Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flight Path”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Design and Evaluation of a Dynamic Programming Flight Routing Algorithm Using the Convective Weather Avoidance Model

The optimization of traffic flows in congested airspace with varying convective weather is a challenging problem. One approach is to generate shortest routes between origins and destinations while meeting airspace capacity constraint in the presence of uncertainties, such as weather and airspace demand. This study focuses on development of an optimal flight path search algorithm that optimizes national airspace system throughput and efficiency in the presence of uncertainties. The algorithm is based on dynamic programming and utilizes the predicted probability that an aircraft will deviate around convective weather. It is shown that the running time of the algorithm increases linearly with the total number of links between all stages. The optimal routes minimize a combination of fuel cost and expected cost of route deviation due to convective weather. They are considered as alternatives to the set of coded departure routes which are predefined by FAA to reroute pre-departure flights around weather or air traffic constraints. A formula, which calculates predicted probability of deviation from a given flight path, is also derived. The predicted probability of deviation is calculated for all path candidates. Routes with the best probability are selected as optimal. The predicted probability of deviation serves as a computable measure of reliability in pre-departure rerouting. The algorithm can also be extended to automatically adjust its design parameters to satisfy the desired level of reliability.

Ng, Hok K.↗
NASA NTRS1946

Waters Loads on the XJL-1 Hull as Obtained in Langley Impact Basin, TED No. NACA 2413.3

An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length. of 120 feet and heights ranging from 1 to 4 feet. All data and results presented in this report are given in terms of equivalent full-scale values. Summary tables and illustrative plots are used in presenting the material. The following maximum values of load and pressure are those which are apropos for effective flight paths less than 6.5deg which was the maximum value obtained in tests with the XJL-1 hull model representing full-scale landings with vertical velocity of 4.5 feet per second into 4-foot waves. The maximum local pressure on the flat portion of the bottom is 130 pounds per square inch which was measured on a 2-inch-diameter circular area near the step. The maximum local pressure obtained in the curved area near the chines is 200 pounds per square inch. This pressure was also measured near the step.

Steiner, Margaret F.↗
NASA NTRS1988

In situ northern mid-latitude observations of ClO, O3, and BrO in the wintertime lower stratosphere

In order to test photochemical theories linking chlorofluorocarbon derivatives to O3 depletion at high latitudes in the springtime, several related atmospheric species, including O3, ClO, and BrO were measured in the lower stratosphere. The flight path extended to the center of the polar jet associated with but outside of the Arctic vortex, in which the abundance of O3 was twice its midlatitude value, whereas BrO levels were five parts per trillion (pptv) by volume between 18 and 21 km, and 2.4 pptv below that altitude. The ClO mixing ratio was as much as 65 pptv at 60 N latitude at an altitude of 20 km, and was enhanced over midlatitude values by a factor of three to five at altitudes above 18 km and by as much as a factor of 40 at altitudes below 17 km. Levels of ClO and O3 were highly correlated on all measured distance scales, and both showed an abrupt change in character at 54 N latitude. The ClO abundance north of 54 N was probably caused by low NO2 levels in the flight path.

Brune, W. H.↗
NASA NTRS1992

Optimal recovery from microburst wind shear

The flight path of a twin-jet transport aircraft is optimized in a microburst encounter during approach to landing. The objective is to execute an escape maneuver that maintains safe ground clearance and an adequate stall margin during the climb-out portion of the trajectory. A cost function penalizing rate of climb deviations from a nominal value and rate of elevator deflection produces qualitatively good results in a variety of microburst encounters. The optimal maneuver is a gradual pitch-up that ceases near the core of the microburst, followed by a slight reduction in pitch attitude in the tailwind area of the microburst. A minimum airspeed constraint in the optimization prevents excessive airspeed loss in very severe microbursts. The aircraft equations of motion include short-period dynamics, so that the optimization solves directly for the control surface deflections required to achieve the optimal flight paths.

Mulgund, Sandeep S.↗
NASA NTRS2019

Exploration of Atmospheric Entries at Uranus & Neptune with HEEET as Heatshield TPS

One important observation from the recent Ice Giants Study sponsored by NASA was that the predicted and margined thicknesses of HEEET (new NASA TPS technology) were much greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade would be substantial, the present work explores the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii 0.2 m, 0.3 m, and 0.4 m which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study. For each 3D OF trajectory generated by a NASA Ames in-house code, TRAJ, the material response and thickness were computed using another NASA Ames code, FIAT, along with a margins policy proposed by the HEEET project. In the present work, ballistic coefficients ranging from 200 kg/sqm to 350 kg/sqm were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

Prabhu, Dinesh K.↗
NASA NTRS2019

Ballistic Entries for Saturn, Uranus, and Neptune with HEEET TPS

One important observation from the Ice Giants Study was that the predicted and margined thicknesses of HEEET were greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade could be substantial and time consuming, the present work explored the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii – 0.2 m, 0.3 m, and 0.4 m – which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study. For each 3DOF trajectory generated by a NASA Ames in-house code, TRAJ, the material response and thickness were computed using another NASA Ames code, FIAT, along with a margins policy proposed by the HEEET project. In the present work, ballistic coefficients ranging from 200 kg/sq m to 350 kg/sq m were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

Atmospheric Entry↗
NASA NTRS2019

Exploration of Atmospheric Entries at Uranus & Neptune with HEEET as Heatshield TPS

One important observation from the Ice Giants Study was that the predicted and margined thicknesses of HEEET were greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade would be substantial, the present work explored the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii – 0.2 m, 0.3 m, and 0.4 m – which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study [4] on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study [1]. For each 3DOF trajectory generated by a NASA Ames in-house code, TRAJ [5], the material response and thickness were computed using another NASA Ames code, FIAT [6], along with a margins policy proposed by the HEEET project [7]. In the present work, ballistic coefficients ranging from 200 kg/m2 to 350 kg/m2 were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

HEEET↗
NASA NTRS1981

Flight evaluation of the terminal guidance system

The terminal guidance system (TGS) is avionic equipment which gives guidance along a curved descending flight path to a landing. A Cessna 182 was used as the test aircraft and the TGS was installed and connected to the altimeter, DME, RMI, and gyro compass. Approaches were flown by three different pilots. When the aircraft arrives at the termination point, it is set up on final approach for a landing. The TGS provides guidance for curved descending approaches with guideslopes of 6 deg which required, for experienced pilots, workloads that are approximately the same as for an ILS. The glideslope is difficult to track within 1/2 n.m. of the VOR/DME station. The system permits, for experienced pilots, satisfactory approaches with a turn radius as low as 1/2 n.m. and a glideslope of 6 deg. Turn angles have little relation to pilot workload for curved approaches. Pilot experience is a factor for curved approaches. Pilots with low instrument time have difficulty flying steep approaches with small turn radius. Turbulence increases the pilot workload for curved approaches. The TGS does not correct to a given flight path over the ground nor does it adequately compensate for wind drift.

Sandlin, D. R.↗
NASA NTRS1998

Controller Strategies for Managing Air Traffic in High Altitude Arrival Sectors

Substantial increases in the volume of air traffic in the National Airspace System (NAS) are forecast for the next decade, with the number of passengers travelling on U.S. airlines expected to increase by as much as 60%. This increased demand on system capacity will be accompanied by increases in traffic complexity as air traffic service providers routinely accommodate user preferred routing requests. Changes to the NAS to meet these new demands are currently underway, including development of new decision support tools to aid controllers in monitoring and managing air traffic, and increased air-to-air and air-to-ground information exchange. Changes in roles and responsibilities of pilots and controllers in flight path management will accompany these changes in traffic patterns and information technology, however the ultimate responsibility for maintaining aircraft separation will remain with the air traffic controller. A thorough understanding of the methods controllers use to manage air traffic will help ensure that changes to the NAS are implemented in a way that maintains the controller's ability to separate aircraft as the system evolves. This presentation describes the strategies controllers use today to manage arrival traffic in its descent from cruise altitude to the Terminal Radar Approach Control (TRACON) boundary. Factors that increase the complexity of this task include the presence of overflight traffic, varying aircraft performance characteristics, winds aloft, ground speed variations with altitude, the need to merge arrival traffic into a single stream, and, when arrival traffic exceeds airport runway capacity, the added task of metering flow into the TRACON. Because of the limited information available to controllers to manage arrival traffic, their strategies are often driven by the need to reduce the task's complexity, which can result in de-optimized flight paths for individual aircraft (e.g., sub-optimal descent or speed profiles). Understanding these strategies and the cognitive demands that drive them will support a safe transition to a NAS that relies on enhanced technologies. In addition, it could enable system developers to identify opportunities for new automation-based procedures or information displays that could reduce the controller's workload and increase operational efficiency.

Smith, Nancy↗
NASA NTRS1959

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch- and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 0 dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time throughout the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 300 dead-rise model tests, C(sub Delta)A = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor ofC(sub Delta). For instance, the maximum impact lift coefficient C(sub L,max)is found to be directly proportional to C(sub Delta)(sup 0.33) for the flat-bottom model and C(sub Delta)(sup 0.45) for the 30 deg dead-rise model. These variations of C(sub L,max) C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L,max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to 30 deg, beam-loading coefficients from 0.48 to 544, trim angles from 3 deg to 45 deg and initial flight-path angles from about 2 deg to about 27 deg.

Mixson, John S.↗
NASA NTRS1959

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch-and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 deg dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time through- out the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 30 deg dead-rise model tests, C(sub Delta) = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor of C(sub Delta). For instance, the maximum impact lift coefficient is found C(sub L,max) to be directly proportional to C(sub Delta, exp 0,33) for the flat-bottom model and C(sub Delta, exp 0,45) for the 30 deg dead-rise model. These variations of C(sub L, max) with C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L, max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to deg, beam-loading coefficients from o.48 to 544, trim angles from 3 deg to deg, and initial flight-path angles from about 2 deg to about deg.

Mixson, John S.↗
NASA NTRS1975

Flight experience with time-of-arrival control for STOL aircraft in the terminal area

A research program on STOL operating systems is underway at the Ames Research Center. One investigation is concerned with design, analysis, and flight test of promising four-dimensional RNAV systems. One promising system generates a capture flight path from the present aircraft position to a waypoint on a selected fixed STOL approach route. It predicts arrival time at the runway and controls time and position along the path. The system was flight tested using a digital avionics system on a Convair 340 and on an experimental powered-lift STOL airplane. Flight tests in the flight director mode show that the pilot can choose and change the desired time of arrival, and meet this time within a few seconds, in spite of navigation errors and varying winds. Initial tests of the automatic mode using a flight simulator and the NASA Augmentor Wing Jet STOL Research Aircraft (AWJSRA) show that good time control was achieved at the cost of excess throttle activity. This fault was later corrected.

Neuman, F.↗
NASA NTRS1986

Development and evaluation of an airplane electronic display format aligned with the inertial velocity vector

The development of an electronic primary flight display format aligned with the aircraft velocity vector, a simulation evaluation comparing this format with an electronic attitude-aligned primary flight display format, and a flight evaluation of the velocity-vector-aligned display format are described. Earlier tests in turbulent conditions with the electronic attitude-aligned display format had exhibited unsteadiness. A primary objective of aligning the display format with the velocity vector was to take advantage of a velocity-vector control-wheel steering system to provide steadiness of display during turbulent conditions. Better situational awareness under crosswind conditions was also achieved. The evaluation task was a curved, descending approach with turbulent and crosswind conditions. Primary flight display formats contained computer-drawn perspective runway images and flight-path angle information. The flight tests were conducted aboard the NASA Transport Systems Research Vehicle (TSRV). Comparative results of the simulation and flight tests were principally obtained from subjective commentary. Overall, the pilots preferred the display format aligned with the velocity vector.

Steinmetz, G. G.↗
NASA NTRS1992

Control integration concept for hypersonic cruise-turn maneuvers

Piloting difficulties associated with conducting aircraft maneuvers in hypersonic flight are caused in part by the nonintuitive nature of the aircraft response and the stringent constraints anticipated on allowable angle of attack and dynamic pressure variations. An approach is documented that provides precise, coordinated maneuver control during excursions from a hypersonic cruise flight path and the necessary flight condition constraints. The approach is to achieve specified guidance commands by resolving altitude and cross range errors into a load factor and bank angle command by using a coordinate transformation that acts as an interface between outer and inner loop flight controls. This interface, referred to as a 'resolver', applies constraints on angle of attack and dynamic pressure perturbations while prioritizing altitude regulation over cross range. An unpiloted test simulation, in which the resolver was used to drive inner loop flight controls, produced time histories of responses to guidance commands and atmospheric disturbances at Mach numbers of 6, 10, 15, and 20. Angle of attack and throttle perturbation constraints, combined with high speed flight effects and the desire to maintain constant dynamic pressure, significantly impact the maneuver envelope for a hypersonic vehicle.

Raney, David L.↗
NASA NTRS1991

Global positioning system supported pilot's display

The hardware, software, and operation of the Microwave Scanning Beam Landing System (MSBLS) Flight Inspection System Pilot's Display is discussed. The Pilot's Display is used in conjunction with flight inspection tests that certify the Microwave Scanning Beam Landing System used at Space Shuttle landing facilities throughout the world. The Pilot's Display was developed for the pilot of test aircraft to set up and fly a given test flight path determined by the flight inspection test engineers. This display also aids the aircraft pilot when hazy or cloud cover conditions exist that limit the pilot's visibility of the Shuttle runway during the flight inspection. The aircraft position is calculated using the Global Positioning System and displayed in the cockpit on a graphical display.

Scott, Marshall M., Jr.↗