Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Order Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗
NASA NTRS2017

Aeroelastic Modeling of X-56A Stiff-Wing Configuration Flight Test Data

Aeroelastic stability and control derivatives for the X-56A Multi-Utility Technology Testbed (MUTT), in the stiff-wing configuration, were estimated from flight test data using the output-error method. Practical aspects of the analysis are discussed. The orthogonal phase-optimized multisine inputs provided excellent data information for aeroelastic modeling. Consistent parameter estimates were determined using output error in both the frequency and time domains. The frequency domain analysis converged faster and was less sensitive to starting values for the model parameters, which was useful for determining the aeroelastic model structure and obtaining starting values for the time domain analysis. Including a modal description of the structure from a finite element model reduced the complexity of the estimation problem and improved the modeling results. Effects of reducing the model order on the short period stability and control derivatives were investigated.

Grauer, Jared A.↗
NASA NTRSDate not supplied

Robotic Software Architecture for in-Space Outfitting Operations

Space exploration is expanding into longer missions, larger payloads, and more complex operations. To make these larger scale missions a reality, it is necessary to perform assembly, construction, and maintenance tasks via a robotic workforce in addition to crewed operations. While there has been significant research into in-space assembly and manufacturing, it is primarily focused on rigid structural elements, such as ISRU printing or truss construction. Outfitting tasks, such as cable routing, are a critical step to a fully operational in-space facility. This paper seeks to provide a reduced order state model and an optimized combination of state-of-the-art robotics algorithms applied to a cable routing scenario. Simulation results are expected to advance approaches to online autonomous robotic manipulation of non-rigid elements.

Amy M Quartaro↗
NASA NTRSDate not supplied

Robotic Software Architecture for In-Space Outfitting Operations

Space exploration is expanding into longer missions, larger payloads, and more complex operations. To make these larger scale missions a reality, it is necessary to perform assembly, construction, and maintenance tasks via a robotic workforce in addition to crewed operations. While there has been significant research into in-space assembly and manufacturing, it is primarily focused on rigid structural elements, such as ISRU printing or truss construction. Outfitting tasks, such as cable routing, are a critical step to a fully operational in-space facility. This paper seeks to provide a reduced order state model and an optimized combination of state-of-the-art robotics algorithms applied to a cable routing scenario. Simulation results are expected to advance approaches to online autonomous robotic manipulation of non-rigid elements.

Amy Quartaro↗
NASA NTRSDate not supplied

Blade Mistuning Analysis for Boundary Layer Inlet Flow Distortion-Tolerant Fan Blades

NASA Glenn Research Center has tested the BLI2DTF propulsor including the fan rotor. BLI2DTF stands for Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan. A comparison of the vibratory response between analysis results and experimental wind tunnel test results yielded reasonable agreement, yet some differences were noted. Blade mistuning effects have been identified as a potential cause for these differences. A tuned forced response analysis in a turbomachinery engine rotor system assumes that all of the blades are identical, so that the natural frequencies of individual blades are the same. In contrast to this assumption, the wind tunnel tests of the BLI2DTF rotor system revealed that the individual blade response frequencies varied. These variations in individual blade frequencies may be attributed to blade mistuning due to potential differences in the structural and material properties of individual blades. For an understanding of these variations, it is necessary to analyze the influence of blade mistuning on the BLI2DTF rotor system, which will provide a more precise assessment of its vibratory stresses and high cycle fatigue life. The purpose of the study was to investigate the influence of blade mistuning on the dynamic characteristics of this rotor system. At the same fan operation condition, a comparative forced response analysis was performed for both tuned and mistuned BLI2DTF rotor systems. A comparison of the results from these analyses found that the mistuning effects on the present BLI2DTF rotor system are notable. As a result, fan blade mistuning is to be considered a contributor to the levels of vibratory dynamic stresses observed during the wind tunnel experiment.

Blade mistuning↗
NASA NTRS1993

Reduction of Model Complexity by Active Control

The mathematical models of many dynamic systems of interest in the aerospace industry are inherently complex and of high order. Rather than grapple with the full-complexity models for such systems, the control designers often elect to derive low-order, reduced-complexity models for which a control system can be designed. The subject of model-order reduction has received a significant amount of attention in control engineering literature. This paper describes and demonstrates a novel active-control methodology that can be used to design a control system that automatically forces the original system to behave like a chosen reduced-complexity model by treating the effects of the original complexity-related terms as disturbances acting on the reduced-complexity system. The method is demonstrated by several worked examples involving both linear and nonlinear systems, supported by simulation results.

Bukley, Angelia P.↗
NASA NTRS1992

Vibration attenuation of the NASA Langley evolutionary structure experiment using H(sub infinity) and structured singular value (micron) robust multivariable control techniques

The use is studied of active control to attenuate structural vibrations of the NASA Langley Phase Zero Evolutionary Structure due to external disturbance excitations. H sub infinity and structured singular value (mu) based control techniques are used to analyze and synthesize control laws for the NASA Langley Controls Structures Interaction (CSI) Evolutionary Model (CEM). The CEM structure experiment provides an excellent test bed to address control design issues for large space structures. Specifically, control design for structures with numerous lightly damped, coupled flexible modes, collocated and noncollocated sensors and actuators and stringent performance specifications. The performance objectives are to attenuate the vibration of the structure due to external disturbances, and minimize the actuator control force. The control design problem formulation for the CEM Structure uses a mathematical model developed with finite element techniques. A reduced order state space model for the control design is formulated from the finite element model. It is noted that there are significant variations between the design model and the experimentally derived transfer function data.

Balas, Gary J.↗
NASA NTRS1983

Pilot modeling and closed-loop analysis of flexible aircraft in the pitch tracking task

The issue addressed in the appropriate modeling technique for pilot vehicle analysis of large flexible aircraft, when the frequency separation between the rigid-body mode and the dynamic aeroelastic modes is reduced. This situation was shown to have significant effects on pitch-tracking performance and subjective rating of the task, obtained via fixed base simulation. Further, the dynamics in these cases are not well modeled with a rigid-body-like model obtained by including only 'static elastic' effects, for example. It is shown that pilot/vehicle analysis of this data supports the hypothesis that an appropriate pilot-model structure is an optimal-control pilot model of full order. This is in contrast to the contention that a representative model is of reduced order when the subject is controlling high-order dynamics as in a flexible vehicle. The key appears to be in the correct assessment of the pilot's objective of attempting to control 'rigid-body' vehicle response, a response that must be estimated by the pilot from observations contaminated by aeroelastic dynamics. Finally, a model-based metric is shown to correlate well with the pilot's subjective ratings.

Schmidt, D. K.↗
NASA NTRS1997

Substructure System Identification for Finite Element Model Updating

This report summarizes research conducted under a NASA grant on the topic 'Substructure System Identification for Finite Element Model Updating.' The research concerns ongoing development of the Substructure System Identification Algorithm (SSID Algorithm), a system identification algorithm that can be used to obtain mathematical models of substructures, like Space Shuttle payloads. In the present study, particular attention was given to the following topics: making the algorithm robust to noisy test data, extending the algorithm to accept experimental FRF data that covers a broad frequency bandwidth, and developing a test analytical model (TAM) for use in relating test data to reduced-order finite element models.

Craig, Roy R., Jr.↗
NASA NTRS1990

Practical model reduction for flexible structures

The most accepted methods for developing models of flexible structures for the analysis, design and simulation of control systems are finite element methods and extraction from experimental data. Using either of these methods, models are often produced with modes that do not significantly add to the fidelity of the model. This paper presents techniques for eliminating these modes. Particular attention is paid to multiple-input, multiple-output systems. First, control system models developed for flexible structures, using finite element methods and experimental data, are briefly discussed. the shortcomings of using models with unnecessary and/or residual modes are delineated. Then, two techniques for reducing the order of models are presented; the first is applicable to single-input, single-output systems and the second for multiple-input, multiple-output systems. Finally, both are illustrated using model data from the proposed NASA Shuttle-C.

Mitchell, Jerrel R.↗
NASA NTRS1987

Modeling and control of beam-like structures

The most popular finite element codes are based upon appealing theories of convergence of modal frequencies. For example, the popularity of cubic elements for beam-like structures is due to the rapid convergence of modal frequencies and stiffness properties. However, for those problems in which the primary consideration is the accuracy of response of the structure at specified locations it is more important to obtain accuracy in the modal costs than in the modal frequencies. The modal cost represents the contribution of a mode in the norm of the response vector. This paper provides a complete modal cost analysis for beam-like continua. Upper bounds are developed for mode truncation errors in the model reduction process and modal cost analysis dictates which modes to retain in order to reduce the model for control design purposes.

Hu, A.↗
NASA NTRS1988

Modal cost analysis for simple continua

The most popular finite element codes are based upon appealing theories of convergence of modal frequencies. For example, the popularity of cubic elements for beam-like structures is due to the rapid convergence of modal frequencies and stiffness properties. However, for those problems in which the primary consideration is the accuracy of response of the structure at specified locations, it is more important to obtain accuracy in the modal costs than in the modal frequencies. The modal cost represents the contribution of a mode in the norm of the response vector. This paper provides a complete modal cost analysis for simple continua such as beam-like structures. Upper bounds are developed for mode truncation errors in the model reduction process and modal cost analysis dictates which modes to retain in order to reduce the model for control design purposes.

Hu, A.↗
NASA NTRS2023

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗
NASA NTRS2023

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗
NASA NTRS1990

Structural mode significance using INCA

Structural finite element models are often too large to be used in the design and analysis of control systems. Model reduction techniques must be applied to reduce the structural model to manageable size. In the past, engineers either performed the model order reduction by hand or used distinct computer programs to retrieve the data, to perform the significance analysis and to reduce the order of the model. To expedite this process, the latest version of INCA has been expanded to include an interactive graphical structural mode significance and model order reduction capability.

Bauer, Frank H.↗