Search NASA⌕ Search

SEARCH · Search NASA

Results for “JET ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Validation of Calibrated k–ε Model Parameters for Jet-in-Crossflow

Previous efforts determined a set of calibrated, optimal model parameter values for Reynolds-averaged Navier–Stokes (RANS) simulations of a compressible jet in crossflow (JIC) using a $k–ε$ turbulence model. These parameters were derived by comparing simulation results to particle image velocimetry (PIV) data of a complementary JIC experiment under a limited set of flow conditions. Here, a $k–ε$ model using both nominal and calibrated parameters is validated against PIV data acquired from a much wider variety of JIC cases, including a realistic flight vehicle. The results from the simulations using the calibrated model parameters showed considerable improvements over those using the nominal values, even for cases that were not used in the calibration procedure that defined the optimal parameters. This improvement is demonstrated using a number of quality metrics that test the spatial alignment of the jet core, the magnitudes of multiple flow variables, and the location and strengths of vortices in the counter-rotating vortex cores on the PIV planes. These results suggest that the calibrated parameters have applicability well outside the specific flow case used in defining them and that with the right model parameters, RANS solutions for the JIC can be improved significantly over those obtained from the nominal model.

42 ENGINEERING↗
DOE OSTI2021

Microcontroller-based aerosol jet printer control software

This software is used with a microcontroller to control an aerosol jet printing system. It was written for a 32-bit ARM microcontroller, providing greater processing speed and complexity relative to more conventional low-cost printer controllers. The microcontroller software was written using a real-time operating system (FreeRTOS), which simplifies parallel operation of multiple functions and further customization. It supports simultaneous motion planning, pulse generation for stepper motors, reading encoder feedback, communicating with multiple mass flow controllers, controlling solid state relays, handling a software-based emergency stop, and sending data to the client PC. The program is written in C and communicates with the client PC via USB connection. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. SAND2021-0436 O

Secor, EthanBenjamin↗
DOE OSTI2022

Model Validation Database for Fires Involving Fuels at Liquefied Natural Gas Facilities

This document provides a description of the model evaluation protocol (MEP) database for fires involving liquefied natural gas (LNG) and processing fuels at LNG facilities. The purpose of the MEP is to provide procedures regarding the assessment of a model's suitability to predict thermal exclusion zones resulting from a fire. The database includes measurements from pool fire, jet fire, and fireball experiments which are provided in a spreadsheet. Users are to enter model results into the spreadsheet which automatically generates statistical performance measures and graphical comparisons with the experimental data. The intent of this document is to provide a description of the experiments and of the procedure required to carry out the validation portion of the MEP. In addition, the statistical performance measures, measurements for comparisons, and parameter variation are provided.

03 NATURAL GAS↗
DOE OSTI2021

Probing the Chemical Kinetics of Minimalist Functional Group Gasoline Surrogates

We report surrogate mixtures are routinely used for understanding gasoline fuel combustion in engine simulations. The general trend in surrogate formulation has been to increase the number of fuel components in a mixture to better emulate real fuel properties. Recently, a new surrogate design strategy based on functional group analysis of real gasolines was proposed using a minimal number of species [minimalist functional group (MFG)-approach]. MFG surrogates (having just one or two components) could experimentally capture the ignition delay time (IDT), threshold sooting index, and smoke point of different gasoline fuels with hundreds of components. However, other combustion characteristics were not explored, and kinetic modeling of MFG surrogates was not reported. These aspects are addressed in this paper, where the combustion behavior of MFG surrogates for various gasolines was assessed by simulating IDT, jet-stirred reactor oxidation, and premixed laminar flame speeds using chemical kinetic modeling. MFG simulations were compared with experimental data of the real gasolines as well as with the more complex multicomponent (five to nine species) surrogates. This study reveals that binary MFG surrogate mixtures are capable of accurately simulating the combustion behavior of more complex gasoline fuels with hundreds of components.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Experimentally probing the extremes of droplet-on-demand printability via liquid metals

The liquid metal jetting droplet-on-demand technology provides many potential benefits to metal additive manufacturing. However, much is left to understand the operational margins to reliably create stable, satellite-free droplets. We elucidate these margins by experimentally probing the unexplored extremities of a recently proposed printability window based on the jet Weber (Wejet) and Ohnesorge (Z = 1/Oh) numbers. We generated stable droplets for 2 ≲ Wejet ≲ 4 for all tested Z = 339 to 2526—well beyond the bounds of any previously published printability window—suggesting that additional physics may be needed to understand droplet-on-demand in the high Z regime.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Numerical investigation of equivalence ratio effects on Flex-Fuel mixing controlled combustion enabled by prechamber ignition

There is interest in adapting renewable and low-carbon intensity fuels to heavy-duty engines to help displace criteria and greenhouse gas emissions associated with diesel combustion. Low-carbon fuels have inherently low cetane numbers and thus pose a significant challenge when considering direct substitution in diesel combustion systems. Use of an actively fueled prechamber as an ignition source to initiate mixing-controlled combustion (PC-MCC) of low-cetane fuels is becoming an attractive combustion mode to alleviate the identified reactivity deficit. This work focuses on the utilization of an active prechamber to facilitate diesel-like combustion of bioethanol-gasoline fuel blends in a heavy-duty engine. Recent results in this emerging technology suggest that ignition quality is uniquely coupled to prechamber equivalence ratio. In this numerical study, the fundamental implications of prechamber equivalence ratio on the ignition performance of direct injected fuels ranging from E10 to E100 are investigated using CONVERGE. Parametric studies of the prechamber operating strategy were assessed at diesel-like conditions to characterize the performance trends relative to a diesel baseline at the same boundary conditions. Simulation results indicate that PC-MCC is flex-fuel capable and achieves diesel-like ignition qualities and combustion processes for all fuels considered under stoichiometric and rich prechamber conditions. To characterize the equivalence ratio trends observed, a novel inflow boundary modeling technique was utilized to prescribe turbulent jets in place of the prechamber where selective speciation of the jet composition was conducted to isolate the ignition contributions of radical and reacting species in lean, stoichiometric, and rich jets. The inflow boundary modeling suggests that excess fuel and combustion intermediates present in jets produced from stratified and fuel-rich prechamber operation promotes higher jet temperatures and as such are superior ignition sources. Relative to a lean prechamber jet, the peak temperature of a reacting jet from a rich prechamber was up to 600 K hotter at fixed distances from the orifice exit. Furthermore, radicals also demonstrated an influence on the ignition process, but the combustion mode was identified to be thermally dominant.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Fire and Thermal Experiments in Support of the Model Evaluation Protocol for LNG Facility Fires

The motivation for the experiments reported here pertains to the siting of Liquefied Natural Gas (LNG) facilities which requires assessing the potential adverse radiant thermal impacts of accidental fires on the public. The objective is to obtain data on jet fires, pool fires, fireballs, and concrete walls that could serve as thermal barriers for model validation. The fuels tested include ethane, ethylene, propane, and isopentane.

42 ENGINEERING↗
DOE OSTI2021

A tidal disruption event coincident with a high-energy neutrino

Cosmic neutrinos provide a unique window into the otherwise hidden mechanism of particle acceleration in astrophysical objects. The IceCube Collaboration recently reported the likely association of one high-energy neutrino with a flare from the relativistic jet of an active galaxy pointed towards the Earth. However a combined analysis of many similar active galaxies revealed no excess from the broader population, leaving the vast majority of the cosmic neutrino flux unexplained. Here we present the likely association of a radio-emitting tidal disruption event, AT2019dsg, with a second high-energy neutrino. AT2019dsg was identified as part of our systematic search for optical counterparts to high-energy neutrinos with the Zwicky Transient Facility. The probability of finding any coincident radio-emitting tidal disruption event by chance is 0.5%, while the probability of finding one as bright in bolometric energy flux as AT2019dsg is 0.2%. Our electromagnetic observations can be explained through a multizone model, with radio analysis revealing a central engine, embedded in a UV photosphere, that powers an extended synchrotron-emitting outflow. This provides an ideal site for petaelectronvolt neutrino production. Assuming that the association is genuine, our observations suggest that tidal disruption events with mildly relativistic outflows contribute to the cosmic neutrino flux.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

LiDAR Measurements to Investigate Farm-to-Farm Interactions at the AWAKEN Experiment

The exponential growth of wind energy and the need to exploit wind resources over areas with higher energy potential have led to the construction of neighboring wind turbines and farms with relatively small separation distances. As a result, for specific wind and atmospheric conditions, the wakes generated by an upstream wind farm may affect wind resources available for a downstream wind farm resulting in detrimental impacts on energy harvesting and structural loads for the downwind wind turbines. Distances between neighboring wind farms are typically larger than those associated with intra-wind-farm wake interactions, generating cumulative wakes whose characteristics might differ from those predicted through classical engineering wake models. These phenomena are referred to as farm-to-farm interactions. A better understanding and characterization of farm-to-farm interactions is one of the science goals tackled by the ongoing American WAKE experimeNt (AWAKEN). The site under investigation for this field campaign comprises two large wind farms in northern Oklahoma, USA, which are spaced roughly 5km apart along the prevailing South-North wind direction. To investigate possible interactions between these two wind farms, the WindFluX mobile LiDAR station has been deployed mainly to perform volumetric scans over their gap region. In this paper, preliminary results from these LiDAR volumetric scans will be discussed, specifically for a case with multiple wind turbine wakes evolving during the occurrence of a low-level jet.

17 WIND ENERGY↗
DOE OSTI2024

Understanding the ignition process and flame structure of conventional and oxygenated fuels under engine relevant conditions – An optical study

Renewably generated synthetic fuels such as poly-oxymethylene ethers (OME) have a significant potential to effectively break the soot-NOX trade-off in compression ignition engines by using exhaust gas recirculation (EGR) to maintain low nitrogen oxide (NOX) emissions while maintaining good efficiency and simultaneously contributing to circular carbon economy. However, owing to the fundamental differences in properties of OME when compared to fossil-based diesel fuels, it is critical to fully understand its ignition and combustion phenomenology to take advantage of this fuel to its utmost potential. In this context, this work outlines the results of a systematic experimental study performed in a heavy-duty, single-cylinder, optical engine probing the spatial and temporal progression of fuel decomposition and ignition behavior of OME when compared to n-dodecane, a diesel-fuel surrogate. Thermodynamic analysis and optical diagnostics techniques including simultaneous HCHO-PLIF and OH-PLIF complemented by high-speed OH* chemiluminescence were employed along with parametric sweeps of intake temperature and EGR dilution rates. OME does not exhibit any observable low temperature heat release irrespective of the ambient oxygen concentration. Differences in the observed diffusive flame structure such as longer flame lift-off length, less pronounced combustion recession, faster premixed burn at ignition (“volumetric” ignition), non-sooting behavior suggest that the inherent presence of fuel-bound oxygen in OME can skew the air-fuel ratio (AFR) distribution within the jet thereby reducing the reliance of combustion on mixing and air entrainment. This leads to rapid late-cycle oxidation leading to shorter combustion duration and favorable combustion phasing. Results also suggest that OME exhibits relatively weak negative temperature coefficient (NTC) behavior, however, the OME fuel-decomposition kinetic-pathways produce significant concentration of HCHO, which might be erroneously interpreted as a product of cool-flames.

Air-fuel ratio↗
DOE OSTI2025

Hypersonic Jets of Detonation Products in the Hydrodynamic Collapse of Macroscopic Voids

Localizing the energetic output from detonation waves has been a long-standing challenge in applied detonation physics. Here, energy localization is achieved via machined millimeter scale voids in pressed samples of PBX 9501, an HMX (1,3,5,7-Tetranitro-1,3,5,7-tetrazocane)-based plastic bonded explosive. A main mechanism of energy localization in these systems, the formation of hydrodynamic jets of dense product gases, is characterized experimentally using a semicylindrical geometry in witness plate impact experiments and streak imaging of the jet propagating into the air. The distance at which the jet is optimally developed is identified and the supersonic flow structure in the vicinity of this feature is explored using hydrocode simulations. This analysis found that most of the kinetic energy of the hydrodynamic jet arises from pressure gradients induced by geometrically mediated squeeze flow lateral to the direction of detonation propagation. This work presents a new development in the control of energetic output from detonation waves and applications to detonation wave shaping are discussed.

42 ENGINEERING↗
DOE OSTI2020

In-situ monitoring for liquid metal jetting using a millimeter-wave impedance diagnostic

Abstract This article presents a millimeter-wave diagnostic for the in-situ monitoring of liquid metal jetting additive manufacturing systems. The diagnostic leverages a T-junction waveguide device to monitor impedance changes due to jetted metal droplets in real time. An analytical formulation for the time-domain T-junction operation is presented and supported with a quasi-static full-wave electromagnetic simulation model. The approach is evaluated experimentally with metallic spheres of known diameters ranging from 0.79 to 3.18 mm. It is then demonstrated in a custom drop-on-demand liquid metal jetting system where effective droplet diameters ranging from 0.8 to 1.6 mm are detected. Experimental results demonstrate that this approach can provide information about droplet size, timing, and motion by monitoring a single parameter, the reflection coefficient amplitude at the input port. These results show the promise of the impedance diagnostic as a reliable in-situ characterization method for metal droplets in an advanced manufacturing system.

42 ENGINEERING↗
DOE OSTI2023

Data for Construction of a Compact Array of Microplasma Jet Devices and Its Application for Random Mutagenesis of Rhodosporidium toruloides

A small and efficient DNA mutation-inducing machine was constructed with an array of microplasma jet devices (7 × 1) that can be operated at atmospheric pressure for microbial mutagenesis. Using this machine, we report disruption of a plasmid DNA and generation of mutants of an oleaginous yeast Rhodosporidium toruloides . Specifically, a compact-sized microplasma channel (25 × 20 × 2 mm3) capable of generating an electron density of greater than 1013 cm–3 was constructed to produce reactive species (N2*, N2+, O, OH, and Hα) under helium atmospheric conditions to induce DNA mutagenesis. The length of microplasma channels in the device played a critical role in augmenting both the volume of plasma and the concentration of reactive species. First, we confirmed that microplasma treatment can linearize a plasmid by creating nicks in vitro. Second, we treated R. toruloides cells with a jet device containing 7 microchannels for 5 min; 94.8% of the treated cells were killed, and 0.44% of surviving cells showed different colony colors as compared to their parental colony. Microplasma-based DNA mutation is energy-efficient and can be a safe alternative for inducing mutations compared to conventional methods using toxic mutagens. This compact and scalable device is amenable for industrial strain improvement involving large-scale mutagenesis.

Conversion↗
DOE OSTI2024

Development and Integration of a Stochastic Clad Damage Propagation Model into PRONGHORN-SC Subchannel Analysis Code

The failure of fuel pins in nuclear reactors is intrinsically stochastic. Typically, a combination of variation in manufacturing that affects the material characteristics and the fuel assembly dimensions, variation in operating conditions, such as local power, coolant flow rate, and irradiation induced changes in material properties lead to a large uncertainty in failure margin of the fuel pins. Failure, therefore, may occur in exceptional pins with adverse combinations of these variations. Upon a metal fuel pin (U-Pu-Zr/HT9) failure, depressurization of the fuel pin takes place by release of fission gas, liquid sodium bond, and potentially solid fuel particles or molten/eutectic fuel droplets through the hole in cladding. The effect of a fission gas jet on neighbor fuel pins and possible propagation of a clad damage during normal operation was studied experimentally in 1970s and it was found that the post-failure fission gas jet insulates the jet impingement area of the target fuel pin surface and could increase the target pin’s surface temperature by as much as 100 – 200 K during the failed pin depressurization. It was concluded that the effect should not lead to fuel pin failure propagation during normal operation. In accident scenarios of sodium and lead fast reactors such as Unprotected Loss-Of-Flow (ULOF) or Unprotected Transient Over Power (UTOP), the fuel pins can be subjected to higher clad temperatures and fuel pin pressures or fuel clad mechanical/chemical interaction where thermal creep margin becomes significantly lower compared to the normal operation conditions. Therefore, possible stochastic failure and the post-failure fission gas/fuel jet impingement could be critical in order to predict fuel pin failure propagation. Pin depressurization due to fission gas release may degrade the heat transfer by formation of a gas blanket on a neighboring pin surface, which is a local phenomenon, and by causing coolant flow deceleration and starvation, which could affect a surrounding region as well. Furthermore, the potential presence of solid fuel particles or molten fuel at the time of clad failure could boost post-failure jet induced degradation even further. The present study models the U-Pu-Zr/HT9 metal fuel pin failure and stochastic clad damage propagation by biased sampling based on a Cumulative Damage Fraction (CDF) type clad failure criterion and the normal distribution of fuel failure probability density as a function of logarithm of Cumulative Damage Fraction. In addition, the effect of post-failure fission gas jet on heat transfer degradation is modeled for the target pins. This model is called stochastic Clad Damage Propagation (CDAP). The CDAP model is now fully integrated into developmental version of PRONGHORN-SC subchannel analysis code, allowing for modeling local failures and its propagation potential. Section 2 describes the components of the CDAP models. Section 3 describes the model implementation to PRONGHORN-SC and input specifications. Section 4 describes the CDAP model validation coupled to PRONGHORN-SC.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Ducted fuel injection

Various technologies presented herein relate to heating a fuel and enhancing fuel and charge-gas mixing inside a combustion chamber to enable minimal, or no, generation of soot and/or other undesired emissions during ignition and subsequent combustion of the locally premixed mixtures. To enable sufficient mixing of the fuel and charge-gas, a jet of fuel can be directed to pass through a bore of a duct causing charge-gas to be drawn into the bore creating turbulence to mix the fuel and the drawn charge-gas. The duct can be heated to provision heating of the fuel and charge-gas mixture. The duct can be located proximate to an opening in a tip of a fuel injector. An ignition assist component can be located downstream of the duct to facilitate ignition of the fuel/charge-gas mixture.

42 ENGINEERING↗
DOE OSTI2021

Computational Characterization and Boundary Condition Models of a Jet Interaction Fluidic Oscillator

Fluidically oscillating jet actuators that generate sweeping jets when supplied with a pressurized fluid have been used to mitigate separation and reduce drag in a range of flow control applications. Their implementation in future flight vehicles would require fundamental understanding and accurate predictive techniques of the physics of their internal flow and jet formation. The present investigations focus on high-fidelity, time-accurate simulations to characterize the flow physics of the actuator in quiescent conditions. An important element of the present simulations is to demonstrate the ability of the computational fluid dynamics (CFD) solver to predict the jet characteristics and provide a basis for the development of improved boundary conditions (BC) without entirely resolving the geometrical features of the fluidic device. The CFD-predicted oscillation frequencies of the engendered jets were found to be in excellent agreement with experiments, even on two-dimensional meshes. The study revealed that three-dimensional simulations are required to capture some of the flow features of the sweeping jet such as the double peak in time-averaged velocity distributions downstream of the actuator’s orifice that were measured in experiments. Furthermore, several approaches for modeling the actuator were implemented and assessed in quiescent conditions. The evaluation of a boundary condition at the device throat, based on the phase-averaged flow variables, provides the basis for devising surface-based boundary conditions. The influence and necessity of including turbulent characteristics as part of the boundary conditions have also been identified.

42 ENGINEERING↗
DOE OSTI2022

Atomic Layer Thermopiles: Comprehensive static calibration, comparison and application in subsonic and supersonic flows

Here, this paper compares the calibration of different heat flux sensors in radiation- and convection-based sub- and supersonic operation. First, four heat flux sensors based on different principles: ALTP (Transverse Seebeck Effect), HFM-8E (differential-layer device), coaxial Thermocouple and a TG-2000 (circular-foil gage) are calibrated in a laser-based radiation setup. In a second step, all heat flux sensors are compared with a slug-calorimeter within a subsonic convection-dominated facility based on stagnation-point measurements of an impinging hot air jet. The obtained results indicate that a sensitivity transfer between a radiative calibrated sensor used in a mainly convective environment is not always possible and can lead to significant, systematic errors. Calibration in a subsonic shear flow with thermocouple readings demonstrate small divergence from the manufacturer provided sensitivity. Finally, supersonic testing with high frequency shock-boundary layer interactions highlight the need for ALTP rather than the conventional use of thermocouple arrays to resolve the high frequency phenomena associated with shock boundary layer interactions.

42 ENGINEERING↗
DOE OSTI2024

Temperature Distribution Within an Ignition Kernel Initiated by a Laser-Induced Plasma

The sizes of, and temperature distributions within, ignition kernels initiated by a Q-switched neodymium-doped yttrium aluminum garnet laser-induced plasma in an unconfined lean premixed hydrogen-air upward jet flow are investigated. The experiments involved a range of jet velocities and a range of deposited laser energies at a fixed height above the exit along the axis of a burner. The growth of, and the temperature distributions within, the ignition kernels, as affected by the size and the energy distribution of the laser-induced plasma, are monitored with an infrared camera. The initial ignition kernels’ areas are larger with higher laser pulse energies and remain unchanged up to [Formula: see text] and then increase by factors of up to 3 at [Formula: see text]. The change in the kernel area caused by the jet velocities is less than 1.5%. An increase of the bulk velocity by 190% decreases the ignition kernel temperature by 6%. This reduction in the ignition kernel temperatures is because of an increase in energy losses by a factor of 2 and decreases in heat releases by 2% at [Formula: see text] and by 11% at [Formula: see text]. The present contributions are: measurements of and insights into temperature distributions and kernel development rates during the laser-induced plasma ignition process at different deposited energies and flow velocities.

Engineering↗