Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inverse problems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Research of microwave scattering properties of snow fields

The results obtained in the research program of microwave scattering properties of snow fields are presented. Experimental results are presented showing backscatter dependence on frequency (5.8-8.0 GHz), angle of incidence (0-60 degrees), snow wetness (time of day), and frequency modulation (0-500 MHz). Theoretical studies are being made of the inverse scattering problem yielding some preliminary results concerning the determination of the dielectric constant of the snow layer. The experimental results lead to the following conclusions: snow layering affects backscatter, layer response is significant up to 45 degrees of incidence, wetness modifies snow layer effects, frequency modulation masks the layer response, and for the proper choice of probing frequency and for nominal snow depths, it appears to be possible to measure the effective dielectric constant and the corresponding water content of a snow pack.

Angelakos, D. J.↗
NASA NTRS1985

The Nagoya cosmic-ray muon spectrometer 3, part 4: Track reconstruction method

One of the greatest problems in measuring particle trajectories with an optical or visual detector system, is the reconstruction of trajectories in real space from their recorded images. In the Nagoya cosmic-ray muon spectrometer, muon tracks are detected by wide gap spark chambers and their images are recorded on the photographic film through an optical system of 10 mirrors and two cameras. For the spatial reconstruction, 42 parameters of the optical system should be known to determine the configuration of this system. It is almost impossible to measure this many parameters directly with usual techniques. In order to solve this problem, the inverse transformation method was applied. In this method, all the optical parameters are determined from the locations of fiducial marks in real space and the locations of their images on the photographic film by the non-linear least square fitting.

Shibata, S.↗
NASA NTRS1988

Analysis of a closed-kinematic chain robot manipulator

Presented are the research results from the research grant entitled: Active Control of Robot Manipulators, sponsored by the Goddard Space Flight Center (NASA) under grant number NAG-780. This report considers a class of robot manipulators based on the closed-kinematic chain mechanism (CKCM). This type of robot manipulators mainly consists of two platforms, one is stationary and the other moving, and they are coupled together through a number of in-parallel actuators. Using spatial geometry and homogeneous transformation, a closed-form solution is derived for the inverse kinematic problem of the six-degree-of-freedom manipulator, built to study robotic assembly in space. Iterative Newton Raphson method is employed to solve the forward kinematic problem. Finally, the equations of motion of the above manipulators are obtained by employing the Lagrangian method. Study of the manipulator dynamics is performed using computer simulation whose results show that the robot actuating forces are strongly dependent on the mass and centroid locations of the robot links.

Nguyen, Charles C.↗
NASA NTRS1989

Development of kinematic equations and determination of workspace of a 6 DOF end-effector with closed-kinematic chain mechanism

This report presents results from the research grant entitled Active Control of Robot Manipulators, funded by the Goddard Space Flight Center, under Grant NAG5-780, for the period July 1, 1988 to January 1, 1989. An analysis is presented of a 6 degree-of-freedom robot end-effector built to study telerobotic assembly of NASA hardware in space. Since the end-effector is required to perform high precision motion in a limited workspace, closed-kinematic mechanisms are chosen for its design. A closed-form solution is obtained for the inverse kinematic problem and an iterative procedure employing Newton-Raphson method is proposed to solve the forward kinematic problem. A study of the end-effector workspace results in a general procedure for the workspace determination based on link constraints. Computer simulation results are presented.

Nguyen, Charles C.↗
NASA NTRS1987

Spatially random models, estimation theory, and robot arm dynamics

Spatially random models provide an alternative to the more traditional deterministic models used to describe robot arm dynamics. These alternative models can be used to establish a relationship between the methodologies of estimation theory and robot dynamics. A new class of algorithms for many of the fundamental robotics problems of inverse and forward dynamics, inverse kinematics, etc. can be developed that use computations typical in estimation theory. The algorithms make extensive use of the difference equations of Kalman filtering and Bryson-Frazier smoothing to conduct spatial recursions. The spatially random models are very easy to describe and are based on the assumption that all of the inertial (D'Alembert) forces in the system are represented by a spatially distributed white-noise model. The models can also be used to generate numerically the composite multibody system inertia matrix. This is done without resorting to the more common methods of deterministic modeling involving Lagrangian dynamics, Newton-Euler equations, etc. These methods make substantial use of human knowledge in derivation and minipulation of equations of motion for complex mechanical systems.

Rodriguez, G.↗
NASA NTRS1987

Collision-free trajectory planning algorthm for manipulators

Collision-free trajectory planning for robotic manipulators is investigated. The task of the manipulator is to move its end-effector from one point to another point in an environment with polyhedral obstacles. An on-line algorithm is developed based on finding the required joint angles of the manipulator, according to goals with different priorities. The highest priority is to avoid collisions, the second priority is to plan the shortest path for the end effector, and the lowest priority is to minimize the joint velocity for smooth motion. The pseudo-inverse of the Jacobian matrix is applied for inverse kinematics. When a possible collision is detected, a constrained inverse kinematic problem is solved such that the collision is avoided. This algorithm can also be applied to a time-variant environment.

Pourboghrat, F.↗
NASA NTRS1989

Kinematics and dynamics of a six-degree-of-freedom robot manipulator with closed kinematic chain mechanism

This paper deals with a class of robot manipulators built based on the kinematic chain mechanism (CKCM). This class of CKCM manipulators consists of a fixed and a moving platform coupled together via a number of in-parallel actuators. A closed-form solution is derived for the inverse kinematic problem of a six-degre-of-freedom CKCM manipulator designed to study robotic applications in space. Iterative Newton-Raphson method is employed to solve the forward kinematic problem. Dynamics of the above manipulator is derived using the Lagrangian approach. Computer simulation of the dynamical equations shows that the actuating forces are strongly dependent on the mass and centroid of the robot links.

Nguyen, Charles C.↗
NASA NTRS1989

New results concerning the use of kinematically redundant manipulators in microgravity environments

This paper is concerned with the development of control strategies for kinematically redundant manipulators to be used in Space Station laboratories. These robots must be able to conduct experiments and manufacturing processes without disturbing the microgravity environment, and thus their dynamic base reactions/motions must be nearly eliminated. Redundant degrees of freedom permit the inverse kinematics problem to be solved in conjuction with the minimization of a cost function defined as a weighted sum of the base reactions. It is shown that the weights in the cost function should be used as an additional set of parameters in the minimization problem. The actual performance of the local optimal trajectory approach is demonstrated to be not as good as was previously reported.

Quinn, R. D.↗
NASA NTRS1989

On trajectory generation for flexible space crane: Inverse dynamics analysis by LATDYN

For future in-space construction facility, one or more space cranes capable of manipulating and positioning large and massive spacecraft components will be needed. Inverse dynamics was extensively studied as a basis for trajectory generation and control of robot manipulators. The focus here is on trajectory generation in the gross-motion phase of space crane operation. Inverse dynamics of the flexible crane body is much more complex and intricate as compared with rigid robot link. To model and solve the space crane's inverse dynamics problem, LATDYN program which employs a three-dimensional finite element formulation for the multibody truss-type structures will be used. The formulation is oriented toward a joint dominated structure which is suitable for the proposed space crane concept. To track a planned trajectory, procedures will be developed to obtain the actuation profile and dynamics envelope which are pertinent to the design and performance requirements of the space crane concept.

Chen, G.-S.↗
NASA NTRS1989

Kinematics, controls, and path planning results for a redundant manipulator

The inverse kinematics solution, a modal position control algorithm, and path planning results for a 7 degree of freedom manipulator are presented. The redundant arm consists of two links with shoulder and elbow joints and a spherical wrist. The inverse kinematics problem for tip position is solved and the redundant joint is identified. It is also shown that a locus of tip positions exists in which there are kinematic limitations on self-motion. A computationally simple modal position control algorithm has been developed which guarantees a nearly constant closed-loop dynamic response throughout the workspace. If all closed-loop poles are assigned to the same location, the algorithm can be implemented with very little computation. To further reduce the required computation, the modal gains are updated only at discrete time intervals. Criteria are developed for the frequency of these updates. For commanding manipulator movements, a 5th-order spline which minimizes jerk provides a smooth tip-space path. Schemes for deriving a corresponding joint-space trajectory are discussed. Modifying the trajectory to avoid joint torque saturation when a tip payload is added is also considered. Simulation results are presented.

Gretz, Bruce↗
NASA NTRS1989

A complete analytical solution for the inverse instantaneous kinematics of a spherical-revolute-spherical (7R) redundant manipulator

Using a method based upon resolving joint velocities using reciprocal screw quantities, compact analytical expressions are generated for the inverse solution of the joint rates of a seven revolute (spherical-revolute-spherical) manipulator. The method uses a sequential decomposition of screw coordinates to identify reciprocal screw quantities used in the resolution of a particular joint rate solution, and also to identify a Jacobian null-space basis used for the direct solution of optimal joint rates. The results of the screw decomposition are used to study special configurations of the manipulator, generating expressions for the inverse velocity solution for all non-singular configurations of the manipulator, and identifying singular configurations and their characteristics. Two functions are therefore served: a new general method for the solution of the inverse velocity problem is presented; and complete analytical expressions are derived for the resolution of the joint rates of a seven degree of freedom manipulator useful for telerobotic and industrial robotic application.

Podhorodeski, R. P.↗
NASA NTRS1989

Kinematics and control algorithm development and simulation for a redundant two-arm robotic manipulator system

An efficient approach to cartesian motion and force control of a 7 degree of freedom (DOF) manipulator is presented. It is based on extending the active stiffness controller to the 7 DOF case in general and use of an efficient version of the gradient projection technique for solving the inverse kinematics problem. Cooperative control is achieved through appropriate configuration of individual manipulator controllers. In addition, other aspects of trajectory generation using standard techniques are integrated into the controller. The method is then applied to a specific manipulator of interest (Robotics Research T-710). Simulation of the kinematics, dynamics, and control are provided in the context of several scenarios: one pertaining to a noncontact pick and place operation; one relating to contour following where contact is made between the manipulator and environment; and one pertaining to cooperative control.

Hennessey, Michael P.↗
NASA NTRS1989

Dynamic analysis of a 6 DOF CKCM robot end-effector for dual-arm telerobot systems

A dynamical analysis is performed for a six DOF robot end-effector built to study telerobotic service and maintenance of NASA hardwares in space. The design of the end-effector is based on the concept of closed-kinematic chain mechanism capable of performing precise motion in a small workspace. After presenting a closed-form solution for the inverse kinematic problem, the Lagrangian approach is used to derive a set of equations of motion for the end-effector where the generalized coordinates are selected to be the Cartesian coordinates. A computer simulation study shows that the centrifugal and Coriolis terms can be neglected for slow motion.

Nguyen, Charles C.↗
NASA NTRS1991

Fast Parallel Computation Of Manipulator Inverse Dynamics

Method for fast parallel computation of inverse dynamics problem, essential for real-time dynamic control and simulation of robot manipulators, undergoing development. Enables exploitation of high degree of parallelism and, achievement of significant computational efficiency, while minimizing various communication and synchronization overheads as well as complexity of required computer architecture. Universal real-time robotic controller and simulator (URRCS) consists of internal host processor and several SIMD processors with ring topology. Architecture modular and expandable: more SIMD processors added to match size of problem. Operate asynchronously and in MIMD fashion.

Fijany, Amir↗
NASA NTRS1990

A computational procedure for the dynamics of flexible beams within multibody systems

The dynamic analysis of three dimensional elastic beams which experience large rotational and large deformational motions are examined. The beam motion is modeled using an inertial reference for the translational displacements and a body-fixed reference for the rotational quantities. Finite strain rod theories are then defined in conjunction with the beam kinematic description which accounts for the effects of stretching, bending, torsion, and transverse shear deformations. A convected coordinate representation of the Cauchy stress tensor and a conjugate strain definition is introduced to model the beam deformation. To treat the beam dynamics, a two-stage modification of the central difference algorithm is presented to integrate the translational coordinates and the angular velocity vector. The angular orientation is then obtained from the application of an implicit integration algorithm to the Euler parameter/angular velocity kinematical relation. The combined developments of the objective internal force computation with the dynamic solution procedures result in the computational preservation of total energy for undamped systems. The present methodology is also extended to model the dynamics of deployment/retrieval of the flexible members. A moving spatial grid corresponding to the configuration of a deployed rigid beam is employed as a reference for the dynamic variables. A transient integration scheme which accurately accounts for the deforming spatial grid is derived from a space-time finite element discretization of a Hamiltonian variational statement. The computational results of this general deforming finite element beam formulation are compared to reported results for a planar inverse-spaghetti problem.

Downer, Janice Diane↗
NASA NTRS1991

A novel design for a hybrid space manipulator

Described are the structural design, kinematics, and characteristics of a robot manipulator for space applications and use as an articulate and powerful space shuttle manipulator. Hybrid manipulators are parallel-serial connection robots that give rise to a multitude of highly precise robot manipulators. These manipulators are modular and can be extended by additional modules over large distances. Every module has a hemispherical work space and collective modules give rise to highly dexterous symmetrical work space. Some basic designs and kinematic structures of these robot manipulators are discussed, the associated direct and inverse kinematics formulations are presented, and solutions to the inverse kinematic problem are obtained explicitly and elaborated upon. These robot manipulators are shown to have a strength-to-weight ratio that is many times larger than the value that is currently available with industrial or research manipulators. This is due to the fact that these hybrid manipulators are stress-compensated and have an ultralight weight, yet, they are extremely stiff due to the fact that force distribution in their structure is mostly axial. Actuation is prismatic and can be provided by ball screws for maximum precision.

Shahinpoor, MO↗
NASA NTRS1990

A high temperature thermal diffusivity determination procedure for solids and liquids

A new method for measuring the thermal diffusivity of materials at high temperatures is presented. The method is applicable to solids on Earth, and to liquids in the reduced gravity environment of space. It is especially suited to levitated liquid metals at elevated temperatures where thermal diffusivity data is not available. The method is applied in two parts, such that lumped analysis is valid in the first part, and Fourier's law of conduction is valid in the second. In both parts, the spherical specimen is assumed to have been heated to a desired temperature and cooled. An inverse conduction problem is then formulated and solved using Laplace transformation techniques. Using this solution, sample sizes, and experimentally obtained surface temperature history, the thermal diffusivity is determined by minimizing a function that satisifies the heat balance at the surface. Minimization is performed using a modified quasilinearization algorithm. Accuracy is very sensitive to error in the temperature data and increases with better curve fits to the temperature data. An error analysis is also performed, and the effect of errors in the various parameters on the evaluated thermal diffusivity is determined. An experimental study for solids on Earth is suggested, before development for implementation in space.

Bayazitoglu, Yildiz↗