Search NASA⌕ Search

SEARCH · Search NASA

Results for “Plenum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Turbulent Flow of Coolant in an Advanced Nuclear Reactor

Award-winning visualization from Argonne National Laboratory! The video represents the turbulent flow of coolant into a mock-up of the upper plenum of an advanced recycling nuclear reactor. The colors indicate the speed of the fluid, with red representing regions of high velocity and blue representing regions of low velocity. Performed at the Argonne Leadership Computing Facility at Argonne National Laboratory. The computations were carried out on one of the world's fastest and most energy-efficient supercomputers: Intrepid, Argonne's IBM Blue Gene/P. The visualizations were performed on Eureka with software developed at Argonne. Eureka is also located at the ALCF and is one of the world's largest graphics processing units, providing more than 111 teraflops and over 3.2 terabytes of RAM. Read more at http://www.anl.gov/Media_Center/News/2009/news090624.html.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Full-length U-xPu-10Zr (x=0, 8, 19 wt%) Fast Reactor Fuel Test in FFTF

The Integral Fast Reactor-1 (IFR-1) experiment performed in the Fast Flux Test Facility (FFTF) was the only U-Pu-10Zr (Pu-0, 8 and 19 wt%) metallic fast reactor test with commercial-length (91.4 cm active fuel column length) conducted to date. With few remaining test reactors there is little opportunity for performing another test with a long active fuel column. The assembly was irradiated to the goal burnup of 10 at.%. The beginning of life (BOL) peak cladding temperature of the hottest pin was 608?C, cooling to 522?C at end of life (EOL). Selected fuel pins were examined non destructively using neutron radiography, precision axial gamma scanning, and both laser and spiral contact cladding profilometry. Destructive exams included plenum gas pressure, volume, and gas composition determinations on a number of pins followed by optical metallography, electron probe microanalysis (EPMA), and alpha and beta gamma autoradiography on a single U-19Pu-10Zr pin. The post-irradiation examinations (PIEs) showed very few differences compared to the short-pin (34.3 cm fuel column) testing performed on fuels of similar composition in Experimental Breeder Reactor-II (EBR-II). The fuel column grew axially slightly less than observed in the short pins, but with the same pattern of decreasing growth with increasing Pu content. There was a difference in the fuel-cladding chemical interaction (FCCI) in that the maximum cladding penetration by interdiffusion with fuel/fission products did not occur at the top of the fuel column where the cladding temperature is highest, as observed in EBR-II tests. Instead, the more exaggerated fission-rate profile of the FFTF pins resulted in a peak FCCI at ~0.7 X/L axial location along the fuel column. This resulted from a lower production of rare earth fission products higher in the fuel column as well as a much smaller delta-T between fuel center and cladding, and therefore less FCCI, despite the higher cladding temperature. This behavior could actually help extend the life of a fuel pin in a “long pin” reactor design to a higher peak fuel burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Natural Circulation Patterns in the VHTR Air-Ingress Accident and Related Issues

A natural circulation pattern in a Very High Gas-Cooled Reactor during a hypothetical air-ingress accident has been investigated using computational fluid dynamic (CFD) methods in order to compare with the previous 1-D flow path model for the air-ingress analyses. The GT-MHR 600 MWt reactor was selected to be the reference design and modeled by a half symmetric 3-D geometry using FLUENT 6.3, a commercial CFD code. The simulation was carried out as steady-state calculations, and the boundary conditions were either assumed or provided from the 1-D GAMMA code results. Totally, 12 different cases have been estimated, and many notable findings and results have been obtained in this study. According to the simulations, the natural circulation pattern in the reactor was quite different from the previous 1-D assumptions. A large re-circulation flow with thermal stratification phenomena was clearly observed in the hot-leg and the lower plenum in the 3-D model. This re-circulation flow provided approximately an order faster air-ingress speed (0.46 m/s in superficial velocity) than previously predicted values by 1-D modeling (0.02~0.03 m/s). It indicates that the 1-D air-ingress modeling may significantly distort the air-ingress scenario and consequences. In addition, the complicated natural circulation pattern is eventually expected to lead to very complex graphite oxidations and corrosion patterns.

99 GENERAL AND MISCELLANEOUS↗

Multiple tube premixing device

The present application provides a premixer for a combustor. The premixer may include a fuel plenum with a number of fuel tubes and a burner tube with a number of air tubes. The fuel tubes extend about the air tubes.

42 ENGINEERING↗

Choked-Flow Inlet Orifice Bubbler for Creating Small Bubbles in Mercury

Pressure waves created in liquid mercury pulsed spallation targets like the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, induce cavitation damage on the target container. The cavitation damage is thought to limit the lifetime of the target for power levels at and above 1 MW. One way to mitigate the damage would be to absorb the pressure pulse energy into a dispersed population of small bubbles, however, creating a bubble size distribution that is sufficiently large and disperse in mercury is challenging due to the high surface tension. Also, measuring the population is complicated by the opacity and the high level of turbulent mixing. Recent advances in bubble diagnostics by batch sampling the mercury made it possible to compare bubble populations for different techniques in a SNS-1/20th scale test loop. More than 10 bubblers were tested and the most productive bubblers were taken for in-beam testing at the Los Alamos Neutron Science Center (LANSCE) WNR user facility. One bubbler design, referred to as the inlet-orifice bubbler, that showed moderate success in creating populations also has an added advantage that it could easily be included in the existing SNS full-scale mercury target configuration. Improvements to the bubbler were planned including a reduction of the nozzle size to choke the gas injection, thus steadying the injected mass flow and allowing multiple nozzles to work off of a common plenum. For the first time, reliable bubble population data are available in the prototypical target geometry and can be compared with populations that mitigated cavitation damage. This paper presents those experimental results.

mercury bubbles SNS cavitation damage mitigation e↗

Multiple tube premixing device

The present application provides a premixer for a combustor. The premixer may include a fuel plenum with a number of fuel tubes and a burner tube with a number of air tubes. The fuel tubes extend about the air tubes.

42 ENGINEERING↗

Apparatus and method for cooling a combustor cap

A combustor includes an end cap having a perforated downstream plate and a combustion chamber downstream of the downstream plate. A plenum is in fluid communication with the downstream plate and supplies a cooling medium to the combustion chamber through the perforations in the downstream plate. A method for cooling a combustor includes flowing a cooling medium into a combustor end cap and impinging the cooling medium on a downstream plate in the combustor end cap. The method further includes flowing the cooling medium into a combustion chamber through perforations in the downstream plate.

42 ENGINEERING↗

Regeneratively cooled transition duct with transversely buffered impingement nozzles

A cooling arrangement (56) having: a duct (30) configured to receive hot gases (16) from a combustor; and a flow sleeve (50) surrounding the duct and defining a cooling plenum (52) there between, wherein the flow sleeve is configured to form impingement cooling jets (70) emanating from dimples (82) in the flow sleeve effective to predominately cool the duct in an impingement cooling zone (60), and wherein the flow sleeve defines a convection cooling zone (64) effective to cool the duct solely via a cross-flow (76), the cross-flow comprising cooling fluid (72) exhausting from the impingement cooling zone. In the impingement cooling zone an undimpled portion (84) of the flow sleeve tapers away from the duct as the undimpled portion nears the convection cooling zone. The flow sleeve is configured to effect a greater velocity of the cross-flow in the convection cooling zone than in the impingement cooling zone.

42 ENGINEERING↗

Effect of Feeding Rate on the Cold Cap Configuration in a Laboratory-Scale Melter

High level waste melter feed is converted into glass in a joule heated melter, where it forms a floating layer of reacting feed, called the cold cap. After the glass-forming phase becomes connected, evolving gases produce bubbles that form a foam layer under the cold cap. The bubbles coalesce into cavities that escape around the edges of the cold cap. The foam layer insulates the cold cap from the heat transferred from the molten glass below. More information is needed about the formation and behavior of the foam layer to control, limit and possibly avoid foaming, thus allowing for a higher rate of melting. The cold cap behavior was investigated in a laboratory scale assembly with a sealed silica-glass crucible. A high alumina waste simulant was fed into the crucible and the feed charging rate was varied from 3 to 7 mL min-1. After a fixed amount of time (35 min), feed charging was stopped and the crucible was removed from the furnace and quenched on a copper block to preserve the structure of the cold cap and foam during cooling. During the rapid quenching, thermal cracking of the glass and cold cap allowed it to be broken up into sections for analysis. The effect of the charging rate on the height, area and volume of the cold cap was determined. The size of the bubbles collected in the foam layer under the cold cap increased as the cold cap expanded. Under the cold cap, the bubbles coalesced into oblong cavities. These cavities allowed the evolved gases to escape around the edges of the cold cap through the molten glass into the melter plenum.

Dixon, Derek R.↗

Multi-scale evaporator architectures for geothermal binary power plants

In this paper, novel geometries of heat exchanger architectures are proposed for evaporators that are used in Organic Rankine Cycles. A multi-scale heat exchanger concept was developed by employing successive plenums at several length-scale levels. Flow passages contain features at both macro-scale and micro-scale, which are designed from Constructal Theory principles. Aside from pumping power and overall thermal resistance, several factors were considered in order to fully assess the performance of the new heat exchangers, such as weight of metal structures, surface area per unit volume, and total footprint. Component simulations based on laminar flow correlations for supercritical R134a were used to obtain performance indicators.

Sabau, Adrian S↗

A Web-Based Simulation Tool on The Performance of Different Roofing Systems

The Roof Savings Calculator (www.roofcalc.com) provides the general public with a web-based program for calculating the energy savings of different roofing and attic systems on four different building types (residential, office, retail, and warehouse) in 239 US TMY2 locations. The core simulation engine of the RSC is doe2attic, which couples the AtticSim program developed by Oak Ridge National Laboratory with the DOE-2.1E program originally developed by Lawrence Berkeley National Laboratory a widely used whole-building simulation program since the 1980 s. Although simulating heat flows through the roof may seem to be an easy task, simulating the net effect of roofing strategies on building heating and cooling energy use can be quite challenging. Few simulation programs can reliably capture dynamics including an attic or plenum with large day-night temperature swings, high ventilation rates, significant radiant exchange between the roof and the attic floor and thermal interactions when there are ducts in the attic, as is typical in North American buildings. The doe2attic program has been tested against detailed measurements gathered in two residential buildings in Fresno, California from cooling energy use to air and surface temperatures, and heat fluxes of the roof and attic floor. The focus of this paper is on the doe2attic simulation tool, but the user interface of the RSC will also be briefly described.

Huang, Joe↗

Heat Transfer Model of a Small-Scale Waste Glass Melter with Cold Cap Layer

At the Hanford site in the state of Washington, more than 56 million gallons of radioactive waste is stored in underground tanks. The cleanup plan for this waste is vitrification at the Waste Treatment Plant (WTP), currently under construction. At the WTP, the waste will be blended with glass-forming materials and heated to 1423K, then poured into stainless steel canisters to cool and solidify. A fundamental understanding of the glass batch melting process is needed to optimize the process to reduce cost and decrease the life cycle of the cleanup effort. The cold cap layer that floats on the surface of the glass melt is the primary reaction zone for the feed-to-glass conversion. The conversion reactions include water release, melting of salts, evolution of batch gases, dissolution of quartz and the formation of molten glass. Obtaining efficient heat transfer to this region is crucial to achieving high rates of glass conversion. Computational fluid dynamics (CFD) modeling is being used to understand the heat transfer dynamics of the system and provide insight to optimize the process. A CFD model was developed to simulate the DM1200, a pilot-scale melter that has been extensively tested by the Vitreous State Laboratory (VSL). Electrodes are built into the melter to provide Joule heating to the molten glass. To promote heat transfer from the molten glass into the reactive cold cap layer, bubbling of the molten glass is used to stimulate forced convection within the melt pool. A three-phase volume of fluid approach is utilized to model the system, wherein the molten glass and cold cap regions are modeled as separate liquid phases, and the bubbling gas and plenum regions are modeled as one lumped gas phase. The modeling of the entire system with a volume of fluid model allows for the prescription of physical properties on a per-phase basis. The molten glass phase and the gas phase physical properties are obtained from previous experimental work. Finding representative properties for the cold cap region is more difficult, as this region is not a true liquid, but rather a multilayer region consisting of a porous and a foamy layer. Physical properties affecting heat transfer, namely the thermal conductivity and heat capacity, have been fit to closely match data and observations from laboratory experiments. Data from xray tomography and quenching of laboratory-scale cold caps provide insight into the topology of bubble distribution within the cold cap at various temperatures. Heat transfer within the melter was validated by comparison with VSL data for the pilot-scale melter.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal Stratification Modeling for Sodium-Cooled Fast Reactors: A Status Update

Thermal hydraulic behavior in the upper plenum of pool- type sodium-cooled fast reactors (SFRs) is a major concern, as many design challenges are concentrated in this region. As SFR designs aim for licensing and commercialization, it is important to accurately analyze and predict the thermal-hydraulic behavior in this region during accident scenarios, specifically thermal stratification. Thermal stratification models are currently a major source of uncertainty in most system codes for all types of power plants. Most system codes, including SAS4A/SASSYS-1, a system level code developed by Argonne National Laboratory (Argonne), use very coarse meshes that cannot capture the complexities of the stratification phenomena. While the commonly employed lumped-volume based models for thermal stratification are able to run in a matter of seconds, they result in approximate results and can only handle simple cases. Other 2-D and 3-D methods, such as computational fluid dynamics (CFD) models, can analyze simple configurations with higher fidelity, but come with a relatively large computational expense. Finding a modeling solution that is both accurate and computationally efficient has proven difficult. This paper provides details of a review and gap analysis of the various modeling approaches proposed to date and explores a path forward for future thermal stratification modeling efforts, with a focus on developing new models for the SAS4A/SASSYS-1 system code.

Morgan, Sarah↗

Modeling Fission Gas Behaviour with the BISON Fuel Performance Code

The behavior of fission gases (Xe, Kr) is of critical importance to nuclear fuel performance, because it determines both the amount of fuel swelling and the quantity of fission gas released to the fuel rod plenum. It follows that accurate models of fission gas behavior need to be developed for the calculation of fission gas swelling and release in fuel performance codes, such as the BISON code developed at Idaho National Laboratory (INL). To this end, the fission gas behavior model included in BISON is being continually extended and improved. In the present contribution, we give an account of the most recent developments and results on modeling fission gas behavior in uranium dioxide fuel with BISON.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Bundled tube fuel nozzle assembly with liquid fuel capability

A bundled tube fuel nozzle assembly includes a fuel injector and a tube bundle comprising a plurality of tubes that provide for fluid communication through a forward plate, a fuel plenum and an aft plate of the bundled tube fuel nozzle assembly. Each tube includes an inlet defined at an upstream end of the tube and an outlet defined at a downstream end of the tube. The fuel injector is disposed upstream from the inlets of each of the tubes. The upstream end of each tube is noncircular and includes at least one side portion that abuts a complementary upstream end side portion of an immediately adjacent tube of the plurality of tubes. The downstream end of each tube may be circular and is spaced apart from the downstream ends of immediately adjacent tubes of the plurality of tubes.

42 ENGINEERING↗

Method for using an air-sparged hydrocyclone for cryogenic gas vapor separation

A method for separating a vapor from a carrier gas is disclosed. An air-sparged hydrocyclone is provided with a porous sparger covered by an outer gas plenum. A cryogenic liquid is provided to the tangential feed inlet at a velocity that induces a tangential flow and a cyclone vortex in the cyclone. The carrier gas is injected into the air-sparged hydrocyclone through the porous sparger. The vapor dissolves, condenses, desublimates, or a combination thereof, forming a vapor-depleted carrier gas and a vapor-enriched cryogenic liquid. The vapor-depleted gas is drawn through a vortex finder while the vapor-enriched cryogenic liquid is drawn through an apex nozzle outlet. In this manner, the vapor is removed from the carrier gas.

Baxter, Larry↗

MULTIDIMENSIONAL NUMERICAL SIMULATIONS OF REACTING FLOW IN A NON-PREMIXED ROTATING DETONATION ENGINE

Over the last two decades, detonation based propulsion has received a great deal of attention as a potential means to achieve significant improvement in the performance of air-breathing and rocket engines. Detonative combustion mode is particularly interesting due to the resulting pressure gain from reactants to products, faster heat release, decreased entropy generation, more available work and higher thrust compared to conventional deflagrative combustion. Rotating detonation engine (RDE) is one such novel combustor concept. Realistic RDE configurations utilize separate fuel and air injection schemes, hence are not perfectly premixed. Moreover, RDE performance is governed by a large number of design parameters and operating conditions. In this context, computational fluid dynamics (CFD) has the potential to enhance the understanding of RDE combustion and aid future development/optimization of this technology. In the present work, a CFD model was developed to simulate a representative non-premixed RDE combustor. Unsteady Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for the full combustor geometry (including the separate fuel and air injection ports), with hydrogen as fuel and air as the oxidizer. Adaptive mesh refinement (AMR) was incorporated to achieve a trade-off between model accuracy and computational expense. A finite-rate chemistry model along with a 10-species detailed kinetic mechanism was employed to describe the H2-Air combustion chemistry. Two operating conditions were simulated, corresponding to the same global equivalence ratio of unity but different fuel and air mass flow rates. For both conditions, the capability of the model to capture the essential detonation wave dynamics was assessed. A validation study was performed against experimental data available on detonation wave frequency/height, reactant fill height, oblique shock angle, axial pressure distribution in the channel, and fuel/air plenum pressure. The CFD model predicted the sensitivity of these wave characteristics to the operating conditions with good accuracy, both qualitatively and quantitatively. The present CFD model offers a potential capability to perform rapid design space exploration and/or performance optimization studies for realistic full-scale RDE configurations.

Pal, Pinaki↗

Computational experiments to characterize bubble formation and movement in waste glass foam layer

Computer simulation experiments are a valuable complement to physical experimentation for systems where there is limited access to quantities of interest. The motivation for this work is to characterize the fluid dynamic and heat transfer processes that affect melt rate of waste slurry during vitrification, which can limit the throughput rate of the melter. Heat transfer to the cold cap from the molten glass below this layer is an important factor determining melt rate. In this study, computational fluid dynamics is used to elucidate the behavior of gas-filled cavities that form underneath the cold cap in a laboratory-scale waste glass melter. The cold cap consists of a reacting feed layer above a foam layer. The cavities are a result of coalesced gases from collapsing primary foam and air from forced convection bubblers. Bubbles in the foam layer move horizontally with the circulation pattern of the melt and escape around the edges of the cold cap to the plenum above. The effects of varying thermophysical properties and foam parameters based on the bounds of high-level waste glass formulations were explored. Using the DAKOTA toolkit, a Latin hypercube space-filling design was used to randomly distribute samples in bins to achieve good coverage over the parameter space with minimal points. Using the results from the set of simulations, a Gaussian process model with a linear trend was used to create response surfaces for several key quantities of interest, including temperatures, temperature gradients, velocities, and foam extent beneath the cold cap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗