Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process variable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Hydrothermal Synthesis and Analysis of Iodine-Containing Sodalite - 16153

Five process variables affecting hydrothermal synthesis of iodide sodalite, Na{sub 8}Al{sub 6}Si{sub 6}O{sub 24}I{sub 2}, were investigated, including NaOH concentration, aging time, temperature, Al/Si ratio, and precursor concentration. X-ray powder diffraction was performed to characterize synthesized samples, and Rietveld refinement method was used to quantify the mass fractions of phases. Iodide sodalite yield increased, in general, as NaOH concentration, aging time, and temperature increased. Lowering the Al/Si ratio from 1 to 0.5 increased the formation of cancrinite. Diluting the precursor concentration in the mixed solution with water revealed that nepheline hydrate-1, a zeolite, formed rather than sodalite. This observation, along with the preferential formation of zeolite A in samples where no NaOH was added, suggests that mechanisms for transport of the ions and formation of the aluminosilicate frameworks vary with hydrothermal conditions. The model for the best synthesis conditions based on the four significant variables is presented. (authors)

36 MATERIALS SCIENCE↗

Roll Compaction of Powdered Radioactive Wastes - 18251

Most of low- and intermediate-level radioactive wastes must be solidified by a proper binding matrix and disposed at the centralized disposal site. So it is desirable to achieve a high loading of radwastes in a drum to reduce the disposal fee while meeting both the national regulations and the waste acceptance criteria of the disposal site. In general, the radioactive wastes (liquid, dried powder and sludge) were solidified by mixing with a proper binding matrix (cement, polymer, asphalt, etc.), but their solidified volume inevitably increases due to the limitation of incorporating of radwaste into a binding matrix. To solve this problem, some Korean NPPs operate both a CTS (Concentrate Treatment System, evaporation and granulation) and a polymer solidification system. The size distribution of granulated wastes produced by CTS is so broad (diameter; several μm ∼ several cm) that a polymer cannot impregnate the void space between particles due to their small size. However, if the powdered radwaste can be compacted into high density pellets, and the pellets can be loaded in a drum with maximum waste loading, then the binding matrix can fill the void between pellets, it might be more desirable to keep the size distribution of pellets constant to reduce the solidified waste volume. This compaction methodology can greatly reduce the disposal fee due to the reduction of the solidified waste volume, and can facilitate polymer solidification due to the constant size of the radwaste pellets. This methodology is also applicable to solidify powdered wastes such a depleted uranium used as a catalyst, ash and sludge. Loading radwaste compacted with bentonite pellets versus particles into a container serves, as an engineered or natural barrier in a deep geologic disposal system. Roll compaction is a typical agglomeration process for dry powders and depends on the device parameters and the material properties. This study, firstly, was focused on the design of roll compactor (briquetting machine), the shape and size of pellet, and secondly the loading method of pellets into a drum, their solidification in polymer, and evaluating the overall volume reduction. We used bentonite (particle size; 85 ∼ 100 μm) as a material to be compacted instead of radwaste powders (concentrates and depleted uranium wastes) without the addition of agglomeration agents. In the design of roll, we considered the diameter (200 mm) and width (41 mm) of roll, two types of pocket shapes (< 9 mm, 0.275 ml), and the surface of the pocket. Fig. 2 shows two pellet shapes, tetragonal and circular. The pressure of roll compactor, one of the main process variables, is > 320 kg f/cm{sup 2}, and the roll gap is 0.5 mm. The powders are compacted in a compaction zone between two counter-rotating rolls according to the complicated mechanisms. As a result of the state and the apparent density of the pellets obtained by changing the pressure from 0 to 286 kg f/cm{sup 2}, the pellets were unstable at pressure=0, but above 148 kg f/cm{sup 2} the pellets were more stable, and the apparent density of the pellets was 2.63 g/cm{sup 3} at 148 kg f/cm{sup 3}, and 2.68 g/cm{sup 3} at 286 kg f/cm{sup 2}. The roller speed (rpm) can determine the capacity (kg/h) of a compactor, and depends on both the compaction pressure and the feeding rate. By increasing the roll speed from 2 to 4 rpm, the apparent density of pellets was decreased gradually from 2.74 g/cm{sup 3} to 1.45 g/cm{sup 3}. We designed the special feeding system in order to feed powders uniformly to the roll gripping zone and to supply powders into the narrowest part of the roll gap. At a constant roll speed (3 rpm) and a constant compaction pressure (286 kg f/cm{sup 2}), the apparent density of the pellets was linearly proportional to the feeding rate from 2.18 to 2.74 g/cm{sup 3} by changing the feeding rate of powders from 8 to 12 rpm. In the polymer solidification of the obtained pellets, we used epoxy resin as a solidification agent, and showed their solidified waste forms in Fig. 5. The incorporation ratio (wt.%) of powders/polymer was about 71.7/28.3 in tetragonal pellets, 71.9/28.1 in circular pellets. We calculated the volume reduction in an aspect of powders itself and the solidified waste form. In powder case, through the comparison of the apparent density of the obtained pellets (2.74 g/cm{sup 3}) and raw powders (0.93 g/cm{sup 3}), the volume reduction was calculated as about 2.74/0.93 = 2.95 times. This means that powders can be compacted to 1/2.95 times. And in waste form case, the weight ratio of powder/polymer in a mixing method (workable) and a compaction method is about 0.42, 2.56, individually. Therefore the volume reduction was calculated as about 2.56/0.42 = 6.01 times. We found a compaction methodology for the volume reduction of powdered radioactive wastes, and their polymer solidification will be more effective to reduce the volume of radwastes to be disposed. After a characterization of the solidified waste form incorporated pellets (including sintered pellets), this methodology will be applied to treat depleted uranium wastes used as catalyst, and to solve the problem of NPPs' polymer solidification system, as mentioned above. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Technetium-99 Behavior in Low-Temperature, Low-Pressure Evaporation Systems at the Hanford Site - 18461

This paper seeks to provide a technical basis for predicting the behavior of Technetium-99 (Tc-99) in the Effluent Management Facility (EMF) evaporator during the Direct Feed Low-Activity Waste (DFLAW) mission at the Hanford Site. This is done by using the 242-A Evaporator and the DM10 Melter System evaporator as analogues for the predicted design and operating strategy of the EMF evaporator. The focus of this investigation is to establish how Tc-99 behavior coincides with the behavior of several process variables (e.g. feed Tc-99 concentrations, feed sources, extent of evaporative concentration) associated with low-temperature, low-pressure evaporator operations. The primary measure of Tc-99 behavior was the partitioning of Tc-99 from the feed stream into the condensate stream (i.e. boil-off) of the evaporators. Analysis of 242-A and DM10 Melter System evaporator data allowed for the identification of the following trends regarding Tc-99 behavior in low-temperature, low-pressure evaporator systems: Tc-99 partitions minimally from the feed to the condensate stream and Tc-99 partitions consistently across a variety of operating and feed conditions. Given the similarities in design and operating strategies between the studied evaporator systems and the EMF evaporator, it is reasonable to suggest that these trends can be used to aid in planning for future EMF operations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Security-informed safety: integrating security within the safety demonstration of a smart device - 157

Safety and security engineering have, over the years, developed their own regulations, standards, cultures, and practices. However, there's a growing realisation that security is closely connected to safety. Safety must be security-informed: if a safety-critical system isn't secure, it isn't safe. A safety demonstration is incomplete and unconvincing unless it considers security. In our work for government and industry, we have used the Claims, Arguments, Evidence (CAE) framework to analyse the impact of security on a safety justification or safety case and identified the significant changes needed to address security explicitly. This will impact the design and implementation process as well as the assurance and V and V approach. In this paper we discuss the impact of integrating security when developing a safety demonstration of a smart device. A smart device is an instrument, device or component that contains a microprocessor (and therefore contains both hardware and software) and is programmed to provide specialised capabilities, often measuring or controlling a process variable. Examples of smart devices include radiation monitors, relays, turbine governors, uninterruptible power supplies and heating ventilation, and air conditioning controllers. (authors)

42 ENGINEERING↗

Automating Anomaly Detection for Target systems at Spallation Neutron Source

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, produces the world’s most intense pulse neutrons beams. An accelerated proton beam is directed into a mercury target to generate neutrons via spallation. The target system accounted for over 40% of the overall downtime of the facility in 2022. Thus, early detection in anomalies in the target systems can enable taking corrective actions to avoid failures and reduce downtime. Fault prognostics and anomaly detection in accelerators, both at SNS and outside, has largely focused on the beam side. This paper presents one the first studies exploring leveraging machine learning to automate the detection of anomalies in the target system. The target system consists of over 30 different interconnected subsystems, and the present work focuses on the mercury process system as a use case. Analyzing data from 28 process variables from 2022 and 2023, tree-based and reconstruction-based algorithms are employed to detect anomalies in archived data. The algorithms detected previously unreported anomalies, several of which were deemed alert worthy by human experts, particularly those found by reconstruction-based algorithms. Using data from each production run in the accelerator increased the generalizability of the models in time. Efforts are now underway to implement a workflow for incorporating human feedback to update the models and evaluating performance on unseen data. The models will eventually be integrated into the existing System Tracking and Reliability system with a web interface for automated anomaly detection and reporting along with a pathway for incorporating human feedback for model updates.

Raj, Anant [ORNL] (ORCID:0000000306711244)↗

CONTROL AND DATA ACQUISITION IN A CYBER-PHYSICAL MIDSTREAM TESTBED

This thesis presents the development of a laboratory-scale cyber–physical midstream pipeline testbed designed to address this gap and support research in industrial control systems security. The platform integrates pumps, valves, sensors, programmable logic controllers (PLCs), and a human–machine interface (HMI) to emulate the monitoring and control architecture of real pipeline operations. The physical process is implemented as a closed-loop liquid circulation system designed to replicate flow behavior characteristic of midstream pipeline infrastructure. The testbed enables real-time data acquisition of key process variables, including flow rate and pressure facilitating the generation of datasets representative of normal pipeline operation. A threat model encompassing common ICS attack vectors was developed, including sensor spoofing, command injection, false data injection, denial-of-service attacks, and relay manipulation. Multiple attack scenarios were implemented and evaluated to demonstrate how cyber intrusions targeting sensors, actuators, networks, and software propagate into measurable physical consequences in pipeline flow and pressure. The developed platform serves as a practical, cost-effective environment for experimentation, education, and future cybersecurity research in midstream pipeline systems.

42 ENGINEERING↗

CODE ACCEPTANCE OF A NEW JOINING TECHNOLOGY FOR STORAGE CONTAINMENTS [REISSUE]

One of the activities associated with cleanup throughout the Department of Energy (DOE) complex is packaging radioactive materials into storage containers. Much of this work will be performed in high-radiation environments requiring fully remote operations, for which existing, proven systems do not currently exist. These conditions require a process that is capable of producing acceptable (defect-free) welds on a consistent basis; the need to perform weld repair, under fully-remote operations, can be extremely costly and time consuming. Current closure-welding technologies (fusion welding) are not well suited for this application and will present risk to cleanup cost and schedule. To address this risk, Fluor and the Pacific Northwest National Laboratory (PNNL) are proposing that a new and emerging joining technology, Friction Stir Welding (FSW), be considered for this work. FSW technology has been demonstrated in other industries (aerospace and marine) to produce near flaw-free welds on a consistent basis. FSW is judged capable of providing the needed performance for fully-remote closure welding of containers for radioactive materials for the following reasons: FSW is a solid-state process; material is not melted. FSW does not produce the type of defects associated with fusion welding, e.g., solidification-induced porosity, cracking, and distortion due to weld shrinkage. In addition, because FSW is a low-heat input process, material properties (mechanical, corrosion and environmental) experience less degradation in the heat affected zones than do fusion welds. When compared to fusion processes, FSW produces extremely high weld quality. FSW is performed using machine-tool technology. The equipment is simple and robust and well-suited for high radiation, fully-remote operations compared to the relatively complex equipment associated with fusion-welding processes. Additionally, for standard wall thicknesses of radioactive materials containers, the FSW process can perform the final closure in a single pass (GTAW requires multiple passes) resulting in increased productivity. The performance characteristics of FSW, Le., high weld quality, simple machine-tool equipment and increased welding efficiency, suggest that this new technology should be considered for radioactive materials packaging campaigns. FSW technology will require some development, adaptation for this application, along with several activities needed for commercialization. One of these activities will be to obtain approval from the governing construction code to use the FSW technology. The American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME B&PVC) will govern this work; however, rules for the use of FSW are not currently addressed. A code case will be required, defining appropriate process variables within prescribed limits, and submitted to the Code for review/approval and incorporation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multi-Device Knob Utility for LCLS

At the SLAC National Accelerator Laboratory (SLAC) the Controls Department (CD) has developed a new Multi-Device Knob Utility (MKB) based on the Experimental Physics and Industrial Control System (EPICS) toolkit for controlling one or more Process Variables (PVs) in unison, or simultaneously, from a physical knob located in the control room, or from various software tools such as the EPICS Extensible Display Manager (EDM) or a Swing slider in Java. A group of devices are hooked up to a knob, and then the value written to the devices is a simple function of the value of the knob. This is used, most commonly, to create a bump in the electron beam for the Linac Coherent Light Source (LCLS). Control system variables typically controlled are magnetic fields, phases, and timing offsets. This paper describes the technologies used to implement this utility.

43 PARTICLE ACCELERATORS↗

High Availability On-line Relational Databases for Accelerator Control and Operation

The role that relational database (RDB) technology plays in accelerator control and operation continues to grow in such areas as electronic logbooks, machine parameter definitions, and facility infrastructure management. RDBs are increasingly relied upon to provide the official 'master' copy of these data. Whereas the services provided by the RDB have traditionally not been 'mission critical', the availability of modern RDB management systems is now equivalent to that of standard computer file-systems. RDBs can be relied on to supply pseudo real-time response to operator and machine physicist requests. This paper describes recent developments in the IRMIS RDB project. Generic lattice support has been added, serving as the driver for model-based machine control. Abstract physics name service and process variable introspection has been added. Specific emphasis has been placed both on providing fast response time to accelerator operators and modeling code requests, as well as high (24/7) availability of the RDB service.

43 PARTICLE ACCELERATORS↗

JV Task 95-Particulate Control Consulting for Minnesota Ore Operations

The purpose of the project was to assist U.S. Steel in the evaluation, selection, planning, design, and testing of potential approaches to help meet U.S. Steel's goal for low-particulate matter emissions and regulatory compliance. The energy-intensive process for producing iron pellets includes treating the pellets in high-temperature kilns in which the iron is converted from magnetite to hematite. The kilns can be fired with either natural gas or a combination of gas and coal or biomass fuel and are equipped with wet venturi scrubbers for particulate control. Particulate measurements at the inlet and outlet of the scrubbers and analysis of size-fractionated particulate samples led to an understanding of the effect of process variables on the measured emissions and an approach to meet regulatory compliance.

01 COAL, LIGNITE, AND PEAT↗

Subsetted model output for process-tendency-related variables from a LASSO-CACTI WRF simulation

Process-tendency-related model output, mostly for the Thompson microphysics scheme (when used), from a Weather Research and Forecasting (WRF) simulation from the Large-Eddy Simulation (LES) Atmospheric Radiation Measurement (ARM) Symbiotic Simulation and Observation (LASSO) deep-convection scenario for the Cloud, Aerosol, and Complex Terrain Interactions (CACTI) field campaign. The LASSO-CACTI simulations span grid spacings from 7.5 km to 100 m for convection near the Sierras de Córdoba mountain range, roughly centered on the ARM Mobile Facility. More information can be found at https://www.arm.gov/capabilities/modeling/lasso. This version of the output is a collection of variables subsetted from the raw WRF output to reduce the file overhead for users not needing the full raw dataset. The subset files are in netCDF format with the height-based variables on the raw, model eta levels.

54 ENVIRONMENTAL SCIENCES↗

State estimation of an acid gas removal (AGR) plant as part of an integrated gasification combined cycle (IGCC) plant with CO2 capture

An accurate estimation of process state variables not only can increase the effectiveness and reliability of process measurement technology, but can also enhance plant efficiency, improve control system performance, and increase plant availability. Future integrated gasification combined cycle (IGCC) power plants with CO2 capture will have to satisfy stricter operational and environmental constraints. To operate the IGCC plant without violating stringent environmental emission standards requires accurate estimation of the relevant process state variables, outputs, and disturbances. Unfortunately, a number of these process variables cannot be measured at all, while some of them can be measured, but with low precision, low reliability, or low signal-to-noise ratio. As a result, accurate estimation of the process variables is of great importance to avoid the inherent difficulties associated with the inaccuracy of the data. Motivated by this, the current paper focuses on the state estimation of an acid gas removal (AGR) process as part of an IGCC plant with CO2 capture. This process has extensive heat and mass integration and therefore is very suitable for testing the efficiency of the designed estimators in the presence of complex interactions between process variables. The traditional Kalman filter (KF) (Kalman, 1960) algorithm has been used as a state estimator which resembles that of a predictor-corrector algorithm for solving numerical problems. In traditional KF implementation, good guesses for the process noise covariance matrix (Q) and the measurement noise covariance matrix (R) are required to obtain satisfactory filter performance. However, in the real world, these matrices are unknown and it is difficult to generate good guesses for them. In this paper, use of an adaptive KF will be presented that adapts Q and R at every time step of the algorithm. Results show that very accurate estimations of the desired process states, outputs or disturbances can be achieved by using the adaptive KF.

97 MATHEMATICS AND COMPUTING↗

The Feedstock-Conversion Interface Consortium - Understanding and Mitigating the Impacts of Feedstock Variability in Bioconversion Processes

The Feedstock-Conversion Interface Consortium is led by DOE as a collaborative effort among researchers from 9 National Laboratories. The FCIC was formed because biomass feedstock properties are variable and different from other commodities, and empirical approaches to address these issues have been unsuccessful. The FCIC uses first-principles-based science to de-risk biorefinery scale-up and deployment by understanding and mitigating the impacts of feedstock variability on bioenergy conversion processes. In this presentation, we present a brief overview of key FCIC prinicples and recent results.

biomass↗

Heralded processes on continuous-variable spaces as quantum maps

Heralding processes, which only work when a measurement on a part of the system give the good result, are particularly interesting for continuous-variables. They permit non-Gaussian transformations that are necessary for several continuous-variable quantum information tasks. However if maps and quantum process tomography are commonly used to describe quantum transformations in discrete-variable space, they are much rarer in the continuous-variable domain. Also, no convenient tool for representing maps in a way more adapted to the particularities of continuous variables have yet been explored. In this paper we try to fill this gap by presenting such a tool.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Rolling Temperature on the Microstructure and Mechanical Properties of AZ31 Alloy Sheet Processed through Variable-Plane Rolling

AZ31 magnesium alloy sheet was produced through variable-plane rolling (VPRing) under different temperatures, and a conventional rolled AZ31 alloy was investigated for comparison. A basal texture was formed during these two processes. The texture intensity was closely related to dynamic recrystallization and deformation mechanism. Four types of twins appeared, namely {10-12} extension twins, {10-13} and {10-11} contraction twins and {10-11}-{10-12} double twins. High rolling temperature and rolling plane alteration were beneficial for activating {10-11}-{10-12} double twins. The tensile strengths revealed a declining trend with elevated rolling temperatures. The AZ31 alloy rolled at 573 K showed advantageous combination with a high yield strength of 286 MPa and compromised elongation of 5%. The mechanical anisotropy of VPRed AZ31 sheet decreased with nearly similar yield strengths along the roll direction (RD), transverse direction and 45° away from the RD. The VPRing process improved the rollability and strength of Mg alloy and reduced its mechanical anisotropy.

36 MATERIALS SCIENCE↗

Aerosol variability, synoptic‐scale processes, and their link to the cloud microphysics over the northeast Pacific during MAGIC

Abstract Shipborne aerosol measurements collected from October 2012 to September 2013 along 36 transects between the port of Los Angeles, California (33.7°N, 118.2°), and Honolulu, Hawaii (21.3°N, 157.8°W), during the Marine ARM GPCI (Global Energy and Water Cycle Experiment (GEWEX)‐Cloud System Study (GCSS)‐Pacific Cross‐section Intercomparison) Investigation of Clouds campaign are analyzed to determine the circulation patterns that modulate the synoptic and monthly variability of cloud condensation nuclei (CCN) in the boundary layer. Seasonal changes in CCN are evident, with low magnitudes during autumn/winter, and high CCN during spring/summer accompanied with a characteristic westward decrease. CCN monthly evolution is consistent with satellite‐derived cloud droplet number concentration N d from the Moderate Resolution Imaging Spectroradiometer. One‐point correlation ( r ) analysis between the 1000 hPa zonal wind time series over a region between 125°W and 135°W, 35°N and 45°N, and the N d field yields a negative r (up to −0.55) over a domain that covers a zonal extent of at least 20° from the California shoreline, indicating that N d decreases when the zonal wind intensifies. The negative r expands southwestward as the zonal wind precedes N d by up to 3 days, suggesting a transport mechanism from the coast of North America mediated by the California low‐coastal jet, which intensifies in summer when the aerosol concentration and N d reach a maximum. A first assessment of aerosol‐cloud interaction (ACI) is performed by combining CCN and satellite N d values from the Fifteenth Geostationary Operational Environmental Satellite. The CCN‐ N d correlation is 0.66–0.69, and the ACI metric defined as ACI = ∂ln( N d )/∂ln(CCN) is high at 0.9, similar to other aircraft‐based studies and substantially greater than those inferred from satellites and climate models.

Painemal, David↗

Radiative reverse shock laser experiments relevant to accretion processes in cataclysmic variables

We discuss the production of radiative reverse shocks in experiments at the Omega-60 laser facility. The ability of this high-intensity laser to impart large energy densities on micron-thin foils makes it feasible to create supersonic plasma flows. Obtaining a radiative reverse shock in the laboratory requires a sufficiently fast flow (∼100 km/s) of a material whose opacity is large enough to produce energetically significant emission from experimentally achievable shocked layers. The reverse shock forms in the flow once it is impeded. This paper presents the first radiographic data of normal incidence, reverse shockwaves. These experiments are primarily motivated by the contribution of radiative reverse shock waves to the evolving dynamics of the cataclysmic variable (CV) system in which they reside. We show similarity properties to suggest that the experimental production of radiative reserve shocks in the laboratory may be scalable to such astrophysical systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗