Results for “Electrified Propulsion” — Page 19

NASA NTRS2018

Magnetic Gearing Research at NASA

Magnetic gearing is an alternative to mechanical gearing, where torque is transferred through magnetic force as opposed to contact force. The technology has the potential to be used in aircraft applications, without the lubrication, noise, and maintenance issues that can exist with mechanical gearing. Initial design and prototype development work was done at NASA to create a foundational understanding of the technology and the factors that influence its specific torque. The specific torque achieved through design optimization was found to be less than that of high-torque mechanical aircraft transmissions, but may be comparable to that of lower torque mechanical transmissions for electrified vertical takeoff and landing aircraft. The lessons learned from NASA's initial technology development and the direction of NASA's future work in field are discussed.

electric aircraft propulsion↗

NASA NTRS2018

X-57 Maxwell Battery from Cell Level to System Level Design and Testing

The X-57 Maxwell flight demonstrator aircraft is an experimental aircraft designed to demonstrate radically improved aircraft efficiency with a 3.5 times aero-propulsive efficiency gain at a "high-speed cruise" flight condition for comparable general aviation aircraft. These gains are enabled by integrating the design of a new, optimized wing and a new electric propulsion system. There are 14 propulsors in all: 12 high lift motor that are only active during takeoff and climb, and 2 larger motors positioned on the wingtips that operate over the entire mission. The innovative electric propulsion system will have as its primary power a Li-ion battery system. Integrating a battery system into this innovative design poses unique challenges that require careful design considerations across the system. The presentation will cover a breakout of X-57 battery specifications, battery design and lessons learned when designing a high voltage battery system to power electrified aircrafts.

Hernandez Lugo, Dionne↗

NASA NTRSDate not supplied

Analysis and Optimization of Baseline Single Aisle Aircraft for Future Electrified Powertrain Flight Demonstrator Comparisons

The purpose of this study is to provide baseline single-aisle vehicles for future comparisons NASA’s Electrified Powertrain Flight Demonstrator (EPFD) turbofan powered Vision Systems. Both a large single-aisle (≈150 passenger) and a small single-aisle (≈100 passenger) vehicle will be analyzed using NASA’s General Aviation Synthesis Program and a modernized Python-based version of this program that enables efficient gradient-based optimization of both the airframe and propulsion that currently is being referred to as GASPy. A technology build-up will be conducted to bring the current State-of-the-art vehicles to a projected 2035 technology level by incorporating estimations for improvements in aerodynamics, structures, and propulsions. These vehicles can be used in NASA’s future EPFD project as baselines to measure the benefits of future hybrid and fully electric aircraft against. The advanced, large single-aisle will then be used to demonstrate the benefits of a coupled engine-airframe optimization for fuel burn reduction.

Carl J Recine↗

NASA NTRS2021

Design and Development of Nano-electro Fuel Batteries and Rim-driven Motors for Electrified Aircraft Applications

The National Aeronautics and Space Administration Convergent Aeronautics Solutions project seeks to determine feasibility of emerging technologies in aeronautics. The Aqueous, QUick-Charging Battery Integration For Electric flight Research study pursued the feasibility of nano-electro fuel and rim-driven motor technologies integrated together for aircraft implementation. Development of the NEF technology was in partnership with Influit Energy, LLC (Chicago, Illinois). A rim-driven motor, designed by the project team, sized to represent one of 24 motors in the propulsion system of the tandem electric super-short takeoff and landing aircraft is discussed. The development of this electric super-short takeoff and landing concept was in partnership with The Boeing Company (Chicago, Illinois). The integrated system design of the nano-electro fuel and rim-driven motor technologies within the wing section was in partnership with Empirical Systems Aerospace, Inc. (ESAero) (San Luis Obispo, California). The feasibility benchmark for the nano-electro fuel battery was to attain 100 mA/sq. cm within two years, a 50-fold increase over the demonstrated cell performance before the Convergent Aeronautics Solutions Aqueous, QUick-Charging Battery Integration For Electric flight Research activity. The team achieved 85 mA/sq. cm in the nano-electro fuel flow cell at the end of the two years. The Aqueous, QUick-Charging Battery Integration For Electric flight Research project team determined the technology to be both inflammable and nonexplosive (unless multiple, simultaneous system failures occur) which would provide a safer alternative to conventional lithium-ion based battery systems.

Kurt V. Papathakis↗

NASA NTRSDate not supplied

Analysis and Optimization of Baseline Single Aisle Aircraft for Future Electrified Powertrain Flight Demonstrator Comparisons

The purpose of this study is to provide baseline single-aisle vehicles for future comparisons with NASA’s Electrified Powertrain Flight Demonstration (EPFD) turbofan-powered Vision Systems. State-of-the-art single-aisle transports with varying design capacities of 100 to 150 passengers are modeled using NASA Ames Research Center’s General Aviation Synthesis Program (GASP) as well as GASPy. GASPy is a modernized Python-based version of GASP built on the OpenMDAO framework to allow for future, efficient gradient-based optimization and coupled airframe-propulsion design. In order to meet projected NASA Aeronautics goals for 2035, advanced aircraft technologies must be incorporated into these vehicle systems. Methodology to parametrically infuse baseline aircraft models with advanced technologies simulating improvements in aerodynamics, structures, and propulsion systems is detailed, along with the results of technology sensitivity studies. Comparison of the baseline and advanced configurations will allow for future analysis of the benefits of future hybrid and fully electric aircraft concepts in the EPFD project, where fuel consumption and emissions will be modeled and assessed. This study has been conducted under the EPFD project to establish benchmark turbofan models and demonstrate System Analysis capabilities in multi-disciplinary aircraft design, analysis, and optimization for advanced turbofan concepts.

Carl J. Recine↗

NASA NTRSDate not supplied

Transient Optimization of an Electrified Gas Turbine Engine Using Machine Learning

Gas turbine engines are designed with sufficient margin to prevent stall under normal operating conditions throughout their life. This compromise ensures that during rapid accelerations, compressor operation remains stable, but at the cost of efficiency and thrust responsiveness. The design margin encompasses multiple sources of uncertainty and systematic deviances from the operating line, the largest of which is the transient allowance. This set-aside accounts for the temporary incoordination of the engine spools during an acceleration while still enabling it to meet the certification requirement to accelerate from low to high power within a specified time, and without experiencing overtemperature, surge, stall, or other detrimental factors. Electrification of the powertrain provides the opportunity to address this reserve and truly optimize the design. The addition of electric machines inherent in hybrid propulsion concepts offers a means to interact with the engine shafts such that the necessary margin can be reduced, which can positively impact the engine design. By adjusting the amount of power extracted from or injected to the engine spools by the electric machines during transient operation, excursions from the operating line can be minimized. Past work using a dynamic engine model has shown that optimization of the fuel flow schedule during acceleration can reduce the required margin while still meeting the time requirement, and results are further improved when combined with power injection and extraction. The current work uses machine learning through a genetic algorithm to address the problem holistically by concurrently optimizing the electric machine power command and fuel flow acceleration schedule using an updated, higher fidelity version of the original engine model.

Stall Margin↗

NASA NTRSDate not supplied

Transient Optimization of an Electrified Gas Turbine Engine Using Machine Learning

Gas turbine engines are designed with sufficient margin to prevent stall under normal operating conditions throughout their life. This compromise ensures that during rapid accelerations, compressor operation remains stable, but at the cost of efficiency and thrust responsiveness. The design margin encompasses multiple sources of uncertainty and systematic deviances from the operating line, the largest of which is the transient allowance. This set-aside accounts for the temporary incoordination of the engine spools during an acceleration while still enabling it to meet the certification requirement to accelerate from low to high power within a specified time, and without experiencing overtemperature, surge, stall, or other detrimental factors. Electrification of the powertrain provides the opportunity to address this reserve and truly optimize the design. The addition of electric machines inherent in hybrid propulsion concepts offers a means to interact with the engine shafts such that the necessary margin can be reduced, which can positively impact the engine design. By adjusting the amount of power extracted from or injected to the engine spools by the electric machines during transient operation, excursions from the operating line can be minimized. Past work using a dynamic engine model has shown that optimization of the fuel flow schedule during acceleration can reduce the required margin while still meeting the time requirement, and results are further improved when combined with power injection and extraction. The current work uses machine learning through a genetic algorithm to address the problem holistically by concurrently optimizing the electric machine power command and fuel flow acceleration schedule using an updated, higher fidelity version of the original engine model.

Stall Margin↗

NASA NTRS2024

Transient Optimization of an Electrified Gas Turbine Engine Using Machine Learning

Gas turbine engines are designed with sufficient margin to prevent stall under normal operating conditions throughout their life. This compromise ensures that during rapid accelerations, compressor operation remains stable, but at the cost of efficiency and thrust responsiveness. The design margin encompasses multiple sources of uncertainty and systematic deviances from the operating line, the largest of which is the transient allowance. This set-aside accounts for the temporary incoordination of the engine spools during an acceleration while still enabling it to meet the certification requirement to accelerate from low to high power within a specified time, and without experiencing overtemperature, surge, stall, or other detrimental factors. Electrification of the powertrain provides the opportunity to address this reserve and truly optimize the design. The addition of electric machines inherent in hybrid propulsion concepts offers a means to interact with the engine shafts such that the necessary margin can be reduced, which can positively impact the engine design. By adjusting the amount of power extracted from or injected to the engine spools by the electric machines during transient operation, excursions from the operating line can be minimized. Past work using a dynamic engine model has shown that optimization of the fuel flow schedule during acceleration can reduce the required margin while still meeting the time requirement, and results are further improved when combined with power injection and extraction. The current work uses machine learning through a genetic algorithm to address the problem holistically by concurrently optimizing the electric machine power command and fuel flow acceleration schedule using an updated, higher fidelity version of the original engine model.

Stall Margin↗

NASA NTRS2017

Dynamic Modeling, Controls, and Testing for Electrified Aircraft

Electrified aircraft have the potential to provide significant benefits for efficiency and emissions reductions. To assess these potential benefits, modeling tools are needed to provide rapid evaluation of diverse concepts and to ensure safe operability and peak performance over the mission. The modeling challenge for these vehicles is the ability to show significant benefits over the current highly refined aircraft systems. The STARC-ABL (single-aisle turbo-electric aircraft with an aft boundary layer propulsor) is a new test proposal that builds upon previous N3-X team hybrid designs. This presentation describes the STARC-ABL concept, the NASA Electric Aircraft Testbed (NEAT) which will allow testing of the STARC-ABL powertrain, and the related modeling and simulation efforts to date. Modeling and simulation includes a turbofan simulation, Numeric Propulsion System Simulation (NPSS), which has been integrated with NEAT; and a power systems and control model for predicting testbed performance and evaluating control schemes. Model predictions provide good comparisons with testbed data for an NPSS-integrated test of the single-string configuration of NEAT.

Connolly, Joseph↗

NASA NTRS2018

Preliminary Design of the Superconducting Rotor for NASA's High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4~MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. The design of the superconducting rotor and the optimization of its electromagnetic and structural responses are analyzed in this paper. Candidate designs are evaluated in terms of absolute performance, specific performance, and performance per cost. It is found that optimizing the electromagnetic response for absolute or specific performance yields designs that are similar to each other, but opposite of the cost-optimized design. A method to define the thermal requirements of the superconducting coils and integrated cryocooler is also presented.

electric machines↗

NASA NTRS2023

Exploring Synoptic Display Concepts for Hybrid-Electric Airliner Flightdecks

The advent of hybrid-electric aircraft concepts with distributed propulsion has resulted in relatively complicated powertrain designs. Determining the optimal approach to display information about the hybrid system in the flightdeck has taken on great importance. At NASA Glenn Research Center, the concept SUbsonic Single Aft eNgine (SUSAN) hybrid airliner has been modeled inside a flight simulator where different flight deck displays can be evaluated. This work focused on ways to display information that reduce clutter and information overload without degrading the crew’s ability to operate the aircraft and respond properly to emergencies. The displays’ layout and symbologies were created to be intuitive to the pilots. This paper documents iterations of synoptic displays and discusses the rationale and tradeoffs behind each variation.

Pilot Displays↗

NASA NTRS2018

Design, Fabrication, and Critical Current Testing of No-Insulation Superconducting Rotor Coils for NASA's 1.4 MW High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4 MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the design and fabrication of the no-insulation high temperature superconducting (HTS) rotor coils and compares them to conventionally insulated HTS coils. Two sub-scale test coils with epoxy on only one axial face were fabricated. Critical current testing of the coils at 77 K and self field was conducted to study the influence of thermal cycling on their critical current and n-value. After two or four aggressive thermal cycles between 77 K and about 278 K (5 degree C), the critical current and n-value were nearly unchanged, indicating very little to no degradation.

electric aircraft propulsion↗

NASA NTRSDate not supplied

Select Variables Affecting Thermal System Design of a Liquid-Cooled Stator

NASA Glenn Researchers have endeavored to create a high-power-density, efficient electric motor called the High Efficiency Megawatt Motor (HEMM) with a goal of exceeding 98% efficiency and 1.46 MW of power. These aggressive goals were set because increasing the power density and efficiency of electric machines (motors and generators) is integral to bringing electrified aircraft (EA) to commercial realization. Resistive losses in the stator windings are by far the largest (34%) contributor to this design’s total energy losses. Previous testing of a HEMM-like stator test article (statorette) showed good agreement between measured performance and model predictions. Therefore, a foundation was provided to test other engineering parameters that are encountered when designing an electric machine. Of particular interest are the effects of changes to the thickness of the epoxy from the potting process, changes in the fluid volume/flow path around the end windings, and changes in the viscosity of the cooling fluid on the overall thermal performance of the unit. The impact of those parameters as revealed through a third-generation build, test, and finite element model analysis of a statorette test section is the focus of this paper.

EAP↗

NASA NTRS2026

AC and DC Fault Management for Megawatt Electrified Aircraft Electrical Powertrains Task 3: Lifetime and Reliability of Electrical Insulators

This research project was a collaborative investigation between researchers at the RTX Technology Research Center (RTRC) and the University of Texas at Austin and made a significant contribution to enabling electric aircraft. The transport of electric power between the points of generation and use requires power cables. These cables must be smaller, lighter and provide a more predictable life than power cables used in stationary applications. Consequently, this investigation provided heretofore unavailable information supporting the safety and reliability of smaller lighter power cables for electrified aircraft. In addition, the research identified key additional engineering data needed to support quantitative reliability assessments. Important advances included: • Demonstrated that at least one manufacturer can make a novel, smaller, lighter power cable that is free from serious defects. • Developed and published an appropriate analytical construct to describe the life of this novel cable. This is a necessary step for use in aviation where the understanding of remaining life is critical. • Demonstrated thermal-mechanical aging that suggested 1000+ flights before the thermal-mechanical processes produced defects large enough that the defect growth was accelerated electrically. • Showed that electrical aging took place at two rates. The first possibly lasting weeks to months and the second possibly days to weeks. If robust, this provides a good diagnostic for cable replacement. • Demonstrated that the traditional electrical testing of cable materials using manufactured voids can be misleading due to the size of the voids. Emerging laser drilling technology permitted demonstration that the physics of failure in realistically small voids is different from that in the unrealistically large voids used in earlier research, which is very important for high-quality, high-performance, small aircraft cables. Although this project represents a significant contribution to the specifics of cable aging in the aircraft environment, important additional research remains to be completed, including: • Non-uniform thermal cycling by applying the heat from the center conductor to maximize thermal stress next to the core area where the electric gradient is the strongest. This builds on the uniform thermal cycling that has been completed. • The augmentation of the thermal-mechanical failure rate by electrical processes. Better understanding of these time constants strongly affects the ability to predict life. • Termination design: Terminations provide not only electrical reflection potential, but a location for a series arc fault and an area where ozone can diffuse into the center conductor and negatively affect cable insulation. • The abrasion and ozone resistance of the cable jacket. • Pressure cycling as an accelerant of thermal, mechanical, and/or electrical aging. • Possible methods for online PD detection and offline PD localization

model↗