SEARCH · Search NASA

Results for “Permitting process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Fabrication of structural elements

The laminate fabrication procedures and quality assurance ultrasonic C-scan results used for structural elements are described. These procedures are the result of processing eleven lots of graphite/PMR-15 prepreg tape materials and two lots of graphite/NR-150B2. Early processing difficulties with NR-150B2 composites were corrected, permitting the fabrication of quality specimens from either of the two currently prescribed matrix materials. The quality of all deliverable specimens is measured by the control of fiber content, glass transition temperature, and void content, as well as laminate ultrasonic C-scan data.

Darms, F. J., Jr.↗

NASA NTRS1985

Ritz Procedure for COSMIC/NASTRAN

An analysis procedure has been developed and incorporated into COSMIC/NASTRAN that permits large dynamic degree of freedom models to be processed accurately with little or no extra effort required by the user. The method employs existing capabilities without the need for approximate Guyan reduction techniques. Comparisons to existing solution procedures presently within NASTRAN are discussed.

Citerley, R. L.↗

NASA NTRS1988

Fatique crack growth behavior of a single crystal alloy as observed through an in situ fatigue loading stage

An in situ fatigue loading stage inside a scanning electron microscope (SEM) was used to determine the fatigue crack growth behavior of a PWA 1480 single-crystal nickel-based superalloy. The loading stage permits real-time viewing of the fatigue damage processes at high magnification. The PWA 1480 single-crystal, single-edge notch specimens were tested with the load axis parallel to the (100) orientation. Two distinct fatigue failure mechanisms were identified. The crack growth rate differed substantially when the failure occurred on a single slip system in comparison to multislip system failure. Two processes by which crack branching is produced were identified and are discussed. Also discussed are the observed crack closure mechanisms.

Telesman, Jack↗

NASA NTRS1988

Fatigue crack growth behavior of a single crystal alloy as observed through an in situ fatigue loading stage

Telesman, Jack↗

NASA NTRS1991

The application of statistically designed experiments to resistance spot welding

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit realtime monitoring of operations through advances in computerized process control. In order to realize adaptive feedback capabilities, it is necessary to establish correlations among process variables, welder outputs, and weldment properties. The initial step toward achieving this goal must involve assessment of the effect of specific process inputs and the interactions among these variables on spot weld characteristics. This investigation evaluated these effects through the application of a statistically designed experiment to the RSW process. A half-factorial, Taguchi L sub 16 design was used to understand and refine a RSW schedule developed for welding dissimilar aluminum-lithium alloys of different thickness. The baseline schedule had been established previously by traditional trial and error methods based on engineering judgment and one-factor-at-a-time studies. A hierarchy of inputs with respect to each other was established, and the significance of these inputs with respect to experimental noise was determined. Useful insight was gained into the effect of interactions among process variables, particularly with respect to weldment defects. The effects of equipment related changes associated with disassembly and recalibration were also identified. In spite of an apparent decrease in equipment performance, a significant improvement in the maximum strength for defect-free welds compared to the baseline schedule was achieved.

Hafley, Robert A.↗

NASA NTRS1991

Energy stability of thermocapillary convection in a model of the float-zone crystal-growth process. II - Nonaxisymmetric disturbances

Energy-stability theory has been applied to investigate the stability properties of thermocapillary convection in a half-zone model of the float-zone crystal-growth process. An earlier axisymmetric model has been extended to permit nonaxisymmetric disturbances, thus determining sufficient conditions for stability to disturbances of arbitrary amplitude. The results for nonaxisymmetric disturbances are compared with earlier axisymmetric results, with linear-stability results for a geometry with an infinitely long aspect ratio and with stability boundaries from recent laboratory experiments.

Neitzel, G. P.↗

NASA NTRS1993

Eliminating LH2 in LOX-collect space launchers - Key to on-demand capability

Two air-breathing reusable two-stage space launch vehicle concepts are proposed, in which the first stage employs turboramjet propulsion and the second stage uses rockets, which are expected to provide very rapid response launch of 10,000 lb polar-orbit payloads. In both concepts, liquid oxygen (LOX) for the second stage is collected during first stage ascent, thus eliminating the need for LOX ground servicing facilities. In the first concept, liquid hydrogen in the amount just sufficient to condense and collect second state LOX is the only cryogenic fluid that is loaded on the vehicle at takeoff. The second concept uses the heat sink of conventional jet propulsion fuel and water coolant to drive a lightweight adaptation of the commercial LOX production process, eliminating all cryogenics at takeoff. Both concepts should permit true launch-on-demand capability with aircraftlike ground operations.

Leingang, J. L.↗

NASA NTRS1990

Vehicle processing operations database

The Vehicle Processing Operations Data base (VPOD) has been designed and constructed to enable the collection and preliminary analysis of data relative to the processing of planetary exploration vehicles in low Earth orbit. VPOD has the capability to hierarchically store the events, assemblies, and equipment data needed for performing vehicle processing analysis, to whatever level of detail available. This permits some analysis to be performed even during the very early phases of vehicle and mission design. As more data about the events, assemblies, or equipment become available, the analysis can then be refined using the increased level of detail. VPOD output is based on a mission defined by selecting from the VPOD Events data base the events that are required to perform the desired tasks. The outputs available include total crew time, crew skill requirements, equipment needed, assemblies worked per event, to any available level of detail. The VPOD design is structured to interface with an operations simulation capability which is currently in the requirements definition phase. The simulator will use information from the VPOD to perform operations analysis for missions being conducted in low Earth orbit. VPOD information, along with information from the science missions operations data base and a Space Station configuration data base, will be used by the simulator to provide a capability to study total system operations and resources requirements.

Ganoe, George G.↗

NASA NTRS1993

Odyssey personal communications satellite system

The spectacular growth of cellular telephone networks has proved the demand for personal communications. Large regions of the world are too sparsely populated to be economically served by terrestrial cellular communications. Since satellites are well suited to this application, TRW filed with the FCC on May 31, 1993 for the Odyssey construction permit. Odyssey will provide high quality wireless communication services worldwide from satellites. These services will include: voice, data, paging, and messaging. Odyssey will be an economical approach to providing communications. A constellation of 12 satellites will be orbited in three, 55 deg. inclined planes at an altitude of 10,354 km to provide continuous coverage of designated regions. Two satellites will be visible anywhere in the world at all times. This dual visibility leads to high line-of-sight elevation angles, minimizing obstructions by terrain, trees and buildings. Each satellite generates a multibeam antenna pattern that divides its coverage area into a set of contiguous cells. The communications system employs spread spectrum CDMA on both the uplinks and downlinks. This signaling method permits band sharing with other systems and applications. Signal processing is accomplished on the ground at the satellite's 'Gateway' stations. The 'bent pipe' transponders accommodates different regional standards, as well as signaling changes over time. The low power Odyssey handset will be cellular compatible. Multipath fade protection is provided in the handset.

Spitzer, Christopher J.↗

NASA NTRS1999

Integration of vestibular and head movement signals in the vestibular nuclei during whole-body rotation

Single-unit recordings were obtained from 107 horizontal semicircular canal-related central vestibular neurons in three alert squirrel monkeys during passive sinusoidal whole-body rotation (WBR) while the head was free to move in the yaw plane (2.3 Hz, 20 degrees /s). Most of the units were identified as secondary vestibular neurons by electrical stimulation of the ipsilateral vestibular nerve (61/80 tested). Both non-eye-movement (n = 52) and eye-movement-related (n = 55) units were studied. Unit responses recorded when the head was free to move were compared with responses recorded when the head was restrained from moving. WBR in the absence of a visual target evoked a compensatory vestibulocollic reflex (VCR) that effectively reduced the head velocity in space by an average of 33 +/- 14%. In 73 units, the compensatory head movements were sufficiently large to permit the effect of the VCR on vestibular signal processing to be assessed quantitatively. The VCR affected the rotational responses of different vestibular neurons in different ways. Approximately one-half of the units (34/73, 47%) had responses that decreased as head velocity decreased. However, the responses of many other units (24/73) showed little change. These cells had signals that were better correlated with trunk velocity than with head velocity. The remaining units had responses that were significantly larger (15/73, 21%) when the VCR produced a decrease in head velocity. Eye-movement-related units tended to have rotational responses that were correlated with head velocity. On the other hand, non-eye-movement units tended to have rotational responses that were better correlated with trunk velocity. We conclude that sensory vestibular signals are transformed from head-in-space coordinates to trunk-in-space coordinates on many secondary vestibular neurons in the vestibular nuclei by the addition of inputs related to head rotation on the trunk. This coordinate transformation is presumably important for controlling postural reflexes and constructing a central percept of body orientation and movement in space.

Non-NASA Center↗

NASA NTRS2010

Material condition assessment with eddy current sensors

Eddy current sensors and sensor arrays are used for process quality and material condition assessment of conducting materials. In an embodiment, changes in spatially registered high resolution images taken before and after cold work processing reflect the quality of the process, such as intensity and coverage. These images also permit the suppression or removal of local outlier variations. Anisotropy in a material property, such as magnetic permeability or electrical conductivity, can be intentionally introduced and used to assess material condition resulting from an operation, such as a cold work or heat treatment. The anisotropy is determined by sensors that provide directional property measurements. The sensor directionality arises from constructs that use a linear conducting drive segment to impose the magnetic field in a test material. Maintaining the orientation of this drive segment, and associated sense elements, relative to a material edge provides enhanced sensitivity for crack detection at edges.

Goldfine, Neil J.↗

NASA NTRS2010

Lunar Topographic Mapping Using a New High Resolution Mode for the GSSR Radar

Mapping the Moon's topography using Earth based radar interferometric measurements by the Goldstone Solar System Radar (GSSR) has been done several times since the mid 1990s. In 2008 we reported at this conference the generation of lunar topographic maps having approximately 4 m height accuracy at a horizontal posting of 40 m. Since then GSSR radar has been improved to allow 40 MHz bandwidth imaging and consequently obtained images and interferograms with a resolution of about 4 m in range by 5 m in azimuth. The long synthetic aperture times of approximately 90 minutes in duration necessitated a migration from range/Doppler image formation techniques to spotlight mode processing and autofocusing methods. The improved resolution imagery should permit the generation of topographic maps with a factor of two better spatial resolution with about same height accuracy. Coupled the with the recent availability of new lidar topography maps of the lunar surface made by orbiting satellites of Japan and the United States the geodetic control of the radar generated maps products can be improved dramatically. This paper will discuss the hardware and software improvements made to the GSSR and present some of the new high resolution products.

interferometry↗

NASA NTRS2016

Unique Spectroscopy and Imaging of Mars with the James Webb Space Telescope

In this paper, we summarize the main capabilities of the James Webb Space Telescope (JWST) for performing observations of Mars. The distinctive vantage point of JWST at the Sun-Earth Lagrange point (L2) will allow sampling the full observable disk, permitting the study of short-term phenomena, diurnal processes (across the east-west axis), and latitudinal processes between the hemispheres (including seasonal effects) with excellent spatial resolutions (0.''07 at 2 micron). Spectroscopic observations will be achievable in the 0.7-5 micron spectral region with NIRSpec at a maximum resolving power of 2700 and with 8000 in the 1-1.25 micron range. Imaging will be attainable with the Near-Infrared Camera at 4.3 micrometers and with two narrow filters near 2 micron, while the nightside will be accessible with several filters in 0.5 to 2 micron. Such a powerful suite of instruments will be a major asset for the exploration and characterization of Mars. Some science cases include the mapping of the water D/H ratio, investigations of the Martian mesosphere via the characterization of the non-local thermodynamic equilibrium CO2 emission at 4.3 micron, studies of chemical transport via observations of the O2 nightglow at 1.27 micron, high-cadence mapping of the variability dust and water-ice clouds, and sensitive searches for trace species and hydrated features on the Martian surface. In-flight characterization of the instruments may allow for additional science opportunities.

Villanueva, Geronimo L.↗

DOE OSTI2025

Convection-Permitting Ensembles of an Isolated Mountain Thunderstorm during RELAMPAGO/CACTI

Abstract The north–south-oriented Sierras de Córdoba (SDC) ridge in central Argentina is noted for initiating thunderstorms that may grow into intense mesoscale convective systems (MCSs). It also initiates more isolated, shorter-lived cells under weaker synoptic forcing. These cells are less impactful than MCSs but may be difficult to predict in convective-scale numerical weather prediction (NWP) due to their strong sensitivities to subgrid and partially resolved processes. To study the mechanisms and predictability of such cells, convection-permitting ensemble simulations were conducted of an isolated, diurnally forced SDC thunderstorm during Cloud, Aerosol, and Complex Terrain Interactions (CACTI)/Remote Sensing of Electrification, Lightning, and Mesoscale/Microscale Processes with Adaptive Ground Observations (RELAMPAGO). The rich observational data facilitated detailed ensemble verification, where dry biases in the surface energy balance and soil moisture were identified. These biases promoted rapid removal of convective inhibition and an early onset of precipitating cells over the SDC that were shallower and weaker than the observed cell. Correction, and then overcorrection, of the soil moisture bias in two successive ensembles was required to rectify the surface energy balance and improve the representation of the SDC cell. Nevertheless, substantial ensemble variability in convective precipitation was found, with some members producing more widespread convection than observed and others producing no deep convection at all. This variability was largely explained by a combination of thermodynamic and dynamic mechanisms, dominated by a positive sensitivity of convective precipitation to preconvective moist instability over the ridge. Secondary sensitivities were found to low-level upward mass flux and midlevel cross-barrier winds, the latter of which caused gravity waves with elevated downdrafts that tended to suppress incipient clouds.

Lopez, Andres [Department of Atmospheric and Ocean↗

NASA NTRS1988

Infrared monitoring of the Space Station environment

The measurement and monitoring of infrared emission in the environment of the Space Station has a twofold importance - for the study of the phenomena itself and as an aid in planning and interpreting Station based infrared experiments. Spectral measurements of the infrared component of the spacecraft glow will, along with measurements in other spectral regions, provide data necessary to fully understand and model the physical and chemical processes producing these emissions. The monitoring of the intensity of these emissions will provide background limits for Space Station based infrared experiments and permit the determination of optimum instrument placement and pointing direction. Continuous monitoring of temporal changes in the background radiation (glow) will also permit better interpretation of Station-based infrared earth sensing and astronomical observations. The primary processes producing infrared emissions in the Space Station environment are: (1) Gas phase excitations of Station generated molecules ( e.g., CO2, H2O, organics...) by collisions with the ambient flux of mainly O and N2. Molecular excitations and generation of new species by collisions of ambient molecules with Station surfaces. They provide a list of resulting species, transition energies, excitation cross sections and relevant time constants. The modeled spectrum of the excited species occurs primarily at wavelengths shorter than 8 micrometer. Emissions at longer wavelengths may become important during rocket firing or in the presence of dust.

Kostiuk, Theodor↗

NASA NTRS1987

A processing method and results of meteor shower radar observations

Studies of meteor showers permit the solving of some principal problems of meteor astronomy: to obtain the structure of a stream in cross section and along its orbits; to retrace the evolution of particle orbits of the stream taking into account gravitational and nongravitational forces and to discover the orbital elements of its parent body; to find out the total mass of solid particles ejected from the parent body taking into account physical and chemical evolution of meteor bodies; and to use meteor streams as natural probes for investigation of the average characteristics of the meteor complex in the solar system. A simple and effective method of determining the flux density and mass exponent parameter was worked out. This method and its results are discussed.

Belkovich, O. I.↗

NASA NTRS1995

The composite classification problem in optical information processing

Optical pattern recognition allows objects to be recognized from their images and permits their positional parameters to be estimated accurately in real time. The guiding principle behind optical pattern recognition is that a lens focusing a beam of coherent light modulated with an image produces the two-dimensinal Fourier transform of that image. When the resulting output is further transformed by the matched filter corresponding to the original image, one obtains the autocorrelation function of the original image, which has a peak at the origin. Such a device is called an optical correlator and may be used to recognize the locate the image for which it is designed. (From a practical perspective, an approximation to the matched filter must be used since the spatial light modulator (SLM) on which the filter is implemented usually does not allow one to independently control both the magnitude and phase of the filter.) Generally, one is not just concerned with recognizing a single image but is interested in recognizing a variety of rotated and scaled views of a particular image. In order to recognize these different views using an optical correlator, one may select a subset of these views (whose elements are called training images) and then use a composite filter that is designed to produce a correlation peak for each training image. Presumably, these peaks should be sharp and easily distinguishable from the surrounding correlation plane values. In this report we consider two areas of research regarding composite optical correlators. First, we consider the question of how best to choose the training images that are used to design the composite filter. With regard to quantity, the number of training images should be large enough to adequately represent all possible views of the targeted object yet small enough to ensure that the resolution of the filter is not exhausted. As for the images themselves, they should be distinct enough to avoid numerical difficulties yet similar enough to avoid gaps in which certain views of the target will be unrecognized. One method that we introduce to study this problem is called probing and involves the creation of the artificial imagery. The second problem we consider involves the clasification of the composite filter's correlation plane data. In particular, we would like to determine not only whether or not we are viewing a training image, but, in the former case, we would like to determine which training image is being viewed. This second problem is investigated using traditional M-ary hypothesis testing techniques.

Hall, Eric B.↗

NASA NTRS1993

Containerless processing of undercooled melts

The investigation focused on the control of microstructural evolution in Mn-Al, Fe-Ni, Ni-V, and Au-Pb-Sb alloys through the high undercooling levels provided by containerless processing, and provided fundamental new information on the control of nucleation. Solidification analysis was conducted by means of thermal analysis, x-ray diffraction, and metallographic characterization on samples processed in a laboratory scale drop tube system. The Mn-Al alloy system offers a useful model system with the capability of phase separation on an individual particle basis, thus permitting a more complete understanding of the operative kinetics and the key containerless processing variables. This system provided the opportunity of analyzing the nucleation rate as a function of processing conditions and allowed for the quantitative assessment of the relevant processing parameters. These factors are essential in the development of a containerless processing model which has a predictive capability. Similarly, Ni-V is a model system that was used to study duplex partitionless solidification, which is a structure possible only in high under cooling solidification processes. Nucleation kinetics for the competing bcc and fcc phases were studied to determine how this structure can develop and the conditions under which it may occur. The Fe-Ni alloy system was studied to identify microstructural transitions with controlled variations in sample size and composition during containerless solidification. This work was forwarded to develop a microstructure map which delineates regimes of structural evolution and provides a unified analysis of experimental observations. The Au-Pb-Sb system was investigated to characterize the thermodynamic properties of the undercooled liquid phase and to characterize the glass transition under a variety of processing conditions. By analyzing key containerless processing parameters in a ground based drop tube study, a carefully designed flight experiment may be planned to utilize the extended duration microgravity conditions of orbiting spacecraft.

Perepezko, J. H.↗