Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lewis acidity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Light-Induced Al Plating on Si for Fabrication of an Ag-Free All-Al Solar Cell

Light-induced electroplating of Al as the front electrode on the n-type emitter of Si solar cells is proposed as a substitute for screen-printed Ag. The advantages and disadvantages of Al over Cu as the front electrode are discussed. The power of a green laser used for patterning of the SiN x antireflection coating is optimized. Conditions for removal of laser damage and contamination on the laser-patterned surface are identified. The effect of plating temperature and post-annealing temperature on Al morphology and resistivity are investigated. Several plating additives are explored to improve the morphology and resistivity of the Al film. Nicotinic acid produces the lowest resistivity of 3.1 μ Ω-cm. However, the lowest contact resistivity between light-induced Al and Si is 69 mΩ-cm 2 due to laser-induced damage to the emitter. The Al film spikes through the thin n-type emitter when annealed at 500 °C causing cell failure. The process reproducibility is also poor due to atmospheric moisture.

14 SOLAR ENERGY↗
DOE OSTI2022

Failure Modes of Platinized pn+-GaInP Photocathodes for Solar-Driven H2 Evolution

The long-term stability for the hydrogen-evolution reaction (HER) of homojunction pn+-Ga0.52In0.48P photocathodes (band gap = 1.8 eV) with an electrodeposited Pt catalyst (pn+-GaInP/Pt) has been systematically evaluated in both acidic and alkaline electrolytes. Electrode dissolution during chronoamperometry was correlated with changes over time in the current density-potential (J-E) behavior to reveal the underlying failure mechanism. Pristine pn+-GaInP/Pt photocathodes yielded an open-circuit photopotential (Eoc) as positive as >1.0 V vs the potential of the reversible hydrogen electrode (RHE) and a light-limited current density (Jph) of >12 mA cm-2 (1-sun illumination). However, Eoc and Jph gradually degraded at either pH 0 or pH 14. The performance degradation was attributed to three different failure modes: (1) gradual thinning of the n+-emitter layer due to GaInP dissolution in acid; (2) active corrosion of the underlying GaAs substrate at positive potentials causing delamination of the upper GaInP epilayers; and (3) direct GaAs/electrolyte contact compromising the operational stability of the device. This work reveals the importance of both substrate stability and structural integrity of integrated photoelectrodes toward stable solar fuel generation.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2021

New Insights Into Lignification via Network and Multi-Omics Analyses of Arogenate Dehydratase Knock-Out Mutants in Arabidopsis thaliana

Multiple Arabidopsis arogenate dehydratase (ADT) knock-out (KO) mutants, with phenotypes having variable lignin levels (up to circa 70% reduction), were studied to investigate how differential reductions in ADTs perturb its overall plant systems biology. Integrated "omics" analyses (metabolome, transcriptome, and proteome) of wild type (WT), single and multiple ADT KO lines were conducted. Transcriptome and proteome data were collapsed into gene ortholog (GO) data, with this allowing for enzymatic reaction and metabolome cross-comparisons to uncover dominant or likely metabolic biosynthesis reactions affected. Network analysis of enzymes-highly correlated to stem lignin levels-deduced the involvement of novel putative lignin related proteins or processes. These included those associated with ribosomes, the spliceosome, mRNA transport, aminoacyl tRNA biosynthesis, and phosphorylation. While prior work helped explain lignin biosynthesis regulation at the transcriptional level, our data here provide support for a new hypothesis that there are additional post-transcriptional and translational level processes that need to be considered. These findings are anticipated to lead to development of more accurate depictions of lignin/phenylpropanoid biosynthesis models in situ, with new protein targets identified for further biochemical analysis and/or plant bioengineering. Additionally, using KEGG defined functional categorization of proteomics and transcriptomics analyses, we detected significant changes to glucosinolate, a-linolenic acid, nitrogen, carotenoid, aromatic amino acid, phenylpropanoid, and photosynthesis-related metabolic pathways in ADT KO mutants. Metabolomics results also revealed that putative carotenoid and galactolipid levels were generally increased in amount, whereas many glucosinolates and phenylpropanoids (including flavonoids and lignans) were decreased in the KO mutants.

Arabidopsis, arogenate dehydratases, lignin, multi↗
DOE OSTI2020

Sequential Ammonia and Carbon Dioxide Adsorption on Pyrolyzed Biomass to Recover Waste Stream Nutrients

Untreated fecal waste in unsewered communities and reactive nitrogen (N) loading from wastewater and urine disposal are important environmental challenges. Through pyrolysis, untreated fecal waste can be converted into amine-rich carbon dioxide (CO 2 ) sorbents, the chemisorption of which tunes the surface chemistry toward ammonia (NH 3 ) uptake. We compared the N-loading potential within amine-rich pyrolyzed human solid waste through exposure to CO 2 followed by NH 3 with the N-loading potential on carboxyl-rich, pyrolyzed oxidized wood using sequential adsorption of isotopically labeled CO 2 and NH 3 . The total N content of pyrolyzed oxidized wood exposed once to NH3 was similar to native, pyrolyzed human solid waste (3.7% compared to 4.6%). However, sorption kinetics and spectroscopic evidence revealed distinct N forms between the two materials affecting subsequent CO 2 and NH 3 uptake. Tertiary amines comprised 70% of N in pyrolyzed waste, compared to only 53% in pyrolyzed oxidized wood. The high heat of adsorption of CO 2 on pyrolyzed human solid waste (50 kJ mol-1) at low concentrations (0.05 mmol CO 2 g -1 ) was indicative of CO 2 reactivity with tertiary amines, consistent with the formation of carbamic acid (Figure S1). Conversely, after exposure to NH 3 , pyrolyzed oxidized wood chemisorbed CO 2 at much higher concentrations (0.7 mmol CO 2 g-1), pointing to primary amines as the active functional moieties. Adsorption kinetics of pyrolyzed oxidized wood revealed continued, albeit diminishing NH 3 uptake with each consecutive CO 2 treatment, averaging 5.9 mmol NH 3 g -1 for the first NH 3 exposure event, and still 3.5 and 2.9 mmol NH 3 g -1 for the second and third. Penetration of 15 NH 3 and 13 CO 2 measured by NanoSIMS reached over 7 µm deep into both materials, explaining the large NH 3 capture. The significantly lower NH 3 adsorption compared to pyrolyzed oxidized wood may be a result of potassium (K) carbonate precipitation precluding a Lewis base interaction between NH 3 and chemisorbed CO 2 , suggested by a 2-fold increase in surface K concentrations after exposure of pyrolyzed human solid waste to CO 2 +NH 3 detected by XPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Characterization of Interactions between CTX-M-15 and Clavulanic Acid, Desfuroylceftiofur, Ceftiofur, Ampicillin, and Nitrocefin

Cefotaximase-Munich (CTX-M) extended-spectrum beta-lactamases (ESBLs) are commonly associated with Gram-negative, hospital-acquired infections worldwide. Several beta-lactamase inhibitors, such as clavulanate, are used to inhibit the activity of these enzymes. To understand the mechanism of CTX-M-15 activity, we have determined the crystal structures of CTX-M-15 in complex with two specific classes of beta-lactam compounds, desfuroylceftiofur (DFC) and ampicillin, and an inhibitor, clavulanic acid. The crystal structures revealed that Ser70 and five other residues (Lys73, Tyr105, Glu166, Ser130, and Ser237) participate in catalysis and binding of those compounds. Based on analysis of steady-state kinetics, thermodynamic data, and molecular docking to both wild-type and S70A mutant structures, we determined that CTX-M-15 has a similar affinity for all beta-lactam compounds (ceftiofur, nitrocefin, DFC, and ampicillin), but with lower affinity for clavulanic acid. A catalytic mechanism for tested β-lactams and two-step inhibition mechanism of clavulanic acid were proposed. CTX-M-15 showed a higher activity toward DFC and nitrocefin, but significantly lower activity toward ampicillin and ceftiofur. The interaction between CTX-M-15 and both ampicillin and ceftiofur displayed a higher entropic but lower enthalpic effect, compared with DFC and nitrocefin. DFC, a metabolite of ceftiofur, displayed lower entropy and higher enthalpy than ceftiofur. This finding suggests that compounds containing amine moiety (e.g., ampicillin) and the furfural moiety (e.g., ceftiofur) could hinder the hydrolytic activity of CTX-M-15.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Investigating the Influence of Hexanuclear Clusters in Isostructural Metal–Organic Frameworks on Toxic Gas Adsorption

The efficient capture of toxic gases, such as ammonia (NH 3 ) and sulfur dioxide (SO 2 ), can protect the general population and mitigate widespread air pollution. Metal–organic frameworks (MOFs) comprise a tunable class of adsorbents with high surface areas that can meet this challenge by selectively capturing these gases at low concentrations. In this work, we explored how modifying the metal ions in the node of an isostructural MOF series from a transition metal to a lanthanide or actinide influences the electronic environment of the node-based active site. Next, we investigated the adsorption properties of each MOF toward the relatively basic NH 3 and relatively acidic SO 2 gases. Within the NU-907 family of MOFs, we found that Zr 6 -NU-907 exhibits the best uptake toward NH 3 at low pressures, while Th 6 -NU-907 demonstrates the best low-pressure performance for SO 2 adsorption. Here, tracking the infrared (IR) stretching frequency of the node-based μ 3 -OH groups provides insights into the electronegativity of the metal ion and suggests that the most electronegative metal ion (Zr) affords the node with the best NH 3 uptake at low pressures. In contrast, the Th 6 node contains additional coordinated water groups relative to the other M 6 nodes, which appears to yield the MOF with the greatest affinity for SO 2 uptake that occurs predominately through reversible physisorption interactions. Finally, in situ NH3 IR spectroscopic studies indicate that both NH 4 + and Lewis-bound NH 3 species form during adsorption. Combined, these results suggest that tuning the electronic properties and structure of the node-based active site in an MOF presents a viable strategy to change the affinity of an MOF toward toxic gases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Data for "Decompartmentalization of the yeast mitochondrial metabolism to improve chemical production in Issatchenkia orientalis "

Microbial production of chemicals may suffer from inadequate cofactor provision, a challenge further exacerbated in yeasts due to compartmentalized cofactor metabolism. Here, we perform cofactor engineering through the decompartmentalization of mitochondrial metabolism to improve succinic acid (SA) production in Issatchenkia orientalis . We localize the reducing equivalents of mitochondrial NADH to the cytosol through cytosolic expression of its pyruvate dehydrogenase (PDH) complex and couple a reductive tricarboxylic acid pathway with a glyoxylate shunt, partially bypassing an NADH-dependent malate dehydrogenase to conserve NADH. Cytosolic SA production reaches a titer of 104 g/L and a yield of 0.85 g/g glucose, surpassing the yield of 0.66 g/g glucose constrained by cytosolic NADH availability. Additionally, expressing cytosolic PDH, we expand our I. orientalis platform to enhance acetyl-CoA-derived citramalic acid and triacetic acid lactone production by 1.22- and 4.35-fold, respectively. Our work establishes I. orientalis as a versatile platform to produce markedly reduced and acetyl-CoA-derived chemicals.

bioproducts↗
DOE OSTI2025

Nb 2 O 5 Protection Layers for Hydrogen Evolution by p-InP Photocathodes in Acidic Electrolytes

Coatings of HfO 2 , Ta 2 O 5 , TiO 2 , and Nb 2 O 5 were evaluated as protection layers for p-InP photocathodes in aqueous acidic electrolytes. Each candidate protection layer was characterized based on interfacial conduction of photogenerated electrons, the thermodynamic and kinetic stability of the overlayer over the relevant potential and pH range for cathodic fuel-forming half-reactions, and inhibition of the primary anodic and/or chemical dissolution processes that limit electrode stability. The conduction of photogenerated electrons and inhibition of anodic oxidation was evaluated using V 3+ / 2+ in 5.0 M HCl(aq) as a one-electron redox couple with a potential close to that of hydrogen evolution in acidic media. Failure modes due to cathodic plating of metal, as well as anodic dissolution and chemical dissolution processes, were evaluated for photocathodes made from etched p-InP, platinized p-InP, and p-InP photoelectrodes that had been coated with the various oxide films and then platinized for use in photoelectrochemical hydrogen evolution in acidic aqueous electrolytes. Nb 2 O 5 best met all of the criteria, contrasting with TiO 2 , which is thermodynamically and kinetically unstable in acid over the potential range relevant for the hydrogen evolution and/or CO 2 reduction electrochemical half-reactions. Furthermore, these protocols should be useful for other materials and semiconductors to determine the effectiveness of protection layers for photocathodes.

Electrodes↗
DOE OSTI2019

Approaches to investigate the role of chelation in the corrosivity of biomass-derived oils

The need to provide the U.S. market with a renewable liquid fuel energy source from a non-food feedstock stream has gained considerable traction due to benefits such as improved energy efficiency, reduced environmental impacts, and enhanced national security. Practical achievement of these goals via biomass and bio-waste utilization involves production of liquid intermediates containing corrosive, reactive species like carboxylic acids, ketones, aldehydes, and hydroxyaldehydes. Such mixtures challenge materials of containment, processing, and transport. It is widely recognized that the smaller organic acids, such as acetic and formic, are corrosive and can remove protective surface oxides on alloys used in bio-oil processing infrastructure, and ketones can swell sealing polymers. However, literature shows, and findings herein confirm, larger carboxylic acids and bidentate alcohols are present. This highlights the potential for synergistic, detrimental effects of constituents in bio-oil corrosion, including direct reactivity of small acids compounded with the possibility of mobilization of protective metal oxide layers via chelation by larger acids and oxygenates. The question of whether species beyond small acids can significantly contribute to corrosion requires analytical approaches previously not applied to bio-oil corrosion studies and certainly not previously applied corroboratively. As such, this work introduces a combination of optical, mass spectral, and electrochemical impedance spectroscopies with an incubation approach to study metal mobilization, to facilitate elucidating chelation's role in bio-oil corrosive pathways. To enable systematic study of these oxygenates' material compatibility individually and in combination, a model matrix of bio-oil constituents was also developed based on identification of key components of real bio-oils.

09 BIOMASS FUELS↗
DOE OSTI2026

Aqueous ionic liquid–mediated depolymerization of textile waste

Textile waste, dominated by polyester-cotton blends, largely evades recycling and ends up in landfills or incinerators. Here, we demonstrate an aqueous ionic liquid–mediated route for selective depolymerization of textile waste, including polyester and polycotton (polyester/cotton blend). Using aqueous cholinium lysinate ([Ch][Lys]), we depolymerized poly(ethylene terephthalate) (PET) textiles with over 95 % terephthalic acid (TPA) yields, comparable to virgin PET resin. Notably, colored fabrics showed no inhibitory effect from dyes. While protic ionic liquids such as ethanolammonium acetate showed limited efficiency, their precursor amine enabled near-complete PET conversion—ethanolamine promoted aminolysis with byproduct formation whereas butylamine achieved higher TPA recovery through combined hydrolysis and aminolysis. Importantly, polycotton blends achieved complete PET depolymerization with TPA yield above 85 % and preserved cotton. These results establish aqueous ionic liquids as efficient, selective agents for deconstructing polyester in blended textiles, offering flexible product and ionic liquid management pathways toward scalable and facile textile recycling.

Amines↗
DOE OSTI2022

Steric and Lewis Basicity Influence of the Second Coordination Sphere on Electrocatalytic CO 2 Reduction by Manganese Bipyridyl Complexes

This study aims to provide a greater insight into the balance between steric (bpy vs (Ph) 2 bpy vs mes 2 bpy ligands) and Lewis basic ((Ph) 2 bpy vs (MeOPh) 2 bpy vs (MeSPh) 2 bpy ligands) influence on the efficiencies of the protonation-first vs reduction-first CO 2 reduction mechanisms with [Mn I (R 2 bpy)(CO) 3 (CH 3 CN)] + precatalysts, and on their respective transition-state geometries/energies for rate-determining C–OH bond cleavage toward CO evolution. The presence of only modest steric bulk at the 6,6'-diphenyl-2,2'-bipyridyl ((Ph) 2 bpy) ligand has here allowed unique insight into the mechanism of catalyst activation and CO 2 binding by navigating a perfect medium between the nonsterically encumbered bpy-based and the highly sterically encumbered mes2bpy-based precatalysts. Cyclic voltammetry conducted in CO 2 -saturated electrolyte for the (Ph) 2 bpy-based precatalyst [2-CH 3 CN] + confirms that CO 2 binding occurs at the two-electron-reduced activated catalyst [2] – in the absence of an excess proton source, in contrast to prior assumptions that all manganese catalysts require a strong acid for CO 2 binding. This observation is supported by computed free energies of the parent–child reaction for [Mn–Mn] o dimer formation, where increased steric hindrance relative to the bpy-based precatalyst correlates with favorable CO 2 binding. A critical balance must be adhered to, however, as the absence of steric bulk in the bpy-based precatalyst [1-CH 3 CN] + maintains a lower overpotential than [2-CH 3 CN] + at the protonation-first pathway with comparable kinetic performance, whereas an ~2-fold greater TOF max is observed at its reduction-first pathway with an almost identical overpotential as [2-CH 3 CN] + . Notably, excessive steric bulk in the mes2bpy-based precatalyst [3-CH 3 CN] + results in increased activation free energies of the C–OH bond cleavage transition states for both the protonation-first and the reduction-first pathways relative to both [1-CH 3 CN] + and [2-CH 3 CN] + . In fact, [3-CH 3 CN] + requires a 1 V window beyond its onset potential to reach its peak catalytic current, which is in contrast to the narrower (<0.30 V) potential response window of the remaining catalysts here studied. Furthermore, voltammetry recorded under 1 atm of CO 2 with 2.8 M (5%) H 2 O establishes [2-CH 3 CN] + to have the lowest overpotential (η = 0.75 V) in the series here studied, attributed to its ability to lie “on the fence” when providing sufficient steric bulk to hinder (but not prevent) [Mn–Mn] o dimerization, while simultaneously having a limited steric impact on the free energy of activation for the rate-determining C–OH bond cleavage transition state. While the methoxyphenyl bpy-based precatalyst [4-CH 3 CN] + possesses an increased steric presence relative to [2-CH 3 CN] + , this is offset by its capacity to stabilize the C–OH bond cleavage transition states of both the protonation-first and the reduction-first pathways by facilitating second coordination sphere H-bonding stabilization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Stability, Combustion, and Compatibility of High-Viscosity Heavy Fuel Oil Blends with a Fast Pyrolysis Bio-Oil

Properties related to the combustion, stability, and compatibility of blends composed of high-viscosity heavy fuel oil (HFO) and highly acidic pyrolysis bio-oil were determined to assess the utility of bio-oil as a marine fuel. The addition of bio-oil was shown to be fully stable with HFO at blend levels up to 50 mass % for up to 2 weeks. Bio-oil concentrations as low as 5 mass % significantly reduced the viscosity of HFO at 25 and 50 °C. Aging studies at 50 and 90 °C showed that the HFO inhibited the polymerization of bio-oil. The heating value and lubricity showed a linear dependency with bio-oil content, and combustion quality was acceptable for blends containing up to 15% bio-oil. The highly acidic bio-oil was found to be corrosive to carbon steel, 2.25Cr-1Mo steel, and 409 stainless steels, but not 304L and 316L. When blended into HFO at levels less than 19 mass %, no measurable corrosion was observed on any of the steel materials, but a 50 mass % concentration produced low-to-moderate corrosion in the carbon steel, 2.25Cr-1Mo steel, and 409 stainless steel grades. The combination of good blend stability, polymerization inhibition, reduced viscosity, and acceptable compatibility for low blend levels suggests that bio-oils may be suitable for use as a marine fuel.

09 BIOMASS FUELS↗
DOE OSTI2023

Organic sulfur from source to sink in low‐sulfate Lake Superior

Abstract Organic sulfur plays a crucial role in the biogeochemistry of aquatic sediments, especially in low sulfate (< 500 μ M) environments like freshwater lakes and the Earth's early oceans. To better understand organic sulfur cycling in these systems, we followed organic sulfur in the sulfate‐poor (< 40 μ M) iron‐rich (30–80 μ M) sediments of Lake Superior from source to sink. We identified microbial populations with shotgun metagenomic sequencing and characterized geochemical species in porewater and solid phases. In anoxic sediments, we found an active sulfur cycle fueled primarily by oxidized organic sulfur. Sediment incubations indicated a microbial capacity to hydrolyze sulfonates, sulfate esters, and sulfonic acids to sulfate. Gene abundances for dissimilatory sulfate reduction ( dsrAB ) increased with depth and coincided with sulfide maxima. Despite these indicators of sulfide formation, sulfide concentrations remain low (< 40 nM) due to both pyritization and organic matter sulfurization. Immediately below the oxycline, pyrite accounted for 13% of total sedimentary sulfur. Both free and intact lipids in this same interval accumulated disulfides, indicating rapid sulfurization even at low concentrations of sulfide. Our investigation revealed a new model of sulfur cycling in a low‐sulfate environment that likely extends to other modern lakes and possibly the ancient ocean, with organic sulfur both fueling sulfate reduction and consuming the resultant sulfide.

Phillips, Alexandra A.↗
DOE OSTI2019

Spontaneous Formation of >90% Optically Transmissive, Electrochemically Active CoP Films for Photoelectrochemical Hydrogen Evolution

Earth-abundant catalysts for the hydrogen-evolution reaction need increased mass loadings, relative to Pt films, to achieve comparable activity and stability in acidic electrolytes. We report herein that spontaneous nanostructuring of opaque, electrodeposited CoP films, 40–120 nm in thickness, leads to transparent electrocatalyst films that exhibit up to 90% optical transmission in the visible spectrum. The photocurrent density under simulated sunlight at a representative n + p-Si(100)/CoP photocathode increases by 200% after exposure to 0.50 M H 2 SO 4 (aq) and remains stable for 12 h of continuous operation. Atomic force microscopy and scanning electron microscopy of the film before and after exposure to 0.50 M H 2 SO 4 (aq) validate an optical model for transparent CoP films as probed with spectroscopic ellipsometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Askival: An altered feldspathic cumulate sample in Gale crater

Askival is a light-toned, coarsely crystalline float rock, which was identified near the base of Vera Rubin Ridge in Gale crater. We have studied Askival, principally with the ChemCam instrument but also using APXS compositional data and MAHLI images. Askival and an earlier identified sample, Bindi, represent two rare examples of feldspathic cumulate float rocks in Gale crater with >65% relict plagioclase. Bindi appears unaltered whereas Askival shows textural and compositional signatures of silicification, along with alkali remobilization and hydration. Askival likely experienced multiple stages of alteration, occurring first through acidic hydrolysis of metal cations, followed by deposition of silica and possible phyllosilicates at low T and neutral-alkaline pH. Through laser-induced breakdown spectroscopy compositional analyses and normative calculations, we suggest that an assemblage of Fe-Mg silicates including amphibole and pyroxene, Fe phases, and possibly Mg-rich phyllosilicate are present. Thermodynamic modeling of the more pristine Bindi composition predicts that amphibole and feldspar are stable within an upper crustal setting. This is consistent with the presence of amphibole in the parent igneous rocks of Askival and suggests that the paucity of amphiboles in other known Martian samples reflects the lack of representative samples of the Martian crust rather than their absence on Mars.

58 GEOSCIENCES↗
DOE OSTI2021

Investigations of the stability of etched or platinized p-InP(100) photocathodes for solar-driven hydrogen evolution in acidic or alkaline aqueous electrolytes

Here, the stability of p-InP photocathodes performing the hydrogen-evolution reaction (HER) has been evaluated in contact with either 1.0 M H 2 SO 4 (aq) or 1.0 M KOH(aq), with a focus on identifying corrosion mechanisms. Stability for the solar-driven HER was evaluated using p-InP electrodes that were either etched or coated with an electrodeposited Pt catalyst (p-InP/Pt). Variables such as trace O 2 were systematically controlled during the measurements. Changes in surface characteristics after exposure to electrochemical conditions as well as electrode dissolution processes were monitored using X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). In either H 2 SO 4 or KOH, etched p-InP photoelectrodes corroded cathodically under illumination, forming metallic In 0 at the electrode surface. In contrast, electrodeposition of Pt kinetically stabilized illuminated p-InP photocathodes in both H 2 SO 4 and KOH by inhibiting the cathodic corrosion pathway. Notably, when held at 0 V vs. the reversible hydrogen electrode (RHE) in 1.0 M H 2 SO 4 (aq), p-InP/Pt exhibited a stable current density (J) of ~–18 mA cm –2 for >285 h under simulated 1 Sun illumination. The long-term current density vs. potential (J–E) behavior at pH 0 and pH 14 of p-InP/Pt photocathodes correlated with changes in the surface chemistry as well as the dissolution of p-InP. In acidic media, the J–E behavior of p-InP/Pt photocathodes remained nearly constant with time, but the surface of a p-InP/Pt electrodes gradually turned P-rich via a slow and continuous leaching of In ions. In alkaline electrolyte, the surface of p-InP/Pt electrodes was passivated by formation of an InO x layer that exhibited negligible dissolution but led to a substantial degradation in the J–E characteristics. Consequently, changes in the catalytic kinetics and surface stoichiometry are both important considerations for determining the corrosion chemistry and the long-term operational stability of InP photoelectrodes.

14 SOLAR ENERGY↗
DOE OSTI2025

Cyanine-Incorporated Amorphous Polymeric Carbon Dots for Optical Reactive Oxygen Species Sensing

Reactive oxygen species (ROS) are common cellular oxidants that when overproduced by cellular stressors cause harm to cells. Detection of ROS is of utmost importance to understanding a wide variety of cellular function and toxicity mechanisms. Conventional ROS fluorescence assays involve using a single dye to visualize the ROS quantity. Herein, we describe ROS-sensitive, fluorescent-dye-incorporated carbon dots with dual fluorescence capabilities and good biocompatibility. Carbon dots (CDs) made of citric acid and urea were synthesized with incorporated cyanine-3-amine (Cy3), a bright red fluorescent dye, to create Cy3-CDs. Additionally, to get Cy3 into the ROS-sensitive form, this work demonstrated that Cy3 alone and Cy3 within carbon dots can be electrochemically reduced to their colorless ROS-sensitive form. Cy3, CDs, and Cy3-CDs are all responsive to additions of superoxide, leading to an increase in the fluorescence. Overall, this work examines how O 2 •– and additional oxidizers interact with CDs, Cy3, and Cy3-CDs, and molecular-level hypotheses are explored that will inform the design of future carbon dot-based ROS sensors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Standard Analytical Methods for Pyrolysis Bio-Oils

There has been significant recent interest in the production of renewable fuels and chemicals from biomass and waste feedstocks. Pyrolysis pathways produce a liquid bio-oil product, which must be processed further, or upgraded, to yield fuel or chemical products. Bio-oils are very complex and often unstable samples, and research and development on upgrading processes needs reliable analytical information. In particular, chemical characterization techniques are needed to quantify both functional groups and individual compounds present in bio-oils. Reliable analytics are also needed to enable the bioenergy industry, as industrial facilities often have different analytical needs and capabilities than research facilities. In this presentation, we will discuss the development of a suite of standard analytical methods for pyrolysis bio-oils. Analytical methods to be discussed include: Determination of Carbon, Hydrogen, Nitrogen, and Oxygen in bio-oils; Accelerated Aging of Fast Pyrolysis Bio-oil using Carbonyl Titration; Determination of Water Content in Bio-oils by Volumetric Karl Fischer Titration; Determination of Carbon Functional Groups; Elemental Analysis of Bio-oils by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES) - Na, K, Mg, Ca, S, P, and Fe; Determination of Phenolic Groups in Bio-oils using Revised Folin-Ciocalteu Methods: Single Cuvette and Plate Reader; Corrosivity of Bio-oils: Screening Test using Metal Leaching; Determination of Biogenic Content by 14C Measurement using Liquid Scintillation Counter. These new analytical methods are publicly available as Laboratory Analytical Procedures (https://www.nrel.gov/bioenergy/bio-oil-analysis.html), along with previously developed standard methods: GC-MS, Acid Titration, Carbonyl Titration, and 31P NMR. Additionally, the development of diffusion ordered NMR for characterization of bio-oil molecular weight will be discussed. Collectively, this suite of analytical methods represents the most comprehensive set of standard methods available for pyrolysis bio-oils. These standard methods are commonly used by the bioenergy community, and provide reliable information that enables research, scaleup, and industrial processing of biomass to produce renewable fuels and chemicals.

analytical↗