Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUEL COMBUSTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Gasoline Compression Ignition (GCI) on a Light-Duty Multi-Cylinder Engine Using a Wide Range of Fuel Reactivities and Heavy Fuel Stratification

Many research studies have focused on utilizing gasoline in modern compression ignition engines to reduce emissions and improve efficiency. Collectively, this combustion mode has become known as gasoline compression ignition (GCI). One of the biggest challenges with GCI operation is maintaining control over the combustion process through the fuel injection strategy, such that the engine can be controlled on a cycle-by-cycle basis. Research studies have investigated a wide variety of GCI injection strategies (i.e., fuel stratification levels) to maintain control over the heat release rate while achieving low temperature combustion (LTC). This work shows that at loads relevant to light-duty engines, partial fuel stratification (PFS) with gasoline provides very little controllability over the timing of combustion. On the contrary, heavy fuel stratification (HFS) provides very linear and pronounced control over the timing of combustion. However, the HFS strategy has challenges achieving LTC operation due to the air handling burdens associated with the high EGR rates that are required to reduce NOx emissions to near zero levels. In this work, a wide variety of gasoline fuel reactivities (octane numbers ranging from < 40 to 87) were investigated to understand the engine performance and emissions of HFS-GCI operation on a multi-cylinder light-duty engine. The results indicate that over an EGR sweep at 4 bar BMEP, the gasoline fuels can achieve LTC operation with ultra-low NOx and soot emissions, while conventional diesel combustion (CDC) is unable to simultaneously achieve low NOx and soot. At 10 bar BMEP, all the gasoline fuels were compared to diesel, but using mixing controlled combustion and not LTC.

Dempsey, Adam↗
DOE OSTI2023

High Inlet Temperature Combustor for Direct-Fired Supercritical Oxy-Combustion

It is envisioned that supercritical CO 2 (sCO 2 ) electric power plant efficiencies can exceed 52% with 99% carbon capture using direct-fired oxy-combustion. Such efficiencies would be competitive with Natural Gas Combined Cycles (NGCC) and operate with nearly zero carbon emissions. To achieve high plant efficiencies, turbine inlet conditions must approach 1,200 °C at 250 bar. Such conditions, while desirable from a systems perspective, exceed the current state of the art in turbine design and materials qualification. The team of Southwest Research Institute ® (SwRI ® ), Georgia Institute of Technology (Georgia Tech), Spectral Energies, LLC (Spectral), GE Global Research (GE-GRC), and the University of Central Florida (UCF) sought to demonstrate an intermediate step toward these high efficiency plants with the development of a 1 MWth, subscale direct-fired oxy-fuel combustor. The efforts focused largely on the development of an auto-ignition based combustion system capable of providing the targeted 1200 °C and the pilot-scale plant to operate the combustor. While the project was stopped short of the commissioning and demonstration work, the advances made in this effort will reduce risks associated with chemical kinetics, thermal management, water separation, flue gas cleanup, materials selection, and corrosion in future demonstration efforts for the direct-fired oxy-fuel combustion cycles. The following report documents the design, analysis, and installation efforts completed during the project periods of performance.

03 NATURAL GAS↗
DOE OSTI2022

Impact of coolant temperature on the combustion characteristics and emissions of a stratified-charge direct-injection spark-ignition engine fueled with E30

The direct injection spark ignition (DISI) engine has received considerable attention due to its potential to increase the power density of traditional spark ignition engines while significantly improving fuel economy through lean, unthrottled combustion. However, the market introduction of DISI engines operated in a lean combustion mode is inhibited by their unsatisfactory emissions, especially during cold start conditions that make proper mixture formation more challenging. Ethanol-blended gasoline, now a widely used fuel, makes the cold start of a DISI engine more difficult, leading to higher HC and soot emissions because of the high latent heat of vaporization of ethanol relative to gasoline. This work investigated the impact of coolant temperature on the characteristics of combustion and emissions in a stratified-charge DISI engine fueled with an E30 fuel (i.e. 30% ethanol in gasoline), while the coolant temperature was alternated between four levels (45, 60, 75, and 90 °C) to simulate different conditions throughout the warm-up process. The experiments showed that the coolant temperature affected the post-spark inflammation time, as well as the speed, intensity, and stability of the combustion process in the engine. When the coolant temperature rose, the engine produced more NOX and less CO, PM and HC. In addition, high-speed direct photography was used to obtain crank-angle resolved images of fuel sprays and flames in the cylinder. As the coolant temperature rose, the liquid spray lengths became shorter, reducing the possibility of wall wetting, and reduced irradiance from soot particles also indicated less nonpremixed combustion. The in-cylinder imaging results are consistent with the observed combustion and emission characteristics and shed light on the underlying processes. Finally, some potential solutions to the emissions challenges faced here could be either raising in-cylinder temperatures by using trapped residuals or modifying the injection schedule, for example by increasing the number of injections or to inject later in the cycle into a higher-density environment.

42 ENGINEERING↗
DOE OSTI2022

Detailed Compositional Comparison of Hydrogenated Vegetable Oil with Several Diesel Fuels and Their Effects on Engine-Out Emissions

The Coordinating Research Council (CRC) is actively involved in developing and applying advanced analytical techniques to the chemical characterization of transportation fuels. Here, this article complements a 2017 CRC project to quantify and compare the effects of a commercially available renewable diesel fuel (hydrotreated vegetable oil [HVO]) and an ultralow sulfur diesel (ULSD) fuel on engine-out gaseous and particulate matter (PM) emissions from a light-duty vehicle. Results showed that the combustion of HVO fuel had an advantage over ULSD in terms of lowering engine-out emissions (THC, CO, NO x , etc.). Furthermore, this advantage is strongly related to the fuel composition. This article summarizes the results of advanced and comprehensive analytical tests on the same ULSD and HVO fuels and attempts to connect some of the engine-out emissions results to fuel composition and specific chemical structures. A variety of test methods, generally unavailable in combination, were employed, such as one-dimensional (1D) and two-dimensional (2D) gas chromatography (GC), nuclear magnetic resonance spectroscopy (NMR), and high-pressure solid-liquid phase transition experiments. In summary, the ULSD sample was found to have representation across the expected set of hydrocarbon classes typical for the sample type. Interestingly, a high content of cycloparaffins (>50 wt%) and a very low content of diaromatics (~2 wt%) were present. While not without precedent, these are higher and lower, respectively, than typically found for commercial ULSD compositions. In contrast, HVO was found to consist of only two hydrocarbon classes: n-paraffins (~10 wt%) and iso-paraffins (~90 wt%), both predominantly in a narrow carbon atom number range (i.e., C14–C18). HVO engine-out emissions results for the LA-92 and steady-state testing can be tracked to the narrow carbon atom number range of the n-paraffins and iso-paraffins, which result in a high cetane number fuel having a narrow distillation range. Previously, the low-temperature operability of HVO has been a concern, but that appears not be the case for this particular HVO. HVO and ULSD were evaluated at pressures up to ~275 MPa and found to have comparable solid-liquid equilibria despite significant compositional differences.

09 BIOMASS FUELS↗
DOE OSTI2022

Modeling Freight Traffic Demand and Highway Networks for Hydrogen Fueling Station Planning: A Case Study of U.S. Interstate 75 Corridor

The use of hydrogen as an alternative transportation fuel has gained much interest in recent years. Hydrogen can be utilized in electric vehicles equipped with hydrogen powertrains (including hydrogen internal combustion engines or fuel cells). Given that most of the freight in the U.S. is transported via diesel trucks, transition to hydrogen fuel would help achieve significant environmental benefits as well as accelerate the decarbonization of the freight transportation sector. This paper presents the methodology and results of a case study on modeling freight traffic demand and highway networks based on publicly available data for the Interstate 75 freight corridor. The purpose of this study is to prepare input traffic and network data that can support the planning of a hydrogen fueling station infrastructure. In particular, the data can be used for siting and characterizing an optimized framework of hydrogen fueling stations from candidate diesel stations along the Interstate 75 corridor. The methodologies developed and presented in this paper may be readily expanded and applied to any transport corridor given the data availability. This paper is the first in a series that will build out a comprehensive model to optimize a consolidated national hydrogen refueling infrastructure eco-system targeted at commercial vehicles.

Uddin, Majbah↗
DOE OSTI2022

Combustion dynamics of crude and upgraded Thermal DeOxygenation oils in a compression ignition engine

Thermal DeOxygenation (TDO) is a robust thermochemical conversion scheme to produce hydrocarbons from biomass feedstock. The process targets the carbohydrate fraction of biomass to yield a broad mixture of primarily aromatic hydrocarbons within a boiling point range of 348–798 K with low oxygen content (<4 wt%). The resulting materials are amenable to traditional hydrotreating and distillation processes with approximately 70% by mass in the distillate fuel range. The simple conversion scheme combined with commercially viable upgrading routes makes TDO oils a feasible alternative fuel for transportation applications. Here this paper is the first systematic treatment of fit-for-purpose testing of TDO oils in a compression ignition engine. Blends of partially upgraded TDO oils (e.g. whole oil, distilled oil, hydrotreated oil and hydrotreated-distilled oil) are prepared with certified ultra-low sulfur diesel at 5%, 10%, 15% and 20% by volume. The resulting fuels are analyzed for fuel characteristics and combustion dynamics in an instrumented single-cylinder compression ignition engine. All fuel blends at 10% blend level by volume exhibited adequate engine performance. Hydrotreating of the oils is a necessary step to meet cetane number and EPA soot emissions requirements at 20% blend volume. Combined distillation and hydrotreatment meet or exceed all fuel specification and engine performance benchmarks. Partially upgraded TDO oils are suitable fuel options for compression ignition applications.

42 ENGINEERING↗
DOE OSTI2025

Fuel reid vapor pressure level and ethanol content on stochastic preignition, effects at steady and unsteady engine operation

The present work investigates relations between fuel Reid vapor pressure (RVP) and biofuel (ethanol) content on stochastic preignition (SPI) at both sustained steady-state engine operation and following load transients. This work stems from in-field observations that automotive original equipment manufacturers have observed consistent seasonal increases in United States customer drivability complaints and warranty claims during September and October where SPI is suspected to be responsible. The seasonal timing of these events coincides with the United States seasonal fuel property changeover initiating on September 15 each year, where fuel RVP increases. To explore potential linkage between fuel RVP and SPI the present study employs engine SPI experiments coupled with laboratory spray measurements of fuels with RVPs of 8, 12, and 16 psi in both E10 (10% ethanol) and E25 (25% ethanol) fuels. Engine results are partitioned into fuel RVP and ethanol content effects on SPI in steady-state, sustained high-load engine operation and unsteady-state low- to high-load transitions, where off-engine spray vessel patternation and tip penetration results help to elucidate the observed fuel effects on SPI. A boosted direct-injected, spark-ignition engine was fueled with three market relevant E10 and E25 fuels with RVPs of 8, 12, and 16 to characterize the interplay between winter fuels and abnormal combustion behavior. The steady-state work shows that for high-load, steady-state engine operation, SPI is directly linked to fuel retention, which was found to be dependent on fuel distillation. The unsteady-state engine operation work shows that following low-to high-load transitions, SPI can occur from a memory of fuel property effects at low-load operation. Specifically, the fuel RVP effect on fuel spray collapse at low loads was found to correlate with SPI with a more than 95% confidence interval following low- to high-engine-load transitions. Results suggest that fuel-wall impingement at low-load operation could carry over into high-load transitions and generate SPI events following low- to high-load transitions.

09 BIOMASS FUELS↗
DOE OSTI2024

A Literature Review of NO x Emissions in Current and Future State-of-the-Art Gas Turbines

Current U.S. government policy seeks to achieve a completely carbon-free economy by 2050, with a carbon-free electricity sector by 2035 (per executive orders #14008 and #14057). To address these goals, the U.S. Department of Energy is evaluating strategies and technologies that support the production, utilization, transport, and storage of hydrogen (via initiatives such as Department of Energy's (DOE) Energy Earthshot—Hydrogen and various DOE funding opportunity announcements). A carbon-free fuel such as hydrogen cannot be overvalued in a dynamic electric energy sector seeking to decarbonize. One of the most important technologies needed to achieve the goal of a carbon-free electricity sector is a 100% hydrogen-fueled gas turbine. Accommodating hydrogen-based fuels has been a key goal for various original engine manufacturers (OEMs) for many years, but much more research and development (R&D) is needed. The purpose of this paper is to highlight the current state-of-the- art of hydrogen turbine technology, especially regarding nitrogen oxide (NO X ) emissions compared to natural gas-fueled turbines. NO X is the primary criteria pollutant from thermally driven combustion turbines and should be controlled to levels that are equivalent to or below existing standards (as reported “existing standards” for hydrogen-fueled gas turbines may need to be rebaselined). Further, this paper will provide an overview of hydrogen as a fuel and various NO X emissions control techniques that are relevant for hydrogen-based fuels. A conclusion from this overview is that, with some level of R&D, NO X emissions from hydrogen-fueled gas turbines can be controlled to levels similar to those produced by state-of-the-art (SOTA) natural gas-fueled combustion turbines while remaining competitive in terms of performance and efficiency.

42 ENGINEERING↗
DOE OSTI2020

Influence of Equation-of-States on Supercritical CO2 Combustion Mixtures

Abstract Fossil fuel based direct-fired supercritical CO2 (sCO2) cycles are gaining the attention of industry, academia, and government due to their remarkable efficiency and carbon capture at high-source temperatures. Modeling plays an important role in the development of sCO2 combustors because experiments are very expensive at the designed operating conditions of these direct-fired cycles. Inaccurate density estimates are detrimental to the simulation output. Hence, this work focuses on comprehensive evaluation of the influence and applicability of various equation-of-states (EOS) which are being used in the supercritical combustion modeling literature. A state-of-the-art supercritical combustion modeling methodology is used to simulate counter-flow supercritical CO2 flames by using various equation-of-states. The results show that using the corresponding state principle to evaluate compressibility factor is not accurate. Also, van der Waal type EOSs predictions can be as accurate as complex Benedict–Webb–Rubin EOSs; hence van der Waal EOSs are more suitable to simulate sCO2 combustor simulations. Non-ideal effects are significant under the operating conditions considered in this work. The choice of EOS significantly influences the flame structure and heat release rate. Also, assuming the binary interaction parameter as zero is reasonable in sCO2 combustion simulations.

Energy & Fuels↗
DOE OSTI2024

Zero-RK Acceleration of Low-Life-cycle Carbon Fuel (LLFC)Simulations

Designing modern combustion systems now relies on computer models that predict how changes in design will affect performance. These models have replaced older methods that relied on the designer’s intuition or costly and time-consuming physical testing. By using improved models, design cycles can be shortened and cleaner and more efficient combustion devices can be created. This project aims to improve computer simulations of low-life-cycle carbon fuels (LLCFs) with the goal of making these simulations faster and more accurate for predicting combustion in vehicles.

02 PETROLEUM↗
DOE OSTI2021

Optical Investigation of a Partial Fuel Stratification Strategy to Stabilize Overall Lean Operation of a DISI Engine Fueled with Gasoline and E30

This paper offers new insights into a partial fuel stratification (PFS) combustion strategy that has proven to be effective at stabilizing overall lean combustion in direct injection spark ignition engines. To this aim, high spatial and temporal resolution optical diagnostics were applied in an optically accessible engine working in PFS mode for two fuels and two different durations of pilot injection at the time of spark: 210 µs and 330 µs for E30 (gasoline blended with ethanol by 30% volume fraction) and gasoline, respectively. In both conditions, early injections during the intake stroke were used to generate a well-mixed lean background. The results were compared to rich, stoichiometric and lean well-mixed combustion with different spark timings. In the PFS combustion process, it was possible to detect a non-spherical and highly wrinkled blue flame, coupled with yellow diffusive flames due to the combustion of rich zones near the spark plug. The initial flame spread for both PFS cases was faster compared to any of the well-mixed cases (lean, stoichiometric and rich), suggesting that the flame propagation for PFS is enhanced by both enrichment and enhanced local turbulence caused by the pilot injection. Different spray evolutions for the two pilot injection durations were found to strongly influence the flame kernel inception and propagation. PFS with pilot durations of 210 µs and 330 µs showed some differences in terms of shapes of the flame front and in terms of extension of diffusive flames. Yet, both cases were highly repeatable.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Free-spray characteristics and spray-wall interactions of methanol on a gasoline direct injector under flash-boiling and non-flash-boiling conditions

Methanol is considered a promising alternative fuel for internal combustion engines (ICEs) due to its high-octane number, fast laminar flame speed, and elevated latent heat of vaporization, all of which support higher compression ratios and improved thermal efficiency. However, its substantial latent heat of vaporization also poses cold-start challenges, such as misfire and fuel film deposition. This study aims to investigate methanol spray morphology and spray-wall interaction using the Spray M injector from the Engine Combustion Network within a constant-pressure flow vessel. A recently developed unified numerical framework capable of modeling both flash and non-flash boiling sprays is validated against experimental liquid volume fraction data acquired via 3-D computed tomography. Here, the results reveal that flash boiling significantly alters the spray morphology, leading to smaller droplets and spray collapse due to enhanced air-entrainment-induced turbulence. Quantitative agreement between experiments and simulations confirms this behavior. Coupled 0-D equilibrium and 3-D computational fluid dynamics analyses show that flash boiling accelerates evaporation and reduces fuel residence time, while non-flash conditions maintain a persistent liquid core more susceptible to wall wetting. Wall temperature diagnostics reveal that spray collapse alters heat transfer patterns by shifting cooling effects. Mixture fraction analysis indicates that evaporation is primarily governed by shear-layer turbulence, though deviations from adiabatic equilibrium mixing emerge under low-turbulence conditions. Finally, increasing fuel, ambient, and wall temperatures reduces wall wetting and film thickness, mitigating cold-start risks. These findings enhance the understanding of methanol sprays’ behavior and support its adoption as a viable, alternative fuel for ICEs.

Engine Combustion Network↗
DOE OSTI2024

Kinetics of low temperature plasma assisted NH 3 /H 2 oxidation in a nanosecond-pulsed discharge

Ammonia (NH 3 ) has been widely recognized as one of the carbon-neutral fuels. However, ammonia combustion suffers low reactivity and high N 2 O/NO x emissions. Here, to overcome these issues, this work reports plasma assisted NH 3 /H 2 oxidation and unveils the kinetics of fuel oxidation and N 2 O/NO x formation by combining time-resolved laser diagnostics with plasma modeling. Firstly, we found that the NH 3 consumption is promoted with a H 2 blending ratio of 0.3, due to enhancements of H and OH formation by plasma assisted H 2 dissociation. Secondly, at a high reduced electric field, when the H 2 blending ratio increases, the NH 3 oxidation is promoted due to both the HO 2 formation and strong NO kinetic enhancement via NO-HO 2 and NO 2 -H pathways. In the meantime, it is shown that the NO mole fraction also increases with H 2 blending ratio, because the NO formation is enhanced via N( 2 D)-O 2 pathways, and the DeNO x chemistry is weakened with less NH 2 production. By contrast, at a lower reduced electric field, when the H 2 blending ratio increases, the decreased N( 2 D) formation does not produce enough NO to replenish the NO formation drop caused by lower NH 3 concentration. Thirdly, the reduced electric field non-monotonically affects fuel consumption and N 2 O/NO x formation by manipulating electron energy deposition pathways. The NH 3 consumption is maximized with an optimal reduced electric field where N 2 * excitation and O 2 dissociation are most efficient. When the reduced electric field deviates from its optimum, the NH 3 consumption decreases due to the discharge energy deposition to either vibrational excitation or dissociation of N 2 . The N 2 O/NO x emissions governed by the NH 3 oxidation follow the above NH 3 consumption trend.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Fuel injector with duct assembly

Methods and systems are provided for a fuel injector of an internal combustion engine. In one example, a fuel injector includes a body having a flange shaped to seat within a shoulder of a passage of a cylinder head. The shoulder is positioned at an inner side of the cylinder head such that the fuel injector is coupled to the cylinder head at the inner side by the flange.

Kurtz, Eric↗
DOE OSTI2023

Zero-RK Acceleration of Low-Lifecycle-Carbon Fuel (LLCF) Simulations

Designing modern combustion systems now relies on computer models that predict how changes in design will affect performance. These models have replaced older methods that relied on the designer's intuition or costly and time-consuming physical testing. By using improved models, design cycles can be shortened, and cleaner and more efficient combustion devices can be created. This project aims to improve computer simulations of low-lifecycle-carbon fuels (LLCFs) with the goal of making these simulations faster and more accurate for predicting combustion in vehicles.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Implementation of Surface Tension on a Reacting Flow Solver, PeleLM: Preprint

In liquid rocket engines, the fuel is supplied to the combustion chamber in the liquid state though injectors. Such fuel undergoes atomization, vaporization, and combustion processes. To design reliable and efficient injectors, it is required to understand the full processes. This research is part of an effort to develop a full atomization-vaporization-combustion solver from first principles. As an initial step to tackle the atomization process, a multiphase flow solver is under development. For the development, a library of the volume of fluid scheme for multiphase, IRL is coupled with a reacting Navier-Stokes equation solver, PeleLM. Furthermore, as the surface tension has considerable effects on spray breakup. surface tension is implemented in the momentum equation using the continuum surface force model and the improved height function technique.

height function↗
DOE OSTI2020

Turbine nozzle cooling with panel fuel injector

The present disclosure is directed to a combustion system including a panel fuel injector. The panel fuel injector includes a first side wall, a second side wall, and an aft wall. The first side wall and the second side wall are interconnected by the aft wall. The panel fuel injector further includes a cooling air plenum that is defined between the first side wall and the second side wall. The aft wall defines a plurality of cooling holes in fluid communication with the cooling air plenum. One or more of the cooling holes of the plurality of cooling holes is oriented towards at least one of a leading edge, a pressure side wall, or a suction side wall of a stationary nozzle disposed proximate to the aft end wall.

33 ADVANCED PROPULSION SYSTEMS↗