Search NASA⌕ Search

SEARCH · Search NASA

Results for “Models, Genetic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Hydrogen Production System Scaling Using a High-Fidelity Simulation-Optimization Framework

Proton exchange membrane (PEM) electrolyzers are widely used for hydrogen production, yet few validated, high-fidelity tools can reliably guide scale-up. Using measured performance from a 50-hour hardware-in-the-loop pilot test, a physics-based, plant-level model of a 1.25 MW PEM electrolyzer and its balance-of-plant (BoP) subsystems is developed and validated. The model couples electrochemistry and thermal/flow submodels and is calibrated against pilot test data via a genetic algorithm (GA) workflow. Validation yields a mean absolute percentage error (APE) of 0.43% for cell voltage and stack power. Two scale-out strategies are then benchmarked under a common 7-day wind-and-photovoltaic (PV) profile: (i) linear duplication of 1.25 MW blocks and (ii) shared-BoP architectures. Sharing BoP between stacks reduces BoP energy by 27% at 10 MW and 34% at 100 MW (vs. linear duplication) and improves system specific energy consumption (SEC) to 52.9 and 52.6 kWh/kg, respectively (from 54.0 kWh/kg with linear duplication). Partial-load studies (25-100% set-point) show that cumulative hydrogen production remains nearly constant down to 50% load because all cases use the same weekly renewable-energy input. Below 50%, the power cap limits how much energy can be used within 168 h, which reduces hydrogen output. The model further indicates that the practical operating optimum lies between 50% and 85% load, where efficiency gains begin to appear without significant loss in hydrogen output. Moreover, the efficiency gains at lower loads are offset by reduced production. The validated framework supports scenario-based engineering trade-off studies for large configurations (10-100 MW) and for operating policies under variable renewables.

08 HYDROGEN↗
NASA NTRSDate not supplied

The Pheno-Evo Model: Evolution of Microbial Phenotypic Diversity in 2D Space

Biologists appreciate microbes for their simplicity and predictability: we assume that a population of genetically identical cells in a uniform environment will all behave the same way. While this assumption is often useful, it is also often wrong. Not only might microbes in a clonal population act differently from one another, the differences may be categorical (growing v. non-growing; toxin-sensitive v. tolerant), and this diversity might be an evolved trait conferring increased fitness on the population. How does such phenotypic heterogeneity evolve? And how does a population find the optimal distribution of phenotypes for a given environment? Efforts at modeling microbial phenotypic heterogeneity often focus on populations with two discrete phenotypic types; phenotypes in continuous distributions remain poorly explored. To address this gap and to explore the role of spatial relationships, we use agent-based modeling to simulate a phenotypically diverse population of microbial cells evolving in the presence of periodic toxic stress. Cells on patches in a 2D grid may degrade toxin, suffer damage from toxin, switch phenotype, and reproduce. An individual's phenotype its toxin degradation rate-- for which there is a tradeoff with reproduction-- and the genotype encodes the distribution of phenotypic values in the population. The rate of toxin diffusion determines how individuals influence their neighbors' environments. We examine the effects of toxin concentration, diffusion rate, and environmental predictability on the survival success of populations with different phenotype distributions, and populations' evolutionary trajectories when phenotype distribution is allowed to evolve. We conduct all simulations on the platform NetLogo, which provides a friendly interface allowing users of any experience level to tweak parameters and run their own simulations. We have also created custom tools in R for analyzing and visualizing the results of multiple runs.

microbial evolution↗
NASA NTRS2006

Comparison of a Convected Helmholtz and Euler Model for Impedance Eduction in Flow

Impedances educed from a well-tested convected Helmholtz model are compared to that of a recently developed linearized Euler model using two ceramic test liners under the assumed conditions or uniform flow and a plane wave source. The convected Helmholtz model is restricted to uniform mean flow whereas the linearized Euler model can account for the effect or the shear layer. Test data to educe the impedance is acquired from measurements obtained in the NASA Langley Research Center Grazing Incidence Tube for mean flow Mach numbers ranging from 0.0 to 0.5 and source frequencies ranging from 0.5 kHz to 3.0 kHz. The unknown impedance of the liner b educed by judiciously choo~ingth e impedance via an optimization method to match the measured acoustic pressure on the wall opposite the test liner. Results are presented on four spatial grids using three different optimization methods (contour deformation, Davidon-Fletcher Powell, and the Genetic Algorithm). All three optimization methods converge to the same impedance when used with the same model and to nearly identical impedances when used on different models. h anomaly was observed only at 0.5 kHz for high mean flow speeds. The anomaly is likely due to the use of measured data in a flow regime where shear layer effects are important but are neglected in the math models. Consistency between the impedances educed using the two models provides confidence that the linearized Euler model is ready For application to more realistic flows, such as those containing shear layers.

Watson, Willie R.↗
NASA NTRS1995

Acoustic design of rotor blades using a genetic algorithm

A genetic algorithm coupled with a simplified acoustic analysis was used to generate low-noise rotor blade designs. The model includes thickness, steady loading and blade-vortex interaction noise estimates. The paper presents solutions for several variations in the fitness function, including thickness noise only, loading noise only, and combinations of the noise types. Preliminary results indicate that the analysis provides reasonable assessments of the noise produced, and that genetic algorithm successfully searches for "good" designs. The results show that, for a given required thrust coefficient, proper blade design can noticeably reduce the noise produced at some expense to the power requirements.

V. L. Wells↗
NASA NTRS2000

Mechanisms of the early phases of plant gravitropism

Gravitropism is directed growth of a plant or plant organ in response to gravity and can be divided into the following temporal sequence: perception, transduction, and response. This article is a review of the research on the early events of gravitropism (i.e., phenomena associated with the perception and transduction phases). The two major hypotheses for graviperception are the protoplast-pressure and starch-statolith models. While most researchers support the concept of statoliths, there are suggestions that plants have multiple mechanisms of perception. Evidence supports the hypothesis that the actin cytoskeleton is involved in graviperception/transduction, but the details of these mechanisms remain elusive. A number of recent developments, such as increased use of the molecular genetic approach, magnetophoresis, and laser ablation, have facilitated research in graviperception and have allowed for refinement of the current models. In addition, the entire continuum of acceleration forces from hypo- to hyper-gravity have been useful in studying perception mechanisms. Future interdisciplinary molecular approaches and the availability of sophisticated laboratories on the International Space Station should help to develop new insights into mechanisms of gravitropism in plants.

NASA Discipline Plant Biology↗
DOE OSTI2024

Intra- and inter-subtype HIV diversity between 1994 and 2018 in southern Uganda: a longitudinal population-based study

There is limited data on human immunodeficiency virus (HIV) evolutionary trends in African populations. We evaluated changes in HIV viral diversity and genetic divergence in southern Uganda over a 24-year period spanning the introduction and scale-up of HIV prevention and treatment programs using HIV sequence and survey data from the Rakai Community Cohort Study, an open longitudinal population-based HIV surveillance cohort. Gag (p24) and env (gp41) HIV data were generated from people living with HIV (PLHIV) in 31 inland semi-urban trading and agrarian communities (1994–2018) and four hyperendemic Lake Victoria fishing communities (2011–2018) under continuous surveillance. HIV subtype was assigned using the Recombination Identification Program with phylogenetic confirmation. Inter-subtype diversity was evaluated using the Shannon diversity index, and intra-subtype diversity with the nucleotide diversity and pairwise TN93 genetic distance. Genetic divergence was measured using root-to-tip distance and pairwise TN93 genetic distance analyses. Demographic history of HIV was inferred using a coalescent-based Bayesian Skygrid model. Evolutionary dynamics were assessed among demographic and behavioral population subgroups, including by migration status. 9931 HIV sequences were available from 4999 PLHIV, including 3060 and 1939 persons residing in inland and fishing communities, respectively. In inland communities, subtype A1 viruses proportionately increased from 14.3% in 1995 to 25.9% in 2017 (P < .001), while those of subtype D declined from 73.2% in 1995 to 28.2% in 2017 (P < .001). The proportion of viruses classified as recombinants significantly increased by nearly four-fold from 12.2% in 1995 to 44.8% in 2017. Inter-subtype HIV diversity has generally increased. While intra-subtype p24 genetic diversity and divergence leveled off after 2014, intra-subtype gp41 diversity, effective population size, and divergence increased through 2017. Intra- and inter-subtype viral diversity increased across all demographic and behavioral population subgroups, including among individuals with no recent migration history or extra-community sexual partners. This study provides insights into population-level HIV evolutionary dynamics following the scale-up of HIV prevention and treatment programs. Continued molecular surveillance may provide a better understanding of the dynamics driving population HIV evolution and yield important insights for epidemic control and vaccine development.

60 APPLIED LIFE SCIENCES↗
NASA NTRS2003

Role of genetic background in induced instability

Genomic instability is effectively induced by ionizing radiation. Recently, evidence has accumulated supporting a relationship between genetic background and the radiation-induced genomic instability phenotype. This is possibly due to alterations in proteins responsible for maintenance of genomic integrity or altered oxidative metabolism. Studies in human cell lines, human primary cells, and mouse models have been performed predominantly using high linear energy transfer (LET) radiation, or high doses of low LET radiation. The interplay between genetics, radiation response, and genomic instability has not been fully determined at low doses of low LET radiation. However, recent studies using low doses of low LET radiation suggest that the relationship between genetic background and radiation-induced genomic instability may be more complicated than these same relationships at high LET or high doses of low LET radiation. The complexity of this relationship at low doses of low LET radiation suggests that more of the population may be at risk than previously recognized and may have implications for radiation risk assessment.

NASA Discipline Radiation Health↗
NASA NTRS1991

Genetic algorithm based input selection for a neural network function approximator with applications to SSME health monitoring

A genetic algorithm is used to select the inputs to a neural network function approximator. In the application considered, modeling critical parameters of the space shuttle main engine (SSME), the functional relationship between measured parameters is unknown and complex. Furthermore, the number of possible input parameters is quite large. Many approaches have been used for input selection, but they are either subjective or do not consider the complex multivariate relationships between parameters. Due to the optimization and space searching capabilities of genetic algorithms they were employed to systematize the input selection process. The results suggest that the genetic algorithm can generate parameter lists of high quality without the explicit use of problem domain knowledge. Suggestions for improving the performance of the input selection process are also provided.

Peck, Charles C.↗
DOE OSTI2025

Tutorial: Machine-Learning-Based CREASE-2D Analysis of 2D SAXS Profiles to Characterize Anisotropic Nanostructures in Soft Materials

We present a tutorial to guide users on how to extend the Computational Reverse Engineering Analysis of Scattering Experiments-2D (CREASE-2D) framework to interpret their experimental two-dimensional small-angle scattering (SAS) data from soft materials (e.g., polymers, peptide amphiphiles, biomolecular fibrils). Unlike most traditional SAS analysis approaches, which typically rely on azimuthally averaged onedimensional (1D) profiles, CREASE-2D utilizes the complete 2D scattering profile to reveal information about anisotropy in the structure. In past applications, CREASE has provided insights into complex structural features, including the cross-sectional shapes of assembled nanostructures and dispersity in these features, which are difficult to discern with existing analytical models. While (1D- ) CREASE has been applied to SANS and SAXS data, this tutorial shares the steps for implementing CREASE-2D using an example of a dipeptide solution system, for which we have SAXS data. We present details for these steps involved in using CREASE-2D to interpret SAXS profiles: how to preprocess SAXS data, define relevant structural features, generate three-dimensional real-space structures for specific values of these features, train a machine learning (ML) surrogate model to predict scattering profiles for given structural features, and optimize these features using genetic algorithms (GA). Then, we use these steps to interpret complex 2DSAXS data collected from dipeptide solutions that, in microscopy images, exhibit nanoscale structures that could be elliptical tubes/ flat tapes/cylinders or a combination of these cross sections. Open-source codes, computational hardware, and software requirements, as well as the strengths and limitations of this protocol, are also presented. We expect researchers working with (soft) biomaterials, peptide amphiphiles, amphiphilic polymer solutions, polymer nanocomposites, and blends of particles/polymers will find this CREASE-2D method and this tutorial of use.

CREASE↗
NASA NTRS2000

Optimization of Microelectronic Devices for Sensor Applications

The NASA/JPL goal to reduce payload in future space missions while increasing mission capability demands miniaturization of active and passive sensors, analytical instruments and communication systems among others. Currently, typical system requirements include the detection of particular spectral lines, associated data processing, and communication of the acquired data to other systems. Advances in lithography and deposition methods result in more advanced devices for space application, while the sub-micron resolution currently available opens a vast design space. Though an experimental exploration of this widening design space-searching for optimized performance by repeated fabrication efforts-is unfeasible, it does motivate the development of reliable software design tools. These tools necessitate models based on fundamental physics and mathematics of the device to accurately model effects such as diffraction and scattering in opto-electronic devices, or bandstructure and scattering in heterostructure devices. The software tools must have convenient turn-around times and interfaces that allow effective usage. The first issue is addressed by the application of high-performance computers and the second by the development of graphical user interfaces driven by properly developed data structures. These tools can then be integrated into an optimization environment, and with the available memory capacity and computational speed of high performance parallel platforms, simulation of optimized components can proceed. In this paper, specific applications of the electromagnetic modeling of infrared filtering, as well as heterostructure device design will be presented using genetic algorithm global optimization methods.

Cwik, Tom↗
NASA NTRS2005

Multidisciplinary Multiobjective Optimal Design for Turbomachinery Using Evolutionary Algorithm

This report summarizes Dr. Lian s efforts toward developing a robust and efficient tool for multidisciplinary and multi-objective optimal design for turbomachinery using evolutionary algorithms. This work consisted of two stages. The first stage (from July 2003 to June 2004) Dr. Lian focused on building essential capabilities required for the project. More specifically, Dr. Lian worked on two subjects: an enhanced genetic algorithm (GA) and an integrated optimization system with a GA and a surrogate model. The second stage (from July 2004 to February 2005) Dr. Lian formulated aerodynamic optimization and structural optimization into a multi-objective optimization problem and performed multidisciplinary and multi-objective optimizations on a transonic compressor blade based on the proposed model. Dr. Lian s numerical results showed that the proposed approach can effectively reduce the blade weight and increase the stage pressure ratio in an efficient manner. In addition, the new design was structurally safer than the original design. Five conference papers and three journal papers were published on this topic by Dr. Lian.

Source record↗
NASA NTRS1996

Optimization of Operations Resources via Discrete Event Simulation Modeling

The resource levels required for operation and support of reusable launch vehicles are typically defined through discrete event simulation modeling. Minimizing these resources constitutes an optimization problem involving discrete variables and simulation. Conventional approaches to solve such optimization problems involving integer valued decision variables are the pattern search and statistical methods. However, in a simulation environment that is characterized by search spaces of unknown topology and stochastic measures, these optimization approaches often prove inadequate. In this paper, we have explored the applicability of genetic algorithms to the simulation domain. Genetic algorithms provide a robust search strategy that does not require continuity and differentiability of the problem domain. The genetic algorithm successfully minimized the operation and support activities for a space vehicle, through a discrete event simulation model. The practical issues associated with simulation optimization, such as stochastic variables and constraints, were also taken into consideration.

Joshi, B.↗
DOE OSTI2024

Stress intensity factor models using mechanics-guided decomposition and symbolic regression

The finite element method can be used to compute accurate stress intensity factors (SIFs) for cracks with complex geometries and boundary conditions. In contrast, handbook solutions act as surrogate SIF models that provide significantly faster evaluation times. However, the development of conventional surrogate SIF models relies on manual development based on low-order parameterizations. This limits surrogate model accuracy and generalizability. Here, in this paper, we develop a framework for the automated development of mechanics-guided handbook SIF solutions by using interpretable machine learning via genetic programming for symbolic regression (GPSR). Formalizing the mechanics-based approach of Raju and Newman, SIF training data is decomposed into multiple subsets. This decomposition enables parallel GPSR model development of subfunctions, each of which accounts for specific geometrical corrections with respect to a known analytical model. Using this mechanics-based approach with GPSR allows for equations to be learned with improved accuracy and reduced complexity relative to the Raju Newman equations while maintaining the inherent interpretability of mathematical expressions. In this paper, we present equations that match the complexity of the Raju Newman equations while having reduced error, as well as equations with similar errors and reduced complexity.

42 ENGINEERING↗
DOE OSTI2024

Constitutive model development of aluminum alloy 1100 for elevated temperature forming process

Commercially pure aluminum alloy, AA1100, presents good electrical and thermal conductivity, high formability, and low cost. Those favorable characteristics have the potential to enable bipolar plates with improved economics and enhanced performance compared to current stainless steel bipolar plates for proton exchange membrane fuel cells. An accurate constitutive model is essential to develop and optimize processing parameters and effectively control the forming process. Here, the objective of this work is to develop a constitutive model of AA1100 that is able to simulate stress-strain relation, formed geometry, and predict the onset of fracture strain to avoid forming failure. Initially, a set of tensile tests at temperature between 300 and 500°C and strain rate between 0.005 and 1.0/s were conducted to examine the deformation behavior. Then, a set of damage-based unified visco-plastic constitutive equations is proposed and calibrated based on the results of stress-strain data. A genetic algorithm optimization method is applied to search for best fitting material constants in constitutive equations. The proposed model shows good predictability of both the stress-strain relation and fracture strain at low strain rate and high temperature conditions. The accuracy of proposed model is also evaluated statistically. A comparison of the proposed model with three popular models (Arrhenius-type mode, Johnson-Cook model and Zerilli-Armstrong model) was made. The proposed model shows the best experimental agreement with correlation coefficient of 0.96 in contrast to 0.25, 0.38 and 0.75 for the popular models, respectively. The proposed model can help to optimize the elevated temperature forming process and guide die design to enable optimal geometric features in the formed components.

08 HYDROGEN↗
NASA NTRS2019

Evaluating Effects of Altered Gravity on the Nervous System Using D. melanogaster

A comprehensive understanding of the effects of spaceflight and altered gravity on human physiology is necessary for continued human space exploration and long-term space habitation. The oxidative stress response has been identified in astronauts exposed to short- and long-term space missions that are exposed to the multitude of stress factors of spaceflight, including altered gravity and radiation exposure. Reactive oxygen species (ROS) are byproducts of homeostatic cellular metabolism, yet when overproduced the oxidative stress response ensues, rendering molecules destructive causing cell death and inflammation. Controlling aberrant ROS production is necessary to prevent pathological consequences, in particular within the nervous system, since neurons are extremely sensitive overexpressed ROS insults. We hypothesize that exposure to altered gravity triggers the oxidative stress response, leading to impairments in the nervous system. In this study, we used a well-established spaceflight model organism, Drosophila melanogaster, to assess altered gravity associated changes in the nervous system using a ground-based hypergravity model. Acute hypergravity resulted in an induction of oxidative stress-related genes with an increase in reactive oxygen species (ROS) in fly brains (p<0.001). Also, qPCR analysis shows that parkin gene expression is significantly reduced in these fly brains(p<0.05). Additionally, chronic hypergravity resulted in depressed locomotor phenotype in these flies (p<0.05) in conjunction to decreased dopaminergic neuron counts (p<0.0001) and increased apoptosis in these fly brains (p<0.0001). Further, assessment of neurological changes, including the neuronal architecture, synaptic integrity and genetic regulation caused by hypergravity conditions were noted. Overall, our results validate chronic hypergravity simulation as a behavioral model to study spaceflight effects, and oxidative stress pathway as a potential avenue for countermeasure development for astronauts undergoing short- and long-term missions and for neurodegenerative research on Earth.

Mhatre, Siddhita↗
NASA NTRS2001

Actuator Placement Via Genetic Algorithm for Aircraft Morphing

This research continued work that began under the support of NASA Grant NAG1-2119. The focus of this effort was to continue investigations of Genetic Algorithm (GA) approaches that could be used to solve an actuator placement problem by treating this as a discrete optimization problem. In these efforts, the actuators are assumed to be "smart" devices that change the aerodynamic shape of an aircraft wing to alter the flow past the wing, and, as a result, provide aerodynamic moments that could provide flight control. The earlier work investigated issued for the problem statement, developed the appropriate actuator modeling, recognized the importance of symmetry for this problem, modified the aerodynamic analysis routine for more efficient use with the genetic algorithm, and began a problem size study to measure the impact of increasing problem complexity. The research discussed in this final summary further investigated the problem statement to provide a "combined moment" problem statement to simultaneously address roll, pitch and yaw. Investigations of problem size using this new problem statement provided insight into performance of the GA as the number of possible actuator locations increased. Where previous investigations utilized a simple wing model to develop the GA approach for actuator placement, this research culminated with application of the GA approach to a high-altitude unmanned aerial vehicle concept to demonstrate that the approach is valid for an aircraft configuration.

Crossley, William A.↗
DOE OSTI2025

The unique architecture of umbrella toxins permits a two-tiered molecular bet-hedging strategy for interbacterial antagonism

Bacteria exist in competitive and rapidly changing environments in which the nature of future threats cannot be easily predicted. Streptomyces coelicolor produces three antibacterial umbrella particles that harbor distinct polymorphic toxin domains and an overlapping set of six diversified lectins. Here, we show that the exquisite specificity of umbrella particles derives from lectin-mediated species-specific binding to previously undescribed hypervariable surface glycoconjugates. A cryo-electron microscopy (cryo-EM) structure of one such lectin in complex with its oligosaccharide substrate defines the molecular basis for targeting through the coordinated recognition of multiple glycan features. Biochemical and genetic studies of several target species, in conjunction with lectin-swapping experiments, support a model whereby S. coelicolor umbrella toxin diversification at the levels of lectin composition and toxin polymorphism represents a unique, two-tiered bet-hedging strategy. Bioinformatic analyses support this as a means by which the unusual architecture of umbrella toxins offers Streptomyces a generalizable strategy to antagonize an unpredictable array of competitors.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Nonlinear thermodynamic computing out of equilibrium

We present the design for a thermodynamic computer that can perform arbitrary nonlinear calculations in or out of equilibrium. Simple thermodynamic circuits, fluctuating degrees of freedom in contact with a thermal bath and confined by a quartic potential, display an activity that is a nonlinear function of their input. Such circuits can therefore be regarded as thermodynamic neurons, and can serve as the building blocks of networked structures that act as thermodynamic neural networks, universal function approximators whose operation is powered by thermal fluctuations. We simulate a digital model of a thermodynamic neural network, and show that its parameters can be adjusted by genetic algorithm to perform nonlinear calculations at specified observation times, regardless of whether the system has attained thermal equilibrium. This work expands the field of thermodynamic computing beyond the regime of thermal equilibrium, enabling fully nonlinear computations, analogous to those performed by classical neural networks, at specified observation times.

Whitelam, Stephen [Lawrence Berkeley National Labo↗