Search NASA⌕ Search

SEARCH · Search NASA

Results for “Navier Stokes simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Aerothermodynamic Design of the Mars Science Laboratory Backshell and Parachute Cone

Aerothermodynamic design environments are presented for the Mars Science Laboratory entry capsule backshell and parachute cone. The design conditions are based on Navier-Stokes flowfield simulations on shallow (maximum total heat load) and steep (maximum heat flux) design entry trajectories from a 2009 launch. Transient interference effects from reaction control system thruster plumes were included in the design environments when necessary. The limiting backshell design heating conditions of 6.3 W/sq cm for heat flux and 377 J/sq cm for total heat load are not influenced by thruster firings. Similarly, the thrusters do not affect the parachute cover lid design environments (13 W/sq cm and 499 J/sq cm). If thruster jet firings occur near peak dynamic pressure, they will augment the design environments at the interface between the backshell and parachute cone (7 W/sq cm and 174 J/sq cm). Localized heat fluxes are higher near the thruster fairing during jet firings, but these areas did not require additional thermal protection material. Finally, heating bump factors were developed for antenna radomes on the parachute cone

Edquist, Karl T.↗

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Fail-safe, hybrid, flow control (HFC) is a promising technology for meeting high-speed cruise efficiency, low-noise signature, and reduced fuel-burn goals for future, Hybrid-Wing-Body (HWB) aircraft with embedded engines. This report details the development of HFC technology that enables improved inlet performance in HWB vehicles with highly integrated inlets and embedded engines without adversely affecting vehicle performance. In addition, new test techniques for evaluating Boundary-Layer-Ingesting (BLI)-inlet flow-control technologies developed and demonstrated through this program are documented, including the ability to generate a BLI-like inlet-entrance flow in a direct-connect, wind-tunnel facility, as well as, the use of D-optimal, statistically designed experiments to optimize test efficiency and enable interpretation of results. Validated improvements in numerical analysis tools and methods accomplished through this program are also documented, including Reynolds-Averaged Navier-Stokes CFD simulations of steady-state flow physics for baseline, BLI-inlet diffuser flow, as well as, that created by flow-control devices. Finally, numerical methods were employed in a ground-breaking attempt to directly simulate dynamic distortion. The advances in inlet technologies and prediction tools will help to meet and exceed "N+2" project goals for future HWB aircraft.

McMillan, Michelle L.↗

Computational Analyses of the LIMX TBCC Inlet High-Speed Flowpath

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for the high-speed flowpath and isolator of a dual-flowpath Turbine-Based Combined-Cycle (TBCC) inlet using the Wind-US code. The RANS simulations were performed in preparation for the Large-scale Inlet for Mode Transition (LIMX) model tests in the NASA Glenn Research Center (GRC) 10- by 10-ft Supersonic Wind Tunnel. The LIMX inlet has a low-speed flowpath that is coupled to a turbine engine and a high-speed flowpath designed to be coupled to a Dual-Mode Scramjet (DMSJ) combustor. These RANS simulations were conducted at a simulated freestream Mach number of 4.0, which is the nominal Mach number for the planned wind tunnel testing with the LIMX model. For the simulation results presented in this paper, the back pressure, cowl angles, and freestream Mach number were each varied to assess the performance and robustness of the high-speed inlet and isolator. Under simulated wind tunnel conditions at maximum inlet mass flow rates, the high-speed flowpath pressure rise was found to be greater than a factor of four. Furthermore, at a simulated freestream Mach number of 4.0, the high-speed flowpath and isolator showed stability for freestream Mach number that drops 0.1 Mach below the design point. The RANS simulations indicate the yet-untested highspeed inlet and isolator flowpath should operate as designed. The RANS simulation results also provided important insight to researchers as they developed test plans for the LIMX experiment in GRC s 10- by 10-ft Supersonic Wind Tunnel.

Dippold, Vance F., III↗

Drag Reduction Through Distributed Electric Propulsion

One promising application of recent advances in electric aircraft propulsion technologies is a blown wing realized through the placement of a number of electric motors driving individual tractor propellers spaced along each wing. This configuration increases the maximum lift coefficient by providing substantially increased dynamic pressure across the wing at low speeds. This allows for a wing sized near the ideal area for maximum range at cruise conditions, imparting the cruise drag and ride quality benefits of this smaller wing size without decreasing takeoff and landing performance. A reference four-seat general aviation aircraft was chosen as an exemplary application case. Idealized momentum theory relations were derived to investigate tradeoffs in various design variables. Navier-Stokes aeropropulsive simulations were performed with various wing and propeller configurations at takeoff and landing conditions to provide insight into the effect of different wing and propeller designs on the realizable effective maximum lift coefficient. Similar analyses were performed at the cruise condition to ensure that drag targets are attainable. Results indicate that this configuration shows great promise to drastically improve the efficiency of small aircraft.

Stoll, Alex M.↗

Optimal Shape Design of Mail-Slot Nacelle on N3-X Hybrid Wing-Body Configuration

System studies show that a N3-X hybrid wing-body aircraft with a turboelectric distributed propulsion system using a mail-slot inlet/nozzle nacelle can meet the environmental and performance goals for N+3 generation transports (three generations beyond the current air transport technology level) set by NASA's Subsonic Fixed Wing Project. In this study, a Navier-Stokes flow simulation of N3-X on hybrid unstructured meshes was conducted, including the mail-slot propulsor. The geometry of the mail-slot propulsor was generated by a CAD (Computer-Aided Design)-free shape parameterization. A novel body force model generation approach was suggested for a more realistic and efficient simulation of the flow turning, pressure rise and loss effects of the fan blades and the inlet-fan interactions. Flow simulation results of the N3-X demonstrates the validity of the present approach. An optimal Shape design of the mail-slot nacelle surface was conducted to reduce strength of shock waves and flow separations on the cowl surface.

Kim, Hyoungjin↗

Analysis of Low-Speed Stall Aerodynamics of a Swept Wing with Seamless Flaps

Computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a Gulfstream G-III airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) swept wing modified with an experimental seamless, compliant flap called the Adaptive Compliant Trailing Edge (ACTE) flap. The stall characteristics of the modified ACTE wing were analyzed and compared with the unmodified, clean wing at the flight speed of 120 knots and altitude of 2300 feet above mean sea level, in free air as well as in ground effect. A polyhedral finite-volume unstructured full Navier-Stokes CFD code, STAR-CCM (registered trademark) plus (CD-adapco [Computational Dynamics Limited, United Kingdom, and Analysis & Design Application Co., United States]), was used. Steady Reynolds-averaged Navier-Stokes CFD simulations were conducted for a clean wing and the ACTE wings at various ACTE deflection angles in free air (-2 degrees, 15 degrees, and 30 degrees) as well as in ground effect (15 degrees and 30 degrees). Solution sensitivities to grid densities were examined. In free air, the ACTE wings are predicted to stall at lower angles of attack than the clean wing. In ground effect, all wings are predicted to stall at lower angles of attack than the corresponding wings in free air. Even though the lift curves are higher in ground effect than in free air, the maximum lift coefficients for all wings are lower in ground effect. Finally, the lift increase due to ground effect for the ACTE wing is predicted to be less than the clean wing.

CFD↗

Design and Analyses of High Aspect Ratio Nozzles for Distributed Propulsion Acoustic Measurements

A series of three convergent, round-to-rectangular high aspect ratio (HAR) nozzles were designed for acoustic testing at the NASA Glenn Research Center Nozzle Acoustic Test Rig (NATR). The HAR nozzles had exit area aspect ratios of 8:1, 12:1, and 16:1. The nozzles were designed to mimic a distributed propulsion system array with a slot nozzle. The nozzle designs were screened using Reynolds-Averaged Navier-Stokes (RANS) simulations. In addition to meeting the geometric constraints required for testing in the NATR, the HAR nozzles were designed to be free of flow features that would produce unwanted noise (e.g., flow separations) and to have uniform flow at the nozzle exit. Multiple methods were used to generate HAR nozzle designs. The final HAR nozzle designs were generated in segments using a computer code that parameterized each segment. RANS screening simulations showed that intermediate nozzle designs suffered flow separation, a normal shockwave at the nozzle exit (caused by an aerodynamic throat produced by boundary layer growth), and non-uniform flow at the nozzle exit. The RANS simulations showed that the final HAR nozzle designs were free of flow separations, but were not entirely successful at producing a fully uniform flow at the nozzle exit. The final designs suffered a pair of counter-rotating vortices along the outboard walls of the nozzle. The 16:1 aspect ratio HAR nozzle had the least uniform flow at the exit plane; the 8:1 aspect ratio HAR nozzles had a fairly uniform flow at the nozzle exit plane.

acoustic measure↗

What Was Learned in Predicting Slender Airframe Aerodynamics with the F-16XL Aircraft

The second Cranked-Arrow Wing Aerodynamics Project, International, coordinated project has been underway to improve high-fidelity computational-fluid-dynamics predictions of slender airframe aerodynamics. The work is focused on two flow conditions and leverages a unique flight data set obtained with the F-16XL aircraft for comparison and validation. These conditions, a low-speed high-angle-of-attack case and a transonic low-angle-of-attack case, were selected from a prior prediction campaign wherein the computational fluid dynamics failed to provide acceptable results. In revisiting these two cases, approaches for improved results include better, denser grids using more grid adaptation to local flow features as well as unsteady higher-fidelity physical modeling like hybrid Reynolds-averaged Navier-Stokes/unsteady Reynolds-averaged Navier-Stokes/large-eddy simulation methods. The work embodies predictions from multiple numerical formulations that are contributed from multiple organizations where some authors investigate other possible factors that could explain the discrepancies in agreement (e.g., effects due to deflected control surfaces during the flight tests as well as static aeroelastic deflection of the outer wing). This paper presents the synthesis of all the results and findings and draws some conclusions that lead to an improved understanding of the underlying flow physics, finally making the connections between the physics and aircraft features.

Rizzi, Arthur↗

Preliminary Soot Computations Based on a Model Aircraft Combustor With OpenNCC

In a preliminary effort to extend our current capabilities used in the design & testing of aero-engine combustors to particulate emissions, we incorporated several existing 2- equation soot models into the Open National Combustion Code (OpenNCC). The paper presents results from a validation study based on a well-characterized, swirl-stabilized, turbulent sooting flame generated by a model aero-engine combustor developed at DLR, Germany. The calculations are based on a Reynolds-Averaged Navier Stokes (RANS) simulation with standard k-e turbulence model & a finite-rate chemical kinetic mechanism. A separate transport equation is solved for all individual species involved in ethylene/air combustion. The predicted velocity and temperature are mostly in good agreement with the measured data and reasonable agreement was found for soot. While the calculated SVF (Soot Volume Fraction) behavior is similar to some other predicted results reported in literature, the measured soot lasts farther downstream than the calculated soot indicating a need for further improvement in the soot models employed.

Raju, Manthena↗

CFD Predictions of Soot & CO Emissions Generated by a Partially-Fueled 9-Element Lean-Direct Injection Combustor

A study was undertaken to investigate the CO & soot emissions generated by a partially-fueled 9- element LDI (Lean-Direct Injection) combustor configuration operating in the idle range of jet engine conditions. In order to perform the CFD analysis, several existing soot/chemistry models were implemented into the OpenNCC (Open National Combustion Code). The calculations were based on a Reynolds-Averaged Navier Stokes (RANS) simulation with standard k-epsilon turbulence model, a 62- species jet-a/air chemistry, a 2-equation soot model, & a Lagrangian spray solver. A separate transport equation was solved for all individual species involved in jet-a/air combustion. In the test LDI configuration we examined, only five of the nine injectors were fueled with the major pilot injector operating at an equivalence ratio of near one and the other four main injectors operating at an equivalence ratio near 0.55. The calculations helped to identify several reasons behind the soot & CO formation in different regions of the combustor. The predicted results were compared with the reported experimental data on soot mass concentration (SMC) & emissions index of CO (EICO). The experimental results showed that an increase in either T3 and/or F/A ratio lead to a reduction in both EICO & SMC. The predicted results were found to be in reasonable agreement. However, the predicted EICO differed substantially in one test condition associated with higher F/A ratio.

Raju, M. S.↗

Comparison of Boundary Layer Similarity Transformations for High Mach Number Flows

Reynolds averaged Navier-Stokes (RANS) simulations of the turbulent boundary layer flow on a flat plate are performed across a Mach number range of 0.3 up to 16 using the computational fluid dynamics (CFD) software, VULCAN-CFD. The simulation results are used to evaluate the ability of the Van Driest transformation and the transformation of Trettel and Larsson to collapse boundary layer velocity profiles under various flow conditions across the range of Mach numbers. The flat platewall boundary conditions and leading edge geometry are varied from adiabatic to isothermal and sharp to blunted to reveal the physics of how these effects impact the performance of the chosen flow transformations. Results indicate that the transformation of Trettel and Larsson produces a better collapse of velocity profile data than the Van Driest transformation regardless of Mach number, wall boundary condition, or leading edge geometry. In addition, the velocity gradients obtained from the transformation of Trettel and Larsson match the normalized untransformed velocity gradients much more closely than those obtained using the Van Driest transformation.

DiGregorio, Nicholas J.↗

Prediction of Turbulent Diffusing Flows Using FUN3D

The FUN3D code was used to perform Reynolds-averaged Navier-Stokes (RANS) simulations to compute subsonic flow in an S-duct diffuser and transonic flow in a two-dimensional diffuser using the Speziale-Sarkar-Gatski/Launder-Rodi-Reece (SSG/LRR) Reynolds stress model (RSM). For comparison purposes, additional simulations were run with the one-equation Spalart-Allmaras (SA) and the two-equation Menter Shear-Stress Transport (SST) turbulence models. Each model was run with and without the quadratic constitutive relation (QCR) for computing the turbulent stresses. It was shown that the simulations that utilized the RSM had better overall predictions of the diffusive flow fields compared to the simulations that utilized the one and two equation turbulence models.

Inlet Distortion↗

Prediction of Turbulent Diffusing Flows Using FUN3D

The FUN3D code was used to perform Reynolds-averaged Navier-Stokes (RANS) simulations to compute subsonic flow in an S-duct diffuser and transonic flow in a two-dimensional diffuser using the Speziale-Sarkar-Gatski/Launder-Rodi-Reece (SSG/LRR) Reynolds stress model (RSM). For comparison purposes, additional simulations were run with the one-equation Spalart-Allmaras (SA) and the two-equation Menter Shear-Stress Transport (SST) turbulence models. Each model was run with and without the quadratic constitutive relation (QCR) for computing the turbulent stresses. It was shown that the simulations that utilized the RSM had better overall predictions of the diffusive flow fields compared to the simulations that utilized the one and two equation turbulence models.

Inlet Distortion↗

Validation of Actuator Disk, Actuator Line and Sliding Mesh Methods within the LAVA Solver

In this study the implementation of actuator-disk, actuator-line and sliding-mesh methodologies in the Launch Ascent and Vehicle Aerodynamics (LAVA) solver is described and validated against several test-cases. The different models are validated against available numerical as well as experimental data. Both steady and unsteady Reynolds-Averaged Navier-Stokes (RANS) simulations using the Spallart Allmaras (SA) turbulence model are performed for several different configurations representative of aeroscience applications. The first part of the paper is focused on the verification and validation of the implemented propulsor models. The first validation case is a theoretical rotor in hover, compared with the 1D analytical solution derived from momentum theory. The second validation is the Rotor-Airframe Interaction Model of Georgia Institute of Technology (GIT), representing the application of actuator disks to top-mounted rotorcraft vehicles or unmanned aerial vehicles (UAVs). The third case is a representative configuration for tip-mounted rotor-craft vehicles such as NASA’s X57 airplane. The second part of the paper shows the implemented models applied to realistic engineering configurations such as NASA’s X57 airplane and the R4 Advanced Ducted Propellor (ADT). A modification to the actuator line method in order to represent the blade geometry more closely is proposed and comparisons with simulations modeling the blade utilizing a sliding-mesh approach are made.

ARMD↗

Exploring the Langtry-Menter Transition Model for High Speed Applications Using FUN3D

A series of Reynolds-averaged Navier-Stokes (RANS) simulations were performed using the FUN3D flow solver to explore the capabilities of the Langtry-Menter Shear-Stress Transport (LM-SST) transition model for predicting transition for aircraft inlet applications. Two geometries were simulated: a zero-pressure-gradient flat plate and an axisymmetric cone exposed to hypersonic flow. In addition to the transition-sensitized LM-SST model investigations, simulations were run with the one-equation Spalart-Allmaras (SA) and the two-equation Menter Shear-Stress Transport (SST-V) RANS models in fully turbulent mode to identify the natural RANS model transition behavior as a function of Mach number when executed in fully turbulent mode. The flat plate simulations showed that (1) the transition model was able to predict rapid transition at a freestream Mach number of 0.2, which is expected but (2) the predicted transition location moved downstream as the freestream Mach number was increased for the simulations that used the SST-V turbulence model. The latter is significant as it is usually assumed that one- and two-equation turbulence models will produce fully turbulent flow very near the boundary layer origin. The flat plate simulation freestream Mach number trend was confirmed with simulations using the Wind-US code, which also saw a similar trend when employing the SA turbulence model. For the axisymmetric cone simulations, the transition location was highly sensitive to the inflow turbulence levels. This is significant as the prediction of the transition location is crucial when trying to predict inlet performance, especially for hypersonic vehicle applications. It was also noted that the predicted transition location for the cone when using the SST-V turbulence model agreed well with the predicted transition location from the equivalent zero-pressure-gradient flat plate case.

Transition Model↗

Acoustics of a Supersonic Mach 1.4 Axisymmetric Spike Inlet

An engine inlet for a supersonic commercial aircraft is analyzed for noise radiation in low-speed configurations for which auxiliary inlet doors are open. Duct modes generated by the fan are estimated by post-processing unsteady Reynold averaged Navier-Stokes (URANS) simulations of the fan and are used as boundary conditions to the inlet domain. Far-field inlet radiated tone levels are computed using commercial acoustics finite element software. The results indicated that the inlet tone levels at cutback and sideline conditions are higher by more than 20 dB than the approach levels.

Supersonics↗

Exploring the Langtry-Menter Transition Model for High Speed Applications Using FUN3D

A series of Reynolds-averaged Navier-Stokes (RANS) simulations were performed using the FUN3D flow solver to explore the capabilities of the Langtry-Menter Shear-Stress Transport (LM-SST) transition model for predicting transition for aircraft inlet applications. Two geometries were simulated: a zeropressure-gradient flat plate and an axisymmetric cone exposed to hypersonic flow. In addition to the transition-sensitized LM-SST model investigations, simulations were run with the one-equation SpalartAllmaras (SA) and the two-equation Menter Shear-Stress Transport (SST-V) RANS models in fully turbulent mode to identify the natural RANS model transition behavior as a function of Mach number when executed in fully turbulent mode. The flat plate simulations showed that (1) the transition model was able to predict rapid transition at a freestream Mach number of 0.2, which is expected but (2) the predicted transition location moved downstream as the freestream Mach number was increased for the simulations that used the SST-V turbulence model. The latter is significant as it is usually assumed that one- and two-equation turbulence models will produce fully turbulent flow very near the boundary layer origin. The flat plate simulation freestream Mach number trend was confirmed with simulations using the Wind-US code, which also saw a similar trend when employing the SA turbulence model. For the axisymmetric cone simulations, the transition location was highly sensitive to the inflow turbulence levels. This is significant as the prediction of the transition location is crucial when trying to predict inlet performance, especially for hypersonic vehicle applications. It was also noted that the predicted transition location for the cone when using the SST-V turbulence model agreed well with the predicted transition location from the equivalent zero-pressure-gradient cold wall flat plate case.

Transition Model↗

Aeroheating Environments of Aerocapture Systems for Uranus Orbiters

Aeroheating environments for an aerocapture system enabling flagship-class science at Uranus are presented. Applicability of a low lift-to-drag entry vehicle aeroshell with flight heritage for Martian entries is considered in the context of an end-to-end Uranus orbiter and probe mission design using aerocapture for orbit insertion. A feasible trajectory space for aerocapture orbit insertion based on various launch opportunities and interplanetary trajectories yield atmosphere-relative entry velocities between 22 km/s and 31 km/s with maximum freestream densities on the order of 10−5 kg/m3. A preliminary study of the aerothermal environments for the entire trajectory space is discussed followed by a more detailed study of the nominal design trajectories. Design conditions are based on laminar, thermochemical nonequilibrium Navier-Stokes flowfield simulations with coupled radiation transport for full lift-up (deep) and lift-down (shallow) design trajectories. Convective heating is found to be the dominant heating mode, with radiation accounting for only 1 % to 5 % of the total heat flux for the design trajectories. The peak design conditions are found to be 422 W/cm2 for heat flux, 10.5 kPa for pressure, 149 Pa for shear stress, and 88.1 kJ/cm2 for the total heat load.

Uranus↗