Search NASA⌕ Search

SEARCH · Search NASA

Results for “JET stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Wind-Tunnel Investigation of Subsonic Longitudinal Aerodynamic Characteristics of a Tiltable-Wing Vertical-Take-Off-and-Landing Supersonic Bomber Configuration Including Turbojet Power Effects

Jet-powered model tests were made to determine the low-speed longitudinal aerodynamic characteristics of a vertical-take-off and-landing supersonic bomber configuration. The configuration has an unique engine-wing arrangement wherein six large turbojet engines (three on each side of the fuselage) are buried in a low-aspect-ratio wing which is tilted into the vertical plane for take-off. An essentially two-dimensional variable inlet, spanning the leading edge of each wing semispan, provides air for the engines. Jet flow conditions were simulated for a range of military (nonafterburner) and afterburner turbojet-powered flight at subsonic speeds. Three horizontal tails were tested at a station down-stream of the jet exit and at three heights above the jet axes. A semi-span model was used and test parameters covered wing-fuselage incidence angles from 0 deg to 15 deg, wing angles of attack from -4 deg to 36 deg, a variable range of horizontal-tail incidence angles, and some variations in power simulation conditions. Results show that, with all horizontal tails tested, there were large variations in static stability throughout the lift range. When the wing and fuselage were alined, the model was statically stable throughout the test range only with the largest tail tested (tail span of 1.25 wing span) and only when the tail was located in the low test position which placed the tail nearest to the undeflected jet. For transition flight conditions, none of the tail configurations provided satisfactory longitudinal stability or trim throughout the lift range. Jet flow was destabilizing for most of the test conditions, and varying the jet-exit flow conditions at a constant thrust coefficient had little effect on the stability of this model. Wing leading-edge simulation had some important effects on the longitudinal aerodynamic characteristics.

Thompson, Robert F.↗
NASA NTRS1987

Spatially growing disturbances in a high velocity ratio two-stream, coplanar jet

The influence of cold and heated secondary flow on the instability of a two-stream, coplanar jet having a 0.7 Mach number heated primary jet for a nominal fan to primary velocity ratio of 0.68 was investigated by means of inviscid linearized stability theory. The instability properties of spatially growing axisymmetric and first order azimuthal disturbances were studied. The instability characteristics of the two-stream jet with a velocity ratio of 0.68 are very different from those of a single stream jet, and a two-stream, coplanar jet having a 0.9 Mach number heated primary jet and a cold secondary jet for a fan to primary velocity ratio of 0.30. For X/D = 1 and in comparison to the case where the velocity ratio was 0.3, the presence of the fan stream with a velocity ratio of 0.68 enhanced the instability of the jet and increased the unstable frequency range. However, the axisymmetric mode (m = 0) and the first order azimuthal mode (m = 1) have similar spatial growth rates where the velocity ratio is 0.68 while for a velocity ratio of 0.3 the growth rate of the first order azimuthal mode (m = 1) is greater. Comparing the cold and hot secondary flow results showed that for a velocity ratio of 0.68 the growth rate is greater for cold.

Miles, J. H.↗
NASA NTRS1987

Spatially growing disturbances in a high velocity ratio two-stream, coplanar jet

The influence of cold and heated secondary flow on the instability of a two-stream, coplanar jet having a 0.7 Mach number heated primary jet for a nominal fan to primary velocity ratio of 0.68 was investigated by means of inviscid linearized stability theory. The instability properties of spatially growing axisymmetric and first order azimuthal disturbances were studied. The instability characteristics of the two-stream jet with a velocity ratio of 0.68 are very different from those of a single stream jet, and a two-stream, coplanar jet having a 0.9 Mach number heated primary jet and a cold secondary jet for a fan to primary velocity ratio of 0.30. For X/D = 1 and in comparison to the case where the velocity ratio was 0.3, the presence of the fan stream with a velocity ratio of 0.68 enhanced the instability of the jet and increased the unstable frequency range. However, the axisymmetric mode (m = 0) and the first order azimuthal mode (m = 1) have similar spatial growth rates where the velocity ratio is 0.68 while for a velocity ratio of 0.3 the growth rate of the first order azimuthal mode (m = 1) is greater. Comparing the cold and hot secondary flow results showed that for a velocity ratio of 0.68 the growth rate is greater for cold.

Miles, Jeffrey H.↗
NASA NTRS1988

Control Of Flexible Structures-2 (COFS-2) flight control, structure and gimbal system interaction study

The second Control Of Flexible Structures Flight Experiment (COFS-2) includes a long mast as in the first flight experiment, but with the Langley 15-m hoop column antenna attached via a gimbal system to the top of the mast. The mast is to be mounted in the Space Shuttle cargo bay. The servo-driven gimbal system could be used to point the antenna relative to the mast. The dynamic interaction of the Shuttle Orbiter/COFS-2 system with the Orbiter on-orbit Flight Control System (FCS) and the gimbal pointing control system has been studied using analysis and simulation. The Orbiter pointing requirements have been assessed for their impact on allowable free drift time for COFS experiments. Three fixed antenna configurations were investigated. Also simulated was Orbiter attitude control behavior with active vernier jets during antenna slewing. The effect of experiment mast dampers was included. Control system stability and performance and loads on various portions of the COFS-2 structure were investigated. The study indicates possible undesirable interaction between the Orbiter FCS and the flexible, articulated COFS-2 mast/antenna system, even when restricted to vernier reaction jets.

Fay, Stanley↗
NASA NTRS1981

Development and validation of the V/STOL aerodynamics and stability and control manual

A V/STOL Aerodynamics and Stability and Control Manual was developed to provide prediction methods which are applicable to a wide range of V/STOL configurations in hover and transition flight, in and out of ground effect. Propulsion-induced effects have been combined with unpowered aerodynamics in a buildup of total forces and moments for the jet-lift concept, so that total aerodynamics can be used to predict aircraft stability, control, and flying qualities characteristics. Results of longitudinal aerodynamic predictions have been compared with test data, and indicate that the methods are fast, inexpensive, and within the desired accuracy for the objective preliminary design stage.

Henderson, C.↗
NASA NTRS1977

NO-NO2 measurements in a methane-fueled swirl-stabilized combustor

Exhaust plane measurements of NO and NO2 emissions from a methane-fueled swirl-stabilized combustor are reported. Samples were obtained by water-cooled probes and analyzed by chemiluminescent and UV absorption techniques. The combustor consists of two confined concentric jets having swirl. The inner jet flows premixed fuel and air, the outer jet is air. Variable outer jet swirl allows operation with jets swirling either in the same or opposite directions (co- or counter-swirl), and the combustion is stabilized by the resulting recirculation zone formed on the combustor centerline. Swirl conditions strongly affect the NOx emissions because of the influence of swirl on the combustion process. In the co-swirl conditions, the inner flow reaches high temperatures, and the correspondingly high NOx emissions are primarily NO. Under counter-swirl conditions much lower values of total NO are found, and these emissions are almost entirely NO2. In this case vigorous mixing in the inter-jet shear layer leads to severe flame quenching and lower temperatures. Formation of NO2 is associated with quenching processes in the combustor and is thought to be formed via NO oxidation by HO2 free radicals.

Oven, M. J.↗
NASA NTRS1987

A theoretical analysis of the extinction limits of a methane-air opposed-jet diffusion flame

A theoretical analysis is described for a methane-air diffusion flame stabilized in the forward stagnation region of a porous metal cylinder in a forced convective flow. The analysis includes effects of radiative heat loss from the porous metal surface and finite rate kinetics but neglects the effects of gravity. The theoretically predicted extinction limits compare well with experimentally observed extinction limits from the literature. After the predicted limits compared well with the experimental limits, a parametric study of the effect of fuel surface emissivity and Lewis number was conducted with the numerical model. It was found that the computed blowoff limit is independent of radiative heat loss for high fuel blowing velocities but is a strong function of Lewis number. At low fuel blowing velocities, the extinction limit varies with both radiative heat loss and Lewis number. It is discovered, however, that even if thermal losses from the fuel surface are absent, the flame can extinguish at the fuel surface independently of Lewis number due to excessive reaction zone thinning.

Olson, S. L.↗
NASA NTRS1993

Environmental Effects on the Stability of Optical Fibers Used for Reference Frequency Distribution

The frequency Standards Laboratory at the Jet Propulsion Laboratory (JPL) is responsible for the generation and distribution of ultra-stabel reference frequencies in NASA's Deep Space Network (DSN).Certain assemblies and components of the Radio Science and VLBI systems are located in the cones of tracking antennas hundreds of meters from the Frequency and Timing Subsystem's frequency standards.

Environmental Effects↗
NASA NTRS1994

Thermal and Mechanical Stability of the WF/PC II Optical Alignment

The Wide Field/Planetary Camera (WF/PC), developed by the Jet Propulsion Laboratory (JPL) under contract to the National Aeronautics and Space Administration (NASA), is the principal science instrument on the Hubble Space Telescope (HST). The analytical predicted motion of the WF/PC II optical elements showed that the four mechanisms added to the WF/PC II optical train will be able to maintain instrument alignment through the entire range of environmental changes from alignment on earth to operation in space.

Wide↗
NASA NTRS1952

Amplitude of Supersonic Diffuser Flow Pulsations

A theoretical method for evaluating the stability characteristics and the amplitude and the frequency of pulsation of ram-jet engines without heat addition is presented herein. Experimental verification of the theoretical results are included where data were available. Theory and experiment show that the pulsation amplitude of a high mass-flow-ratio diffuser having no cone surface flow separation increases with decreasing mass flow. The theoretical trends for changes in amplitude, frequency, and mean-pressure recovery with changes in plenum-chamber volume were experimentally confirmed. For perforated convergent-divergent-type diffusers, a stability hysteresis loop was predicted on the pressure-recovery mass-flow-ratio curve. At a given mean mass-flow ratio, the higher.value of mean pressure recovery corresponded to oscillatory flow in the diffuser while the lower branch was stable. This hysteresis has been observed experimentally. The theory indicates that for a ram-jet engine of given diameter, the amplitude of pulsation of a supersonic diffuser is increased by decreasing the relative size of the plenum chamber with respect to the diffuser volume down to a critical value at which oscillations cease. In the region of these critical values, the stable mass-flow range of the diffuser may be increased either by decreasing the combustion chamber volume or by increasing the length of the diffuser.

Sterbentz, William H.↗
NASA NTRS1962

Jet Interference Effects on a Model of a Single-Engine Four Jet V/STOL Airplane at Mach Numbers from 0.60 to 1.00

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the interference from four exhaust jets on the aerodynamic characteristics of a model of a V/STOL airplane. The single- engine four-jet turbofan power plant of the airplane was simulated by inducing tunnel airflow through two large side inlets and injecting the decomposition products of hydrogen peroxide into the internal flow. The heated gas mixture was exhausted through four nozzles located on the sides of the fuselage under the wing, two near the wing leading edge and two forward of the trailing edge; the nozzles were deflected downward 1.5 deg and outward 5.0 deg to simulate cruise conditions. The wing of the model was a clipped delta with leading-edge sweep of 40 deg, aspect ratio of 3.06, taper ratio of 0.218, thickness-chord ratio of 0.09 at the root and 0.07 at the tip, and 10 deg negative dihedral. Aerodynamic and longitudinal stability coefficients were obtained for the model with the tail removed, and for horizontal-tail incidences of 0 deg and -5 deg. Data were obtained at Mach numbers from 0.60 to 1.00, angles of attack from 0 deg to 12 deg, and with jet total-pressure ratios up to 3.1. Jet operation generally caused a decrease in lift, an increase in pitching-moment coefficient, and a decrease in longitudinal stability at subsonic speeds. The jet interference effects on drag were detrimental at a Mach number of 0.60 and favorable at higher speeds for cruising-flight attitudes.

Schmeer, James W.↗
NASA NTRS2010

Effect of Turbulence Modeling on an Excited Jet

The flow dynamics in a high-speed jet are dominated by unsteady turbulent flow structures in the plume. Jet excitation seeks to control these flow structures through the natural instabilities present in the initial shear layer of the jet. Understanding and optimizing the excitation input, for jet noise reduction or plume mixing enhancement, requires many trials that may be done experimentally or computationally at a significant cost savings. Numerical simulations, which model various parts of the unsteady dynamics to reduce the computational expense of the simulation, must adequately capture the unsteady flow dynamics in the excited jet for the results are to be used. Four CFD methods are considered for use in an excited jet problem, including two turbulence models with an Unsteady Reynolds Averaged Navier-Stokes (URANS) solver, one Large Eddy Simulation (LES) solver, and one URANS/LES hybrid method. Each method is used to simulate a simplified excited jet and the results are evaluated based on the flow data, computation time, and numerical stability. The knowledge gained about the effect of turbulence modeling and CFD methods from these basic simulations will guide and assist future three-dimensional (3-D) simulations that will be used to understand and optimize a realistic excited jet for a particular application.

Brown, Clifford A.↗
NASA NTRS1993

Control of nonlinear systems with applications to constrained robots and spacecraft attitude stabilization

This thesis is organized in two parts. In Part 1, control systems described by a class of nonlinear differential and algebraic equations are introduced. A procedure for local stabilization based on a local state realization is developed. An alternative approach to local stabilization is developed based on a classical linearization of the nonlinear differential-algebraic equations. A theoretical framework is established for solving a tracking problem associated with the differential-algebraic system. First, a simple procedure is developed for the design of a feedback control law which ensures, at least locally, that the tracking error in the closed loop system lies within any given bound if the reference inputs are sufficiently slowly varying. Next, by imposing additional assumptions, a procedure is developed for the design of a feedback control law which ensures that the tracking error in the closed loop system approaches zero exponentially for reference inputs which are not necessarily slowly varying. The control design methodologies are used for simultaneous force and position control in constrained robot systems. The differential-algebraic equations are shown to characterize the slow dynamics of a certain nonlinear control system in nonstandard singularly perturbed form. In Part 2, the attitude stabilization (reorientation) of a rigid spacecraft using only two control torques is considered. First, the case of momentum wheel actuators is considered. The complete spacecraft dynamics are not controllable. However, the spacecraft dynamics are small time locally controllable in a reduced sense. The reduced spacecraft dynamics cannot be asymptotically stabilized using continuous feedback, but a discontinuous feedback control strategy is constructed. Next, the case of gas jet actuators is considered. If the uncontrolled principal axis is not an axis of symmetry, the complete spacecraft dynamics are small time locally controllable. However, the spacecraft attitude cannot be asymptotically stabilized using continuous feedback, but a discontinuous stabilizing feedback control strategy is constructed. If the uncontrolled principal axis is an axis of symmetry, the complete spacecraft dynamics cannot be stabilized. However, the spacecraft dynamics are small time locally controllable in a reduced sense. The reduced spacecraft dynamics cannot be asymptotically stabilized using continuous feedback, but again a discontinuous feedback control strategy is constructed.

Krishnan, Hariharan↗
NASA NTRS1978

Lean Combustion Limits of a Confined Premixed-Prevaporized Propane Jet

Lean blowout limits were reported for a premixed prevaporized propane jet issuing into a cylindrical combustor. A single hole in a flat plate was used as a flameholder. Flameholders with various hole diameters were used. Jet velocities were varied from 3 to 290 meters per second. The combustor cross sectional area was changed by using different quartz liners of 12.7 and 22.2 millimeters diameters. As a result the combustor Reynolds number varied from 1000 to 9000. Stability was achieved at laminar as well as turbulent conditions. Three zones of flame stability were observed. The blowout equivalence ratio varied with step size and the combustor and jet Reynolds numbers. The combustor inlet mixture temperature was 395 K, and the combustor pressure was 1 atmosphere.

Huck, K. L.↗
NASA NTRS1972

Supplementary active stabilization of nonrigid gravity gradient satellites

The use of active control for stability augmentation of passive gravity gradient satellites is investigated. The reaction jet method of control is the main interest. Satellite nonrigidity is emphasized. The reduction in the Hamiltonian H is used as a control criteria. The velocities, relative to local vertical, of the jets along their force axes are shown to be of fundamental significance. A basic control scheme which satisfies the H reduction criteria is developed. Each jet is fired when its velocity becomes appropriately large. The jet is de-energized when velocity reaches zero. Firing constraints to preclude orbit alteration may be needed. Control is continued until H has been minimized. This control policy is investigated using impulse and rectangular pulse models of the jet outputs.

Keat, J. E.↗
NASA NTRS1972

The effects of trajectory characteristics on scientific objectives for major planetary orbiters.

Outline of specific solutions in the areas of attitude control, interplanetary trajectory parameters, and orbital configurations of major planetary spacecraft. It is shown that inertia wheel supplementation to a three-axis, stabilized attitude control system will substantially reduce propellant weight and attitude jet firings, especially when considering three-year orbital lifetimes as well as interplanetary trip times of several years. Eight interplanetary trajectory parameters including the earth injection energy and the declination of the launch asymptote are shown for a 1980 earth launch mission to Jupiter. The effects of the interplanetary trajectory parameters on the deboost velocities and resulting orbits about Jupiter are summarized. Orbital mode and science interfaces are defined, and a celestial mechanics experiment independent of earth tracking is briefly outlined.

Paul, C. K.↗
NASA NTRS1976

Recent developments in NASA's Supersonic Cruise Aircraft Research /SCAR/ Program

The paper reviews the SCAR program with emphasis on research in the areas of propulsion system, structures and materials, aerodynamic performance, stratospheric emissions, and stability and controls. Specific results relate to multicycle engine progress, coannular jet noise relief, blended wing-body configuration progress, powered-lift progress, and progress in structural design methodology.

Mascitti, V. R.↗