SEARCH · Search NASA

Results for “High angle of attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗

NASA NTRS1983

High angle-of-attack aerodynamics of a strake-canard-wing V/STOL fighter configuration

High angle-of-attack aerodynamic data are analyzed for a strake-canard-wing V/STOL fighter configuration. The configuration represents a twin-engine supersonic V/STOL fighter aircraft which uses four longitudinal thrust-augmenting ejectors to provide vertical lift. The data were obtained in tests of a 9.39 percent scale model of the configuration in the NASA Ames 12-Foot Pressure Wind Tunnel, at a Mach number of 0.2. Trimmed aerodynamic characteristics, longitudinal control power, longitudinal and lateral/directional stability, and effects of alternate strake and canard configurations are analyzed. The configuration could not be trimmed (power-off) above 12 deg angle of attack because of the limited pitch control power and the high degree of longitudinal instability (28 percent) at this Mach number. Aerodynamic center location was found to be controllable by varying strake size and canard location without significantly affecting lift and drag. These configuration variations had relatively little effect on the lateral/directional stability up to 10 deg angle of attack.

Durston, D. A.↗

NASA NTRS1982

An assessment of preliminary aerodynamic analysis methods for supersonic speeds including high angle-of-attack flow

The problems associated with predicting the aerodynamic loads for moderate supersonic Mach number, high angle-of-attack flows and for high supersonic Mach number flows are addressed. For these large disturbance-type flows, commonly used prediction methods based on linearized theory or on the tangent-wedge method are shown to be generally inadequate. For the preliminary analysis of aerodynamic shapes subjected to these type flows, two methods have recently been developed by combining features of the linearized theory and tangent-wedge method. These two new methods are discussed, and through extensive comparisons with experimental data, are shown to offer an improved prediction capability.

Pittman, J. L.↗

NASA NTRS1989

High angle-of-attack aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles-of-attack in the NASA Langley 14 by 22-Ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles-of-attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Vandam, C. P.↗

NASA NTRS1977

Assessment of existing analytic methods for prediction of high angle-of-attack loads on delta wings at supersonic speeds

An assessment of the applicability of four loading prediction methods to high angle-of-attack conditions for simplified wing-body configurations is provided. The methods are: The tangent wedge approximation, the linear theory methods of Middleton and Woodward, and a shock-fitting finite-difference technique. Estimates obtained by these methods were compared with experimental pressure data on delta wings to examine the effects of Mach number, camber, sweep angle, and angle of attack. Results indicate that all of the methods provided reasonable estimates at moderate angles of attack. At these moderate angles of attack, the methods of Middleton and Woodward provided good estimates at Mach numbers higher than those usually associated with linear theory. Only the finite-difference method provided reasonable load estimates at high angles of attack.

Landrum, E. J.↗

NASA NTRS1994

Flow analysis for the nacelle of an advanced ducted propeller at high angle-of-attack and at cruise with boundary layer control

An axisymmetric panel code and a three dimensional Navier-Stokes code (used as an inviscid Euler code) were verified for low speed, high angle of attack flow conditions. A three dimensional Navier-Stokes code (used as an inviscid code), and an axisymmetric Navier-Stokes code (used as both viscous and inviscid code) were also assessed for high Mach number cruise conditions. The boundary layer calculations were made by using the results from the panel code or Euler calculation. The panel method can predict the internal surface pressure distributions very well if no shock exists. However, only Euler and Navier-Stokes calculations can provide a good prediction of the surface static pressure distribution including the pressure rise across the shock. Because of the high CPU time required for a three dimensional Navier-Stokes calculation, only the axisymmetric Navier-Stokes calculation was considered at cruise conditions. The use of suction and tangential blowing boundary layer control to eliminate the flow separation on the internal surface was demonstrated for low free stream Mach number and high angle of attack cases. The calculation also shows that transition from laminar flow to turbulent flow on the external cowl surface can be delayed by using suction boundary layer control at cruise flow conditions. The results were compared with experimental data where possible.

Hwang, D. P.↗

NASA NTRS1982

High angle-of-attack characteristics of a forward-swept wing fighter configuration

The NASA-Langley Research Center is currently investigating the high angle-of-attack characteristics of a forward-swept wing fighter technology demonstrator in a cooperative program with the Defense Advanced Research Projects Agency. The program includes static and dynamic wind-tunnel force tests, free-flight model tests, spin-tunnel tests, and piloted simulation. Particular emphasis is placed on identifying the contributions of the forward-swept wing to the configuration aerodynamics at high angles of attack. Results are presented to illustrate the wing contributions in terms of aerodynamic stability, flow visualization, and observation of free-flight characteristics.

Grafton, S. B.↗

NASA NTRS1990

Preliminary results from a subsonic high angle-of-attack flush airdata sensing (HI-FADS) system: Design, calibration, and flight test evaluation

A nonintrusive high angle-of-attack flush airdata sensing (HI-FADS) system was installed and flight-tested on the F-18 high alpha research flight vehicle. The system is a matrix of 25 pressure orifices in concentric circles on the nose of the vehicle. The orifices determine angles of attack and sideslip, Mach number, and pressure altitude. Pressure was transmitted from the orifices to an electronically scanned pressure module by lines of pneumatic tubing. The HI-FADS system was calibrated and demonstrated using dutch roll flight maneuvers covering large Mach, angle-of-attack, and sideslip ranges. Reference airdata for system calibration were generated by a minimum variance estimation technique blending measurements from two wingtip airdata booms with inertial velocities, aircraft angular rates and attitudes, precision radar tracking, and meteorological analyses. The pressure orifice calibration was based on identifying empirical adjustments to modified Newtonian flow on a hemisphere. Calibration results are presented. Flight test results used all 25 orifices or used a subset of 9 orifices. Under moderate maneuvering conditions, the HI-FADS system gave excellent results over the entire subsonic Mach number range up to 55 deg angle of attack. The internal pneumatic frequency response of the system is accurate to beyond 10 Hz. Aerodynamic lags in the aircraft flow field caused some performance degradation during heavy maneuvering.

Whitmore, Stephen A.↗

NASA NTRS1983

Estimation of parameters involved in high angle-of-attack aerodynamic theory using spin flight test data

The difficulty in applying parameter estimation techniques to spinning airplanes is due in part to the unwieldy number of possible combinations of terms in the equations of motion, when the model structure is unknown. The combination of high angle of attack and high rotation rate results in aerodynamic functions which are quite complex. For wing dominated configurations it is advantageous to use aerodynamic theory to generate the model structure. In this way, the number of unknown parameters is reduced and the model accuracy may be increased. Under conditions for which the theory is inadequate, however, model accuracy may be reduced. Strip theory, for example, is incapable of predicting autorotative rolling moments indicated by wind tunnel tests at angles of attack exceeding 40 degrees. An improved aerodynamic theory would be necessary to successfully apply the technique advanced for such regions.

Taylor, L. W., Jr.↗

NASA NTRS1976

High angle-of-attack stability-and-control analysis

Methods of linear systems analysis were applied to mathematical models of aircraft flying at high angle of attack and maneuver rate. First order longitudinal and lateral directional coupling is obtained by linearizing the complete nonlinear equations of motion about a generalized (quasi steady) trim point. Open loop stability boundaries are defined using the linear dynamic equations, and pilot in the loop effects are presented. Stability augmentation structures for maneuvering flight conditions are shown to be defined readily using optimal control theory.

Stengel, R. F.↗

NASA NTRS1995

Prediction of Wind Tunnel Effects on the Installed F/A-18A Inlet Flow Field at High Angles-of-attack

NASA Lewis is currently engaged in a research effort as a team member of the High Alpha Technology Program (HATP) within NASA. This program utilizes a specially equipped F/A-18A, the High Alpha Research Vehicle (HARV), in an ambitious effort to improve the maneuverability of high performance military aircraft at low subsonic speed, high angle of attack conditions. The overall objective of the Lewis effort is to develop inlet technology that will ensure efficient airflow delivery to the engine during these maneuvers. One part of the Lewis approach utilizes computational fluid dynamics codes to predict the installed performance of inlets for these highly maneuverable aircraft. Wind tunnel tests were a major component of the Lewis program. Since the available wind tunnel was small (9 x 15 ft) as compared to the scale of the model of the F/A-18A (19.78 percent), there were questions about the capability to obtain useful inlet performance data. The blockage effects were expected to be very large. This report represents the results of an analysis to determine how the wind tunnel walls effect inlet performance at several angles of attack. The predictions for the external particle traces along the fuselage indicate the influence of the wind tunnel side wall under the model is greater at 30 deg angle of attack than at 50 deg angle of attack on the under Leading Edge Extension (LEX) vortex trajectory. The side wall above the model appears to have negligible influence on the under LEX vortex. This may be due to the LEX acting as 'shield' to the upper wall effects. As expected, the wind tunnel has a significant influence on the external forces. The lift and drag coefficients increase significantly for the wind tunnel model as compared to free stream conditions. The wind tunnel had a small effect on the inlet recovery and on inlet total pressure distortion patterns. The predicted recoveries for the wind tunnel model are within one percentage point of the model recoveries in free stream conditions.

Smith, Crawford F.↗

NASA NTRS1985

Experimental investigations on airfoils with different geometries in the domain of high angles of attack-flow separation

Wind tunnel tests were conducted on airfoil models in order to study the flow separation phenomena occurring for high angles of attack. Pressure distribution on wings of different geometries were measured. Results show that for three-dimensional airfoils layout and span lift play a role. Separation effects on airfoils with moderate extension are three-dimensional. The flow domains separated from the air foil must be treated three-dimensionally. The rolling-up of separated vortex layers increases with angle in intensity and induction effect and shows strong nonlinearities. Boundary layer material moves perpendicularly to the flow direction due to the pressure gradients at the airfoil; this has a stabilizing effect. The separation starts earlier with increasing pointed profiles.

Keil, J.↗

NASA NTRS1978

Theoretical and experimental aerodynamics of strake-wing interactions up to high angles-of-attack

This paper reports on an experimental investigation where the longitudinal aerodynamic characteristics were determined up to high angles-of-attack for configurations employing parametric variations in strake span and wing sweep and includes correlations with theory. The investigation included both component and complete configuration studies to provide information for the analysis of interaction effects. Comparisons between strake-wing and high canard-wing configurations demonstrate the strake-wing to develop higher lift coefficients than did the canard-wing due to enhanced interference effects. Correlations with theory demonstrate the suction analogy to be a useful method for estimating the effects of vortex flow aerodynamics on both component and total forces and moments.

Luckring, J. M.↗

NASA NTRS1960

Investigation of the Flow Over Simple Bodies at Mach Numbers of the Order of 20

It is shown that adequate means are available for calculating inviscid direct and induced pressures on simple axisymmetric bodies at zero angle of attack. The extent to which viscous effects can alter these predictions is indicated. It is also shown that inviscid induced pressures can significantly affect the stability of blunt, two-dimensional flat wings at low angles of attack. However, at high angles of attack, the inviscid induced pressure effects are negligible.

Henderson, Arthur, Jr.↗

NASA NTRS1984

A study of prediction methods for the high angle-of-attack aerodynamics of straight wings and fighter aircraft

Work is described dealing with two areas which are dominated by the nonlinear effects of vortex flows. The first area concerns the stall/spin characteristics of a general aviation wing with a modified leading edge. The second area concerns the high-angle-of-attack characteristics of high performance military aircraft. For each area, the governing phenomena are described as identified with the aid of existing experimental data. Existing analytical methods are reviewed, and the most promising method for each area used to perform some preliminary calculations. Based on these results, the strengths and weaknesses of the methods are defined, and research programs recommended to improve the methods as a result of better understanding of the flow mechanisms involved.

Mcmillan, O. J.↗

NASA NTRS1982

High angle-of-attack characteristics of three-surface fighter aircraft

As part of a research program aimed at providing information on the high angle-of-attack characteristics of three-surface fighter concepts incorporating a close-coupled canard, an investigation is being conducted on two specific configurations based on the F-18 and F-15 designs. The study configurations are being subjected to a wide range of tests including wind-tunnel tests, dynamic model tests, and piloted simulation. This paper summarizes the results obtained to date in this study. High-alpha results in the areas of static stability, damping, and control characteristics are reviewed and some of the more significant aerodynamic phenomena are identified.

Croom, M. A.↗

NASA NTRS1998

Spatial Characteristics of the Unsteady Differential Pressures on 16 percent F/A-18 Vertical Tails

Buffeting is an aeroelastic phenomenon which plagues high performance aircraft at high angles of attack. For the F/A-18 at high angles of attack, vortices emanating from wing/fuselage leading edge extensions burst, immersing the vertical tails in their turbulent wake. The resulting buffeting of the vertical tails is a concern from fatigue and inspection points of view. Previous flight and wind-tunnel investigations to determine the buffet loads on the tail did not provide a complete description of the spatial characteristics of the unsteady differential pressures. Consequently, the unsteady differential pressures were considered to be fully correlated in the analyses of buffet and buffeting. The use of fully correlated pressures in estimating the generalized aerodynamic forces for the analysis of buffeting yielded responses that exceeded those measured in flight and in the wind tunnel. To learn more about the spatial characteristics of the unsteady differential pressures, an available 16%, sting-mounted, F-18 wind-tunnel model was modified and tested in the Transonic Dynamics Tunnel (TDT) at the NASA Langley Research Center as part of the ACROBAT (Actively Controlled Response Of Buffet-Affected Tails) program. Surface pressures were measured at high angles of attack on flexible and rigid tails. Cross-correlation and cross-spectral analyses of the pressure time histories indicate that the unsteady differential pressures are not fully correlated. In fact, the unsteady differential pressure resemble a wave that travels along the tail. At constant angle of attack, the pressure correlation varies with flight speed.

Moses, Robert W.↗

NASA NTRS1982

Nacelle Aerodynamic and Inertial Loads (NAIL) project

A flight test survey of pressures measured on wing, pylon, and nacelle surfaces and of the operating loads on Boeing 747/Pratt & Whitney JT9D-7A nacelles was made to provide information on airflow patterns surrounding the propulsion system installations and to clarify processes responsible for inservice deterioration of fuel economy. Airloads at takeoff rotation were found to be larger than at any other normal service condition because of the combined effects of high angle of attack and high engine airflow. Inertial loads were smaller than previous estimates indicated. A procedure is given for estimating inlet airloads at low speeds and high angles of attack for any underwing high bypass ratio turbofan installation approximately resembling the one tested. Flight procedure modifications are suggested that may result in better fuel economy retention in service. Pressures were recorded on the core cowls and pylons of both engine installations and on adjacent wing surfaces for use in development of computer codes for analysis of installed propulsion system aerodynamic drag interference effects.

Source record↗