Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental Results”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Fracture mechanics analysis of composite microcracking - Experimental results in fatigue

The Nairn (1989) variational mechanics analysis, which yields the energy release rate of a microcrack's formation between two existing microcracks, has proven useful in the fracture mechanics interpretation of cross-ply laminates' microcracking. Attention is presently given to the application of this energy release rate analysis to a fracture mechanics-based interpretation of microcrack formation during fatigue loading, for the case of fatigue experiments on three layups of Avimid K/IM6 laminates and four layups of Fiberite 934/T300 laminates. The single master Paris-law plot onto which the data from all layups of a given material system fall is claimed to offer a complete characterization of that system's microcrack-formation resistance during fatigue loading.

Nairn, J. A.↗
NASA NTRS1991

Experimental results using active control of traveling wave power flow

Active structural control experiments conducted on a 24-ft pinned-free beam derived feedback compensators on the basis of a traveling-wave approach. A compensator is thus obtained which eliminates resonant behavior by absorbing all impinging power. A causal solution is derived for this noncausal compensator which mimics its behavior in a given frequency range, using the Wiener-Hopf. This optimal Wiener-Hopf compensator's structure-damping performance is found to exceed any obtainable by means of rate feedback. Performance limitations encompassed the discovery of frequencies above which the sensor and actuator were no longer dual and an inadvertent coupling of the control hardware to unmodeled structure torsion modes.

Miller, David W.↗
NASA NTRS1991

Plasma discharge in N2 + CH4 at low pressures - Experimental results and applications to Titan

Results are reported from laboratory continuous-flow plasma-discharge experiments designed to simulate the formation of hydrocarbons and nitriles from N2 and CH4 in the atmosphere of Titan. Gas-chromatography and mass-spectrometry data were obtained in experiments lasting up to 100 h at temperature 295 K and pressure 17 or 0.24 mbar, modeling (1) cosmic-ray-induced processes in the Titan troposphere and (2) processes related to stratospheric aurorae excited by energetic electrons and ions from the Saturn magnetosphere, respectively. The results are presented in extensive tables and graphs, and the 0.24-mbar yields are incorporated into an eddy-mixing model to give stratospheric column abundances and mole fractions in good agreement with Voyager IRIS observations.

Thompson, W. Reid↗
NASA NTRS1990

Adaptive structures - Test hardware and experimental results

The facilities and procedures used at JPL to test adaptive structures such as the large deployable reflector (LDR) are described and preliminary results are reported. The applications of adaptive structures in future NASA missions are outlined, and the techniques which are employed to modify damping, stiffness, and isolation characteristics, as well as geometric changes, are listed. The development of adaptive structures is shown to be effective as a result of new actuators and sensors, and examples are listed for categories such as fiber optics, shape-memory materials, piezoelectrics, and electrorheological fluids. Some ground test results are described for laboratory truss structures and truss test beds, which are shown to be efficient and easy to assemble in space. Adaptive structures are shown to be important for precision space structures such as the LDR, and can alleviate ground test requirements.

Wada, Ben K.↗
NASA NTRS1991

Evaluation of panel code predictions with experimental results of inlet performance for a 17-inch ducted prop/fan simulator operating at Mach 0.2

An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip retios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.

Boldman, D. R.↗
NASA NTRS1991

The behavior of delaminations in composite plates - Analytical and experimental results

The behavior of elliptical sublaminates created by delaminations in composite plates was investigated for plates subjected to in-plane compressive, shear, and thermal loads. The axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed which provides the stresses, strains, and displacements of the sublaminate, and the loads applied to the plate at which the sublaminate buckles and at which it grows in size. A series of experiments was conducted on sandwich plates made of Fiberite T300/976 graphite-epoxy laminates bonded to an aluminum honeycomb core. Teflon film in either a circle or an ellipse was embedded in the laminate, simulating the presence of a delamination. Each plate was loaded in compression, and the load-strain history of the sublaminate, the sublaminate buckling load, and the sublaminate growth load were measured. The predictions of the model agreed reasonably well with the data.

Peck, Scott O.↗
NASA NTRS1990

Parallelism in backward-chained expert systems - Experimental results

There are many applications which may be done by an expert system in real time, if the system is capable of real-time response. The LISP and PROLOG-based expert systems have typically been too slow for real-time response. This has led to an effort to use other languages, the development of fast pattern matching techniques and other methods of improving the speed of expert systems. Another approach to developing faster expert systems is to make use of the emerging parallel processing computer technology. A further use for parallelism is to allow reasonable response time for large knowledge bases. The size of knowledge bases may become as large as 20,000 chunks of knowledge (and more) in the near future in medical and space applications. This paper describes the use of parallel processing in the EMYCIN backward chained rule-based model.

Hall, Lawrence O.↗
NASA NTRS1991

Experimental results of a propeller/wing interaction study

Steady state measurements have been performed on a propellar and a wing in a tractor configuration, to investigate the consequences of mutual interference on overall performance. For certain geometries wing lift is found to be enhanced, and wing drag to be decreased. The unsteady nature of the propeller-wing aerodynamic interaction has been studied using flow visualization. Results obtained indicate that the tip vortex is severed at the wing leading edge, the severed tip vortex filaments shear in a spanwise direction relative to one another, and these displaced filaments deform to reconnect at the trailing edge.

Johnson, Robert T.↗
NASA NTRS1991

Analysis, design, and experimental results for lightweight space heat receiver canisters, phase 1

Critical technology experiments have been performed on thermal energy storage modules in support of the Brayton Advanced Heat Receiver program. The modules are wedge-shaped canisters designed to minimize the mechanical stresses that occur during the phase change of the lithium fluoride phase change material. Nickel foam inserts were used in some of the canisters to provide thermal conductivity enhancement and to distribute the void volume. Two canisters, one with a nickel foam insert, and one without, were thermally cycled in various orientations in a fluidized bed furnace. The only measurable impact of the nickel foam was seen when the back and short sides of the canister were insulated to simulate operation in the advanced receiver design. In tests with insulation, the furnace to back side delta T was larger in the canister with the nickel foam insert, probably due to the radiant absorptivity of the nickel. However, the differences in the temperature profiles of the two canisters were small, and in many cases the profiles matched fairly well. Computed Tomography (CT) was successfully used to nondestructively demarcate void locations in the canisters. Finally, canister dimensional stability, which was measured throughout the thermal cycling test program with an inspection fixture was satisfactory with a maximum change of 0.635 mm (0.025 in.).

Schneider, Michael G.↗
NASA NTRS1992

Experimental results and numerical modeling of solidification during aircraft high-g arcs

The question of how the Coriolis and gravity gradient forces during high-gravity maneuvers compare to that for common centrifuges is addressed. Microstructural examination of samples solidified during high-gravity arcs reveals no evidence of convection dampening. As a first approximation, the high-gravity arc is modeled as a centrifuge with a radius of 20,480 ft and angular speed of 0.318 rpm. Scaling analysis indicates that the Coriolis and gravity gradient expected on the aircraft high gravity arc are less than that for the centrifuges by a factor of 100. Detailed Navier-Stokes analysis of the fluid flow and thermal fields during solidification of aluminum and Cd-Te during KC-135 high gravity show that convective flows of about 1 mm/s are induced. The thermal field is only slightly modified by the convection. Coriolis and gravity gradient during solidification in KC-135 high-gravity arcs, even at accelerations that have been shown to produce significant convective flow dampening in the centrifuge systems, are found to have no significant influence on the melt thermal and flowfields.

Curreri, P. A.↗
NASA NTRS1993

Preliminary experimental results for a cryogenic brush seal configuration

Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun porous flow equation was applied to the brush seal data. The Ergun relation, which required heuristic information to characterize the coefficients, fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the (C(sub f)A x Constant) flow and area coefficients. Reasonable agreement between prediction and data was found, as expected, but such methods are not to be construed as two-phase-flow brush seal analyses.

Carlile, J. A.↗
NASA NTRS1992

Delaminations in composite plates under transverse static loads - Experimental results

Tests were performed measuring the damage initiation loads and the locations, shapes, and sizes of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite-PEEK plates subjected to transverse static loads. The data were compared to the results of the Finn-Springer model, and good agreements were found between the measured and calculated delamination lengths and widths.

Finn, Scott R.↗
NASA NTRS1993

Delaminations in composite plates under transverse impact loads - Experimental results

Tests were performed measuring the locations and geometries of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite/PEEK plates subjected to transverse impact loads. The data provide specific information on the effects of impactor velocity, impactor mass, material, thickness of back ply group, difference in fiber orientation between adjacent ply groups, plate thickness, and impactor nose radius. The data were compared to the results of the Finn-Springer model. The model was found to describe the data with reasonable accuracy.

Finn, Scott R.↗
NASA NTRS1993

Preliminary experimental results for a cryogenic brush seal configuration

Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun (1952) porous flow equation was applied to the brush seal data. The Ergun relation fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the flow and area coefficients. Reasonable agreement between prediction and data was found, but such methods are not to be construed as two-phase-flow brush seal analyses.

Carlile, J. A.↗