SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This data set consists of the data used to generate the figures in the paper titled "Wall conditioning effects of boron powder injection in KSTAR with a tungsten divertor" in the journal Nuclear Fusion, 2025.
The operational environment for plasma heating systems presents unprecedented challenges for the success of magnetic fusion. This chapter discusses the current state of ion cyclotron and electron cyclotron heating systems and the research and development priorities needed to establish working solutions for these systems. While much progress has been made, there is much more work to be done to make fusion energy commercially viable. Research and development priorities include radiation-resistant structural and plasma facing materials, advanced manufacturing methods, new cooling methods, first-wall integrated actuators, improvements in power source efficiency, higher frequency gyrotrons, and improved overall system reliability.
This work proposes an approach to minimize surface energy deactivation of plasma-treated metal and carbon fiber-reinforced polymer (CFRP) surfaces by vacuum sealing. Plasma treatments enhance adhesive wettability on post-treated surfaces for adhesive joints, but the treated surfaces deactivate quickly in air. The surface energy of aluminum alloy AA6061 and carbon fiber-reinforced polymer-polyamide (CFRP-PA66) optimally treated by a blown air plasma instrument returns to the original surface energy within one hour. Vacuum sealing of AA6061 and CFRP-PA66 reduced the surface energy deactivation over 7 days by at least 230 times and 970 times compared to in air. Double Cantilever Beam (DCB) tests performed on adhesively-bonded AA6061/CFRP-PA66 joints showed that the total energy release and energy dissipation before failure of plasma-treated and vacuum-sealed materials was up to 60% more than plasma-treated materials without vacuum sealing and up to 125% more than non-plasma-treated materials.
A novel surface restoration approach combining plasma gouging with subsequent cold spray deposition is demonstrated in this study. Plasma gouging effectively removes the damaged steel surface, leaving grooves and forming a plasma gouging affected zone up to ~300?µm thick. Within this zone, a hardened martensitic layer with a peak hardness of ~370?HV—almost twice that of the base substrate (~200?HV)—is produced. Following plasma gouging, cold spray deposition is applied to rebuild the surface. Experimental results reveal that cold spray coatings deposited at low energy suffer from delamination, whereas high energy cold spray deposits yield a well-bonded coating. Microstructural analysis further shows that the martensitic layer formed by plasma gouging undergoes dynamic recrystallization during cold spray, reducing the hardness to 317?HV. These findings demonstrate the feasibility of this hybrid method for effective surface restoration of damaged steel components.
Developing advanced materials for plasma-facing components (PFCs) in fusion reactors is a crucial aspect for achieving sustained energy production. Tungsten (W) - based refractory high-entropy alloys (RHEAs) have emerged as promising candidates due to their superior radiation tolerance and high-temperature strength. This review paper will focus on recent advancements in W-based RHEA research, particularly emphasizing the key role of modelling using machine learning (ML) in the stage of discovery by predicting properties for each composition and expediting the identification of optimal RHEA compositions with desired properties. Additionally, the application of additive manufacturing (AM) techniques for fabricating W-based RHEAs is explored, highlighting their advantages for rapid prototyping and multi-compositional sample production in a high throughput manner. The review critically evaluates the current understanding of mechanical properties relevant to PFC applications, including high-temperature strength and ductility. Furthermore, the radiation tolerance of W-based RHEAs under irradiated conditions is discussed. Finally, the validity of current AM-manufactured W-based RHEAs as PFC materials is assessed, and key challenges and opportunities for future research are identified. This review aims to provide a comprehensive overview of W-based RHEAs for fusion applications and their potential to guide the development and validation of advanced refractory high entropy alloys.
The principal goals of this project were to develop key physics understandings and control solutions necessary for the realization of a steady-state fusion reactor by adapting high performance plasma scenarios from DIII-D to long pulse operation on the Experimental Advanced Superconducting Tokamak (EAST) in Hefei, China. Specific research objectives include the development of physics and control solutions necessary for demonstrating disruption-free long-pulse plasmas at high physics performance sustained simultaneously with the capability of handling the plasma exhaust and plasma-wall interactions using reactor-relevant materials surrounding the plasma.
We use x-ray pulses from dense argon plasmas at the Z Machine (Sandia National Laboratories) to generate hypersonic aluminum plasmas akin to material ejecta during proposed planetary defense missions, fusion reactor wall excursions, and other high-energy density processes. Near-infrared absorption is used to diagnose the controlled expansion of the plasmas through cylindrical cavities following their generation from x-ray heating of solid aluminum 7075 alloy. The data are compared to multidimensional radiation hydrodynamics simulations utilizing the ALEGRA multiphysics code, accounting for the dynamics of radiation scattering, material phase change, plasma expansion, thermal re-irradiation, and interactions with the cavity and with the infrared beams. To allow for accurate simulation, density functional theory is used to apply the Hagen–Rubens relation for the far-infrared and is adjoined with a detailed configuration accounting model using the Propaceos code, producing opacities spanning 10 −1 –10 4 eV photon energy for aluminum 7075 alloy, and in comparison with pure aluminum. The model is found to agree with experimental data in the higher-fluence regime when the Hagen–Rubens relation is applied. The ejected material, which is observed to travel up to 55 km/s, is comprised of a strongly ionized, non-LTE plasma front at ∼10 eV temperature followed by a weakly ionized LTE gas at higher density. The present findings lend some confidence to the broad-range equation of state and infrared opacity models for weakly ionized aluminum plasmas while demonstrating an approach to their future refinement, with potential application to astrophysical plasmas and other extreme processes.
Electron beams with an applied magnetic field generate a secondary cold plasma with a selective chemical composition, featuring low-energy ions and metastable species in the discharge periphery, ideal for low-damage plasma treatment of material substrates. In this work, we studied the plasma generated by an e-beam using a 4 kV voltage in a pure argon gas environment under a magnetic field of 150 G and in the pressure range of 25–90 mTorr. We measured the absolute spatial density profile of argon (1 s 5 ) metastables in an electron beam generated plasma by laser-induced fluorescence and found it to be of the order of 10 16 m −3 . The electron temperature and the electron density measured by a Langmuir probe were of the order of 10 16 m −3 and less than an eV respectively. Electron-impact quenching was identified as a significant loss mechanism for the Ar(1s 5 ) state, leading to the saturation of the metastable density at higher pressures. Outside the primary ionization region, the spatial distribution of argon metastables followed a linear diffusion profile, indicating negligible additional production in those regions.
This work investigated air plasma effect on the Mode I crack growth resistance of adhesively-bonded metal-CFRTP dissimilar joints by using aluminum alloy (AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) as an example, and the Double Cantilever Beam (DCB) fracture testing as an evaluation method. The results show that air plasma treatment can significantly improve the fracture resistance of adhesively-bonded AA6061-CFRPA66 dissimilar joints with about 140% enhanced Mode I fracture energy in maximum compared to non-treated ones. The quantified fracture energies from size effect method for both non-treated and plasma-treated cases are geometry-independent, whereas this is not true for modified beam theory causing geometry-dependent results. The foregoing improvement was confirmed from the failure surface morphology of plasma-treated specimens, showing fibers peeling off from CFRPA66 surface due to plasma-enhanced bonding between CFRPA66 and adhesive by the formation of covalent bonds at their interface. This study demonstrated air plasma as an efficient surface modification method to enhance the fracture resistance of adhesively-bonded metal-CFRTP dissimilar joints, and size effect method as a characterization method to properly quantify their fracture properties. These aspects are valuable in the area of multi-materials joining.
Inspired by the ideas of many authors, we provide insight on state-of-the-art potential technologies for the prevention and prediction of infectious diseases before they spread. This review also surveys virus sterilization with ultraviolet light and low temperature plasma technologies. Researchers in the various fields of medicine, materials, electronics, and plasma sciences have addressed increasingly challenging demands and the discussion encompasses the major challenges in societies that are faced with the threat of infectious diseases. In addition, technologies that use nanomaterials are evaluated for infection prevention and hygiene purposes. Advances in biomedical diagnostics for health care in terms of complementary metal-oxide-semiconductor transistors-based devices and telemetry for health monitoring are also reviewed.
Abstract Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m −3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s −1 (1– 4.2 × 10 20 Si s −1 ) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO 2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s −1 . The technique is estimated to coat a surface area of at least 0.94 m 2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.
The magnetic pre-sheath (MPS) width, L MPS , is a critical parameter to define the sheath potential, which controls the ion trajectory of low-Z species (D, T, He, and C), as well as the prompt re-deposition of high-Z species. In this work, to determine L MPS , we fabricated micro-trenches (30×30×4 µm) via focused ion beam (FIB) milling on a silicon surface and exposed them to L-mode deuterium plasmas in DIII-D via the Divertor Material Evaluation System (DiMES) removable sample exposure probe. The areal distribution of impurity depositions, mainly consisting of carbon, was measured by energy-dispersive X-ray spectroscopy (EDS) to reveal the deuterium ion shadowing effect on the trench floors. The carbon deposition profiles showed that the erosion was maximized for the azimuthal direction of φ = -40° (referenced to the toroidal magnetic field direction) as well as the polar angle of θ = 80°. A Monte Carlo equation-of-motion model, based on a collisionless MPS, was used to calculate the azimuthal and polar deuterium ion angle distributions (IADs) for a range of L MPS = k × ρ i , where ρ i is the ion gyro radius and k = 0.5-4. Then, gross erosion profiles were calculated by a Monte Carlo micro-patterning and roughness (MPR) code for ion sputtering using as input the calculated azimuthal and polar IADs for each value of k . Good agreement with the experimental C deposition profiles was obtained for the case k = 2.5-3.5. This result is consistent with a previous kinetic modeling prediction of k ~ 3, as well as previous analytical investigations that predicted the L MPS to be several ion gyro radii. A validation of theoretical sheath models supports its applicability to ITER and pilot plant divertors to successfully predict plasma-materials interactions.
In this work, we present numerical simulation results of powder injection in W7-X using the EMC3-EIRENE and DIS codes. First, we model powder injection experiments performed in W7-X with the Probe Mounted Powder Injector. The simulation results qualitatively agree with visible imaging measurements. Secondly, we perform predictive simulations to guide the installation of an Impurity Powder Dropper in W7-X, allowing to choose in between several available non-vertical ports to maximize the amount of powder penetrating into the plasma, as well as the verticality of the port, to minimize sticking of the powders in the in-vessel stainless steel guiding tube. Port AEM41 is selected as the best candidate for IPD installation. The robustness of the simulation results has been verified for different plasma densities, powder materials and sizes, powder friction coefficient and changes in the plasma flow.
In this study, a new simulation model for tokamak boundary plasma, SOLT3D, is implemented in the BOUT++ framework. The simulation model includes a set of dynamic equations describing collisional boundary plasma and neutral gas in the tokamak scrape-off layer and divertor region. The model is verified against standard linear plasma instabilities and available nonlinear results. For L-mode like conditions, SOLT3D reproduces characteristics of boundary plasma turbulent fluctuations that are similar to published experimental data, in terms of the amplitude and spatial dependence of the fluctuations. It also reproduces realistic plasma fluxes on material surfaces and expected Bohm-like effective radial transport. Plasma fluctuations inferred from the simulations imply inevitably a significant level of intrinsic 'noise' for axisymmetric tokamak plasma transport modeling, introducing errors on the order of unity. In particular, the toroidally averaged atomic rates below 5–10 eV are strongly modified by turbulent plasma fluctuations, which should significantly affect the standard axisymmetric modeling of the tokamak edge plasma and divertor.
This project focused on the development and integration of high-performance simulation tools to predict the operating behavior of Plasma-Facing Components in magnetic confinement fusion systems. A key objective at Illinois was to assess the impact of the dynamic interplay between the evolving material surface and the magnetized plasma sheath, and characterize the impact of tungsten-based PFCs on plasma contamination, including phenomena such as surface erosion, dynamic recycling of fuel species, and tritium retention, which are critical for the success of future magnetic fusion devices.
The successful operation of thermonuclear fusion reactors such as ITER, DEMO, and future commercial plants is mainly determined by the optimum choice of materials for various components. The objective of this work is to accurately and comprehensively simulate the entire device in 3D to predict pros and cons of various materials, e.g., liquid lithium in comparison to tungsten and carbon to predict future ITER-like and DEMO divertor performances. We used our comprehensive HEIGHTS simulation package to investigate ITER-like components response during transient events in exact 3D geometry. Starting from the lost hot core plasma particles through SOL, deposition on the divertor surface, and the generation of secondary plasma of divertor materials. Our simulations predicted significant reduction in the heat loading and damage to the divertor nearby and internal components in the case when lithium is used on the divertor plates. While if tungsten or carbon are used on the divertor plate, significant melting areas and vaporization spots can occur (less for carbon) on the reflector, dome, and stainless steel tubes, and even parts of the first walls can melt due to the high radiation power of the secondary divertor plasma. Lithium photon radiation deposition into the divertor and nearby surfaces was decreased by two orders of magnitude compared to tungsten and by one order of magnitude compared to carbon. This analysis showed that using liquid lithium for ITER-like surfaces and future DEMO can lead to significant enhancement in components lifetime.
One technique for mitigating disruptions in a tokamak is shattered pellet injection (SPI). SPI is a process in which a large solid pellet consisting of deuterium, neon, or argon is desublimated in a pipe gun barsrel and launched downstream. Pellets are shattered just before entering the plasma by an impact with an angled tube. Injection of these materials into the plasma radiates stored thermal energy, limits current decay rates, suppresses the generation of runaway electrons, and dissipates runaway electrons if necessary. A critical element of the SPI system is a fast-acting valve that releases high-pressure gas to dislodge and accelerate pellets directly, or indirectly via a mechanical punch. A prototype valve sized for the ITER SPI system has been designed and fabricated. A pulsed high-voltage power supply energizes the valve’s internal magnetic coil, which induces eddy currents in the adjacent flyer plate resulting in a repulsive force between the flyer plate and the coil. The flyer plate action lifts a valve seat, allowing high-pressure gas to flow from the valve plenum to the downstream (breech) location of the pellet or mechanical punch. All of the valve’s internal components are designed to operate in ITER-level static background magnetic fields. Here, a study was conducted to optimize the downstream pressure response for a range of valve sizes and operating pressures. In particular, the study analyzes the breech pressure response associated with varying plenum pressures as well as varying breech volumes. A computational fluid dynamics simulation was built in STAR-CCM+ and validated against data from laboratory experiments. The resulting simulation outputs, in the form of downstream responses for a variety of initial plenum pressures and breech volumes, will be used as a complement to experimental data to ensure the pressure pulse is suitable for pellet survivability. These data, combined with studies on pellet shear strength and shock response, will be applied to optimization of overall operating parameters of the ITER SPI system.
Recently, it was shown that strong electron thermionic emission from material walls could result in the formation of an “inverse sheath”, which prevents the flow of cold ions to the wall. Such regimes look very favorably from the point of view of plasma-material interactions at the edge of magnetic fusion devices, where the problem of the erosion of plasma facing components under ion irradiation is one of the key issues for developing of future magnetic fusion reactors. However, it is not clear whether such regimes are compatible with edge plasma parameters and heat removal requirements in fusion reactors.To address the issue of practicality of the “inverse sheath” regime for edge tokamak plasma conditions, we perform a set of numerical simulations with 2D edge plasma transport code UEDGE for a DIII-D-like geometry and magnetic configuration.To describe both “standard” and “inverse sheath” conditions within the framework of the UEDGE code (which does not consider the sheath region per se), at the material surfaces, we apply effective boundary conditions which emulate both “standard” and“inverse sheath” regimes. We demonstrate that for the same input parameters, spatial distributions of edge plasma parameters corresponding to detached divertor and“inverse sheath” regimes are similar, with only a few minor differences. We discuss the compatibility of “inverse sheath” regimes with core plasma parameters.