SEARCH · Search NASA

Results for “Mesh generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Coupled beam-target-moderator optimization for the Second Target Station

To support the design of the Second Target Station, that aims to provide the world’s highest peak brightness of cold neutrons, studies that optimize the dimensions of the target and moderators are invaluable. In this work, we investigate the influence of the target dimensions and beam profile on the performance and optimal size of the moderators. We perform optimization runs with detailed MCNP6.2 simulations using high-fidelity unstructured mesh geometries generated from parametrized CAD models. We demonstrate that small changes in target height do not influence the moderator performance if the beam dimensions are chosen adequately. We quantify the effect of beam footprint and target width on the moderator performance and show that the optimal moderator dimensions are insensitive to limited changes in target and beam profile.

Dakota↗

DOE OSTI2025

A three-dimensional laser ray-tracing methodology for radiation-hydrodynamics simulations

We report on a methodology for performing laser ray-tracing in three spatial dimensions for radiation-hydrodynamics simulation codes. Our method, which is an extension of that developed in Haines et al., Comput. Fluids 201, 104478 (2020), utilizes an automatically generated separate mesh for the laser ray-tracing from the radiation-hydrodynamics mesh. This enables the laser mesh to be tailored to minimize ray noise with significantly fewer rays than would be required when the ray-tracing is performed on the radiation-hydrodynamics mesh, primarily by allowing the use of high-aspect-ratio cells that are not suitable for hydrodynamics solvers. For a planar target, we show that our method provides a ≈ 100× reduction in computational expense to achieve a fixed level of ray noise relative to ray-tracing directly on the radiation-hydrodynamics mesh. The relatively low ray requirement also enables efficient computation of cross-beam energy transfer. Each cell in the logically cubic laser mesh is a non-convex dodecahedron with triangular sides, and numerical integration of the ray trajectories and inverse bremsstrahlung is performed by mapping each cell to the unit cube. We will describe our methodology in detail as well as its implementation in the xRAGE radiation-hydrodynamics code, discuss performance, and present the results from applying the methodology to test problems with analytic solutions for laser ray-tracing through a quadratic density gradient with an analytic solution as well as for a laser-driven heat front. In 3D radiation-hydrodynamics simulations of laser-driven experiments performed on the National Ignition Facility, laser ray-tracing with our methodology uses less than 1% of total computational time while introducing acceptably low levels of ray noise.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Tusqh

SAND2025-00675O Tusqh is a software tool that generates cubical meshes in 2D and 3D and computes the homology of these meshes using persistent homology. It includes a grid cell in the output if its volume-fraction is above a selectable threshold, estimated by sampling points within the cell. Tusqh incorporates anti-aliasing algorithms to mitigate grid orientation and scale effects. It is designed for creating finite element meshes for simulations and can be used in various applications such as heat diffusion, mechanical simulations, and computer graphics rendering. The software outputs meshes in an open format compatible with downstream software. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

SciDAC↗

DOE OSTI2026

FIREFLY: heat load and particle exhaust approximations for rapid evaluation of divertor designs

The divertor in a magnetic confinement fusion reactor is an essential component for power dissipation and particle removal. The FIREFLY package for rapid evaluation of divertor designs is presented as an extension of the FLARE code for field line reconstruction from a flux tube mesh. First, divertor loads are approximated with a simplified heat transport model. Neutralized particles are then sampled from the resulting load distribution, and the EIRENE code is used to track molecules and atoms in a plasma background while accounting for dissociation, charge exchange and ionization. Particles are removed on pumping surfaces in order to estimate the exhaust efficiency for a given divertor geometry. Optimization of the divertor geometry for more efficient particle exhaust is explored by using W7-X as an example, and the sensitivity to model parameters for the plasma background in the proxy calculations is evaluated.

mesh generation, magnetic field lines, scrape-off ↗

NASA NTRS1980

Grid generation for time dependent problems: Criteria and methods

The problem of generating local mesh refinements when solving time dependent partial differential equations was examined. The problem of creating an appropriate grid, given a mesh function h defined over the spatial domain is discussed. A data structure which permits efficient use of the resulting grid is described. A good choice for h is an estimate of the local truncation error, and several ways to estimate it are discussed. The efficiency and implementation problems of these error estimates were compared.

Berger, M.↗

NASA NTRS1981

The effect of surface boundary conditions on the climate generated by a coarse-mesh general circulation model

A hierarchy of experiments was run, starting with an all water planet with zonally symmetric sea surface temperatures, then adding, one at a time, flat continents, mountains, surface physics, and realistic sea surface temperatures. The model was run with the sun fixed at a perpetual January. Ensemble means and standard deviations were computed and the t-test was used to determine the statistical significance of the results. The addition of realistic surface physics does not affect the model climatology to as large as extent as does the addition of mountains. Departures from zonal symmetry of the SST field result in a better simulation of the real atmosphere.

Cohen, C.↗

NASA NTRS1982

Finite volume calculation of three-dimensional potential flow around a propeller

The finite volume scheme of Jameson (1977) is used to calculate potential flow around a propeller rotating at high speed. An H-type mesh is generated and used successfully in the calculations. A test calculation with a thick blade cross section shows that the present code is capable of computing the propeller flow at the advance Mach number 0.8. The possible physical mechanisms which may play an important role in the propeller aerodynamics are discussed.

Jou, W.-H.↗

NASA NTRS1986

Multiple Grids in Finite-Difference Flow Analysis

Multiple solutions superimposed to resolve flows about complex configurations. Use of multiple, overset grids in computational fluid dynamics extends application of finite-difference methods to more complex configurations. Rather than trying to generate single mesh about all components of configuration, multiple, individual meshes used, then overset on major grid. Major grid used to resolve flow field or wrapped around main component.

Dougherty, F. C.↗

NASA NTRS1985

Stress analyses of B-52 pylon hooks

The NASTRAN finite element computer program was used in the two dimensional stress analysis of B-52 carrier aircraft pylon hooks: (1) old rear hook (which failed), (2) new rear hook (improved geometry), (3) new DAST rear hook (derated geometry), and (4) front hook. NASTRAN model meshes were generated by the aid of PATRAN-G computer program. Brittle limit loads for all the four hooks were established. The critical stress level calculated from NASTRAN agrees reasonably well with the values predicted from the fracture mechanics for the failed old rear hook.

Ko, W. L.↗

NASA NTRS1986

Transition and mixing in axisymmetric jets and vortex rings

A class of impulsively started, axisymmetric, laminar jets produced by a time dependent joint source of momentum are considered. These jets are different flows, each initially at rest in an unbounded fluid. The study is conducted at three levels of detail. First, a generalized set of analytic creeping flow solutions are derived with a method of flow classification. Second, from this set, three specific creeping flow solutions are studied in detail: the vortex ring, the round jet, and the ramp jet. This study involves derivation of vorticity, stream function, entrainment diagrams, and evolution of time lines through computer animation. From entrainment diagrams, critical points are derived and analyzed. The flow geometry is dictated by the properties and location of critical points which undergo bifurcation and topological transformation (a form of transition) with changing Reynolds number. Transition Reynolds numbers were calculated. A state space trajectory was derived describing the topological behavior of these critical points. This state space derivation yielded three states of motion which are universal for all axisymmetric jets. Third, the axisymmetric round jet is solved numerically using the unsteady laminar Navier Stokes equations. These equations were shown to be self similar for the round jet. Numerical calculations were performed up to a Reynolds number of 30 for a 60x60 point mesh. Animations generated from numerical solution showed each of the three states of motion for the round jet, including the Re = 30 case.

Allen, G. A., Jr.↗

NASA NTRS1987

Adaptive remeshing for compressible flow computations

The present, quality-enhancing adaptive-mesh procedure for two-dimensional Euler equation steady state solutions is implemented by means of linear triangular elements and an explicit time-stepping scheme, in conjunction with a finite element solution algorithm. The meshes thus generated typically take the form of stretched elements in the vicinity of one-dimensional flow features; a considerable variation in element size may thereby emerge which allows the desired high-quality solutions to be obtained with commensurately high computational efficiency.

Peraire, J.↗

NASA NTRS1988

Advanced composite turboprops - Modeling, structural, and dynamic analyses

This paper presents a structural and dynamic analysis of a scaled-down wind tunnel model propfan blade made from fiber composites. This blade is one of a series of propfan blades that have been tested at the NASA Lewis Research Center wind tunnel facilities. The blade is highly swept and twisted and of the spar/shell construction. Due to the complexity of the blade geometry and its high performance, it is subjected to much higher loads and tends to be much less stable than conventional blades. The structural and dynamic analyses of the blade were performed using the NASA-Lewis COBSTRAN computer code. COBSTRAN is designed to generate the mesh and calculate the anisotropic material properties for composite blade analysis. Comparison of analytical and experimental mode shapes and frequencies are shown, verifying the model development and analysis techniques used. The methodologies and programs developed for this analysis are directly applicable to other propfan blades.

Aiello, R. A.↗

NASA NTRS1988

Robust vortex methods for three-dimensional incompressible flows

Vortex methods for the numerical simulation of incompressible three-dimensional flows at high Reynolds number are discussed. Particular emphasis is placed on schemes that prevent the excessive generation of mesh elements, include viscous effects, and are relatively inexpensive even as the number of elements becomes large. Several simulations are presented involving the interaction of vortex rings.

Chua, K.↗

NASA NTRS1989

A thermal analysis of a spirally wound battery using a simple mathematical model

A two-dimensional thermal model for spirally wound batteries has been developed. The governing equation of the model is the energy balance. Convective and insulated boundary conditions are used, and the equations are solved using a finite element code called TOPAZ2D. The finite element mesh is generated using a preprocessor to TOPAZ2D called MAZE. The model is used to estimate temperature profiles within a spirally wound D-size cell. The model is applied to the lithium/thionyl chloride cell because of the thermal management problems that this cell exhibits. Simplified one-dimensional models are presented that can be used to predict best and worst temperature profiles. The two-dimensional model is used to predict the regions of maximum temperature within the spirally wound cell. Normal discharge as well as thermal runaway conditions are investigated.

Evans, T. I.↗

NASA NTRS1990

Shock interference studies on a circular cylinder at Mach 16

This paper presents the results of a computational study on the shock interference problems on a cylindrical body typical of an engine inlet cowl leading edge at a nominal Mach number of 16. The two-dimensional Navier-Stokes equations are solved assuming the flow to be in chemical and thermal equilibrium and using a finite element method. The algorithm employs a cell-centered fully implicit upwind scheme. Adaptively generated unstructured meshes of triangles and quadrilaterals are employed. Under certain conditions the finite element code resulted in oscillatory solutions for shock interference at Mach 16. Some of the causes of the unsteady behavior are identified, and to the extent possible, such situations are avoided in the present application. Two shock interference conditions involving a Type IV (supersonic jet) and a Type III (attaching shear layer) are solved. The results are compared with available experimental data and reasonable agreement is observed. A semi-empirical method is also used to estimate the maximum surface heat flux and static pressure.

Prabhu, Ramadas K.↗

NASA NTRS1991

Computational studies of a fluid spike as a leading edge protection device for shock-shock interference heating

The effectiveness of a fluid spike as a device to protect leading edges of hypersonic atmospheric flight vehicles from high aerothermal loads produced by complex shock-shock interference is studied. The two-dimensional Navier-Stokes equations are solved using an unstructured cell-centered, fully implicit, flux-difference split algorithm. Adaptively generated unstructured meshes are employed. A type IV shock-shock interference for Mach 8 flow on a cylindrical leading edge with and without a small contraflow supersonic jet (fluid spike) placed at two different locations on the body is solved. A typical flow past a blunt body with a type IV shock-shock interference produces very high pressures and heat fluxes on the leading edge. Present results indicate that a fluid spike displaces the bow shock further in front of the body and modifies the shock-shock interference pattern. This leads to reduced peak pressures and heat fluxes on the body.

Prabhu, Ramadas K.↗

NASA NTRS1992

Progress in integrated analysis with adaptive unstructured meshing

Design of lightweight structures and thermal protection systems for hypersonic vehicles depend on accurate prediction of aerothermal loads, structural temperatures and their gradients, and structural deformations and stresses. Concentration is on an alternative meshing technique which generates an entirely new adaptive unstructured mesh based on the solution obtained from the earlier mesh. The technique combined with the finite element method has been shown to significantly improve the efficiency and accuracy of the fluid, thermal, and structural analyses. Current capability of the adaptive unstructured meshing technique for the integrated fluid-thermal-structural analysis is described first. The technique was extended to transient thermal analysis of structures with time-dependent adaptive meshing to capture the detailed temperature response with a minimum number of unknowns and computational cost. Both linear and higher-order finite elements are implemented to demonstrate the generality of the technique and to investigate their solution accuracy. Currently, the adaptive meshing technique is being developed for plane structures that can be modeled with membrane elements and built-up structures modeled with membrane and bending elements. The capability of the technique to these different disciplinary problems is demonstrated by several examples.

Dechaumphai, Pramote↗

NASA NTRS1992

Tools and techniques for estimating high intensity RF effects

Tools and techniques for estimating and measuring coupling and component disturbance for avionics and electronic controls are described. A finite-difference-time-domain (FD-TD) modeling code, TSAR, used to predict coupling is described. This code can quickly generate a mesh model to represent the test object. Some recent applications as well as the advantages and limitations of using such a code are described. Facilities and techniques for making low-power coupling measurements and for making direct injection test measurements of device disturbance are also described. Some scaling laws for coupling and device effects are presented. A method for extrapolating these low-power test results to high-power full-system effects are presented.

Zacharias, Richard L.↗