Search NASA⌕ Search

SEARCH · Search NASA

Results for “Freestream conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Unsteady shock-induced turbulent separation in Mach 5 cylinder interactions

Wall pressure fluctuations have been determined under the unsteady separation shock in interactions generated by unswept circular cylinders, using a nominal freestream Mach number of 5 and a freestream unit Reynolds number of 53 x 10 to the 6th/m. The distributions of shock frequency and period were calculated using a conditional sampling algorithm. The shock frequency distributions were all found to be broadband, with frequencies being typically 1-2 kHz. The results support the previous suggestion that pressure fluctuations in the separated flow drive the shock motion.

Dolling, D. S.↗
NASA NTRS2020

Simulation and Modeling of Cold-Wall Hypersonic Turbulent Boundary Layers on Flat Plate

Direct numerical simulations (DNS) of flat-plate, zero-pressure-gradient turbulent boundary layers are presented for nominal freestream Mach numbers of 11 and 14 and a highly cooled wall (wall-to-recovery temperature of approximately 0.2). The flow conditions of the DNS are representative of the experimental data for a Mach 11.1 turbulent boundary layer on a flat plate that was tested at Calspan–University of Buffalo Research Center (CUBRC) and the operational conditions of the AEDC Hypervelocity Tunnel No. 9 at Mach 14. The wall shear stress and turbulent heat flux predicted by DNS show good comparisons with those measured at CUBRC and those modeled with a Baldwin-Lomax model. The generated DNS database extends the range of Reynolds numbers from those typical of previous DNS studies for hypersonic boundary-layer flows and confirms the validity of Morkovin’s hypothesis within the relatively broader range of Reynolds numbers considered in this study. A priori assessment of turbulent heat flux models with DNS data shows that the algebraic energy flux (AEF) formulation gives better predictions of the streamwise turbulent heat flux than the commonly used constant turbulent Prandtl number model while both models give similarly good predictions of the wall-normal turbulent heat flux. A posteriori assessment shows that the AEF model improves the prediction of the temperature profiles while keeping a good prediction of the velocity field.

Junji Huang↗
NASA NTRS1998

Experimental Study of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. Freestream turbulence levels ranging from 0.8% to 3% was used in this experiment. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. Hot-wires (single and x-wire) and surface mounted hot-film gases and static pressure taps were used to map the flowfield. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗
NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle-of-attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane. At a selected condition from the ascent part of the anticipated flight trajectory, either type of departure from the design condition is shown to have a considerable impact on the structure of the laminar basic state and, hence, also on the amplification characteristics of the instability waves. A broader set of computations, including N-factor predictions for the relevant instabilities, will be presented in the final paper.

Boundary layer transition↗
NASA NTRS1971

Computing incompressible laminar and turbulent boundary layer formation

Program generates initial laminar conditions, such as in Falkner-Skan similarity flows, or turbulent equilibrium profiles. Initial profile input data is used. Combination with inviscid-freestream calculations to predict entire flow field in turbine cascade or around airfoil is possible.

Herring, H. J.↗
NASA NTRS1990

The inviscid stability of supersonic flow past axisymmetric bodies

The supersonic flow past a sharp cone is studied. The associated boundary layer flow (i.e., the velocity and temperature field) is computed. The inviscid linear temporal stability of axisymmetric boundary layers in general is considered, and in particular, a so-called 'triply generalized' inflection condition for 'subsonic' nonaxisymmetric neutral modes is presented. Preliminary numerical results for the stability of the cone boundary layer are presented for a freestream Mach number of 3.8. In particular, a new inviscid mode of instability is seen to occur in certain regimes, and this is shown to be related to a viscous mode found by Duck and Hall (1988).

Duck, Peter W.↗
NASA NTRS1992

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗
NASA NTRS1995

Numerical simulation of supersonic flow using a new analytical bleed boundary condition

A new analytical bleed boundary condition is used to compute flowfields for a strong oblique shock wave/boundary layer interaction with a baseline and three bleed rates at a freestream Mach number of 2.47 with an 8 deg shock generator. The computational results are compared to experimental Pitot pressure profiles and wall static pressures through the interaction region. An algebraic turbulence model is employed for the bleed and baseline cases, and a one equation model is also used for the baseline case where the boundary layer is separated.

Harloff, G. J.↗
NASA NTRS1996

Experimental Investigation of the Effects of Acceleration on Heat Transfer in the Turbulent Boundary Layer

The objective of this research was to experimentally investigate the combined effects of freestream acceleration and surface roughness on heat transfer and fluid flow in the turbulent boundary layer. The experiments included a variety of flow conditions ranging from aerodynamically smooth to transitionally rough to fully rough boundary layers with accelerations ranging from moderate to moderately strong. The test surfaces used were a smooth-wall test surface and two rough-wall surfaces which were roughened with 1.27 mm diameter hemispheres spaced 2 and 4 base diameters apart in a staggered array. The measurements consisted of Stanton number distributions, mean temperature profiles, skin friction distributions, mean velocity profiles, turbulence intensity profiles, and Reynolds stress profiles. The Stanton numbers for the rough-wall experiments increased with acceleration. For aerodynamically smooth and transitionally rough boundary layers, the effect of roughness is not seen immediately at the beginning of the accelerated region as it is for fully rough boundary layers; however, as the boundery layer thins under acceleration, the surface becomes relatively rougher resulting in a sharp increase in Stanton number.

Chakroun, Walid M.↗
NASA NTRS1996

Twin Tail/Delta Wing Configuration Buffet Due to Unsteady Vortex Breakdown Flow

The buffet response of the twin-tail configuration of the F/A-18 aircraft; a multidisciplinary problem, is investigated using three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations. The second set is the coupled aeroelastic equations for bending and torsional twin-tail responses. The third set is the grid-displacement equations which are used to update the grid coordinates due to the tail deflections. The computational model consists of a 76 deg-swept back, sharp edged delta wing of aspect ratio of one and a swept-back F/A-18 twin-tails. The configuration is pitched at 32 deg angle of attack and the freestream Mach number and Reynolds number are 0.2 and 0.75 x 10(exp 6) respectively. The problem is solved for the initial flow conditions with the twin tail kept rigid. Next, the aeroelastic equations of the tails are turned on along with the grid-displacement equations to solve for the uncoupled bending and torsional tails response due to the unsteady loads produced by the vortex breakdown flow of the vortex cores of the delta wing. Two lateral locations of the twin tail are investigated. These locations are called the midspan and inboard locations.

Kandil, Osama A.↗
NASA NTRSDate not supplied

Bluntness and Supersaturation Effects on the Second Mode Instability in Mach 10 Flow

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 31-Inch Mach 10 Tunnel to investigate the impact of nosetip radius and freestream supersaturation on the development of the second mode instability. The model was instrumented with surface-mounted Kulite® and PCB® pressure transducers and thermocouples. Power spectral density plots demonstrate the anticipated trends of the second mode instability weakening and shifting to lower frequencies with increased bluntness. Heat transfer measurements suggest laminar flow over the bulk of the model for most testing conditions, with evidence of transition by the cone base for the sharpest nosetip (R = 0.15 mm) at the higher unit Reynolds numbers. The dynamic surface pressure and heat transfer measurements show that reducing the temperature of the freestream to a supersaturated state has a significant stabilizing effect on the model boundary layer. The surface measurements are observed to be highly dependent on the level of clustering in the freestream. Significant changes in surface pressure spectra due to total temperature reduction are first noted below T0= 948 K, while more substantial fluctuation reductions are found below T0= 810 K.

Hypersonics↗
NASA NTRS2000

Comparison of Predicted and Measured Turbine Vane Rough Surface Heat Transfer

The proposed paper compares predicted turbine vane heat transfer for a rough surface over a wide range of test conditions with experimental data. Predictions were made for the entire vane surface. However, measurements were made only over the suction surface of the vane, and the leading edge region of the pressure surface. Comparisons are shown for a wide range of test conditions. Inlet pressures varied between 3 and 15 psia, and exit Mach numbers ranged between 0.3 and 0.9. Thus, while a single roughened vane was used for the tests, the effective rougness,(k(sup +)), varied by more than a factor of ten. Results were obtained for freestream turbulence levels of 1 and 10%. Heat transfer predictions were obtained using the Navier-Stokes computer code RVCQ3D. Two turbulence models, suitable for rough surface analysis, are incorporated in this code. The Cebeci-Chang roughness model is part of the algebraic turbulence model. The k-omega turbulence model accounts for the effect of roughness in the application of the boundary condition. Roughness causes turbulent flow over the vane surface. Even after accounting for transition, surface roughness significantly increased heat transfer compared to a smooth surface. The k-omega results agreed better with the data than the Cebeci-Chang model. However, the low Reynolds number k-omega model did not accurately account for roughness when the freestream turbulence level was low. The high Reynolds number version of this model was more suitable when the freestream turbulence was low.

Boyle, R. J.↗
NASA NTRS1976

Computation of viscous transonic flow about a lifting airfoil

The viscous transonic flow about a stationary body in free air was numerically investigated. The geometry chosen was a symmetric NACA 64A010 airfoil at a freestream Mach number of 0.8, a Reynolds number of 4 million based on chord, and angles of attack of 0 and 2 degrees. These conditions were such that, at 2 degrees incidence unsteady periodic motion was calculated along the aft portion of the airfoil and in its wake. Although no unsteady measurements were made for the NACA 64A010 airfoil at these flow conditions, interpolated steady measurements of lift, drag, and surface static pressures compared favorably with corresponding computed time-averaged lift, drag, and surface static pressures.

Walitt, L.↗
NASA NTRS2015

Application of FLEET Velocimetry in the NASA Langley 0.3-meter Transonic Cryogenic Tunnel

Femtosecond laser electronic excitation and tagging (FLEET) velocimetry is demonstrated in a large-scale transonic cryogenic wind tunnel. Test conditions include total pressures, total temperatures, and Mach numbers ranging from 15 to 58 psia, 200 to 295 K, and 0.2 to 0.75, respectively. Freestream velocity measurements exhibit accuracies within 1 percent and precisions better than 1 m/s. The measured velocities adhere closely to isentropic flow theory over the domain of temperatures and pressures that were tested. Additional velocity measurements are made within the tunnel boundary layer; virtual trajectories traced out by the FLEET signal are indicative of the characteristic turbulent behavior in this region of the flow, where the unsteadiness increases demonstrably as the wall is approached. Mean velocities taken within the boundary layer are in agreement with theoretical velocity profiles, though the fluctuating velocities exhibit a greater deviation from theoretical predictions.

Burns, Ross A.↗
NASA NTRS2016

OH PLIF Visualization of a Premixed Ethylene-fueled Dual-Mode Scramjet Combustor

Hydroxyl radical (OH) planar induced laser fluorescence (PLIF) measurements have been performed in a small-scale scramjet combustor at the University of Virginia Aerospace Research Laboratory at nominal simulated Mach 5 enthalpy. OH lines were carefully chosen to have fluorescent signal that is independent of pressure and temperature but linear with mole fraction. The OH PLIF signal was imaged in planes orthogonal to and parallel to the freestream flow at different equivalence ratios. Flameout limits were tested and identified. Instantaneous planar images were recorded and analyzed to compare the results with width increased dual-pump enhanced coherent anti-Stokes Raman spectroscopy (WIDECARS) measurements in the same facility and large eddy simulation/Reynolds average Navier-Stokes (LES/RANS) numerical simulation. The flame angle was found to be approximately 10 degrees for several different conditions, which is in agreement with numerical predictions and measurements using WIDECARS. Finally, a comparison between NO PLIF non-combustion cases and OH PLIF combustion cases is provided: the comparison reveals that the dominant effect of flame propagation is freestream turbulence rather than heat release and concentration gradients.

Cantu, Luca M. L.↗
NASA NTRS1981

An experimental investigation of a large delta P settling chamber for a supersonic pilot quiet tunnel

The mean streamwise flow distributions and turbulence levels across the chamber were measured with a hot wire anemometer downstream of a series of porous Rigimesh plates which were shown to be an effective means of reducing the chamber acoustic disturbance levels due to upstream pipe and valve systems. Tests made with various types of flow conditioners downstream of the porous plates showed that a series of screens was the most effective means of achieving the objective of a uniform mean flow distribution with reduced vorticity levels downstream of the porous components. Frequency spectra obtained across the series of screens show that they reduce vorticity over a wide frequency range for several different initial upstream vorticity conditions. Improvements in the mechanical installation of the porous plates and damping screens and the use of porous plates with more uniform porosity should reduce the freestream velocity fluctuations to the minimum acoustic levels of about 0.5 percent.

Piatt, M.↗
NASA NTRS1990

Dynamics of the outgoing turbulent boundary layer in a Mach 5 unswept compression ramp interaction

Wall pressure fluctuations have been measured under the unsteady separation shock and on the ramp face in an unswept Mach 5 compression ramp interaction. The freestream Reynolds number was 51.0 x 10 to the 6th/m, and the incoming turbulent boundary layer developed on the tunnel floor under approximately adiabatic wall temperature conditions. Standard data-acquisition methods, as well as real-time and posttest conditional sampling techniques were used. The results show that the mean and rms pressure levels are strong functions of separation shock position. At all stations on the ramp, from the corner to where the pressure reaches the theoretical inviscid value, the pressure signals have two dominant components: a low frequency component characteristic of the global unsteadiness, which correlates with the separation shock motion, and a higher frequency component associated with turbulence. The former is the major contributor to the overall signal variance.

Gramann, Richard A.↗
NASA NTRS1992

A kappa-epsilon calculation of transitional boundary layers

A recently proposed kappa-epsilon model for low Reynolds number turbulent flows was modified by introducing a new damping function f(sub mu). The modified model is used to calculate the transitional boundary layer over a flat plate with different freestream turbulence levels. It is found that the model could mimic the transitional flow. However, the predicted transition is found to be sensitive to the initial conditions.

Yang, Z.↗