Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ice Formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Use of ERTS data for mapping Arctic sea ice

The author has identified the following significant results. Data from ERTS passes crossing the Bering Sea in early March have been correlated with ice observations collected in the Bering Sea Experiment (BESEX). On two flights of the NASA CV-990 aircraft, the ice conditions in the vicinity of St. Lawrence Island reported by the onboard observer are in close agreement with the ice conditions mapped from the corresponding ERTS imagery. The ice features identified in ERTS imagery and substantiated by the aerial observer include the locations of boundaries between areas consisting of mostly grey ice and of mostly first and multi-year ice, the existence of shearing leads, and the occurrence of open water with the associated development of stratus cloud streaks. The BESEX correlative ice formation verifies the potential of practical applications of ERTS data.

Barnes, J. C.↗

Evidence about hydrate and solid water in the Martian surface from the 1969 Mariner infrared spectrometer

Results of laboratory simulation studies and comparative computer analyses of infrared spectral data regarding the presence, distribution, and form of condensed-phase water in the Martian surface. The data were obtained with the aid of the Mariner 6 and 7 spacecraft which were equipped with infrared spectrometers recording the infrared spectrum from 1.9 to 14.4 microns. From the analysis of these data evidence is obtained which signifies some sort of compositional and/or particle size variability of the extent and nature of hydration. Changes are noted which could be due to ice thinly covering a small fraction of the planetary surface in particularly cold spots, possibly on partially shaded slopes. At southerly latitudes, the fraction so covered seems to increase as the polar cap edge is approached. It is therefore concluded that there is strong evidence of ice formation on the planetary surface at the edge of the polar cap.

Pimentel, G. C.↗

Applications of Seasat to the offshore oil, gas and mining industries

The NASA satellite Seasat-A (to be launched in 1978) has applications to the offshore oil, gas, and mining industries including: (1) improvements in weather and wave forecasting, (2) studies of past wind and wave statistics for planning design requirements, and (3) monitoring ice formation, breakup, and movement in arctic regions. The primary geographic areas which will be monitored by Seasat-A include: the Beaufort Sea, the Labrador Sea, the Gulf of Mexico, the U.S. east coast, West Africa, Equatorial East Pacific, the Gulf of Alaska, and the North Sea. Seasat-A instrumentation used in ocean monitoring consists of a radar altimeter, a radar scatterometer, a synthetic aperture radar, a microwave radiometer, and a visible and infrared radiometer. The future outlook of the Seasat program is planned in three phases: measurement feasibility demonstration (1978-1980), data accessibility/utility demonstration (1980-1983), and operational system demonstration (1983-1985).

Mourad, A. G.↗

Development progress, external tank for the Space Shuttle Main Propulsion System

Attention is given to the design parameters of the LH2/LO2 system in a description of the development of the external tank for the Space Shuttle Main Propulsion System (MPS). Design and functional changes for the MPS are reviewed, including: improvement of the vibroacoustic environment through the adaptation of a two-stage pilot to the existing basic valve design, a redesign of the GH2 vent line to accommodate increased deflections and loads, and the minimization of ice formation through slide joint insulation. The anti-geyser splash plate for the LO2 system is outlined in terms of fuel flow parameters under varying conditions of temperature and pressure, and test results for individual components are presented.

Norquist, L.↗

A Procedure for the Design of Air-Heated Ice-Prevention Systems

A procedure proposed for use in the design of air-heated systems for the continuous prevention of ice formation on airplane components is set forth. Required heat-transfer and air-pressure-loss equations are presented, and methods of selecting appropriate meteorological conditions for flight over specified geographical areas and for the calculation of water-drop-impingement characteristics are suggested. In order to facilitate the design, a simple electrical analogue was devised which solves the complex heat-transfer relationships existing in the thermal-system analysis. The analogue is described and an illustration of its application to design is given.

Neel, C. B.↗

Impingement of Water Droplets on an Ellipsoid with Fineness Ratio 5 in Axisymmetric Flow

The presence of radomes and instruments that are sensitive to water films or ice formations in the nose section of all-weather aircraft and missiles necessitates a knowledge of the droplet impingement characteristics of bodies of revolution. Because it is possible to approximate many of these bodies with an ellipsoid of revolution, droplet trajectories about an ellipsoid of revolution with a fineness ratio of 5 were computed for incompressible axisymmetric air flow. From the computed droplet trajectories, the following impingement characteristics of the ellipsoid surface were obtained and are presented in terms of dimensionless parameters: (1) total rate of water impingement, (2) extent of droplet impingement zone, (3) distribution of impinging water, and (4) local rate of water impingement.

Dorsch, Robert G.↗

Crater populations on Ganymede and Callisto

Voyager 1 observations reveal heavily cratered surfaces on Ganymede and Callisto which suggest that a period of heavy bombardment occurred in the outer solar system. The overall crater density on Ganymede indicates that the oldest regions began recording the observed crater population at a later time than Callisto. A diameter-dependent loss of craters from 10-40 km occurs on Ganymede and may be due to ice formation or the formation of arcuate troughs. Evidence is given which suggests that the population of bodies responsible for the period of late heavy bombardment in the inner solar system is very different from that responsible for the late heavy bombardment in the outer solar system. In addition, it is postulated that Ganymede and Callisto may principally record a population of bodies that never penetrated the inner solar system in numbers great enough to leave a recognizable signature.

Strom, R. G.↗

Structural concepts for future space transportation orbiters

Two structural concepts for a fully reusable STS orbiter are compared with respect to weight and the ability to satisfy structural goals. The cryogenic propellant tanks for both concepts use welded, blade-stiffened aluminum skins for leak-free containment and compatibility with LOX and LH2. The tanks are sized primarily by pressure, although some areas are sized by bending and fracture mechanics considerations. The tank concept is regarded as state-of-the-art, even though it requires a closed cell foam insulation with a dry air purge to prevent air liquefaction and ice formation. It is noted that the foam will require testing to verify its design life for use in the STS. One concept has nonintegral tanks suspended inside an insulated aluminum airframe and thrust structure. Here, a durable thermal protection system external insulation is mechanically attached to the airframe, allowing a buckled skin design. The other concept uses a novel structural arrangement consisting of a separate tank/thrust structure that supports a hot advanced-carbon-carbon aeroshell structure.

Taylor, A. H.↗

Documentation of ice shapes on the main rotor of a UH-1H helicopter in hover

A helicopter icing flight test program in the hover mode was conducted with a UH-1H aircraft. The ice formations were documented after landing by means of silicone rubber molds, stereo photography and outline tracings for later use in aerodynamic analyses. The documentation techniques are described and the results presented for a typical flight.

Lee, J. D.↗

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗

Documentation of ice shapes accreted on the main rotor of a UH-1H helicopter in level flight

Icing tests were conducted on a UH-1H helicopter in level flight behind a spray tanker near Duluth, Minnesota, during the winter of 1983-84 as part of the joint NASA/Army HIFT program. On landing, the ice formations on the main rotor were documented by casting a set of ten-inch molds on the blade using a Dow-Corning silicone rubber compound which was initially liquid at sub-freezing temperatures. Such documentation was accomplished for eight flights in which the temperature ranged from -11 C to -22 C and the in-cloud flight times ranged from 5 to 9 minutes.

Hanson, M. K.↗

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗

Antarctic Ocean polynyas

The spatial and temporal variability of sea ice concentrations derived from Nimbus-7 Scanning Multichannel Microwave Radiometer (SMMR) brightness temperatures are presented. Emphasis is on the continental shelf region of the Ross Sea during 1984, when supporting data were obtained from oceanographic stations and moored instruments. The effects of the large spring polynya in the Ross Sea on summer insolation, surface heat layer storage, and late autumn ice formation are described.

Jacobs, Stanley S.↗

A study of high-lift airfoils at high Reynolds numbers in the Langley low-turbulence pressure tunnel

An experimental study was conducted in the Langley Low Turbulence Pressure Tunnel to determine the effects of Reynolds number and Mach number on the two-dimensional aerodynamic performance of two supercritical type airfoils, one equipped with a conventional flap system and the other with an advanced high lift flap system. The conventional flap system consisted of a leading edge slat and a double slotted, trailing edge flap with a small chord vane and a large chord aft flap. The advanced flap system consisted of a leading edge slat and a double slotted, trailing edge flap with a large chord vane and a small chord aft flap. Both models were tested with all elements nested to form the cruise airfoil and with the leading edge slat and with a single or double slotted, trailing edge flap deflected to form the high lift airfoils. The experimental tests were conducted through a Reynolds number range from 2.8 to 20.9 x 1,000,000 and a Mach number range from 0.10 to 0.35. Lift and pitching moment data were obtained. Summaries of the test results obtained are presented and comparisons are made between the observed aerodynamic performance trends for both models. The results showing the effect of leading edge frost and glaze ice formation is given.

Morgan, Harry L., Jr.↗

Numerical study of the effects of icing on finite wing aerodynamics

The sectional and total aerodynamics load characteristics of moderate aspect ratio wings with and without simulated glaze leading-edge ice are studied using a three-dimensional, compressible Navier-Stokes solver. The wing has an untwisted, untapered planform shape with NACA 0012 airfoil section. The aspect ratio of the wing is chosen to be 5. Comparisons of computed surface pressures and sectional loads with experimental data for identical configurations are given. The abrupt decrease in the wing stall angle as a result of the leading edge ice formation is numerically demonstrated.

Kwon, Oh J.↗

Sea ice and oceanic processes on the Ross Sea continental shelf

The spatial and temporal variability of Antarctic sea ice concentrations on the Ross Sea continental shelf have been investigated in relation to oceanic and atmospheric forcing. Sea ice data were derived from Nimbus 7 scanning multichannel microwave radiometer (SMMR) brightness temperatures from 1979-1986. Ice cover over the shelf was persistently lower than above the adjacent deep ocean, averaging 86 percent during winter with little month-to-month of interannual variability. The large spring Ross Sea polynya on the western shelf results in a longer period of summer insolation, greater surface layer heat storage, and later ice formation in that region the following autumn.

Jacobs, S. S.↗

Simulation of iced wing aerodynamics

The sectional and total aerodynamic load characteristics of moderate aspect ratio wings with and without simulated glaze leading edge ice were studied both computationally, using a three dimensional, compressible Navier-Stokes solver, and experimentally. The wing has an untwisted, untapered planform shape with NACA 0012 airfoil section. The wing has an unswept and swept configuration with aspect ratios of 4.06 and 5.0. Comparisons of computed surface pressures and sectional loads with experimental data for identical configurations are given. The abrupt decrease in stall angle of attack for the wing, as a result of the leading edge ice formation, was demonstrated numerically and experimentally.

Potapczuk, M. G.↗

Prediction of ice accretion on a swept NACA 0012 airfoil and comparisons to flight test results

In the winter of 1989-90, an icing research flight project was conducted to obtain swept wing ice accretion data. Utilizing the NASA Lewis Research Center's DHC-6 DeHavilland Twin Otter aircraft, research flights were made into known icing conditions in Northeastern Ohio. The icing cloud environment and aircraft flight data were measured and recorded by an onboard data acquisition system. Upon entry into the icing environment, a 24 inch span, 15 inch chord NACA 0012 airfoil was extended from the aircraft and set to the desired sweep angle. After the growth of a well defined ice shape, the airfoil was retracted into the aircraft cabin for ice shape documentation. The ice accretions were recorded by ice tracings and photographs. Ice accretions were mostly of the glaze type and exhibited scalloping. The ice was accreted at sweep angles of 0, 30, and 45 degrees. A 3-D ice accretion prediction code was used to predict ice profiles for five selected flight test runs, which include sweep angle of zero, 30, and 45 degrees. The code's roughness input parameter was adjusted for best agreement. A simple procedure was added to the code to account for 3-D ice scalloping effects. The predicted ice profiles are compared to their respective flight test counterparts. This is the first attempt to predict ice profiles on swept wings with significant scalloped ice formations.

Reehorst, Andrew L.↗