Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model transferability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effect of air path heat losses at different locations in vapor compression-based clothes dryer: Quasi-steady modeling and design implications

Clothes drying is among the most power-intensive household end uses, and vapor compression-based clothes dryers offer substantial energy cost savings compared with conventional electric heater dryers. However, parasitic heat losses along the air path, that is, heat loss at the upstream of the drum, inside the drum, and at downstream of the drum, remain rarely quantified, but can strongly affect overall performance according to experiments. Here, this study enhances a vapor compression simulation model by integrating a validated drum model using a dimensionless heat-and-mass-transfer effectiveness correlation derived from 63 drying tests in the literature to form a quasi-steady dryer simulation model. The model is validated against laboratory measurements of a baseline dryer. The impact of heat losses is simulated at three locations and explored through 16 heat loss cases spanning two loads (2 and 5 kg), two airflow rates, and multiple loss distributions. For a 5 kg wet load, eliminating pre-drum and in-drum losses reduces total energy use by up to 34–35% and shortens drying time by 27–38% compared with the baseline. At a 2 kg wet load, introducing post-drum heat loss lowers energy costs by up to 23% and reduces operation time by up to 57% compared with the baseline. The results demonstrate that the impact of heat loss is location dependent. Vapor compression dryers should minimize pre-drum and in-drum losses while potentially exploiting post-drum heat dissipation to enhance the drying rate and energy cost savings.

Dryer↗
DOE OSTI2024

Alternating conduction and convection drying of paper – an experimental analysis with a continuous data acquisition approach

In conventional multi-cylinder drying of paper and board, both conductive drying from steam-heated dryer cylinders and convective drying by flowing air over the paper surface in the pockets are used. Conductive drying from steam-heated drying cylinders is a critical component in providing the necessary thermal energy to paper and board as they dry. Steam temperature and internal and external resistances at the contacting surface are critical process parameters influencing the conductive drying process. An experimental setup was developed to study the alternating conductive and convective drying of paper and board. Paper sheet moisture, temperature, and temperature distribution within the heated platen and the instantaneous heat flux as the sheet was being dried were measured. The instantaneous heat flux, contact heat transfer coefficient, and drying rates were determined as drying proceeds. Experimental results, as well as comparisons to literature and commercial data, are presented. The conductive heat transfer coefficients determined were compared to traditional correlations normally used in the modeling of paper drying. Similarly, the convective heat and mass transfer coefficients are also determined and compared to literature data. In addition to the evaluation of alternating conductive and convective drying characteristics of paper and board, the potential inclusion of auxiliary energy components will also be included. Experimental results from the conduction and convection drying system are presented. Furthermore, this data will be useful in process development, intensification of manufacturing processes, and modeling and simulation of paper drying processes.

42 ENGINEERING↗
DOE OSTI2025

Bayesian prior construction for uncertainty quantification in first-principles statistical mechanics

First-principles statistical mechanics enables the prediction of thermodynamic and kinetic properties of materials, but is computationally expensive. Many approaches require surrogate models to calculate energies within Monte Carlo or molecular dynamics simulations. Inexpensive surrogates such as cluster expansions enable otherwise intractable calculations by interpolating data from higher accuracy methods, such as Density Functional Theory (DFT). Surrogate models introduce uncertainty into downstream calculations, in addition to any uncertainty inherent to DFT calculations. Bayesian frameworks address this by quantifying uncertainty and incorporating expert knowledge through priors. However, constructing effective priors remains challenging. This work introduces and describes practical strategies for building Bayesian cluster expansions, focusing on basis truncation, hyperparameter selection, and ground state replication. We analyze multiple basis truncation schemes, compare cross-validation to the evidence-approximation for hyperparameter optimization, and provide methods to find and enforce ground-state-preserving models through priors. Additionally, we compare the uncertainties between different approximations to DFT (LDA, PBE, SCAN) against the uncertainty introduced with the use of cluster expansion surrogate models. These approaches are demonstrated on the BCC Li x Mg 1-x and Li x Al 1-x alloys, which are both of interest for solid-state Li batteries. Our results provide guidelines for constructing and utilizing Bayesian cluster expansions, thereby improving the transparency of materials modeling. Furthermore, the approaches and insights developed in this work can be transferred to a wide range of cluster expansion surrogate models, including the atomic cluster expansion and related machine-learned interatomic potential architectures.

Alloy theory↗
DOE OSTI2025

Automated Fire Detection for Industrial Settings with Pretrained Convolutional Networks

Early fire detection in industrial environments is critical to preventing equipment damage, personal injury, and operational disruptions. Traditional smoke detectors, while effective, often experience delays due to the time required for smoke to reach sensors, allowing fires to spread. Manual fire watch operations and human surveillance of camera feeds are resource-intensive and prone to human error. To address these challenges, this paper explores the application of convolutional neural networks for automated fire detection, specifically in industrial settings. By leveraging 11 different pre-trained machine vision models from TensorFlow and enhancing them with transfer learning on a custom-built industrial fire dataset, we optimized fire detection performance. Here, we analyzed each machine vision model architecture in terms of its depth, width, and input image resolution, considering both resource requirements and detection accuracy. We further explored the option of combining multiple models into an ensemble classifier to evaluate whether the performance improvements could justify the much greater computational complexity and other practical impacts. A cost-benefit analysis is presented to evaluate the trade-offs between performance and computational expense. Our findings identify that EfficientNetV2L, specifically tailored for industrial applications, provides the optimal balance between costs involved in training and using the model versus the overall fire detection performance. Additionally, we present a qualitative analysis of model performance using the technique of gradient-based class activation mapping to provide explainability by visualizing model decisions.

artificial intelligence↗
DOE OSTI2026

Reservoir-scale model of geologic hydrogen production from serpentinization: Cyclic injection in a dual-permeability fracture-matrix system

Geologic hydrogen (GeoH 2 ) from serpentinization is a promising low-carbon resource, but its reservoir-scale behavior remains poorly understood. We develop a dual-permeability reactive transport model for an injector–producer well pair in ultramafic rock that couples multiphase flow, heat transfer, geochemistry, and porosity–permeability evolution. Here, the model is calibrated to olivine flow-through experiments and upscaled to two-year long simulations with continuous injection and cyclic injection with shut-in-to-injection ratios (SIR = 1, 0.5, 0.1). Olivine reacts along high-flux pathways to form lizardite and magnetite, increasing pH; H 2 (aq) and H 2 (g) peak early and then decline as exsolution and advective export outpace local generation. Continuous injection yields the highest cumulative H 2 but the lowest water-use efficiency (1.138 x 10 –6 mol/kgw). Cyclic injection increases this ratio to 1.35 x 10 –6 , 1.377 x 10 –6 , and 1.182 x 10 –6 mol/kgw for SIR = 1, 0.5, and 0.1, respectively; SIR = 0.5 provides a ~20% improvement over continuous injection and the best compromise for pilot design.

08 HYDROGEN↗
DOE OSTI2025

Toward a Unified Kinetic Model of Nitrogenase Catalysis

The microbial enzyme nitrogenase catalyzes the MgATP-dependent reduction of N 2 to 2NH 3 , a transformation central to the global nitrogen cycle. While the canonical Thorneley−Lowe (TL) kinetic model has long served as a mechanistic framework, it does not incorporate several recent insights. Here, we present an updated kinetic model for Monitrogenase that incorporates these new findings. A significant insight is that electron transfer (ET) from the reduced Fe protein to the FeMo-cofactor is gated by MgATP-dependent conformational transitions and can be described as a probabilistic event that is dependent on the ligand bound to the active-site metallocofactor. The updated kinetic model quantitatively reproduces steady-state product formation rates across a broad range of experimental conditions, yielding revised estimates for key rate constants. It is demonstrated that under N 2 turnover, the probability of productive ET to the active site decreases by ∼60%, resulting in a significant fraction of Fe protein cycles that are unproductive for electron delivery. This mechanistic feature explains the observed rate limitation in N 2 reduction and implies a revised minimum energetic cost of approximately 25 MgATP per N 2 reduced. Integrating these new features into the revised kinetic model provides a more complete and usable foundation for understanding nitrogenase catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Development of a two-zone zero-dimensional mixing model for actively fueled prechamber engines

In this numerical work, a zero-dimensional, two-zone mixing model was developed and validated to capture the mixture preparation process of an actively fueled prechamber engine. The model was developed for ethanol-gasoline fuel blends but is applicable to various fuels of interest relevant to prechamber applications. The model was exercised to demonstrate the effects of boundary conditions, fuel composition, and residual content on the mixture stoichiometry predictions. The 0D model showed reasonable agreement in prechamber equivalence ratio predictions with higher fidelity computational fluid dynamics modeling, but the accuracy of model was constrained to the governing assumptions of the injection process. The modeling assumptions surrounding the non-dimensional injection of mass into the prechamber were scrutinized to identify key areas of model improvement. The results indicate heat transfer effects play a crucial role in the evaporation of the fuel within the confined auxiliary chamber, especially when considering fuels with high latent heat of vaporization. Additionally, the presence of fuel films that collect on the prechamber surfaces complicated the modeled evaporative cooling loses as the modeling suggests the films evaporate primarily by means of conduction from the boundary. Furthermore, the developed model serves as a simplified framework to generate calibration maps of prechamber fueling or run real time as an open loop control strategy such that desired prechamber mixture proportions are effectively targeted.

Zero-dimensional↗
DOE OSTI2026

Influence of Surfactants on Noble Metal Liquid-Gas Interface Mass Transfer in Molten Salt Reactors

Noble metals, a group of insoluble fission products (FPs), can accumulate in molten salt reactors (MSRs) and influence system performance and safety through deposition. Upon generation in fission, noble metals are transported by circulating salt and may either deposit on structural surfaces or enter the circulating gas bubble interfaces. While sparging was primarily designed for xenon and krypton removal, the mass transfer of noble metals into bubble interfaces highlights a potential pathway for their transport and partial extraction. The properties of the liquid-gas interface therefore play an important role in noble metal deposition and removal behaviors. Observations from earlier studies suggest that noble metals accumulated at the bubble interface can act as surfactants, making the bubble interface partially immobile. This behavior reduces the mass transfer capacity of circulating bubbles and affects both the overall distribution of noble metals in the loop and their removal efficiency. To investigate the influence of surfactants on noble metal transport, deposition, and extraction behaviors in MSRs, a previously developed and validated species transport model incorporating noble metal interphase mass transfer was used to simulate these behaviors. Two designed cases were studied to predict the distribution of 132Te along the Molten Salt Reactor Experiment (MSRE) loop under different bubble interface conditions. The results show that the mass transfer coefficients at the liquid-gas interface, determined by bubble interface characteristics, significantly influence noble metal distribution within the reactor loop. These findings emphasize the importance of continuously introducing fresh circulating bubbles into the molten salt to improve the removal efficiency of insoluble FPs from the MSR primary loop.

MSR↗
DOE OSTI2025

Modular Hydronic Room Conditioning System (CRADA NFE-24-10120 Final Report)

This project presents the development and validation of high-fidelity numerical models for fin-tube heat exchangers to enable accurate performance prediction and informed design optimization. The modeling framework integrates detailed geometric specifications, thermophysical property data, and system-level constraints to simulate the heat exchanger’s behavior under a range of operating conditions. The model is calibrated using real-world product specifications and validated against experimental data collected from controlled cooling and heating tests. In cooling mode, the model captures the overall trends in capacity and outlet air temperature but tends to underpredict latent effects, especially at lower air flow rates. In heating mode, the simulation consistently overestimates both the thermal capacity and outlet air temperature, indicating the need for refinement in air-side heat transfer assumptions. Despite these deviations, the model provides a solid foundation for optimization, allowing key design variables to be tuned within physical and performance-based constraints. This research advances the ability to simulate, validate, and optimize fin-tube heat exchanger designs with greater confidence and efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Modular Hydronic Room Conditioning System

This project presents the development and validation of high-fidelity numerical models for fin-tube heat exchangers to enable accurate performance prediction and informed design optimization. The modeling framework integrates detailed geometric specifications, thermophysical property data, and system-level constraints to simulate the heat exchanger’s behavior under a range of operating conditions. The model is calibrated using real-world product specifications and validated against experimental data collected from controlled cooling and heating tests. In cooling mode, the model captures the overall trends in capacity and outlet air temperature but tends to underpredict latent effects, especially at lower air flow rates. In heating mode, the simulation consistently overestimates both the thermal capacity and outlet air temperature, indicating the need for refinement in air-side heat transfer assumptions. Despite these deviations, the model provides a solid foundation for optimization, allowing key design variables to be tuned within physical and performance-based constraints. This research advances the ability to simulate, validate, and optimize fin tube heat exchanger designs with greater confidence and efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Development of MOSCATO: A CFD-Level Electrochemistry and Corrosion Simulator for Molten Salt Systems

For both coolant and fueled variants of molten salt reactors (MSRs), the corrosion of structural materials is a significant challenge. The corrosion stems from chemical and electrochemical reactions initiated by fissile material, fission products, and impurities in the salt. Lower-fidelity models rely on empirical correlations for mass transfer, simplified lumped temperature profiles, and similar assumptions. They do not capture detailed spatial variations in complex geometries, creating the need for high-fidelity modeling to bridge this gap.As we approach the demonstration and possible deployment of MSRs in this decade, the development of a high-fidelity, high-performance simulator becomes imperative. To simulate the complex electrochemical environment and corrosion within molten salt systems, we have developed the Molten Salt Chemistry And TranspOrt (MOSCATO) code. This endeavor is comprised of three essential components. First, mass transfer equations are coupled with the Navier-Stokes equations in order to account for the transport of species in the salt. Second, the diffusion of alloy constituents, such as Cr, Fe, Ni, etc. is simulated within the structural metals. Third, the alloy and salt domains are coupled to account for the heterogeneous chemical and electrochemical reactions that occur at the salt-alloy interface.MOSCATO manages all three components within the framework of the highly scalable, open-source spectral element method computational fluid dynamics code Nek5000/NekRS. This integration enables MOSCATO to harness the immense computational power of modern high-performance computing resources, ensuring both high fidelity and computational speed.In addition to code development, we have initiated a comprehensive verification and validation campaign, utilizing data from diverse sources. First, MOSCATO's electrochemical solver was verified with reference numerical data. Then validation occurred against experiments: one of a thermal galvanic cell and the other for corrosion in flowing molten salt of FLiNaK (LiF-NaF-KF). This campaign verified and validated MOSCATO as a reliable tool for simulating electrochemical environments and corrosion in molten salt systems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Fast baryonic field painting for Sunyaev-Zel’dovich analyses: Transfer function vs hybrid effective field theory

Here, we present two approaches for “painting” baryonic properties relevant to the Sunyaev-Zel’dovich (SZ) effect—optical depth and Compton-y—onto three-dimensional N-body simulations, using the MillenniumTNG suite as a benchmark. The goal of these methods is to produce fast and accurate reconstruction methods to aid future analyses of baryonic feedback using the SZ effect. The first approach employs a Gaussian process emulator to model the SZ quantities via a transfer function, while the second utilizes hybrid effective field theory (HEFT) to reproduce these quantities within the simulation. Our analysis involves comparing both methods to the true MillenniumTNG optical depth and Compton-y fields using several metrics, including the cross-correlation coefficient, power spectrum, and power spectrum error. Additionally, we assess how well the reconstructed fields correlate with dark matter haloes across various mass thresholds. The results indicate that the transfer function method yields more accurate reconstructions for fields with initially high correlations (r ≈ 1), such as between the optical depth and dark matter fields. Conversely, the HEFT-based approach proves more effective in enhancing correlations for fields with weaker initial correlations (r ∼ 0.5), such as between the Compton-y and dark matter fields. Lastly, we discuss extensions of our methods to improve the reconstruction performance at the field level.

Liu, R. Henry [University of California, Berkeley,↗
DOE OSTI2025

Openpronghorn

OpenPronghorn is a simulation tool specifically tailored for modeling thermal-hydraulic phenomena in advanced nuclear reactors. It is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE), an open-source platform that facilitates the development of high-performance scientific computing applications. OpenPronghorn solves the Navier-Stokes equations, which describe the conservation of mass, momentum, and energy in fluid flows, using the finite volume numerical method. The code supports a wide range of fluid flow conditions that are applicable to nuclear reactors, including incompressible and weakly compressible flows, as well as single-phase and multiphase flows. It is capable of modeling diverse flow regimes, including laminar and turbulent flows, using various turbulence models such as the standard k-epsilon models, the v2f model, and the mixing length model. For multiphase flows, OpenPronghorn employs a mixture a Eulerian modeling approach with mixture, drift-flux, and full Eulerian models, and includes open-sourced interfacial transfer correlations for drag, exchange, and heat transfer coming from the scientific literature. OpenPronghorn's modular design allows it to handle multiscale simulations, ranging from detailed Reynolds-Averaged Navier Stokes (RANS) simulations to coarse-mesh and lumped parameter models. This flexibility enables users to perform high-fidelity simulations of specific reactor components as well as system-level analyses of entire reactor circuits. The code can be coupled with other MOOSE-based tools using the MultiApp system, allowing for the transfer of coupling quantities such as mass flow rates, heat fluxes, and boundary conditions between different simulation scales. One of the main features of OpenPronghorn is the it includes built-in validation cases from the open-source scientific literature and supports the implementation of user-defined models and correlations through MOOSE's FunctorMaterial system. OpenPronghorn is designed to be computationally efficient, leveraging the SIMPLE projection method for large-scale problems, and can be run on high-performance computing systems to handle the extensive computational demands of detailed reactor simulations. Overall, OpenPronghorn is a versatile and robust tool that provides critical insights into the thermal-hydraulic behavior of advanced nuclear reactors, supporting the design, safety, and optimization of next-generation nuclear energy systems.

Retamales, Mauricio Eduardo Tano [Idaho National L↗
DOE OSTI2024

Liquid lithium divertor analysis using coupled plasma material interaction model

A liquid lithium divertor can improve performance of future fusion devices by creating efficient power exhaust and improving the energy confinement via pumping of the hydrogen isotopes. In addition, significantly higher heat fluxes can be handled if controlled vapor shielding is used to redistribute the divertor heat flux over a wider area. Design and optimization of such a system calls for an analysis model which includes a strong two-way coupling between the plasma and divertor material. The incoming plasma heat and particle flux will affect the divertor surface temperature, which is a defining factor of the lithium evaporative and sputtered flux going into the plasma. Results of the coupled model based on the plasma edge code SOLPS-ITER and the computational fluid dynamics (CFD) code ANSYS-CFX will be presented for different configurations. An analytical slab flow model is used as a heat transfer boundary condition for SOLPS, defining particle flux from the wall via calculation of the surface temperature. At the final step, results of the SOLPS analysis are verified using a 3D CFD magnetohydrodynamics (MHD) analysis which uses heat and particle flux from SOLPS as a boundary condition. In addition to plasma heat flux, both analytical and CFD temperature models include several plasma material interaction effects, such as lithium evaporation, condensation and sputtering based on deuterium target flux. New adatom sputtering model based on the available experimental data is presented. Analytical model is expanded to include free surface axisymmetric configurations. Results of parametric studies of the divertor configurations with different lithium inlet temperature and velocity will be presented leading to the optimal design resulting in the lowest possible lithium contamination in the core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Bayesian calibration of bubble size dynamics applied to CO 2 gas fermenters

To accelerate the scale-up of gaseous CO 2 fermentation reactors, computational models need to predict gas-to-liquid mass transfer which requires capturing the bubble size dynamics, i.e. bubble breakup and coalescence. However, the applicability of existing models beyond air–water mixtures remains to be established. Here, an inverse modeling approach, accelerated with a neural network surrogate, calibrates the breakup and coalescence closure models, that are used in class methods for population balance modeling (PBM). The calibration is performed based on experimental results obtained in a CO 2 -air–water-coflowing bubble column reactor. Bayesian inference is used to account for noise in the experimental dataset and bias in the simulation results. To accurately capture gas holdup and interphase mass transfer, the results show that the breakage rate needs to be increased by one order of magnitude. In conclusion, the inferred model parameters are then used on a separate configuration and shown to also improve bubble size distribution predictions.

09 BIOMASS FUELS↗
DOE OSTI2025

A Unified Interpretation of Variability in Precipitation Isotope Ratios

Abstract Several mechanisms have been proposed to explain why the isotope ratios of precipitation vary in space and time and why they correlate with other climate variables like temperature and precipitation. Here, we argue that this behavior is best understood through the lens of radiative transfer, which treats the depletion of atmospheric vapor transport by precipitation as analogous to the attenuation of light by absorption or scattering. Building on earlier work by Siler et al., we introduce a simple model that uses the equations of radiative transfer to approximate the two-dimensional pattern of the oxygen isotope composition of precipitation ( δ p ) from monthly mean hydrologic variables. The model accurately simulates the spatial and seasonal variability in δ p within a state-of-the-art climate model and permits a simple decomposition of δ p variability into contributions from gradients in evaporation and the length scale of vapor transport. Outside the tropics, δ p is mostly controlled by gradients in evaporation, whose dependence on temperature explains the positive correlation between δ p and temperature (i.e., the temperature effect). At low latitudes, δ p is mostly controlled by gradients in the transport length scale, whose inverse relationship with precipitation explains the negative correlation between δ p and precipitation (i.e., the amount effect). This suggests that the temperature and amount effects are both mostly explained by the variability in upstream rainout, but they reflect distinct mechanisms governing rainout at different latitudes. Significance Statement The isotopic composition of precipitation has long been used to make inferences about past climates based on its observed relationship with precipitation in the tropics and with temperature at higher latitudes. These relationships—known as the “amount effect” and “temperature effect,” respectively—have been attributed to many different mechanisms, most of which are thought to operate at either high or low latitudes but not both. Here, we present a unified framework for interpreting the isotope variability that can explain the latitude dependence of the temperature and amount effects despite making no distinction between high and low latitudes. Although our results are generally consistent with certain interpretations of the amount effect, they suggest that the temperature effect is widely misunderstood.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

The 3D clustering of Lyman Alpha Emitters measured with DESI

We present a clustering analysis of Lyman-$α$ emitters (LAEs) using spectroscopic observations from the Dark Energy Spectroscopic Instrument (DESI) of candidates selected from the Blanco/DECam Intermediate-Band Imaging Survey (IBIS). We measure the two-point correlation function and the power spectrum, including cross-correlations with DESI quasars. Using both analytical and halo occupation distribution (HOD) simulation-based modeling, we find a linear bias of $b \sim 2.31$--$2.62$ for LAEs over the redshift range $2.26 < z < 3.41$. The analytical modeling also provides constraints on the strength of radiative transfer effects, while the HOD analysis characterizes the LAE-halo connection across multiple models. Finally, we quantify the magnitude of non-perturbative clustering effects such as Fingers of God in the LAE population, providing essential input for the accurate modeling of LAE-based cosmological analyses in forthcoming high-redshift surveys such as DESI-II.

Ebina, H. [UC, Berkeley; LBL, Berkeley] (ORCID:000↗