Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID INJECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗
DOE OSTI2023

Stream lamination and rapid mixing in a microfluidic jet for X-ray spectroscopy studies

Microfluidic mixers offer new possibilities for the study of fast reaction kinetics down to the microsecond time scale, and methods such as soft X-ray absorption spectroscopy are powerful analysis techniques. These systems impose challenging constraints on mixing time scales, sample volume, detection region size and component materials. The current work presents a novel micromixer and jet device which aims to address these limitations. The system uses a so-called ‘theta’ mixer consisting of two sintered and fused glass capillaries. Sample and carrier fluids are injected separately into the inlets of the adjacent capillaries. At the downstream end, the two streams exit two micron-scale adjoining nozzles and form a single free-standing jet. The flow-rate difference between the two streams results in the rapid acceleration and lamination of the sample stream. This creates a small transverse dimension and induces diffusive mixing of the sample and carrier stream solutions within a time scale of 0.9 microseconds. The reaction occurs at or very near a free surface so that reactants and products are more directly accessible to interrogation using soft X-ray. We use a simple diffusion model and quantitative measurements of fluorescence quenching (of fluorescein with potassium iodide) to characterize the mixing dynamics across flow-rate ratios.

Huyke, Diego A. (ORCID:0000000283356613)↗
DOE OSTI2013

Modifications of Carbonate Fracture Hydrodynamic Properties by CO 2 -Acidified Brine Flow

Acidic reactive flow in fractures is relevant in subsurface activities such as CO{sub 2} geological storage and hydraulic fracturing. Understanding reaction-induced changes in fracture hydrodynamic properties is essential for predicting subsurface flows such as leakage, injectability, and fluid production. In this study, x-ray computed tomography scans of a fractured carbonate caprock were used to create three dimensional reconstructions of the fracture before and after reaction with CO{sub 2}-acidified brine (Ellis et al., 2011, Greenhouse Gases: Sci. Technol., 1:248-260). As expected, mechanical apertures were found to increase substantially, doubling and even tripling in some places. However, the surface geometry evolved in complex ways including ‘comb-tooth’ structures created from preferential dissolution of calcite in transverse sedimentary bands, and the creation of degraded zones, i.e. porous calcite-depleted areas on reacted fracture surfaces. These geometric alterations resulted in increased fracture roughness, as measured by surface Z{sub 2} parameters and fractal dimensions D{sub f}. Computational fluid dynamics (CFD) simulations were conducted to quantify the changes in hydraulic aperture, fracture transmissivity and permeability. The results show that the effective hydraulic apertures are smaller than the mechanical apertures, and the changes in hydraulic apertures are nonlinear. Overestimation of flow rate by a factor of two or more would be introduced if fracture hydrodynamic properties were based on mechanical apertures, or if hydraulic aperture is assumed to change proportionally with mechanical aperture. The differences can be attributed, in part, to the increase in roughness after reaction, and is likely affected by contiguous transverse sedimentary features. Hydraulic apertures estimated by the 1D statistical model and 2D local cubic law (LCL) model are consistently larger than those calculated from the CFD simulations. In addition, a novel ternary segmentation method was devised to handle the degraded zones, allowing for a bounding analysis of the effects on hydraulic properties. We found that the degraded zones account for less than 15% of the fracture volume, but cover 70% to 80% of the fracture surface. When the degraded zones are treated as part of the fracture, the fracture transmissivities are two to four times larger because the fracture surfaces after reaction are not as rough as they would be if one considers the degraded zone as part of the rock. Therefore, while degraded zones created during geochemical reactions may not significantly increase mechanical aperture, this type of feature cannot be ignored and should be treated with prudence when predicting fracture hydrodynamic properties.

roughness↗
DOE OSTI2013

Forsterite [Mg 2 SiO 4 )] Carbonation in Wet Supercritical CO 2 : An in Situ High-Pressure X-ray Diffraction Study

Technological advances have been significant in recent years for managing environmentally harmful emissions (mostly CO2) resulting from combustion of fossil fuels. Deep underground geologic formations are emerging as reasonable options for long term storage of CO2 but mechanisms controlling rock and mineral stability in contact with injected supercritical fluids containing water are relatively unknown. In this paper, we discuss mineral transformation reactions occurring with forsterite (Mg2SiO4) exposed to wet supercritical CO2. Forsterite was selected as it is an important olivine group mineral present in igneous and mafic rocks and has been the subject of a large number of aqueous dissolution studies that can be compared with non-aqueous fluid tests in this study. Transformation reactions were examined by in situ high pressure x-ray diffraction in the presence of supercritical carbon dioxide (scCO2) containing dissolved water at conditions relevant to carbon sequestration. Under modest pressures (90 bar) and temperatures (50°C), scCO2 saturated with water was found to convert >70 wt% forsterite to a hydrated magnesium carbonate, nesquehonite (MgCO3 •3H2O) and magnesite (MgCO3), after 72 hours of reaction. However, comparable tests with scCO2 at only partial water saturation (82%) showed a significantly slower carbonation rate with only ~30-39 wt% conversion to nesquehonite and no evidence of the anhydrous form (MgCO3). Further decreases in water content of the scCO2 continued to reduce the extent of carbonation, until a critical moisture threshold (~30%) was crossed where forsterite no longer reacted in the presence of the wet scCO2 to form crystalline carbonates. Increasing the temperature to 75°C produced anhydrous magnesium carbonate, magnesite (MgCO3), preceded by the intermediate phase, hydromagnesite [Mg(CO3)4(OH)2 •4H2O]. Measurements conducted during in situ IR experiments at 50°C and 30% saturation identified the presence of an amorphous carbonate phase as well as the formation of a thin liquid-like water layer on the forsterite surface. The presence of this water film appears to be critical for the mineral carbonation of forsterite exposed to water bearing scCO2. In contrast, our prior studies with the mineral brucite [Mg(OH)2] showed extensive carbonation in the absence of a condensed water layer on the mineral surface. The contrasts in reaction rate and products formed demonstrated by temperature and water-content dependence highlights the importance of these kinds of studies to help enable better predictions of the long term fate of geologically stored CO2.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Collapse of Reacted Fracture Surface Decreases Permeability and Frictional Strength

Abstract Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present risks of leakage and seismicity. This study investigated how acidic fluid flow affects hydraulic and frictional properties of fractures using experiments with 3.8‐cm‐long specimens of Eagle Ford shale, a laminated shale with carbonate‐rich strata. In low‐pressure flow cells, one set of samples was exposed to acidic brine and another set was exposed to neutral brine. X‐ray computed tomography and energy‐dispersive X‐ray spectroscopy revealed that samples exposed to acidic brine were calcite‐depleted and had developed a porous altered layer, while the other set showed no evidence of alteration. After reaction, samples were compressed and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compression, the porous altered layer collapsed into fine particles that filled the fracture. This effectively impeded flow and sealed the fracture, resulting in fracture permeability to decrease 1 to 2 orders of magnitude relative to the unaltered fractures. This is a favorable outcome in subsurface applications where the goal is to reduce leakage risks. However, during shear the reacted fracture had lower frictional strength because the fine‐grained particles in the collapsed layer prevented the formation of interlocking microasperities. Therefore, coupled geochemical and geomechanical processes that could favorably seal fractures could also increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.

58 GEOSCIENCES↗
DOE OSTI2022

Molecular-scale mechanisms of CO 2 mineralization in nanoscale interfacial water films

The calamitous impacts of untethered carbon emission from fossil-fuel-burning energy infrastructure calls for accelerated development of large-scale CO 2 capture, utilization, and storage technologies that are underpinned by fundamental understanding of molecular-level chemical processes. In the subsurface, rocks rich in divalent metals can react with CO 2 , permanently sequestering it in the form of stable metal carbonate minerals, with the CO 2 -H 2 O composition of the post-injection pore fluid acting as a primary control variable. Herein, we compare mechanistic reaction pathways for aqueous-mediated carbonation with carbon mineralization occurring in nanoscale adsorbed water films. In the extreme of pores filled with a CO 2 -dominant fluid, carbonation reactions are confined to nanometer-thick water films coating mineral surfaces, which enable metal cation release, transport, nucleation, and crystallization of metal carbonate minerals. Though seemingly counterintuitive, laboratory studies have demonstrated facile carbonation rates in these low water environments, which in recent years has begun to be better understood in mechanistic detail. The overarching objective of this review is to delineate the unique underlying molecular-scale reaction mechanisms that govern CO 2 mineralization in these reactive and dynamic quasi-2D interfaces. Here. we highlight the importance of understanding unique properties in thin water films, such as how water dielectric properties, and consequently ion solvation/hydration behavior, can change under nanoconfinement. We conclude by identifying important frontiers for future work and opportunities to exploit these fundamental chemical insights for decarbonization technologies in the 21st century.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

VISCOUS BOUNDARY LAYERS OF RADIATION-DOMINATED, RELATIVISTIC JETS. II. THE FREE-STREAMING JET MODEL

We analyze the interaction of a radiation-dominated jet and its surroundings using the equations of radiation hydrodynamics in the viscous limit. In a previous paper we considered the two-stream scenario, which treats the jet and its surroundings as distinct media interacting through radiation viscous forces. Here we present an alternative boundary layer model, known as the free-streaming jet model—where a narrow stream of fluid is injected into a static medium—and present solutions where the flow is ultrarelativistic and the boundary layer is dominated by radiation. It is shown that these jets entrain material from their surroundings and that their cores have a lower density of scatterers and a harder spectrum of photons, leading to observational consequences for lines of sight that look “down the barrel of the jet.” These jetted outflow models may be applicable to the jets produced during long gamma-ray bursts and super-Eddington phases of tidal disruption events.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

A Study of Temperature Distribution and Thermal Stresses in a Hot Rock Due to Rapid Cooling

Thermal stresses may be induced in a hot dry rock when a cold fluid is injected in the well. To study this problem, we look at the thermoelastic response of a hot rock that is suddenly cooled. The cooling is assumed to be either at a constant temperature or at a constant heat flux per unit depth. Our approach is to nondimensionalize the equations and perform a parametric study and look at the temperature distribution and the induced-thermal stresses. The results indicate that depending on the extent of cooling and the cooling time, thermal stresses can be induced. Numerical simulations on sandstone, with an initial uniform temperature of 473 K, are also carried out. The results show that if the cooling is due to the surface temperature maintained at 463 K (10 °C lower than the initial temperature of the hot rock), thermal stresses that are larger than the rock tensile strength could be induced. When the cooling is due to a constant surface heat flux, this temperature can be reached after about 777 days of cooling with a minimum value of a heat flux of -20 W/m.

Tran, Phuoc↗
DOE OSTI2012

Percolation in a Proton Exchange Membrane Fuel Cell Catalyst Layer

Water management in the catalyst layers of proton exchange membrane fuel cells (PEMFC) is confronted by two issues, flooding and dry out, both of which result in improper functioning of the fuel cell and lead to poor performance and degradation. At the present time, the data that has been reported about water percolation and wettability within a fuel cell catalyst layer is limited. A method and apparatus for measuring the percolation pressure in the catalyst layer has been developed based upon an experimental apparatus used to test water percolation in porous transport layers (PTL). The experimental setup uses a pseudo Hele-Shaw type testing where samples are compressed and a fluid is injected into the sample. Testing the samples gives percolation pressure plots which show trends in increasing percolation pressure with an increase in flow rate. A decrease in pressure was seen as percolation occurred in one sample, however the pressure only had a rising effect in the other sample.

08 HYDROGEN↗
DOE OSTI2021

Stress analysis using direct-S wavelets produced by a vertical vibrator

We have determined how to extract the azimuth of maximum horizontal stress (SHmax) in deep rocks by doing a simple 360° mathematical rotation of a downgoing direct-S wavelet generated at the baseplate of a surface-based vertical vibrator. We worked with direct-S wavelets that travel through stressed rocks to a deep horizontal vertical seismic profile (VSP) geophone. We find that the azimuth where a polarity reversal occurs in mathematical rotations of this downgoing direct-S wavelet defines the azimuth of the SHmax in the overlying rocks. We tested this direct-S wavelet rotation method for determining the SHmax azimuth at a site in the Illinois Basin using legacy VSP data acquired in 2013. SHmax azimuths indicated by this simple wavelet-rotation method were determined when vertical vibrators were stationed at zero offset, at far offset, and at different azimuths around a VSP receiver well. These VSP-based SHmax azimuths agreed with the azimuth of the SHmax found by traditional minifrac tests in the VSP receiver well. This simple VSP data analysis procedure for detecting the azimuth of maximum horizontal stress has never, to our knowledge, been reported or discussed in the geophysical literature. This technical finding should be of interest to the worldwide geophysical community, especially to people who need to monitor how stress fields shift when fluids are injected into, or extracted from, deep porous reservoirs.

Geochemistry & Geophysics↗
DOE OSTI2022

EGS Collab Experiment 2: Continuous Broadband Seismic Waveform Data

Two broadband seismometers were installed on the 4100 level and recorded for the duration of EGS Collab Experiment #2. Inspired by published data from similar instruments installed in the Aspo Hard Rock Lab, these long-period instruments aimed to measure the tilting of the drift in response to the injection of fluid into the testbed. One instrument was installed underneath the wellheads in Site A (aka the "battery" alcove) and the other was installed along the east wall of the drift, south of Site B. Due to the feet of gravel (ballast) laid along the floor of the drift, we were unable to anchor the sensors directly to the rock. As a result, the coupling of the sensors to the experiment rock volume is likely poor. In addition, there are a number of noise sources that complicate the interpretation of the data. For example, sensor BBB is installed adjacent (within 3 ft) to the rail line that runs towards the Ross shaft. Trains (motors) run along this line almost daily and produce a large signal in these data. Careful extraction of periods of interest, as well as filtering for specific signals, is necessary. The sensors are Nanometrics Trillium Compact Posthole seismometers, sensitive down to 120 seconds period. They were installed as close to the drift wall and as deep as we could manually excavate (only about 1 ft or so). The holes were leveled with sand and the sensors were placed on a paver before backfilling with sand. The hole was then covered by a bucket filled with insulation to improve the sensor's isolation from daily temperature variations, which are minor but present due to drift ventilation from the surface. Data were recorded on Nanometrics Centaur digitizers at 100 Hz. The full response information is available in the StationXML file provided here, or by querying the sensors through the IRIS DMC (see links below). These instruments were provided free of charge through the IRIS PASSCAL instrument center. The network code is XP and the station codes are BBA and BBB. The waveform data can be queried through the IRIS FDSN server using any method the user likes. One convenient option is to use the Obspy python package: https://docs.obspy.org/packages/obspy.clients.fdsn.html

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Utah FORGE: Seismic DAS and Geophone Borehole Data Processing and 3D Imaging of Vp/Vs Ratio in the 2024 Stimulated Reservoir

This dataset includes a final report and a 3D velocity model derived from seismic DAS and geophone borehole data collected during the April 2024 stimulation of the reservoir at Utah FORGE. The report details the processing of over 50,000 P- and S-wave travel times used in a tomographic inversion to estimate the Vp/Vs ratio, revealing anomalies adjacent to wells 16A and 16B that may be associated with injected fracturing fluids. Additionally, Wadati analysis of more than 27,000 pairs of differential P- and S-wave travel times supports this interpretation with a high Vp/Vs estimate of 1.86, averaged over the dimensions of the earthquake cluster. The accompanying data file provides a 3D model of P- and S-wave velocities and Vp/Vs ratios, structured with spatial coordinates and velocity values.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

A Project Lifetime Approach to the Management of Induced Seismicity Risk at Geologic Carbon Storage Sites

The geologic storage of carbon dioxide (CO 2 ) is one method that can help reduce atmospheric CO 2 by sequestering it into the subsurface. Large-scale deployment of geologic carbon storage, however, may be accompanied by induced seismicity. We present a project lifetime approach to address the induced seismicity risk at these geologic storage sites. This approach encompasses both technical and nontechnical stakeholder issues related to induced seismicity and spans the time period from the initial consideration phase to postclosure. These recommendations are envisioned to serve as general guidelines, setting expectations for operators, regulators, and the public. They contain a set of seven actionable focus areas, the purpose of which are to deal proactively with induced seismicity issues. Although each geologic carbon storage site will be unique and will require a custom approach, these general best practice recommendations can be used as a starting point to any site-specific plan for how to systematically evaluate, communicate about, and mitigate induced seismicity at a particular reservoir.

58 GEOSCIENCES↗
DOE OSTI2019

Long-Period, Long-Duration Seismic Events and Their Probable Role in Reservoir Stimulation and Stage Productivity

Hydraulic fracturing is a well-established technique to extract gas or liquid hydrocarbons from low-permeability formations like shale and tight gas reservoirs. Diffusion of hydrofracturing fluid outward from the stimulated fractures into the target formation produces slip across preexisting fractures and other discontinuities in the rock. Microseismic events recorded by downhole seismic monitoring arrays are a manifestation of associated deformation. Recent investigations suggest that the total cumulative seismic moment of microearthquakes during hydraulic fracturing is only a small portion of the total seismic energy release expected for the fluid volume injected into the formation. These observations suggest that other sources of energy release (such as inelastic deformation), contemporaneous with microseismicity, should be considered as relevant to the hydraulic fracturing process. Recent observations on long period, long duration (LPLD) seismic events suggest that slow slip emission along weaknesses that are misaligned with respect to the present-day stress field are likely an important mechanism of deformation and should be better understood and quantified in reservoir stimulations. In Morgantown, West Virginia, we carried out seismic monitoring of hydraulic fracturing activity using an array of five broadband, three-component surface seismometers. Using this network, we identified 89 high-amplitude, impulsive events and 436 long period, long duration (LPLD) events, with highly emergent waveform characteristics. In these interpreted LPLD events, we observed a significant concentration of energy in the 0.8-3 Hz frequency range. During hydraulic fracturing, LPLD events were found to occur most frequently when the pumping pressure and rate were at or near maximum values. As the main purpose of hydraulic fracturing is to stimulate oil and gas production from the less permeable reservoir, we compared the relative production contribution per stage to the frequency of occurrence of suspected LPLD events. We found positive correlation between the frequency of LPLD events and stage-by-stage gas production, highlighting the potential contribution of slow deformation processes and its effectiveness in the reservoir stimulation.

58 GEOSCIENCES↗
DOE OSTI2023

Interpretation of Fracture Initiation Points by In-Well Low-Frequency Distributed Acoustic Sensing in Horizontal Wells

Summary Low-frequency distributed acoustic sensing (LF-DAS) exploits the optical phase shift of Rayleigh backscatter in fiber-optic cables to obtain distributed measurements of changes in strain and temperature. Fiber-optic cables are often installed for multistage hydraulic fracture diagnostics in horizontal wells. LF-DAS in an untreated well provides far-field strain measurements, while offset wells are hydraulically fractured. Such a configuration is called crosswell LF-DAS sensing. Crosswell LF-DAS measurements have proved useful in diagnosing fracture hits, fracture azimuth, planarity, cluster efficiency, fracture propagation rates, and the dynamic distance to the fracture front. In contrast, in-well LF-DAS is conducted on the actively fractured well. Due to cool fracture fluid being injected at high injection rates, the strain component of the LF-DAS response is largely obscured by temperature changes. In permanent fiber-optic cable installations, distributed temperature sensing (DTS) is often conducted simultaneously with LF-DAS. An opportunity exists to decouple the temperature and strain components of LF-DAS sensors to observe strain changes on in-well LF-DAS. The LF-DAS response is modeled as linearly dependent on strain and temperature changes. Theoretical LF-DAS temperature and strain sensitivity coefficients are derived based on the changes to the index of refraction and length of the fiber. Using the DTS measurements, temperature changes are computed, smoothed, filtered, and compared to the LF-DAS response. Crossplots of the in-well LF-DAS measurements and temperature changes from DTS measurements far from the actively fractured region are used to validate the theoretical sensitivity coefficients. Uncertainty in the temperature component of the LF-DAS response is quantified. The difficulty in corresponding the different spatial and temporal resolutions of the DTS and LF-DAS measurements is overcome by comparing the responses over a moving temporal and spatial window. If the LF-DAS response at the center of the window agrees with the DTS response within uncertainty, the measurement is filtered out. After filtering, the remaining nonzero in-well LF-DAS measurements are due to changes in strain. The data are then visualized in waterfall plots. The results indicate that the theoretical and observed strain and temperature coefficients agree within 10%. After the temperature component of the in-well LF-DAS response is extracted, the remaining nonzero measurements are located primarily within the actively treated region. Locations with peaks in the strain response are interpreted to indicate fracture initiation points. These fracture initiation points are compared with in-well DTS and high-frequency DAS noise measurements across multiple stages to better understand fracture initiation along the horizontal well.

Engineering↗
DOE OSTI2013

Environmental Responses to Carbon Mitigation through Geological Storage

In summary, this DOE EPSCoR project is contributing to the study of carbon mitigation through geological storage. Both deep and shallow subsurface research needs are being addressed through research directed at improved understanding of environmental responses associated with large scale injection of CO 2 into geologic formations. The research plan has two interrelated research objectives. Objective 1: Determine the influence of CO 2 -related injection of fluids on pore structure, material properties, and microbial activity in rock cores from potential geological carbon sequestration sites. Objective 2: Determine the Effects of CO 2 leakage on shallow subsurface ecosystems (microbial and plant) using field experiments from an outdoor field testing facility.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Evolution of Induced Fracture Networks Using Machine Learning Correlation Image Analysis

Enhanced geothermal systems (EGS) can enrich the Nation’s energy portfolio by increasing the amount of renewable baseload power available to the electrical grid. Microseismic activity, due to fluid resource injection and production, provides critical insight into the processes that occur within EGS subsurface fracture networks. To more precisely characterize these fracture networks, we leverage recent advances in deep neural network (DNN) image analysis techniques. Using seismic spectrogram data collected during a meso scale EGS field experiment as image inputs, we developed a new approach to correlate microseismic events. Our results indicate that our chosen DNN is able to estimate the correlation value between highly correlated events (i.e., cross-correlation coefficients greater than approximately 0.7), but has difficulty estimating correlation values between poorly correlated events. In physical systems however, the highly correlated microseismic events are the events of interest. Therefore, this data-driven method has shown potential for improving domestic Energy and Resource Security, advancing the current methods available to image subsurface EGS thermal reservoirs to enhance the availability of clean and reliable energy to the national electric grid.

58 GEOSCIENCES↗
DOE OSTI2021

Deposition, Diagenesis, and Sequence Stratigraphy of the Pennsylvanian Morrowan and Atokan Intervals at Farnsworth Unit

Farnsworth Field Unit (FWU), a mature oilfield currently undergoing CO2-enhanced oil recovery (EOR) in the northeastern Texas panhandle, is the study area for an extensive project undertaken by the Southwest Regional Partnership on Carbon Sequestration (SWP). SWP is characterizing the field and monitoring and modeling injection and fluid flow processes with the intent of verifying storage of CO2 in a timeframe of 100–1000 years. Collection of a large set of data including logs, core, and 3D geophysical data has allowed us to build a detailed reservoir model that is well-grounded in observations from the field. This paper presents a geological description of the rocks comprising the reservoir that is a target for both oil production and CO2 storage, as well as the overlying units that make up the primary and secondary seals. Core descriptions and petrographic analyses were used to determine depositional setting, general lithofacies, and a diagenetic sequence for reservoir and caprock at FWU. The reservoir is in the Pennsylvanian-aged Morrow B sandstone, an incised valley fluvial deposit that is encased within marine shales. The Morrow B exhibits several lithofacies with distinct appearance as well as petrophysical characteristics. The lithofacies are typical of incised valley fluvial sequences and vary from a relatively coarse conglomerate base to an upper fine sandstone that grades into the overlying marine-dominated shales and mudstone/limestone cyclical sequences of the Thirteen Finger limestone. Observations ranging from field scale (seismic surveys, well logs) to microscopic (mercury porosimetry, petrographic microscopy, microprobe and isotope data) provide a rich set of data on which we have built our geological and reservoir models.

04 OIL SHALES AND TAR SANDS↗