Search NASA⌕ Search

SEARCH · Search NASA

Results for “Post Irradiation Examination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Microstructural characterization of cold-worked 316 stainless steel flux thimble tubes irradiated up to 100 dpa in a commercial Pressurized Water Reactor

Two flux thimble tubes (FTT) made of 15% cold-worked 316 stainless steel (SS) were harvested from Ringhals Pressurized Water Reactor (PWR) Unit 2, with peak damages of 76 and 100 displacements per atom (dpa) after 29 and 34 years’ service, respectively. Specimens sectioned from parent tubes were comprehensively characterized with nominal damage levels of ~0, ~41, ~74, 76, and 100 dpa at a nominal temperature range of 285-323 °C. Both FTTs contained helium and hydrogen gases as transmutation products. The helium follows a production rate of ~9.8 appm/dpa, while environmental factors complicate hydrogen production obscuring an exact H/dpa ratio. Irradiation-induced dislocation loops, nano-cavities, solute clusters, and microsegregation were all observed. The dislocation loops and nano-cavities indicated saturation at 41 dpa. The solute clusters continued to evolve with Ni-Si clusters formed at 41 dpa, and Ni-Si-Mn-P clusters formed at 74 and 100 dpa, but neither clusters exhibited distinct diffraction patterns at any damage levels. Solute clusters were observed to frequently be co-located with dislocation loops, but fully decorated loops were rarely detected. Significant radiation-induced segregation (RIS) was observed around grain boundaries at all damage levels. The modified inverse Kirkendall (MIK) model captured the RIS behavior of major elements. Large cavities within or around an Mn-S rich region were observed for the first time. Through all the damage levels, void swelling is always below 0.05%, making significant dimensional change unlikely in core internals when used at similar conditions. Meanwhile, the role of overwhelming nanocavities, presumably helium bubbles, should be considered in other potential degradation mechanisms, including irradiation-assisted stress corrosion cracking, embrittlement, and loss of fracture toughness, which remain the concerns for extended operation of nuclear power plants.

Post Irradiation Examination, Isotope Dilution Mas↗
DOE OSTI2020

Redistribution of radionuclides in irradiated AGR-1 UCO TRISO fuel after 1800 °C safety testing

Release of radionuclides from intact tristructural-isotropic (TRISO) coated particle fuel at normal and accident conditions is a primary metric of fuel performance. The distribution of fission products and actinides in the TRISO layers of individual particles provides insight on radionuclide transport and release behavior and was determined using scanning electron microscopy analysis. Particles were isolated from an irradiated fuel compact (AGR-1 Compact 4-4-2) and analyzed as-irradiated or after individual particle safety-testing at 1800 °C for 650 h. Particles were selected for comparison based on their remaining 110mAg fission product inventory. These comparisons corroborated the observation that the 110m Ag inventory is a marker for relative irradiation temperature based on observed radionuclide distribution in the SiC layer. The comparison also indicated that the in-pile behavior influences the fission product and actinide species interactions with the TRISO layers during high temperature exposure after irradiation. The analysis confirms both palladium and uranium diffusion, as well as other species, are active in the UCO TRISO fuel system at 1800 °C and that palladium transport is active at lower temperatures relative to uranium. While diffusion across the SiC layer was observed, the intact nature of the SiC layer after the 1800 °C, 650-h exposure indicates the SiC layer maintained its functionality as a fission product barrier by mitigating release of radionuclides at beyond accident margin temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Structure of the pellet-cladding interaction layer of a high-burnup Zr-Nb-O nuclear fuel cladding

Here, structure of the pellet/cladding-interaction (PCI) layer of a high-burnup nuclear fuel with niobium-bearing cladding was investigated using modern transmission electron microscopy (TEM) techniques. Morphology of the PCI consisted of uniform zirconia layer on the cladding side and finger-like features towards to the ceramic fuel. The PCI layer showed a complex microstructure that constitutes three distinct zirconia layers formed by two zirconia phases. From cladding to fuel, monoclinic, tetragonal, and another tetragonal phase were determined via TEM diffraction patterns and precession electron diffraction (PED) using ASTAR microscopy platform (AMP). Characterizations showed that monoclinic and tetragonal phases close to the cladding were crack-free, but the tetragonal layer adjacent to the fuel contained cracks and pores. Presence of the monoclinic layer suggested that its formation involved the gaseous diffusion of oxygen below threshold dose of fission product damage before the fuel/cladding contact occurred. Furthermore, high-resolution TEM revealed compound phase of (U,Zr)O 2 at fringes of zirconia fingers on the fuel side.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Phase stability and microstructure of neutron-irradiated substoichiometric yttrium dihydrides

The impact of the neutron-displacement damage on phase stability and microstructure of substoichiometric yttrium dihydrides (YH x , x <2) were investigated to assess their use as solid moderator in high-temperature nuclear reactors. YH x specimens were, thus, subjected to neutron irradiations in the range of 0.1–2 displacements per yttrium atom (dpa-Y) in the temperature range of 536–878°C at the Oak Ridge National Laboratory's (ORNL's) High Flux Isotope Reactor (HFIR). YH x specimens were initially prepared at stoichiometry (H/Y) ratios of 1.69 and 1.83. HFIR-irradiated specimens were characterized by variety of techniques to investigate H retention characteristics including dimensional analysis, optical microscopy, scanning electron microscopy electron back scatter diffraction (EBSD), transmission electron microscopy, thermal desorption spectroscopy (TDS), and high-energy x-ray diffraction (HE-XRD) characterizations. Overall, YH x exhibited notable structural and phase stability under short-term neutron-irradiation, except for the samples with significant silicon carbide (SiC) interaction at high doses and temperatures. Basic dimensional and mass measurements were misleading for accurate assessment of H retention, as confirmed by EBSD phase maps, XRD line profiles, and TDS signals. Thus, it was discussed that a robust H retention metric is needed to assess irradiated hydrides. Further, nanoscale cavities were observed as a result of the neutron irradiation in all samples. Although no clear impact of dose and irradiation temperature was determined, the initial H/Y ratio had an impact on the cavity number density where low H/Y specimens had high-resistance to cavity formation. The Y-vacancy cluster formation at the collision stage of the displacement cascade and their stabilization by H were considered to be the likely underlying mechanisms for the observed cavity microstructure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Through-thickness fracture behavior of neutron-irradiated nuclear graphite NBG-17 Using X-ray micro-CT

Achieving precise control over crack propagation in nuclear graphite and conducting quantitative analysis remain challenging. In this study, the through-thickness fracture behavior of pristine and neutron-irradiated (700 °C, ∼7 dpa) NBG-17 nuclear graphite was investigated using split-disc testing coupled with micro-computed tomography (micro-CT). A notably lower number of micropores was observed in the neutron-irradiated specimen. The fracture toughness of neutron-irradiated NBG-17 was measured to be 1.45 MPa√m, compared to 1.17 ± 0.05 MPa√m for the pristine specimen. In both materials, cracks were found to initiate at the filler–binder interface, and often correlated with microstructural features such as pores and thermal cracks. Crack bridging and deflections emerged as the primary toughening mechanisms in both unirradiated and irradiated NBG-17. However, compared with the pristine specimen, the cracks in the neutron-irradiated specimen were more likely to grow trans granularly, resulting in less deflected crack paths. The reduced micro-porosity and strengthened filler–binder boundaries were considered to be the cause of the observed differences in crack morphologies. In conclusion, this study provides a qualitative analysis of the fracture behavior of neutron-irradiated nuclear graphite in the absence of radiolytic oxidation.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical properties, strain hardening, and fracture behavior of ultrasonic additively manufactured Zircaloy-4 after low-temperature neutron irradiation

Ultrasonic additive manufacturing (UAM) is a solid-state, layer-by-layer advanced manufacturing process that has the potential to create custom spatially controlled composites with embedded wires and sensors for nuclear component manufacture. For this work, to assess the feasibility of using UAM for nuclear-relevant materials research, the technique was used to produce a 3.5-mm-thick Zircaloy-4 plate for irradiation testing. The UAM Zircaloy-4 specimens were irradiated in the High Flux Isotope Reactor at a target irradiation temperature of 117 °C to 2.9 displacements per atom (dpa) to assess differences in irradiation-hardening behavior as a function of alloy processing path. The UAM and reference baseplate (BP) materials increased in yield strength by 372±27 MPa and 346±21 MPa, respectively, and both suffered significant reductions in uniform and total elongation attributed to irradiation hardening at low-temperature. Although the materials had similar nanoscale defect structures, including nanoscale black dot/loop features and strain-induced dislocation channels, the UAM material’s processing-related defects resulted in accelerated strain localization and failure as demonstrated by lower post-irradiation uniform elongation of UAM specimens (0.5 %) compared to BP (1.5 %) material. The UAM material also showed considerable anisotropy in mechanical response due to crack propagation along weld boundaries, resulting in differences in strength & ductility when tested parallel and perpendicular to the prior UAM build orientation. Therefore, although the fundamental irradiation response of UAM-processed Zircaloy-4 was phenomenologically comparable to that of BP reference material, additional optimization of the UAM processing is needed to produce irradiation-resistant and nuclear-relevant materials.

Digital image correlation↗
DOE OSTI2026

The porosity surrounding carbides and second phase stringers in monolithic U-10Mo fuel plate after irradiation

Post-irradiation microstructure characterization plays an important role in qualifying the low-enriched uranium (LEU) monolithic U-10 wt%Mo plate-type fuel for United States high-performance research reactors (USHPRRs) program. Inhomogeneous features resulting from manufacturing and irradiation processes, including carbides, second phase stringers, and extensive void spaces caused by the combining of small porosities, may increase the risk of heat concentration in local regions of the fuel plate over the operating conditions. In this study, characteristics of carbides, stringers, and porosity after multiple levels of irradiation at varying fission densities were studied by electron microscopes to decipher the morphology of pores and the porosity evolution in U-10 wt%Mo. For carbides, the result shows that porosities start forming on UMo grain boundaries, then on UMo/carbides interfaces as the burn-up going higher. However, the porosities surrounding carbides grow larger than the ones on UMo grain boundaries. The porosities around the uranium carbides could interconnect to form larger void space. The study revealed that the void spaces larger than 5 µm were found around uranium carbides after high burnup, while no evidence was observed to support the similar voids formed near second phase stringers even though the size of the stringers (> 50 µm) was much larger than uranium carbides (< 20 µm). The evolution of porosities suggests that the formation of second phase stringers may not create more significant porosities compared to regular uranium carbides regions during fuel operating conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Irradiation performance of a U-7Mo in Al-Si matrix dispersion full-size fuel plate assembly

The Korea Atomic Energy Research Institute (KAERI) is leading the Ki-Jang Research Reactor (KJRR) project with the intent to develop a new reactor for medical isotope production and other nuclear research purposes. The KJRR core is designed to use high density fuel system where uranium alloyed with 7 wt% molybdenum (U-7Mo) particles are dispersed in a matrix of aluminum alloyed with 5 wt% silicon (Al-5Si) and clad in aluminum alloy 6061 (Al-6061) to form fuel plates. KAERI developed a fabrication facility to construct KJRR fuel assemblies and partnered with the Idaho National Laboratory (INL) to irradiate a full-size fuel assembly, with 21 total fuel plates, in the Advanced Test Reactor (ATR). Irradiation testing and subsequent Post Irradiation Exam (PIE) campaigns were performed successfully over a multi-year project. Monte Carlo neutronic calculations, coupling with a depletion code, were performed based on ATR’s as-run power history which showed that the highest power plate (plate 20) reached 83.1 % end-of-life (EOL) local burnup based on initial 235 U content. Additionally, finite element thermal modeling was performed based as-run power history which showed a beginning-of-life (BOL) peak local heat flux of 184 W/cm 2 . No anomalous fuel performance was observed during the irradiation and target test conditions were achieved. PIE showed favorable performance of the fuel assembly regarding all important phenomena. This paper describes the KJRR fuel assembly irradiation conditions and PIE data to support the conclusion that it performed well, without evidence of unexpected or problematic fuel performance, within an irradiation test designed to bound the KJRR design environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Role of Accelerated Burnup Irradiation Testing in Support of Accelerated Fuel Qualification

Accelerated fuel qualification has gained attention as a means to reduce the time needed to realize new nuclear fuel concepts and expand the operating windows of existing fuel forms. A key component of this approach is accelerated burnup irradiation testing. Although the concept of accelerated burnup has been familiar to the community for many decades, the specifics about how the increasing fission rate may be used as a qualification tool have not yet been elucidated. The present work provides a vision of how accelerated fission rate testing can enable accelerated fuel qualification. Technology readiness levels (TRLs) are reintroduced to demarcate the stages of traditional fuel qualification, and accelerated fuel qualification is presented in this context. The critical steps needed to achieve each TRL are reframed within the context of modern nuclear materials research and development, as revolutionary fuel concepts are more common than previous eras. The practical impacts of accelerated fuel qualification approaches as applied to contemporary fuel qualification efforts are illustrated. Examples are given to illustrate how accelerated burnup irradiations are being used currently and could be applied in the future to support qualification and licensure. Finally, outstanding challenges in the application of accelerated burnup methods to nuclear fuel qualification are summarized, with priority placed on understanding how fission rate impacts diffusion, microstructure evolution, and other critical mechanisms that dictate fuel performance.

Accelerated fuel qualification↗
DOE OSTI2022

Engineering & Microstructure Scale PIE Report on EBR-II X441A Metallic Fuel Pins for the MORPH Experiment

The objectives of this project are to increase fundamental understanding of irradiation induced metallic U-Pu-Zr fuel behavior and to obtain data needed for the development of irradiation models for metallic fuels in MARMOT. The requested metallic fuel pins are from the X441A experiment irradiated in Experimental Breeder Reactor (EBR)-II and will be provided by the PIs for the duration of the experiment. The purpose of the pins irradiated in the X441A assembly was to vary Zr composition and fuel slug diameter in order to provide data for the metallic fuel performance code “LIFEMETAL” [ANL-IFR-125]. The fuels of interest to this project are metallic fuels with several Zr compositions (in wt.%): U-19Pu-6Zr, U-19Pu-10Zr, and U-19Pu-14Zr, which were irradiated to a peak burnup of approximately 11 at.%. The cladding was the same for all three fuel pins (austenitic stainless steel D9), which allows investigation of fuel-cladding interaction (FCI) phenomena. Varying Zr content in fuel pins enables investigation of the effect of Zr on fuel restructuring and fuel-cladding compatibility. Engineering and microstructure scale PIE activities will be focused on investigation of fundamental aspect of fuel performance such as species diffusion and migration, fission product behavior, and constituent redistribution. Obtained microstructural information will be used as the basis for the development of MARMOT models of U-Pu-Zr fuel performance at the mesoscale. Experimental data obtained through this proposal will be used to provide this fundamental understanding which will serve as the foundation of the development of radiation models for U-Pu-Zr in MARMOT. It will also provide a starting point for the design of new experiments to provide data for the validation of these MARMOT models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Gamma Discriminating Scintillation Screens for Digital Transfer Method Neutron Imaging

A collaborative project between Idaho National Laboratory (INL) and Paul-Scherrer Institute (PSI) is investigating a new type of scintillation screen that uses ZnS scintillator material with a dysprosium neutron converter instead of traditional prompt converters such as 6Li. Such a screen exposed to a neutron beam creates a latent image by neutron activation of the dysprosium in the scintillator screen. The activated screen is transported into a camera box allowing the camera to read a digital image from the photons emitted by the activated scintillation screen. Such an imaging system combines modern camera-based system architecture with the approach of traditional indirect transfer method radiography. The results show for the first time that the combination of dysprosium with a scintillation material like ZnS can produce light which is measurable under common camera-based detection conditions and that neutron radiographic images of reasonable quality can be produced. The resolution was poorer than expected at ~ 300 µm, but is on the order of the desired resolution of 100 µm. Potential improvements and additional converter materials may be investigated in the future that could increase the light output and improve spatial resolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Advanced Microscopy Report on UCO Fuel Kernels from Selected AGR-1 and AGR-2 Experiments

A variety of neutron irradiation experiments were completed at Idaho National Laboratory (INL) on tristructural isotropic (TRISO) coated particles contained in a graphitic matrix as part of the Advanced Gas Reactor (AGR) fuel development and qualification program. Although the initial advanced microscopy and microanalysis studies on AGR-1 particles focused predominantly on the SiC layer?s role as the main fission-product containment, studies were further expanded to evaluate UCO kernels of selected AGR-1 and AGR-2 coated particles. Fuel kernels tested in the AGR-1 and AGR-2 experiments is composed of a mixture of UO2 and UC, with a nominal as-fabricated stoichiometry of UO1.37 C0.35 and UO1.43 C0.39, respectively. These as-fabricated kernel-stoichiometry values are determined at the completion of kernel fabrication and do not account for any changes that will occur during the subsequent coating and compacting processes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Panel Session 145: Challenges and Opportunities in Establishing a System for Transportation of SNF/UNF

Issues associated with establishing a SNF Transportation System in the U.S. are complex. In part, this is because in the US when discussing SNF, there are two distinct categories. The two categories represent significant differences in ownership, transportation-regulator, and even the physical characteristics of the SNF. Specifically, the physical differences in the SNF include size of the rods, associated quantities to be shipped, cladding material, and radionuclide content/enrichment. The first is commercial SNF (i.e., that associated with nuclear power plants), owned by utilities, until a permanent repository is built with DOE obligated by law to then assume the responsibility for shipping and ownership of the SNF. Since no-permanent repository currently exists, most commercial SNF is stored near the reactor in which it was installed, hence requiring no shipments. Although current shipments of commercial SNF are very limited, the few that do occur are generally performed to support a utilities SNF consolidation effort utility and for post irradiation examination/testing. However, with approximately 83,000 metric tons currently being stored at more than 70 sites around the U.S., when a permanent repository becomes available, the required number of shipments will be extensive. The second category is DOE and research reactor fuel. These fuel rods are generally much smaller in length than commercial fuel rods, with the quantity of rods transported in a shipment significantly less than the number of rods in a typical commercial fuel assembly. Currently, most of the SNF shipments within the U.S come from this category. DOE is currently managing about 2500 metric tons of heavy metal of SNF. This panel focused on updates and status of transportation of SNF/UNF. Panelists provided updates and information on continuing impacts, risk assessment, equipment (rail cars, handling, securement), possible rail routing, and proposed inspection equipment/routing prior to shipments. Panelists with presentations: Preparing for Nuclear Waste Transportation (Daniel Ogg); Challenges and Opportunities in Establishing a System for Transportation of SNF/UNF (Kathy Langan); UNF Transportation: Challenges and Opportunities (Michael Valenzano)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Measurements of Irradiated Low Enriched Fuel with a Gamma-Ray Scanning System (ANIMMA 2023 Conference Presentation)

A gamma-ray scanning system was designed to perform post-irradiation measurements of nuclear fuel at Idaho National Laboratory (INL). The system is composed of a coaxial high-purity germanium (HPGe) detector, a collimator, and mechanical positioning stages that translate the fuel sample across the front of the collimator. A Monte Carlo N-Particle code simulation of the system and the fuel were created with vendor-supplied design specifications, dimensional measurements, and x-ray radiographs of the HPGe detector as well as all available fuel specifications. Benchmark measurements were performed by scanning an irradiated fuel rodlet containing eight pellets of 0.74% enriched UO2 in zirconium alloy. This fuel rodlet was part of the Environment Rodlet Transient Test Apparatus (SERTTA) testing campaign in the Transient Reactor Test Facility (TREAT). These results were compared to simulated spectra to help characterize the detector model and establish fidelity. One goal of the system is to determine the number of fissions per gram of UO2 in the fuel. This article documents the modeling, benchmarking measurements, and the calculated number of fissions per gram in the SERTTA-A rodlet which was previously irradiated at TREAT.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

POST-TEST EXAMINATIONS OF A LOCA SAMPLE FROM AN IRRADIATED HIGH-BURNUP PWR M5 FUEL ROD

A LOCA integral test with high burnup PWR M5 fuel rod was conducted in the Irradiated Fuel Examination Laboratory through the complete LOCA sequence: heating the LOCA sample to 300ºC and pressurizing the internal pressure to 8.27 MPa, heating at 5ºC/s from 300 to 1200ºC, holding in steam for 90s at 1200ºC, cooling at 3ºC/s to 800ºC, followed by water quench and rapid cooling to 100ºC. After LOCA testing, examinations, such as the fuel fragmentation analysis, burst and ballooning characterization, axial strain measurement, and microstructural examinations were performed. Metallographic examinations of an as-irradiated high burnup sample adjacent to the LOCA test sample revealed a bonding layer between the fuel and cladding. The posttest LOCA examinations indicates the corrosion layer formed during normal operations in the commercial reactor might provide a protection against the steam oxidation at high temperatures for test times performed in this work. The microstructure of the as-irradiated fuel is compared to the microstructure of the post-LOCA test fuel. Posttest LOCA examination on unirradiated post-tests Zr cladding samples was conducted, which served as baseline data for in cell testing with irradiated samples. The results obtained with irradiated PWR high burnup M5 fuel rad were compared to the LOCA test data obtained with irradiated BWR high burnup Zircaloy-2 fuel rod at Argonne national Laboratory.

Yan, Yong↗
DOE OSTI2025

Characterization of the microstructure of yttrium hydride under proton irradiation

High moderation per unit volume solid moderator materials like yttrium hydride (YH x ) are necessary for compact nuclear microreactors. However, the phase stability and hydrogen transport processes of YH x under high-temperature irradiation are largely unknown. Proton irradiation was conducted on YH x at 300 °C and 580 °C to 0.2 dpa using 1 MeV or 2 MeV protons in a high-vacuum environment. The hydrogen concentration was determined before and after irradiation using elastic recoil detection analysis, and microstructural evolution was examined via post-irradiation scanning transmission electron microscopy and Raman spectroscopy. Dislocation loops and cavities were observed in all conditions; their distribution was correlated with the bombarding proton energy and ion irradiation temperature. This work revealed that hydrogen retention is proportional to the formation of traps for hydrogen gas atoms and identified pathways for hydrogen release. The relative contributions of bulk or fast diffusion paths, such as grain boundaries, delamination boundaries, and stacking faults are discussed; the primary mechanisms of hydrogen loss are likely based on diffusion, ruling out artefacts of the experimental design. In conclusion, the study suggests proton irradiation may be a strong surrogate to study hydrogen transport in hydride moderator materials under irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗