SEARCH · Search NASA

Results for “Reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Mechanisms of Active Aerodynamic Load Reduction on a Rotorcraft Fuselage With Rotor Effects

The reduction of the aerodynamic load that acts on a generic rotorcraft fuselage by the application of active flow control was investigated in a wind tunnel test conducted on an approximately 1/3-scale powered rotorcraft model simulating forward flight. The aerodynamic mechanisms that make these reductions, in both the drag and the download, possible were examined in detail through the use of the measured surface pressure distribution on the fuselage, velocity field measurements made in the wake directly behind the ramp of the fuselage and computational simulations. The fuselage tested was the ROBIN-mod7, which was equipped with a series of eight slots located on the ramp section through which flow control excitation was introduced. These slots were arranged in a U-shaped pattern located slightly downstream of the baseline separation line and parallel to it. The flow control excitation took the form of either synthetic jets, also known as zero-net-mass-flux blowing, and steady blowing. The same set of slots were used for both types of excitation. The differences between the two excitation types and between flow control excitation from different combinations of slots were examined. The flow control is shown to alter the size of the wake and its trajectory relative to the ramp and the tailboom and it is these changes to the wake that result in a reduction in the aerodynamic load.

Schaeffler, Norman W.↗

NASA NTRS2016

Experimental Study of Wake / Flap Interaction Noise and the Reduction of Flap Side Edge Noise

The effects of the interaction of a wake with a half-span flap on radiated noise are examined. The incident wake is generated by bars of various widths and lengths or by a simplified landing gear model. Single microphone and phased array measurements are used to isolate the effects of the wake interaction on the noise radiating from the flap side edge and flap cove regions. The effects on noise of the wake generator's geometry and relative placement with respect to the flap are assessed. Placement of the wake generators upstream of the flap side edge is shown to lead to the reduction of flap side edge noise by introducing a velocity deficit and likely altering the instabilities in the flap side edge vortex system. Significant reduction in flap side edge noise is achieved with a bar positioned directly upstream of the flap side edge. The noise reduction benefit is seen to improve with increased bar width, length and proximity to the flap edge. Positioning of the landing gear model upstream of the flap side edge also leads to decreased flap side edge noise. In addition, flap cove noise levels are significantly lower than when the landing gear is positioned upstream of the flap mid-span. The impact of the local flow velocity on the noise radiating directly from the landing gear is discussed. The effects of the landing gear side-braces on flap side edge, flap cove and landing gear noise are shown.

Hutcheson, Florence V.↗

NASA NTRS2016

Potential for Landing Gear Noise Reduction on Advanced Aircraft Configurations

The potential of significantly reducing aircraft landing gear noise is explored for aircraft configurations with engines installed above the wings or the fuselage. An innovative concept is studied that does not alter the main gear assembly itself but does shorten the main strut and integrates the gear in pods whose interior surfaces are treated with acoustic liner. The concept is meant to achieve maximum noise reduction so that main landing gears can be eliminated as a major source of airframe noise. By applying this concept to an aircraft configuration with 2025 entry-into-service technology levels, it is shown that compared to noise levels of current technology, the main gear noise can be reduced by 10 EPNL dB, bringing the main gear noise close to a floor established by other components such as the nose gear. The assessment of the noise reduction potential accounts for design features for the advanced aircraft configuration and includes the effects of local flow velocity in and around the pods, gear noise reflection from the airframe, and reflection and attenuation from acoustic liner treatment on pod surfaces and doors. A technical roadmap for maturing this concept is discussed, and the possible drag increase at cruise due to the addition of the pods is identified as a challenge, which needs to be quantified and minimized possibly with the combination of detailed design and application of drag reduction technologies.

Thomas, Russell H.↗

NASA NTRS2017

Brushing Your Spacecrafts Teeth: A Review of Biological Reduction Processes for Planetary Protection Missions

Much like keeping your teeth clean, where you brush away biofilms that your dentist calls "plaque," there are various methods to clean spaceflight hardware of biological contamination, known as biological reduction processes. Different approaches clean your hardware's "teeth" in different ways and with different levels of effectiveness. We know that brushing at home with a simple toothbrush is convenient and has a different level of impact vs. getting your teeth cleaned at the dentist. In the same way, there are some approaches to biological reduction that may require simple tools or more complex implementation approaches (think about sonicating or just soaking your dentures, vs. brushing them). There are also some that are more effective for different degrees of cleanliness and still some that have materials compatibility concerns. In this article, we review known and NASA-certified approaches for biological reduction, pointing out materials compatibility concerns and areas where additional research is needed.

Pugel, D. E. (Betsy)↗

NASA NTRS2017

Brushing Your Spacecrafts Teeth: A Review of Biological Reduction Processes for Planetary Protection Missions

Much like keeping your teeth clean, where you brush away biofilms that your dentist calls plaque, there are various methods to clean spaceflight hardware of biological contamination, known as biological reduction processes. Different approaches clean your hardwares teeth in different ways and with different levels of effectiveness. We know that brushing at home with a simple toothbrush is convenient and has a different level of impact vs. getting your teeth cleaned at the dentist. In the same way, there are some approaches to biological reduction that may require simple tools or more complex implementation approaches (think about sonicating or just soaking your dentures, vs. brushing them). There are also some that are more effective for different degrees of cleanliness and still some that have materials compatibility concerns. In this article, we review known and NASA-certified approaches for biological reduction, pointing out materials compatibility concerns and areas where additional research is needed.

Pugel, D.E. (Betsy)↗

NASA NTRS2016

Global and Regional Radiative Forcing from 20 Reductions in BC, OC and SO4 an HTAP2 Multi-Model Study

In the Hemispheric Transport of Air Pollution Phase 2 (HTAP2) exercise, a range of global atmospheric general circulation and chemical transport models performed coordinated perturbation experiments with 20% reductions in emissions of anthropogenic aerosols, or aerosol precursors, in a number of source regions. Here, we compare the resulting changes in the atmospheric load and vertically resolved profiles of black carbon (BC), organic aerosols (OA) and sulfate (SO4/ from 10 models that include treatment of aerosols. We use a set of temporally, horizontally and vertically resolved profiles of aerosol forcing efficiency (AFE) to estimate the impact of emission changes in six major source regions on global radiative forcing (RF) pertaining to the direct aerosol effect, finding values between. 51.9 and 210.8mW/sq m/Tg for BC, between -2.4 and -17.9mW/sq m/Tg for OA and between -3.6 and -10.3W/sq m/Tg for SO4. In most cases, the local influence dominates, but results show that mitigations in south and east Asia have substantial impacts on the radiative budget in all investigated receptor regions, especially for BC. In Russia and the Middle East, more than 80 % of the forcing for BC and OA is due to extra-regional emission reductions. Similarly, for North America, BC emissions control in east Asia is found to be more important than domestic mitigations, which is consistent with previous findings. Comparing fully resolved RF calculations to RF estimates based on vertically averaged AFE profiles allows us to quantify the importance of vertical resolution to RF estimates. We find that locally in the source regions, a 20% emission reduction strengthens the radiative forcing associated with SO4 by 25% when including the vertical dimension, as the AFE for SO4 is strongest near the surface. Conversely, the local RF from BC weakens by 37% since BC AFE is low close to the ground. The fraction of BC direct effect forcing attributable to intercontinental transport, on the other hand, is enhanced by one-third when accounting for the vertical aspect, because long-range transport primarily leads to aerosol changes at high altitudes, where the BC AFE is strong. While the surface temperature response may vary with the altitude of aerosol change, the analysis in the present study is not extended to estimates of temperature or precipitation changes.

profiles of aerosol forcing efficiency (AFE)↗

NASA NTRS2017

Effect of Off-Body Laser Discharge on Drag Reduction of Hemisphere Cylinder in Supersonic Flow

The interaction of an off-body laser discharge with a hemisphere cylinder in supersonic flow is investigated. The objectives are 1) experimental determination of the drag reduction and energetic efficiency of the laser discharge, and 2) assessment of the capability for accurate simulation of the interaction. The combined computational and experimental study comprises two phases. In the first phase, laser discharge in quiescent air was examined. The temporal behavior of the shock wave formed by the laser discharge was compared between experiment and simulation and good agreement is observed. In the second phase, the interaction of the laser discharge with a hemisphere cylinder was investigated numerically. Details of the pressure drag reduction and the physics of the interaction of the heated region with the bow shock are included. The drag reduction due to this interaction persisted for about five characteristic times where one characteristic time represents the time for the flow to move a distance equal to the hemisphere radius. The energetic efficiency of laser discharge for the case with 50 mJ energy absorbed by the gas is calculated as 3.22.

Kianvashrad, Nadia↗

NASA NTRS2017

Active Chevrons for Jet Noise Reduction

Jet noise is often a dominant component of aircraft noise, particularly at takeoff. To meet the stringent noise regulations, the aircraft industry is in a pressing need of advanced noise reduction concepts. In the present study, the potential of piezoelectrically-activated chevrons for jet noise reduction was experimentally investigated. The perturbations near the nozzle exit caused by piezoelectrically-activated chevrons could be used to modify the growth rate of the mixing layer and thereby potentially reduce jet noise. These perturbations are believed to increase the production of small-scale disturbances at the expense of large-scale turbulent structures. These large-scale turbulent structures are responsible for the dominant portion of the jet mixing noise, particularly low-frequency noise. Therefore, by exciting the static chevron geometry through piezoelectric actuators, an additional acoustic benefit could possibly be achieved. To aid in the initial implementation of this concept, several flat-faced faceted nozzles (four, six, and eight facets) were investigated. Among the faceted nozzles, it was found that the eight-faceted nozzle behaves very similarly to the round nozzle. Furthermore, among the faceted nozzles with static chevrons, the four-faceted nozzle with static chevrons was found to be most effective in terms of jet noise reduction. The piezoelectrically-activated chevrons reduced jet noise up to 2 dB compared to the same nozzle geometry without excitation. This benefit was observed over a wide range of excitation frequencies by applying very low voltages to the piezoelectric actuators.

Depuru-Mohan, N. K.↗

NASA NTRS2018

Quantified, Localized Health Benefits of Accelerated Carbon Dioxide Emissions Reductions

Societal risks increase as Earth warms, and increase further for emissions trajectories accepting relatively high levels of near-term emissions while assuming future negative emissions will compensate, even if they lead to identical warming as trajectories with reduced near-term emissions. Accelerating carbon dioxide (CO2) emissions reductions, including as a substitute for negative emissions, hence reduces long-term risks but requires dramatic near-term societal transformations. A major barrier to emissions reductions is the difficulty of reconciling immediate, localized costs with global, long-term benefits. However, 2 C trajectories not relying on negative emissions or 1.5 C trajectories require elimination of most fossil-fuel-related emissions. This generally reduces co-emissions that cause ambient air pollution, resulting in near-term, localized health benefits. We therefore examine the human health benefits of increasing 21st-century CO2 reductions by 180 GtC, an amount that would shift a 'standard' 2 C scenario to 1.5 C or could achieve 2 C without negative emissions. The decreased air pollution leads to 153 +/- 43 million fewer premature deaths worldwide, with approx.40% occurring during the next 40 years, and minimal climate disbenefits. More than a million premature deaths would be prevented in many metropolitan areas in Asia and Africa, and greater than 200,000 in individual urban areas on every inhabited continent except Australia.

Atmospheric science↗

NASA NTRS2018

Reduction in 317-780 nm Radiance Reflected from the Sunlit Earth During the Eclipse of 21 August 2017

Ten wavelength channels of calibrated radiance image data from the sunlit Earth are obtained every 65 min during Northern Hemisphere summer from the EPIC (Earth Polychromatic Imaging Camera) instrument on the DSCOVR (Deep Space Climate Observatory) satellite located near the Earth-Sun Lagrange 1 point (L1), about 1.5 million km from the Earth. The L1 location permitted seven observations of the Moon's shadow on the Earth for about 3 h during the 21 August 2017 eclipse. Two of the observations were timed to coincide with totality over Casper, Wyoming, and Columbia, Missouri. Since the solar irradiances within five channels (λi = 388, 443, 551, 680, and 780 nm) are not strongly absorbed in the atmosphere, they can be used for characterizing the eclipse reduction in reflected radiances for the Earth's sunlit face containing the eclipse shadow. Five channels (λi = 317:5, 325, 340, 688, and 764 nm) that are partially absorbed in the atmosphere give consistent reductions compared to the non-absorbed channels. This indicates that cloud reflectivities dominate the 317.5-780 nm radiances reflected back to space from the sunlit Earth's disk with a significant contribution from Rayleigh scattering for the shorter wavelengths. An estimated reduction of 10% was obtained for spectrally integrated radiance (387 to 781 nm) reflected from the sunlit Earth towards L1 for two sets of observations on 21 August 2017, while the shadow was in the vicinity of Casper, Wyoming (42.8666° N, 106.3131° W; centered on 17:44:50 UTC), and Columbia, Missouri (38.9517° N, 92.3341° W; centered on 18:14:50 UTC). In contrast, when non-eclipse days (20 and 23 August) are compared for each wavelength channel, the change in reflected light is much smaller (less than 1% for 443 nm compared to 9% (Casper) and 8% (Columbia) during the eclipse). Also measured was the ratio R(sub EN)(λi) of reflected radiance on adjacent non-eclipse days divided by radiances centered in the eclipse totality region with the same geometry for all 10 wavelength channels. The measured R(sub EN)(443 nm) was smaller for Columbia (169) than for Casper (935), because Columbia had more cloud cover than Casper. R(sub EN)(λi) forms a useful test of a 3-D radiative transfer models for an eclipse in the presence of optically thin clouds. Specific values measured at Casper with thin clouds are R(sub EN)(340 nm)=475, R(sub EN)(388 nm)=3500, REN(443 nm)=935, REN(551 nm)=5455, REN(680 nm)=220, and R(sub EN)(780 nm)=395. Some of the variability is caused by changing cloud amounts within the moving region of totality during the 2.7 min needed to measure all 10 wavelength channels.

DSCOVR↗

NASA NTRS2018

The Recent Large Reduction in Space Launch Cost

The development of commercial launch systems has substantially reduced the cost of space launch. NASA’s space shuttle had a cost of about $1.5 billion to launch 27,500 kg to Low Earth Orbit (LEO), $54,500/kg. SpaceX’s Falcon 9 now advertises a cost of $62 million to launch 22,800 kg to LEO, $2,720/kg. Commercial launch has reduced the cost to LEO by a factor of 20. This will have a substantial impact on the space industry, military space, and NASA. Existing launch providers are reducing their costs and so are satellite developers. The military foresees an opportunity to rapidly replace compromised space assets that provided communications, weather, surveillance, and positioning. NASA supported the development of commercial space launch and NASA science anticipates lower cost missions, but human space flight planning seems unreactive. Specifically, it has been claimed that commercial spaceflight has not reduced the cost to provide cargo to the International Space Station (ISS). The key factor is that the space shuttle can provide cargo and crew to ISS while the Falcon 9 must also use the Dragon capsule, which adds cost and reduces payload. The cost of a Falcon 9 and Dragon capsule mission to ISS is about $140 million with a payload of 6,000 kg, $23,300/kg. The shuttle payload to ISS is less than to LEO, 16,050 kg, so its cost is also higher at $93,400/kg. The launch cost to ISS has been reduced by a factor of 4. Calculations that show commercial launch provides no cost reduction to ISS assume half the usually cited shuttle cost and allocate it to the actual delivered payload, about half the full capacity. In a split mission, with crew and pressurized cargo launched separately from hardware and materials, the higher Falcon 9 plus Dragon costs would apply only to a fraction of the launch mass. A 4 to 1 cost reduction saves most, 75%, of the total cost. A further reduction to 10 or 20 to 1 saves 90 or 95%, but this is only a small, 15 or 20%, portion of the original cost. The recently reduced space launch cost can be expected to substantially impact human space flight.

Jones, Harry W.↗

NASA NTRS2019

Assessment of Airframe Noise Reduction Technologies Based on EPNL from Flight Tests

The acoustic performance of various airframe noise reduction technologies – Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – was determined, individually and in combination, using the Effective Perceived Noise Level metric. These noise measurements and calculations closely follow the Federal Aviation Administration aircraft noise certification standards, specifically for the approach noise measurement point. The flyover data correspond to pole-mounted, single-microphone measurements obtained during a series of flight tests, conducted under the NASA Flight Demonstrations and Capabilities project, that evaluated flap and landing gear noise reduction technologies. To minimize contributions from the propulsion system, the aircraft was flown along the approach path with engine thrust set at ground idle. Although contamination from engine, background, and secondary airframe noise sources partially masked the true performance of the tested technologies, the resulting acoustic data clearly showed substantial noise reductions relative to baseline levels. The acoustic benefits measured by the single microphones are consistent with previously reported trends in acoustic levels obtained from phased microphone array data.

Ravetta, Patricio A.↗

NASA NTRSDate not supplied

Evaluation of Variable Facesheet Liner Configurations for Broadband Noise Reduction

This paper investigates the broadband noise reduction properties of a distributed (variable) facesheet liner. Candidate uniform samples are selected using the Wave Propagation Model and Two-Parameter Model developed at the NASA Langley Research Center. Three uniform and one distributed facesheet samples are tested in the Normal Incidence Tube (NIT) at NASA Langley. Initial results show that the distributed facesheet sample possesses broadband noise reduction properties. Acoustic impedances educed from these NIT tests are used as inputs into the Convected Helmholtz Equation (CHE) propagation code developed at NASA Langley to synthesize the acoustic pressure field in the Grazing Flow Impedance Tube (GFIT) with no flow. Three uniform, one distributed, as well as one three-zone liner, oriented in two different directions, are investigated. Preliminary results showed the distributed facesheet and three-zone liners exhibit broadband noise reduction properties.

M C Brown↗

NASA NTRSDate not supplied

Hydrogen Plasma Reduction of Silicates for Lunar Oxygen Liberation

As crewed missions to the moon become closer, the focus on in-situ resource utilization efforts has increased. Since lunar soil has abundant oxygen on the surface of the moon, work has been done to process this resource in an efficient manner. Hydrogen reduction of lunar regolith has emerged as a method of liberating oxygen that can be used for fuel and water production. Traditional reduction techniques require high temperatures and increased complexity when dealing with high amounts of silicates. Plasma can reduce silicates efficiently and thus has become of high interest for use in the lunar highlands where silicates exist in high quantities. NASA’s Kennedy Space Center is exploring the use of low temperature plasmas for the reduction of silicates. This work shows that exposing silicates to a hydrogen plasma produces water. Residual gas analysis and optical emission spectroscopy were used to measure the relative quantities of water vapor production and OH (A-X) emission for hydrogen plasma interactions with lunar highland simulant and silica. X-ray photo-electron spectroscopy and scanning electron microscopy/energy-dispersive X-ray spectroscopy were also used to observe surface modifications to the silicates that reflect the key chemical reactions that occurred. From this data, plasma has emerged as a promising solution to produce oxygen on the lunar surface. *Work supported by NASA's Science Technology Mission Directorate Center Innovation Fund.

R. P. Gott↗

NASA NTRSDate not supplied

Plasma Reduction of Regolith for Oxygen Liberation

Ryan Gott↗

NASA NTRSDate not supplied

Carbothermal Reduction Demonstration: Laser Driven Reaction in a Thermal-Vacuum Environment and Project Status

Introduction: Lunar regolith is approximately 45% oxygen by mass. The majority of the oxygen is bound in silicate minerals. The carbothermal reduction process has been proven to be effective at removing oxygen from lunar regolith simulants [1]. The Carbothermal Reduction Demonstration (CaRD) project aims to increase the Technology Readiness Level (TRL) of a combined solar concentrator and carbothermal reduction systemin order to demonstrate this technology on the lunar surface. The CaRD project is divided into two design cycles, a brass board and prototype. The status of both design cycles will be discussed, as well as concepts for how this technology can be applied to the Artemis program in the future. Brassboard Vacuum Test: For the brassboard demonstration, a 2 kW Nd-YAG laser was used to heat lunar regolith simulant within a carbothermal reactor developed by Sierra Space. The reactor was placed inside of a 15 ft thermal vacuum chamber at the Johnson Space Center. The resulting reaction products were analyzed using both a gas chromotograph and mass spectrometer provided by Kennedy Space Center. Thermal data was also collected. Prototype Design: For the prototype, the CaRD team will perform another thermal vacuum test at JSC using the same interfaces and assets developed for the brassboard but will test a new carbothermal reactor design that Sierra Space is developing through the Carbothermal Oxygen Production Reactor (COPR) Tipping Point project that will include a means to autonomously move regolith in and out of the reactor. In addition, a deployable solar concentrator is being developed by Glenn Research Center using mirrors produced by Carbon Mirror Applications. The solar concentrator will be used to deliver solar energy into a carbothermal reactor to melt regolith and extract oxygen. Avionics and software for the concentrator are being developed by Kennedy Space Center. Future Concepts: An ongoing task within the CaRD project is to update models that can be used to determine the mass, power, and size of In-Situ Resource Utilization concepts at various scales. These models can now be used to analyze alternatives for future applications based on the latest available data.

A J Paz↗

NASA NTRSDate not supplied

Carbothermal Reduction Demonstration (CaRD)

Introduction: Lunar regolith is approximately 45% oxygen by mass. The majority of the oxygen is bound in silicate minerals. The carbothermal reduction process has been proven to be effective at removing oxygen from lunar regolith simulants. The Carbothermal Reduction Demonstration (CaRD) project aims to increase the Technology Readiness Level (TRL) of a combined solar concentrator and carbothermal reduction systemin order to demonstrate this technology on the lunar surface. The CaRD project is divided into two design cycles, a brass board and prototype. The status of both design cycles will be discussed, as well as concepts for how this technology can be applied to the Artemis program in the future. Brassboard Vacuum Test: For the brassboard demonstration, a 2 kW Nd-YAG laser was used to heat lunar regolith simulant within a carbothermal reactor developed by Sierra Space. The reactor was placed inside of a 15 ft thermal vacuum chamber at the Johnson Space Center. The resulting reaction products were analyzed using both a gas chromotograph and mass spectrometer provided by Kennedy Space Center. Thermal data was also collected. Prototype Design: For the prototype, the CaRD team will perform another thermal vacuum test at JSC using the same interfaces and assets developed for the brassboard but will test a new carbothermal reactor design that Sierra Space is developing through the Carbothermal Oxygen Production Reactor (COPR) Tipping Point project that will include a means to autonomously move regolith in and out of the reactor. In addition, a deployable solar concentrator is being developed by Glenn Research Center using mirrors produced by Carbon Mirror Applications. The solar concentrator will be used to deliver solar energy into a carbothermal reactor to melt regolith and extract oxygen. Avionics and software for the concentrator are being developed by Kennedy Space Center. Future Concepts: An ongoing task within the CaRD project is to update models that can be used to determine the mass, power, and size of In-Situ Resource Utilization concepts at various scales. These models can now be used to analyze alternatives for future applications based on the latest available data.

Aaron Paz↗

NASA NTRSDate not supplied

Development of Slat-gap and Slat-cove Filler Treatments for Noise Reduction Assessment on the High Lift Common Research Model in the NASA LaRC 14x22

Airframe noise is an important issue during the approach and landing phases of flight because engines are throttled back, and airframe sources become an equal or greater contributor to environmental noise. The leading-edge slat component of the high-lift system for transport aircraft has been identified as a prominent source of airframe noise. Noise production mechanisms and potential treatments to mitigate airframe noise have been areas of active research for nearly three decades. Two promising technologies for slat noise reduction are the slat-gap filler (SGF) and slat-cove filler (SCF). Previous work was done using a 2D section of a transport class aircraft wing to demonstrate their feasibility via benchtop and computational models. A wind tunnel test campaign was recently undertaken to test the SGF and SCF technologies in a flight-like environment by installing dynamically scaled treatments on the 10%-scale High-Lift Common Research Model (CRM-HL), which is representative of a commercial twin-aisle transport aircraft. Advancement of the SGF and SCF technologies to overcome challenges of integration with 3D airframe structures, computational simulations of the CRM-HL predicting the aerodynamic and aeroacoustic performance and structural loads, and design of wind tunnel model hardware with features accommodating noise treatments were conducted in parallel. Details of innovations in the SGF and SCF technologies for 3D airframe feasibility will be described. The loads the treatments must sustain in flight and the influence of those loads on the design is also discussed. Finally, the design of wing leading-edge assemblies to treat the 10% CRM-HL with dynamically scaled SGF and SCF components is presented. The treatments were successfully tested in 2020/2021 providing a demonstration of leading-edge noise reduction using components that would allow slat articulation.

airframe noise reduction↗