Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - CHANNELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Comparison between optical measurements and a numerical solution of the flow field within a transonic axial-flow compressor rotor

A comparison between numerical and experimental results is presented for the flowfield within a transonic axial-flow compressor rotor. The rotor was tested at design speed and a wide open throttle discharge condition. The relative tip Mach number was 1.4. A laser anemometer system was used to measure velocity and flow angle upstream, within, and downstream of the rotor. A holographic interferometer was used to visualize the rotor shock system near the tip. The computational procedure solves the full three-dimensional Euler equations using a time-marching technique. Shock location and shape determined from the two optical systems are compared. Calculated relative Mach number and flow angle contours, shock locations, and shock strength are compared to values measured with the laser anemometer.

Strazisar, A. J.↗
NASA NTRS1981

Effects of solid particles suspended in fluid flow through an axial flow compressor stage

An approximate method for calculating the flow properties of gas-particle mixture flowing over blades in a cascade is studied. Using an analytical method, the solid particle trajectory and location of collisions between the solid particles and the blade surfaces are determined. In addition an experimental investigation of the trajectories and velocities of solid particles suspended in a fluid passing through an axial flow compressor cascade was performed. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand with average diameter of 165 microns. The following parameters were investigated: blade pressure distribution, and total pressure loss coefficient, both depending on the degree of erosion. In addition, a theoretical estimation of the blade erosion is compared with the experimental data.

Tabakoff, W.↗
NASA NTRS1982

Aerosound from corner flow and flap flow

Noise generation at the edge of a wing flap is analyzed. The phenomenon as a single vortex moving around a corner in an incompressible, potential flow is modelled. Vortex image retarding effects are proposed as an explanation for small Strouhal numbers. The model surface pressures, sound pressures (using Curle's theory), and Mach number dependencies agree with wind tunnel experiments. A double pressure peak is found in the model (credited to image action) which is qualitatively similar to measured sound correlations. Incompressible flow aerosound calculations are discussed. The effects of a series of vortices moving in the same idealized potential flow are also studied. The vortices are assumed to be statistically independent so their intensities can be added. The frequency of appearance of the vortices are determined from measurements. Diffraction effects caused by the presence of the wing near the dipole sound radiators on the flap surfaces are included.

Meecham, W. C.↗
NASA NTRS1982

Three dimensional flow field inside the passage of a low speed axial flow compressor rotor

Measurements of the subsonic flow in the rotor passage of a single stage axial flow compressor were made to study the nature of the flow field and to verify the existing numerical codes. The velocity and pressure fields were measured across the entire rotor passage at six axial locations and at five radial locations. A five-hole probe, rotating with the rotor, was used to measure the three components of velocity, the static and the total pressure. The experimental results are compared with the predictions from Katsanis and McNally's computer program. The agreement between the two is good for most of the cases.

Pouagare, M.↗
NASA NTRS1982

Evaluation of a wall-flow direction probe for measurements in separated flows

The upstream-downstream flow direction intermittency is an important parameter that can quantitatively describe the stages of flow separation. This paper gives an improved design for a wall-flow-direction probe. Intermittency measurements made using this modified probe show agreement within experimental uncertainties with direct measurements made using a LDV, although both the unmodified and modified probe designs produce results that are consistently higher than those for the LDV.

Shivaprasad, B. G.↗
NASA NTRS1982

Turbulent transport modeling of shear flows around an aerodynamic wing. Development of turbulent near-wall model and its application to recirculating flows

Progress in implementing and refining two near-wall turbulence models in which the near-wall region is divided into either two or three zones is outlined. These models were successfully applied to the computation of recirculating flows. The research was further extended to obtaining experimental results of two different recirculating flow conditions in order to check the validity of the present models. Two different experimental apparatuses were set up: axisymmetric turbulent impinging jets on a flat plate, and turbulent flows in a circular pipe with a abrupt pipe expansion. It is shown that generally better results are obtained by using the present near-wall models, and among the models the three-zone model is superior to the two-zone model.

Amano, R. S.↗
NASA NTRS1982

Solution of 3-dimensional time-dependent viscous flows. Part 3: Application to turbulent and unsteady flows

A numerical scheme is developed for solving the time dependent, three dimensional compressible viscous flow equations to be used as an aid in the design of helicopter rotors. In order to further investigate the numerical procedure, the computer code developed to solve an approximate form of the three dimensional unsteady Navier-Stokes equations employing a linearized block implicit technique in conjunction with a QR operator scheme is tested. Results of calculations are presented for several two dimensional boundary layer flows including steady turbulent and unsteady laminar cases. A comparison of fourth order and second order solutions indicate that increased accuracy can be obtained without any significant increases in cost (run time). The results of the computations also indicate that the computer code can be applied to more complex flows such as those encountered on rotating airfoils. The geometry of a symmetric NACA four digit airfoil is considered and the appropriate geometrical properties are computed.

Weinberg, B. C.↗
NASA NTRS1986

Fluid flow meter for measuring the rate of fluid flow in a conduit

A tube fluid flow rate meter consists of a reservoir divided by flexible diaphragm into two separate isolated compartments. The incoming and outgoing tubes open into the compartments. The orifice is sized to allow maximum tube fluid flow. Opposing compression springs are secured within the two compartments on opposite sides of the orifice to maintain orifice position when the tube fluid pressure is zero. A tapered element is centered in, and extends through the orifice into the compartment, leaving an annular opening between the element and the perimeter of the oriface. The size varies as the diaphragm flexes with changes in the tube fluid pressure to change the fluid flow through the opening. The light source directs light upon the element which in turn scatters the light through the opening into the compartment. The light detector in the compartment senses the scattered light to generate a signal indicating the amount of fluid.

White, P. R.↗
NASA NTRS1987

Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. 1: Measurement and analysis technique

This two-part paper presents laser anemometer measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan. The objective is to provide additional insight into unsteady blade-row interactions within high speed compressors which affect stage efficiency, energy transfer, and other design considerations. Part 1 describes the measurement and analysis techniques used for resolving the unsteady flow field features. The ensemble-average and variance of the measured velocities are used to identify the rotor wake generated and unresolved unsteadiness, respectively. (Rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and the term unresolved unsteadiness refers to all remaining contributions to unsteadiness such as vortex shedding, turbulence, mass flow fluctuations, etc.). A procedure for calculating auto and cross correlations of the rotor wake generated and unresolved unsteady velocity fluctuations is described. These unsteady-velocity correlations have significance since they also result from a decomposition of the Navier-Stokes equations. This decomposition of the Navier-Stokes equations resulting in the velocity correlations used to describe the unsteady velocity field will also be outlined in this paper.

Suder, K. L.↗
NASA NTRS1987

Two-phase flow measurements of a spray in a turbulent flow

The dynamics of spray drop interaction with a turbulent coflowing air stream were investigated using a Phase Doppler Particle Analyzer that determines both drop size and velocity. Detailed measurements obtained included spray drop size, axial and radial velocity, angle of trajectory, drop Reynolds number, and size-velocity correlations. The gas-phase flow field was also ascertained via the behavior of the smallest drops. Also investigated were the drag coefficients of droplets in a turbulent air cross flow for both monodispersions and polydispersions. Most notable aspects of the coflow included the effect of air streams with velocities significantly different from the spray sheet. Local changes in number density were produced as a result of lateral convection and streamwise accelerations and decelerations of various drop size classes. The complexity of the spray field interaction illustrated by this data effectively describes the development of the spray due to the influence of the airflow. The droplet drag measurements showed similar behavior for monodispersed and polydispersed flows and similar trends to previously obtained data. The measurements also pointed out further studies which would assist in creating an improved drag law for polydispersed drops in a turbulent environment.

Rudoff, R. C.↗
NASA NTRS1987

An experimental study on the effects of tip clearance on flow field and losses in an axial flow compressor rotor

Detailed measurement of the flow field in the tip region of a compressor rotor was carried out using a Laser Doppler Velocimeter (LDV) and a Kiel probe at two different tip clearance heights. At both clearance sizes, the relative stagnation pressure and the axial and tangential components of relative velocities were measured upstream, inside the passage and downstream of the rotor, up to about 20 percent of the blade span from the annulus wall. The velocities, outlet angles, losses, momentum thickness, and force defect thickness are compared for the two clearances. A detailed interpretation of the effect of tip clearance on the flow field is given. There are substantial differences in flow field, on momentum thickness, and performance as the clearance is varied. The losses increase linearly within the passage and their values increase in direct proportion to tip clearance height. No discernable vortex (discrete) is observed downstream of the rotor.

Lakshminarayana, B.↗
NASA NTRS1987

Intergration effects of D-shaped, underwing, aft-mounted, separate-flow, flow-through nacelles on a high-wing transport

An experimental investigation was conducted in the Langley 16-Foot Transonic Tunnel at freestream Mach numbers from 0.70 to 0.82 and angles of attack from -3.0 to 4.0 deg to determine the integration effects of D-shaped, underwing, aft-mounted, separate-flow, flow-through nacelles on a high-wing transonic transport configuration. The results showed that the aft-mounted nacelle/pylon produced an increase in lift over that of the wing-body configuration by pressurizing much of the wing lower surface in front of the pylon. For the D-shaped nacelle, a substantial region of supersonic flow over the wing, aft of the lip of the nacelle, cancelled the reduction in drag caused by the increase in pressures ahead of the lip, to increase interference and form drag compared with a similar circular-shaped nacelle. The installed drag of the D=shaped nacelle was essentially the same as that of an aft-mounted circular nacelle from a previous investigation.

Lamb, Milton↗
NASA NTRS1987

Graphics and Flow Visualization of Computer Generated Flow Fields

Flow field variables are visualized using color representations described on surfaces that are interpolated from computational grids and transformed to digital images. Techniques for displaying two and three dimensional flow field solutions are addressed. The transformations and the use of an interactive graphics program for CFD flow field solutions, called PLOT3D, which runs on the color graphics IRIS workstation are described. An overview of the IRIS workstation is also described.

Kathong, M.↗
NASA NTRS1987

Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. I - Measurement and analysis technique

This two-part paper presents laser anemometer measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan. The objective is to provide additional insight into unsteady blade-row interactions within highspeed compressors which affect stage efficiency, energy transfer, and other design considerations. Part 1 describes the measurement and analysis techniques used for resolving the unsteady flow field features. The ensemble-average and variance of the measured velocities are used to identify the rotor wake generated and unresolved unsteadiness, respectively. (Rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and the term unresolved unsteadiness refers to all remaining contributions to unsteadiness such as vortex shedding, turbulence, mass flow fluctutions, etc.). A procedure for calculating auto and cross correlations of the rotor wake generated and unresolved unsteady velocity fluctuations is described. These unsteady-velocity correlations have significance since they also result from a decomposition of the Navier-Stokes equations. This decomposition of the Navier-Stokes equations resulting in the velocity correlations used to describe the unsteady velocity field will also be outlined in this paper.

Suder, K. L.↗
NASA NTRS1989

Noise produced by turbulent flow into a rotor: Theory manual for atmospheric turbulence prediction and mean flow and turbulence contraction prediction

Prediction of helicopter main rotor noise due to ingestion of atmospheric turbulence was analyzed. The analysis combines several different models that describe the fluid mechanics of the turbulence and the ingestion process. Two models, atmospheric turbulence, and mean flow and turbulence contraction were covered. The third model, covered in a separate report, describes the rotor acoustic mode. The method incorporates the atmospheric turbulence model and a rapid distortion turbulence contraction description to determine the statistics of the anisotropic turbulence at the rotor plane. The analytical basis for a module was provided which was incorporated in NASA's ROTONET helicopter noise prediction program. The mean flow and turbulence statistics associated with the atmospheric boundary layer were modeled including effects of atmospheric stability length, wind speed, and altitude. The turbulence distortion process is modeled as a deformation of vortex filaments (which represent the turbulence field) by a mean flow field due to the rotor inflow.

Simonich, J. C.↗
NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

The present analyses of boundary layer flow and turbulence transport attempt to characterize the influence of freestream turbulence on the surface heat-transfer rate and stagnation point region skin friction of a circular cross-section cylinder in turbulent flow. The Reynolds stress-transport equations and k-epsilon two-equation turbulence modeling are used, yielding time-averaged turbulence double-correlations, mean-flow properties, surface heat-transfer rate, and skin-friction with freestream isotropic turbulence. A comparison of analytical results with experimental data indicates that large Reynolds normal stresses are induced at the boundary layer edge by the kinetic energy of the turbulence.

Wang, C. R.↗
NASA NTRS1989

Three-dimensional computations of cross-flow injection and combustion in a supersonic flow

A low-storage version of the SPARK3D code which is based on the temporally second-order accurate MacCormack (1969) explicit scheme is used to solve the governing equations for three-dimensional chemically reacting flows with finite-rate chemistry. The code includes a fourth-order compact spatial scheme capable of providing higher order spatial accuracy, and it is used to study two-dimensional linear advection, two-dimensional Euler flow, and three-dimensional viscous flow. Also considered are the injection, mixing, and combustion of hydrogen in a supersonic cross stream.

Carpenter, M. H.↗