Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Calibration of the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel (1996 and 1997 Tests)

There were several physical and operational changes made to the NASA Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel during the period of 1992 through 1996. Following each of these changes, a facility calibration was conducted to provide the required information to support the research test programs. Due to several factors (facility research test schedule, facility downtime and continued facility upgrades), a full test section calibration was not conducted until 1996. This calibration test incorporated all test section configurations and covered the existing operating range of the facility. However, near the end of that test entry, two of the vortex generators mounted on the compressor exit tailcone failed causing minor damage to the honeycomb flow straightener. The vortex generators were removed from the facility and calibration testing was terminated. A follow-up test entry was conducted in 1997 in order to fully calibrate the facility without the effects of the vortex generators and to provide a complete calibration of the newly expanded low speed operating range. During the 1997 tunnel entry, all planned test points required for a complete test section calibration were obtained. This data set included detailed in-plane and axial flow field distributions for use in quantifying the test section flow quality.

Arrington, E. Allen↗
NASA NTRSDate not supplied

Comparison of Convective Heat Transfer Correlations and Their Application to Nuclear Thermal Propulsion Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Experiment↗
NASA NTRS1974

Theoretical surface velocity distributions on acoustic splitter geometries for an engine inlet

The potential-flow velocity distributions on several splitter geometries in an engine inlet and their variation with different splitter leading-edge shapes and distances from the inlet highlight were analyzed. The velocity distributions on the inner and outer surfaces of the splitters are presented for low-speed and cruise conditions. At zero incidence angle, the splitter with the 4-to-1 elliptical leading edge had lower peak velocities and velocity gradients than the splitter with the 2-to-1 elliptical leading edge. The velocity gradients decreased as the distance from the inlet highlight to the splitter leading edge was increased. For a given distance, the peak velocity on the splitter inner surface increased with increasing inlet incidence angle. At an incidence angle of 50 deg, the velocity level and gradients on the inner surface of the splitter in the forward position were sufficiently severe to suggest local separation.

Albers, J. A.↗
NASA NTRS1974

Calculation of turbulent shear stress in supersonic boundary layer flows

Turbulent shear stress distributions for supersonic boundary layer flows have been computed from experimental mean boundary layer data. The computations have been made by numerically integrating the time averaged continuity and streamwise momentum equations. Distributions have been obtained for flows upstream and downstream of shock-wave-boundary layer interactions and for both two-dimensional and axisymmetric flows. The computed results are compared with recently reported shear stress measurements which were obtained by hot wire anemometer and laser velocimeter techniques.

Sun, C. C.↗
NASA NTRS1992

Investigation of advancing front method for generating unstructured grid

The advancing front technique is used to generate an unstructured grid about simple aerodynamic geometries. Unstructured grids are generated using VGRID2D and VGRID3D software. Specific problems considered are a NACA 0012 airfoil, a bi-plane consisting of two NACA 0012 airfoil, a four element airfoil in its landing configuration, and an ONERA M6 wing. Inviscid time dependent solutions are computed on these geometries using USM3D and the results are compared with standard test results obtained by other investigators. A grid convergence study is conducted for the NACA 0012 airfoil and compared with a structured grid. A structured grid is generated using GRIDGEN software and inviscid solutions computed using CFL3D flow solver. The results obtained by unstructured grid for NACA 0012 airfoil showed an asymmetric distribution of flow quantities, and a fine distribution of grid was required to remove this asymmetry. On the other hand, the structured grid predicted a very symmetric distribution, but when the total number of points were compared to obtain the same results it was seen that structured grid required more grid points.

Thomas, A. M.↗
NASA NTRS1995

PATHFINDER: Probing Atmospheric Flows in an Integrated and Distributed Environment

PATHFINDER is a software effort to create a flexible, modular, collaborative, and distributed environment for studying atmospheric, astrophysical, and other fluid flows in the evolving networked metacomputer environment of the 1990s. It uses existing software, such as HDF (Hierarchical Data Format), DTM (Data Transfer Mechanism), GEMPAK (General Meteorological Package), AVS, SGI Explorer, and Inventor to provide the researcher with the ability to harness the latest in desktop to teraflop computing. Software modules developed during the project are available in the public domain via anonymous FTP from the National Center for Supercomputing Applications (NCSA). The address is ftp.ncsa.uiuc.edu, and the directory is /SGI/PATHFINDER.

Wilhelmson, R. B.↗
NASA NTRS1965

Digital Distributed Parameter Model for Analysis of Unsteady Flow in Liquid-Filled Lines

A distributed parameter model for computing unsteady flow conditions in liquid systems is presented. The model is adapted for use in conjunction with a digital computer. The analytical method employed is essentially a solution synthesized from the effects of incremental step pressure pulses. The pressure pulses are generated because of incremental flow-rate changes that originate in a fluid system from a variety of sources, including the mechanical motion of the system structure. The pressure pulses propagate throughout the system at sonic velocity and are partially transmitted and reflected at each discontinuity. The velocity change caused by each pressure pulse is obtained from the relation for the characteristic acoustic impedance. Pressure and velocity time histories at any point in the system are obtained by a timewise summation of the contributions of the incremental pressure pulses passing that point. The analysis is presented in a form general enough to be applied to a variety of liquid-filled fluid systems. To illustrate the application of the method to a specific system, the response of a long, straight propellant line to a sinusoidal inlet flow and pressure perturbation is computed. Both a constant-cross-section line and a tapered line are analyzed in the example.

UNSTEADY FLOW↗
NASA NTRS1986

Plasma diagnostics package measurements of ionospheric ions and Shuttle-induced perturbations

The plasma diagnostics package (PDP) on the Space Shuttle STS-3 mission in March 1982 carried among its instrument complement a retarding potential analyzer. This instrument measured both the ambient ion plasma density and temperature, and perturbations to the plasma produced by Shuttle Orbiter effects. Whenever the plasma flow streamline at the instrument was more than a distance of the order of thermal ion gyroradii away from any Orbiter surface, the measurements were characteristic of the ambient ionosphere. In several situations, the PDP was positioned so as to scan the wake in the plasma flow produced by Orbiter surfaces. The density profile of the major species O(+) was consistent with a classic Mach cone. However, strong perturbations extended for several meters outside the Mach cone, which resulted in failure of flowing Maxwellian distributions to represent the data. Configurations where the plasma-flow-impacted Orbiter surfaced downstream of the PDP resulted in generation of a suprathermal ion component. The observations are discussed in terms of a recent model of the mechanism for generation of Shuttle glow.

Reasoner, David L.↗
NASA NTRS1985

In-flight surface oil-flow photographs with comparisons to pressure distribution and boundary-layer data

Upper surface oil-flow photographs were obtained at transonic speeds on an F-111 transonic aircraft technology (TACT) aircraft, which had been fitted with a natural laminar-flow airfoil section. The oil-flow photographs were interpreted with regard to shock and boundary-layer characteristics and compared to results obtained from pressure distributions and boundary-layer measurements. Results indicated that flow phenomena (such as shock location and strength) and chord location of boundary-layer characteristics (such as transition location) could be correctly identified from the oil-flow photographs.

Meyer, Robert R., Jr.↗
NASA NTRS1987

The spatially nonuniform convergence of the numerical solution of flows

The spatial distribution of the numerical disturbances that are generated during the numerical solution of a flow is examined. It is shown that the distribution of the disturbances is not uniform. In regions where the structure of a flow is simple, the magnitude of the generated disturbances is small and their decay is fast. However, in complex flow regions, as in separation and vortical areas, large magnitude disturbances appear and their decay may be very slow. The observed nonuniformity of the numerical disturbances makes possible the reduction of the calculation time by application of what may be called the partial-grid calculation technique, in which a major part of the calculation procedure is applied in selective subregions, where the velocity disturbances are large, and not within the whole grid. This technique is expected to prove beneficial in large-scale calculations such as the flow about complete aircraft configurations at high angle of attack. Also, it has been shown that if the Navier-Stokes equations are written in a generalized coordinate system, then in regions in which the grid is fine, such as near solid boundaries, the norms become infinitesimally small, because in these regions the Jacobian has very large values. Thus, the norms, unless they are unscaled by the Jacobians, reflect only the changes that happen at the outer boundaries of the computation domain, where the value of the Jacobian approaches unity, and not in the whole flow field.

Panaras, Argyris G.↗
NASA NTRS1989

The spatially non-uniform convergence of the numerical solutions of flows

The spatial distribution of the numerical disturbances that are generated during the numerical solution of a flow is examined. It is shown that the distribution of the disturbances is not uniform. In regions where the structure of a flow is simple, the magnitudes of the generated disturbances is small and their decay is fast. However, in complex flow regions, as in separation and vortical areas, large magnitude disturbances appear and their decay may be very slow. The observed nonuniformity of the numerical disturbances makes possible the reduction of the calculation time by application of what may be called the partial-grid calculation technique, in which a major part of the calculation procedure is applied in selective subregions, where the velocity disturbances are large, and not within the whole grid. This technique is expected to prove beneficial in large-scale calculations such as the flow about complete aircraft configurations at high angle of attack. Also, it has been shown that if the Navier-Stokes equations are written in a generalized coordinate system, then in regions in which the grid is fine, such as near solid boundaries, the norms become infinitesimally small, because in these regions the Jacobian has very large values. Thus, the norms, unless they are unscaled by the Jacobians, reflect only the changes that happen at the outer boundaries of the computation domain, where the value of the Jacobian approaches unity, and not in the whole flow field.

Panaras, Argyris G.↗
NASA NTRS1989

Measured and predicted aerodynamic heating on a cylinder in wake of AFE configuration at incidence

Thin-film resistance gages were used to measure cylinder surface heat-transfer rates in the near wake of the Aeroassist Flight Experiment vehicle configuration, while surface-streamline directions were ascertained by the oil-flow techniques under the same configuration and test conditions. Both heat transfer distributions and flow over the entire cylinder surface were influenced by impingement of that portion of the free shear layer originating at the forebody shoulder in the upper symmetry plane. Heating rate distributions predicted with a Navier-Stokes solver computer code were in general agreement with measurements.

Wells, William L.↗
NASA NTRS1992

Application of computational fluid dynamics to the design of the film cooled STME subscale nozzle for the National Launch System

The status of computational fluid dynamics (CFD) calculations for the Space Transportation Main Engine (STME) film/dump cooled nozzle design is presented, with an emphasis on the timely impact of CFD on the design of the sub-scale nozzle coolant system. The following aspects of the sub-scale coolant delivery system were analyzed with CFD: 1) a design trade study of a mechanical flow splitting device for uniform distribution of the subsonic cavity flow, 2) a design trade study of the subsonic cavity lip to achieve film integrity, and 3) an analysis of the primary flow interaction with the core/secondary coolant streams. All design calculations were performed with the Generalized Aerodynamic Simulation Program (GASP), a 3-D, multi-block, generalized Navier-Stokes code capable of solving with frozen, finite-rate or equilibrium chemical kinetics. The initial design of the subsonic cavity flow used square posts to distribute the sonic orifice jets into a uniform flow. Calculations for this design indicated that an unacceptable mal-distribution of film occurred. Design modifications involving curved and slotted posts were computed in an effort to uniformly distribute the secondary coolant flow. Analysis of these configurations showed that although the flowfield improved in uniformity, it was still unacceptable, especially at higher feed pressures. Results from these studies were then incorporated into a design that resulted in the insertion of a porous metal ring into the subsonic cavity. Subsequent water flow model studies showed that this concept was successful in uniformly distributing flow exiting the cavity. In addition to the design of the subsonic cavity, CFD was also used to analyze the secondary coolant lip and the primary flow interaction with the core/secondary coolant streams. A series of calculations were first performed to modify the subsonic cavity lip contour. The flow over the modified lip was then computed simultaneously with the primary injectors to determine the impact of the subsonic coolant stream on the primary slot jets. Pressure, temperature, velocity, and coolant mass fraction contours are presented for these configurations. Information is given in viewgraph form.

Garrett, Joseph L.↗
NASA NTRS1981

Some observations of surface pressures and the near wake of a blunt trailing edge airfoil

Experiments with a truncated and untruncated airfoils of profiles NACA 640A10, were carried out in subsonic wind tunnels in a velocity range of 19m/s to 54m/s corresponding to Reynolds numbers of 200,000 to 468,000 based on the chord. Airfoil spanned the test section to achieve two dimensionality of the model. Velocity measurements, pressure measurements, and vortex shedding in the wake were measured using a hotwire and pressure transducers. The measured chordwise static pressure distribution on the smooth trailing edge airfoil along the midspan plane, agreed with the theoretical results calculated on the basis of the potential flow for that airfoil. Boundary layer profiles measured in the midspan plane, behind the maximum thickness of the airfoil show no separation of the flow. Spanwise distribution of the measured static pressure on the upper surface of the airfoil shows uniformity for both configurations with and without the boundary layer trip. This uniformity of pressure distribution and separation indicates that the flow on the airfoil was uniform and two dimensional in character.

Digumarthi, R. V.↗
NASA NTRS1994

2-D and 3-D oscillating wing aerodynamics for a range of angles of attack including stall

A comprehensive experimental investigation of the pressure distribution over a semispan wing undergoing pitching motions representative of a helicopter rotor blade was conducted. Testing the wing in the nonrotating condition isolates the three-dimensional (3-D) blade aerodynamic and dynamic stall characteristics from the complications of the rotor blade environment. The test has generated a very complete, detailed, and accurate body of data. These data include static and dynamic pressure distributions, surface flow visualizations, two-dimensional (2-D) airfoil data from the same model and installation, and important supporting blockage and wall pressure distributions. This body of data is sufficiently comprehensive and accurate that it can be used for the validation of rotor blade aerodynamic models over a broad range of the important parameters including 3-D dynamic stall. This data report presents all the cycle-averaged lift, drag, and pitching moment coefficient data versus angle of attack obtained from the instantaneous pressure data for the 3-D wing and the 2-D airfoil. Also presented are examples of the following: cycle-to-cycle variations occurring for incipient or lightly stalled conditions; 3-D surface flow visualizations; supporting blockage and wall pressure distributions; and underlying detailed pressure results.

Piziali, R. A.↗