEATE gearbox could help to reduce the size of the TEEM power system, provide flexibility in power extraction implementation, and exhibit fail-safe design attributes.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Brief Overview of Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

The SUSAN concept uses a 20-megawatt Electrified Aircraft Propulsion system to enable advance Propulsion Airframe Integration in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50 percent per passenger/mile while retaining the size, speed, and range of large regional jets. The SUSAN is has a 750-mile economic mission, a 2500-mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace, and economic constraints. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph Jansen↗