Search NASA⌕ Search

SEARCH · Search NASA

Results for “Function Estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Study to define low voltage and low temperature operating limits of the Pioneer 10/11 Meteoroid Detection Equipment (MDE) system

The Pioneer 10/11 meteoroid detection equipment (MDE) pressure cells were tested at liquid nitrogen (LN2) and liquid helium (LHe) temperatures with the excitation voltage controlled as a parameter. The cells failed by firing because of pressurizing gas condensation as the temperature was lowered from LN2 to LHe temperature and when raised from LHe temperature. A study was conducted to determine cell pressure as a function of temperature, and cell failure was estimated as a function of temperature and excitation voltage. The electronic system was also studied, and a profile of primary spacecraft voltage (nominally 28 Vdc) and temperature corresponding to electronic system failure was determined experimentally.

Parker, C. D.↗
NASA NTRS1976

Ocean color spectra measured off the Oregon coast - Characteristic vectors

The ocean color spectrum is defined as the ratio of the spectrum of light upwelled from the sea to the spectrum of light incident on the sea surface. Ocean color spectra, observed from an airplane flown over waters off Oregon, are analyzed. The original spectra are resolved into fifty-five wavelength bands, each 5 nm wide. The shapes of these spectra are parameterized by, and shown to be accurately recoverable from, their first four principal components. These components are the scalar projections of each spectrum on the first four characteristic vectors of the sample covariance matrix. Regression equations are found with which phytoplankton pigment concentration and water transparency may be estimated as linear functions of the principal components. Pigment concentration estimates thus obtained are imprecise. The poor fit is at least partly due to the inappropriateness of the linear regression model and the neglect of other optically important substances typically present in sea water.

Mueller, J. L.↗
NASA NTRS2011

Estimation of Time-Varying Pilot Model Parameters

Human control behavior is rarely completely stationary over time due to fatigue or loss of attention. In addition, there are many control tasks for which human operators need to adapt their control strategy to vehicle dynamics that vary in time. In previous studies on the identification of time-varying pilot control behavior wavelets were used to estimate the time-varying frequency response functions. However, the estimation of time-varying pilot model parameters was not considered. Estimating these parameters can be a valuable tool for the quantification of different aspects of human time-varying manual control. This paper presents two methods for the estimation of time-varying pilot model parameters, a two-step method using wavelets and a windowed maximum likelihood estimation method. The methods are evaluated using simulations of a closed-loop control task with time-varying pilot equalization and vehicle dynamics. Simulations are performed with and without remnant. Both methods give accurate results when no pilot remnant is present. The wavelet transform is very sensitive to measurement noise, resulting in inaccurate parameter estimates when considerable pilot remnant is present. Maximum likelihood estimation is less sensitive to pilot remnant, but cannot detect fast changes in pilot control behavior.

Zaal, Peter M. T.↗
NASA NTRS1989

Autonomous frequency domain identification: Theory and experiment

The analysis, design, and on-orbit tuning of robust controllers require more information about the plant than simply a nominal estimate of the plant transfer function. Information is also required concerning the uncertainty in the nominal estimate, or more generally, the identification of a model set within which the true plant is known to lie. The identification methodology that was developed and experimentally demonstrated makes use of a simple but useful characterization of the model uncertainty based on the output error. This is a characterization of the additive uncertainty in the plant model, which has found considerable use in many robust control analysis and synthesis techniques. The identification process is initiated by a stochastic input u which is applied to the plant p giving rise to the output. Spectral estimation (h = P sub uy/P sub uu) is used as an estimate of p and the model order is estimated using the produce moment matrix (PMM) method. A parametric model unit direction vector p is then determined by curve fitting the spectral estimate to a rational transfer function. The additive uncertainty delta sub m = p - unit direction vector p is then estimated by the cross spectral estimate delta = P sub ue/P sub uu where e = y - unit direction vectory y is the output error, and unit direction vector y = unit direction vector pu is the computed output of the parametric model subjected to the actual input u. The experimental results demonstrate the curve fitting algorithm produces the reduced-order plant model which minimizes the additive uncertainty. The nominal transfer function estimate unit direction vector p and the estimate delta of the additive uncertainty delta sub m are subsequently available to be used for optimization of robust controller performance and stability.

Yam, Yeung↗
NASA NTRS1988

Airborne in-situ spectral characterization and concentration estimates of fluorescent organics as a function of depth

The primary purpose of many in-situ airborne light scattering experiments in natural waters is to spectrally characterize the subsurface fluorescent organics and estimate their relative concentrations. This is often done by shining a laser beam into the water and monitoring its subsurface return signal. To do this with the proper interpretation, depth must be taken into account. If one disregards depth dependence when taking such estimates, both their spectral characteristics and their concentrations estimates can be rather ambiguous. A simple airborne lidar configuration is used to detect the subsurface return signal from a particular depth and wavelength. Underwater scatterometer were employed to show that in-situ subsurface organics are very sensitive to depth, but they also require the use of slow moving boats to cover large sample areas. Also, their very entry into the water disturbs the sample it is measuring. The method described is superior and simplest to any employed thus far.

Tittle, R. A.↗
NASA NTRS2014

Fuzzy Neuron: Method and Hardware Realization

This innovation represents a method by which single-to-multi-input, single-to-many-output system transfer functions can be estimated from input/output data sets. This innovation can be run in the background while a system is operating under other means (e.g., through human operator effort), or may be utilized offline using data sets created from observations of the estimated system. It utilizes a set of fuzzy membership functions spanning the input space for each input variable. Linear combiners associated with combinations of input membership functions are used to create the output(s) of the estimator. Coefficients are adjusted online through the use of learning algorithms.

Krasowski, Michael J.↗
NASA NTRS2005

ESTIMATION OF THE SPACE SHUTTLE ROLLOUT FORCING FUNCTION

The Space Shuttle Vehicle is assembled in the Vertical Assembly Building (VAB) at Kennedy Space Flight Center in Florida. The Vehicle is stacked on a Mobile Launch Platform (MLP) that weighs eight million pounds. A Crawler Transporter (CT) then carries the MLP and the stacked vehicle (12 million pounds total weight) to the launch complex located 5 miles away. This operation is performed at 0.9 mph resulting in a 4.5-hour transport. A recent test was performed to monitor the dynamic environment that was produced during rollout. It was found that the rollout is a harmonic-rich dynamic environment that was previously not understood. This paper will describe work that has been performed to estimate the forcing function that is produced in the transportation process. The rollout analysis team has determined that there are two families of harmonics of the drive train, which excite the system as a function of CT speed. There are also excitation sources, which are random or narrow-band in frequency and are not a function of CT speed. This presentation will discuss the application of the Sum of Weighted Accelerations Technique (SWAT) to further refine this understanding by estimating the forces and moments at the center-of-mass.

James, George H., III↗
NASA NTRS2010

Phase and Pupil Amplitude Recovery for JWST Space-Optics Control

This slide presentation reviews the phase and pupil amplitude recovery for the James Webb Space Telescope (JWST) Near Infrared Camera (NIRCam). It includes views of the Integrated Science Instrument Module (ISIM), the NIRCam, examples of Phase Retrieval Data, Ghost Irradiance, Pupil Amplitude Estimation, Amplitude Retrieval, Initial Plate Scale Estimation using the Modulation Transfer Function (MTF), Pupil Amplitude Estimation vs lambda, Pupil Amplitude Estimation vs. number of Images, Pupil Amplitude Estimation vs Rotation (clocking), and Typical Phase Retrieval Results Also included is information about the phase retrieval approach, Non-Linear Optimization (NLO) Optimized Diversity Functions, and Least Square Error vs. Starting Pupil Amplitude.

Dean, B. H.↗
NASA NTRS1984

Parameter estimation for the Euler-Bernoulli-beam

An approximation involving cubic spline functions for parameter estimation problems in the Euler-Bernoulli-beam equation (phrased as an optimization problem with respect to the parameters) is described and convergence is proved. The resulting algorithm was implemented and several of the test examples are documented. It is observed that the use of penalty terms in the cost functional can improve the rate of convergence.

Graif, E.↗
DOE OSTI2023

Photon production rate from Transverse-Longitudinal ( T – L) mesonic correlator on the lattice

Thermal photons from the QGP provide important information about the interaction among plasma constituents. The photon production rate from a thermally equilibrated system is proportional to the transverse spectral function ρ T (ω = |k → |,k → ). One can also calculate the photon production rate from the difference between ρ T (ω, k → ) (transverse) and ρ L (ω, k → ) (longitudinal) projections, as ρL vanishes on the photon point. Because the UV part of ρ T – ρ L is suppressed, the corresponding Euclidean correlator receives most of its contribution from the IR part. We calculate the T – L correlator on N f = 2 + 1 flavour HISQ configurations with m l = m s /5 at temperature of about 1.15T ρc (220 MeV). We have used two ansätze for the spectral function: 1) A polynomial connected to the UV region consistent with OPE expansion and 2) a hydro-inspired spectral function. We have also applied the Backus-Gilbert method to estimate the spectral function. All these different approaches are combined to estimate the photon production rate.

Bala, Dibyendu↗
NASA NTRS2012

Calculation of Coupled Vibroacoustics Response Estimates from a Library of Available Uncoupled Transfer Function Sets

The design and theoretical basis of a new database tool that quickly generates vibroacoustic response estimates using a library of transfer functions (TFs) is discussed. During the early stages of a launch vehicle development program, these response estimates can be used to provide vibration environment specification to hardware vendors. The tool accesses TFs from a database, combines the TFs, and multiplies these by input excitations to estimate vibration responses. The database is populated with two sets of uncoupled TFs; the first set representing vibration response of a bare panel, designated as H(sup s), and the second set representing the response of the free-free component equipment by itself, designated as H(sup c). For a particular configuration undergoing analysis, the appropriate H(sup s) and H(sup c) are selected and coupled to generate an integrated TF, designated as H(sup s +c). This integrated TF is then used with the appropriate input excitations to estimate vibration responses. This simple yet powerful tool enables a user to estimate vibration responses without directly using finite element models, so long as suitable H(sup s) and H(sup c) sets are defined in the database libraries. The paper discusses the preparation of the database tool and provides the assumptions and methodologies necessary to combine H(sup s) and H(sup c) sets into an integrated H(sup s + c). An experimental validation of the approach is also presented.

Smith, Andrew↗
NASA NTRS1981

Identifiability of unknown noise covariance matrices for some special cases of a linear, time-invariant, discrete-time dynamic system

Two off-line schemes are proposed for the identification of unknown noise covariance matrices Q and R of a discrete-time dynamic system. The first scheme is based on a maximum a posteriori cost function utilizing smoothed state estimates, while the second is based on a maximum likelihood cost function utilizing filtered state estimates. Sensitivity of the cost functions to Q and R is analyzed for the following cases: (1) single-input single-output systems; (2) multiinput single-output systems; and (3) single-input multioutput systems with a diagonal R. Identifiability criteria are presented for the cases considered and demonstrated by examples.

Tsang, W. L.↗
NASA NTRS2007

Space Radiation Risk Assessment for Future Lunar Missions

For lunar exploration mission design, radiation risk assessments require the understanding of future space radiation environments in support of resource management decisions, operational planning, and a go/no-go decision. The future GCR flux was estimated as a function of interplanetary deceleration potential, which was coupled with the estimated neutron monitor rate from the Climax monitor using a statistical model. A probability distribution function for solar particle event (SPE) occurrence was formed from proton fluence measurements of SPEs occurred during the past 5 solar cycles (19-23). Large proton SPEs identified from impulsive nitrate enhancements in polar ice for which the fluences are greater than 2 10(exp 9) protons/sq cm for energies greater than 30 MeV, were also combined to extend the probability calculation for high level of proton fluences. The probability with which any given proton fluence level of a SPE will be exceeded during a space mission of defined duration was then calculated. Analytic energy spectra of SPEs at different ranks of the integral fluences were constructed over broad energy ranges extending out to GeV, and representative exposure levels were analyzed at those fluences. For the development of an integrated strategy for radiation protection on lunar exploration missions, effective doses at various points inside a spacecraft were calculated with detailed geometry models representing proposed transfer vehicle and habitat concepts. Preliminary radiation risk assessments from SPE and GCR were compared for various configuration concepts of radiation shelter in exploratory-class spacecrafts.

Kim, Myung-Hee Y.↗
DOE OSTI2021

A selection function toolbox for subsets of astronomical catalogues

ABSTRACT Large catalogues are ubiquitous throughout astronomy, but most scientific analyses are carried out on smaller samples selected from these catalogues by chosen cuts on catalogued quantities. The selection function of that scientific sample – the probability that a star in the catalogue will satisfy these cuts and so make it into the sample – is thus unique to each scientific analysis. We have created a general framework that can flexibly estimate the selection function of a sample drawn from a catalogue in terms of position, magnitude and colour. Our method is unique in using the binomial likelihood and accounting for correlations in the selection function across position, magnitude, and colour using Gaussian processes and spherical harmonics. We have created a new open-source python package selectionfunctiontoolbox that implements this framework and used it to make three different estimates of the APOGEE DR16 red giant sample selection function, as a subset of 2MASS, with each estimate using an increasing amount of technical knowledge of the APOGEE targeting. In a companion paper, we applied our methodology to derive estimates of the astrometric and spectroscopic selection functions of Gaia EDR3. Our framework will make it trivial for astrophysicists to estimate the selection function that they should be using with the custom sample of stars that they have chosen to answer their scientific question.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1999

Noninvasive assessment of left atrial maximum dP/dt by a combination of transmitral and pulmonary venous flow

OBJECTIVES: The study assessed whether hemodynamic parameters of left atrial (LA) systolic function could be estimated noninvasively using Doppler echocardiography. BACKGROUND: Left atrial systolic function is an important aspect of cardiac function. Doppler echocardiography can measure changes in LA volume, but has not been shown to relate to hemodynamic parameters such as the maximal value of the first derivative of the pressure (LA dP/dt(max)). METHODS: Eighteen patients in sinus rhythm were studied immediately before and after open heart surgery using simultaneous LA pressure measurements and intraoperative transesophageal echocardiography. Left atrial pressure was measured with a micromanometer catheter, and LA dP/dt(max) during atrial contraction was obtained. Transmitral and pulmonary venous flow were recorded by pulsed Doppler echocardiography. Peak velocity, and mean acceleration and deceleration, and the time-velocity integral of each flow during atrial contraction was measured. The initial eight patients served as the study group to derive a multilinear regression equation to estimate LA dP/dt(max) from Doppler parameters, and the latter 10 patients served as the test group to validate the equation. A previously validated numeric model was used to confirm these results. RESULTS: In the study group, LA dP/dt(max) showed a linear relation with LA pressure before atrial contraction (r = 0.80, p < 0.005), confirming the presence of the Frank-Starling mechanism in the LA. Among transmitral flow parameters, mean acceleration showed the strongest correlation with LA dP/dt(max) (r = 0.78, p < 0.001). Among pulmonary venous flow parameters, no single parameter was sufficient to estimate LA dP/dt(max) with an r2 > 0.30. By stepwise and multiple linear regression analysis, LA dP/dt(max) was best described as follows: LA dP/dt(max) = 0.1 M-AC +/- 1.8 P-V - 4.1; r = 0.88, p < 0.0001, where M-AC is the mean acceleration of transmitral flow and P-V is the peak velocity of pulmonary venous flow during atrial contraction. This equation was tested in the latter 10 patients of the test group. Predicted and measured LA dP/dt(max) correlated well (r = 0.90, p < 0.0001). Numerical simulation verified that this relationship held across a wide range of atrial elastance, ventricular relaxation and systolic function, with LA dP/dt(max) predicted by the above equation with r = 0.94. CONCLUSIONS: A combination of transmitral and pulmonary venous flow parameters can provide a hemodynamic assessment of LA systolic function.

NASA Discipline Cardiopulmonary↗
NASA NTRS2016

Development of a Refined Space Vehicle Rollout Forcing Function

For several decades, American manned spaceflight vehicles and the associated launch platforms have been transported from final assembly to the launch pad via a pre-launch phase called rollout. The rollout environment is rich with forced harmonics and higher order effects can be used for extracting structural dynamics information. To enable this utilization, processing tools are needed to move from measured and analytical data to dynamic metrics such as transfer functions, mode shapes, modal frequencies, and damping. This paper covers the range of systems and tests that are available to estimate rollout forcing functions for the Space Launch System (SLS). The specific information covered in this paper includes: the different definitions of rollout forcing functions; the operational and developmental data sets that are available; the suite of analytical processes that are currently in-place or in-development; and the plans and future work underway to solve two immediate problems related to rollout forcing functions. Problem 1 involves estimating enforced accelerations to drive finite element models for developing design requirements for the SLS class of launch vehicles. Problem 2 involves processing rollout measured data in near real time to understand structural dynamics properties of a specific vehicle and the class to which it belongs.

James, George↗
DOE OSTI2017

Estimation of iodine nutrition and thyroid function status in late-gestation pregnant women in the United States: Development and application of a population-based pregnancy model

Previously, a deterministic biologically-based dose-response (BBDR) pregnancy model was developed to evaluate moderate thyroid axis disturbances with and without thyroid-active chemical exposure in a near-term pregnant woman and fetus. In the current study, the existing BBDR model was adapted to include a wider functional range of iodine nutrition, including more severe iodine deficiency conditions, and to incorporate empirically the effects of homeostatic mechanisms. The extended model was further developed into a population-based model and was constructed using a Monte Carlo-based probabilistic framework. In order to characterize total (T4) and free (fT4) thyroxine levels for a given iodine status at the population-level, the distribution of iodine intake for late-gestation pregnant women in the U.S was reconstructed using various reverse dosimetry methods and available biomonitoring data. The range of median (mean) iodine intake values resulting from three different methods of reverse dosimetry tested was 196.5–219.9 μg of iodine/day (228.2–392.9 μg of iodine/day). There was minimal variation in model-predicted maternal serum T4 and ft4 thyroxine levels from use of the three reconstructed distributions of iodine intake; the range of geometric mean for T4 and fT4, was 138–151.7 nmol/L and 7.9–8.7 pmol/L, respectively. The average value of the ratio of the 97.5th percentile to the 2.5th percentile equaled 3.1 and agreed well with similar estimates from recent observations in third-trimester pregnant women in the U.S. In addition, the reconstructed distributions of iodine intake allowed us to estimate nutrient inadequacy for late-gestation pregnant women in the U.S. via the probability approach. The prevalence of iodine inadequacy for third-trimester pregnant women in the U.S. was estimated to be between 21% and 44%. Taken together, the current work provides an improved tool for evaluating iodine nutritional status and the corresponding thyroid function status in pregnant women in the U.S. This model enables future assessments of the relevant risk of thyroid hormone level perturbations due to exposure to thyroid-active chemicals at the population-level. - Highlights: • A population-based thyroid function model for pregnant women was developed. • The model was used specifically study the late-gestation pregnant women in the U.S. • The prevalence of iodine inadequacy was estimated in the sub-population studied. • Developed model well predicts trimester-specific thyroid hormone reference ranges. • The model can be further used to study thyroid perturbations at a population level.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

A road map to cosmological parameter analysis with third-order shear statistics: III. Efficient estimation of third-order shear correlation functions and an application to the KiDS-1000 data

Context. Third-order lensing statistics contain a wealth of cosmological information that is not captured by second-order statistics. However, the computational effort it takes to estimate such statistics in forthcoming stage IV surveys is prohibitively expensive. Aims. We derive and validate an efficient estimation procedure for the three-point correlation function (3PCF) of polar fields such as weak lensing shear. We then use our approach to measure the shear 3PCF and the third-order aperture mass statistics on the KiDS-1000 survey. Methods We constructed an efficient estimator for third-order shear statistics that builds on the multipole decomposition of the 3PCF. We then validated our estimator on mock ellipticity catalogs obtained from N -body simulations. Finally, we applied our estimator to the KiDS-1000 data and presented a measurement of the third-order aperture statistics in a tomographic setup. Results. Our estimator provides a speedup of a factor of ∼100–1000 compared to the state-of-the-art estimation procedures. It is also able to provide accurate measurements for squeezed and folded triangle configurations without additional computational effort. We report a significant detection of tomographic third-order aperture mass statistics in the KiDS-1000 data (S/N = 6.69). Conclusions. Our estimator will make it computationally feasible to measure third-order shear statistics in forthcoming stage IV surveys. Furthermore, it can be used to construct empirical covariance matrices for such statistics.

Astronomy & Astrophysics↗