Search NASA⌕ Search

SEARCH · Search NASA

Results for “SANDSTONES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Final Research Performance Report - Small Molecular Associative Carbon Dioxide (CO 2 ) Thickeners for Improved Mobility Control

The initial objective of this project was to promote the application of a CO 2 thickener for improved mobility control during CO 2 EOR based on solubility tests, viscosity tests, and core floods. Ultimately, it was demonstrated that the CO 2 -soluble polymeric thickeners are much better suited for use a CO 2 -soluble conformance control agents for diverting the flow of CO 2 away from thief zones. Our team generated several effective small molecule CO 2 thickeners with ARPA-e funding. Unfortunately, none of these small molecule thickeners could dissolve in CO 2 without the addition of unacceptably large amounts of hexane or toluene as a co-solvent Therefore none were viable candidates for the core flooding studies associated with NETL award. Therefore during the entire core flood testing program associated with this NETL award, our team used only the most promising polymeric CO 2 thickener, a polyfluoroacrylate (PFA). In order to produce an environmentally benign polymer, the monomer used to make the new polymers used in this study was a fluoroacrylate that contains only six fluorinated carbons. We verified CO 2 solubility with a phase behavior cell. The thickening potential of all polymer samples was substantiated with a falling ball viscometer and a falling cylinder viscometer at Pitt. Two different viscometers were used to determine the increase in CO 2 viscosity that could be achieved via the dissolution of PFA. Praxair, which has an interest in thickening CO 2 for pilot EOR projects and for waterless hydraulic fracturing, agreed to measure the viscosity of CO 2 -PFA solutions at no cost to the project. Falling cylinder viscometery was conducted at Pitt in our windowed high pressure phase behavior cell. Both apparatuses indicated that at very low shear rates the CO 2 viscosity increased by a factor of roughly 3.5 when 1wt% PFA was dissolved in the CO 2 2. Our team also planned thickener concentrations and compositions at Pitt for the core tests that were conducted at Special Core Analysis Laboratories, Inc., (SCAL) in Midland, TX, where the ability for PFA to reduce CO 2 mobility in a core was then tested. During the beginning of these tests, the PFA polymer was then shown to impart reasonable improvements in mobility control during the SCAL core tests; as the CO 2 -PFA solution displaced CO 2 from the core at a constant volumetric flow rate, the pressure drop increased as expected. However, as the test progressed, there was clear and surprising evidence of dramatic reductions in core permeability due to PFA adsorption, especially for sandstones. For example, as the CO 2 -PFA solution displaced pure CO 2 from sandstone and limestone cores, the pressure drop increased by factors of multiple hundreds to over a thousand. It was subsequently demonstrated that the PFA injected into the core either (a) adsorbed strongly and irreversibly onto the rock surfaces, (b) deposited/precipitated within the rock, thereby blocking pores in a manner that could be dislodged by large changes in flow rate or flow direction, or (c) remained in solution and passed completely through the core. The loss of PFA to the porous media and the unacceptably large increases in pressure drop both indicated that PFA was inappropriate for CO 2 EOR mobility control, where thickener adsorption must be minimized and mobility reductions of only 10-100-fold are typically required. However, we realized that because the CO 2 -PFA solution could greatly reduce the permeability of porous media, it could serve as a near wellbore conformance control agent for blocking “thief zones”, where adsorption is acceptable and dramatic increases in pressure drop are desirable. These effects were more dramatic for sandstone than for limestone. Therefore, these PFA fluoroacrylate polymers can serve as a CO 2 -soluble conformance control agent for CO 2 -EOR, especially in sandstone formations. This injection of a single phase solution of CO 2 -PFA for permeability reduction is (to the best of our knowledge) the first report of a CO 2 -soluble conformance control additive. We also demonstrated that the optimal strategy for using CO 2 -PFA solutions for conformance control is analogous to the application of water-based polymeric gels; the CO 2 -PFA solution should first be injected only in an isolated thief zone to induce dramatic reductions in permeability only in that thief zone, and then CO 2 should be injected into all of the zones. Finally, it was noted that given the propensity of PFA to adsorb onto sandstone, the adsorption of PFA from CO 2 -PFA solutions onto cement surfaces promote the sealing of extremely fine cracks in casing cement.

02 PETROLEUM↗
DOE OSTI2018

Integrated characterization of CO 2 storage reservoirs on the Rock Springs Uplift combining geomechanics, geochemistry, and flow modeling

This project improves understanding of the effects CO 2 injection and storage on geomechanical, petrophysical, and other properties on two potential reservoirs, the Madison Limestone and Weber Sandstone, at the Rock Springs Uplift, southwest Wyoming. Rock physics studies, laboratory experiments, and computer simulations were employed. Two groups of rock samples were prepared, one aged with formation brine and the second aged with CO 2 -saturated formation brine and subsequently used for geomechanical, geochemical, and petrophysical testing. Rock physics studies provided a facies classification to discriminate among different lithologies and to investigate the feasibility of predicting petrophysical properties using seismic inversion. By applying a zone-wise regression relation established in this facies analysis, a 3D reservoir model was developed. It was determined that time-lapse seismic data are not feasible for monitoring CO 2 displacement at the Rock Springs Uplift or to mitigate leakage-risks situations because pressure and fluid saturation have small effects on elastic velocities and synthetic seismograms. The small variations that do occur are due to the low porosity of the sandstone and the high stiffness of the dolomite. In the Madison Limestone, mineral dissolution due to reaction with CO 2 -saturated brine was observed in highly permeable pathways while mineral precipitation happened in intergranular or micropores. Changes in pore size were quantified via Time-Domain Nuclear Magnetic Resonance transverse relaxation time (T 2 ) and diffusion coefficient distributions. As opposed to continuous injection of CO 2 -saturated brine, a subtle increase in porosity after static ‘soaking’ with CO 2 -saturated brine increases permeability due to the heterogeneity of changes in pore and pore throat sizes. Porosity-permeability relationships are fitted using a power-law function that can be adopted to model time-evolved porosity and permeability in a transport-limited CO 2 injection process. The effect of CO 2 -saturated brine on the linear elastic properties of Weber Sandstone and Madison Limestone cannot be generally concluded. Considering horizontal and vertical orientations and different confining pressures, no consistent relationship between stress (or strain) data and reaction with CO 2 -saturated brine was observed in the nonlinear plastic and post-failure regime. The change of elastic constants due to reaction with CO 2 -saturated brine is more significant in Madison Limestone than in Weber Sandstone; however, no consistent trend was observed. Reservoir simulations suggest that injectivity for Weber Sandstone is adversely impacted by low permeability. Changes in confining pressure do not impact injection rate and can be ignored while the effect of changes to pore pressure cannot. The effect of confining pressure and pore pressure on the size of the CO 2 plume in the Madison Limestone is negligible because of higher permeability. Geomechanical and petrophysical properties induced by CO 2 -brine-rock reactions were time-dependent. Simulations considered these time-dependent properties and indicate that injectivity, porosity distribution, pressure distribution and CO 2 saturation were affected.

58 GEOSCIENCES↗
DOE OSTI2025

Petrographic and Advanced Geologic Characterization Report on One Earth Energy #1 (API# 1211325373)

The One Earth Energy #1 (OEE1, API 1211325373) well was drilled to a depth of 7,099 feet from the Pennsylvanian bedrock to the Precambrian granite. In total, 99 thin sections were taken from Rotary Sidewall Core (RSWC) from 2,275 feet to 6,903 feet; 59 thin sections were taken from Whole Core (WC) from 4,311.5 to 6,519.2 feet for this report. This report details specifically thin section point-counting analysis that includes mineralogical and pore space analysis, including grain size analysis annotated thin section photomicrographs, scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), and statistics of grain size analysis on Mount Simon thin sections from OEE1. Characterized units include the St. Peter Sandstone, Eminence Formation, Potosi Dolomite, Franconia Formation, Davis Member, Ironton Sandstone, Galesville Sandstone, Eau Claire Formation, Elmhurst Sandstone, Mt. Simon Sandstone, and Argenta Formation.

09 BIOMASS FUELS↗
DOE OSTI2014

Geologic characterization and carbon storage resource estimates for the knox group, Illinois Basin, Illinois, Indiana and Kentucky

Research documented in this report includes (1) refinement and standardization of regional stratigraphy across the 3-state study area in Illinois, Indiana, and Kentucky, (2) detailed core description and sedimentological interpretion of Knox cores from five wells in western Kentucky, and (3) a detailed calculation of carbon storage volumetrics for the Knox using three different methodologies. Seven regional cross sections document Knox formation distribution and thickness. Uniform stratigraphic nomenclature for all three states helps to resolve state-to-state differences that previously made it difficult to evaluate the Knox on a basin-wide scale. Correlations have also refined the interpretation of an important sandstone reservoir interval in southern Indiana and western Kentucky. This sandstone, a CO2 injection zone in the KGS 1 Blan well, is correlated with the New Richmond Sandstone of Illinois. This sandstone is over 350 ft (107 m) thick in parts of southern Indiana. It has excellent porosity and permeability at sufficient depths, and provides an additional sequestration target in the Knox. The New Richmond sandstone interval has higher predictability than vuggy and fractured carbonates, and will be easier to model and monitor CO2 movement after injection.

58 GEOSCIENCES↗
DOE OSTI2014

GEOCHEMICAL INVESTIGATIONS OF CO₂-BRINE-ROCK INTERACTIONS OF THE KNOX GROUP IN THE ILLINOIS BASIN

Increased output of greenhouse gases, particularly carbon dioxide (CO₂), into the atmosphere from anthropogenic sources is of great concern. A potential technology to reduce CO₂ emissions is geologic carbon sequestration. This technology is currently being evaluated in the United States and throughout the world. The geology of the Illinois Basin exhibits outstanding potential as a carbon sequestration target, as demonstrated by the ongoing Illinois Basin – Decatur Project that is using the Mt. Simon Sandstone reservoir and Eau Claire Shale seal system to store and contain 1 million tonnes of CO₂. The Knox Group-Maquoketa Shale reservoir and seal system, located stratigraphically above the Mt. Simon Sandstone-Eau Claire Shale reservoir and seal system, has little economic value as a resource for fossil fuels or as a potable water source, making it ideal as a potential carbon sequestration target. In order for a reservoir-seal system to be effective, it must be able to contain the injected CO₂ without the potential for the release of harmful contaminants liberated by the reaction between CO₂-formation fluids and reservoir and seal rocks. This study examines portions of the Knox Group (Potosi Dolomite, Gunter Sandstone, New Richmond Sandstone) and St. Peter Sandstone, and Maquoketa Shale from various locations around the Illinois Basin. A total of 14 rock and fluid samples were exposed to simulated sequestration conditions (9101–9860 kPa [1320–1430 psi] and 32°–42°C [90°– 108°F]) for varying amounts of time (6 hours to 4 months). Knox Group reservoir rocks exhibited dissolution of dolomite in the presence of CO₂ as indicated by petrographic examination, X-ray diffraction analysis, and fluid chemistry analysis. These reactions equilibrated rapidly, and geochemical modeling confirmed that these reactions reached equilibrium within the time frames of the experiments. Pre-reaction sample mineralogy and postreaction fluid geochemistry from this study suggests only limited potential for the release of United States Environmental Protection Agency regulated inorganic contaminants into potable water sources. Short-term core flood experiments further verify that the carbonate reactions occurring in Knox Group reservoir samples reach equilibrium rapidly. The core flood experiments also lend insight to pressure changes that may occur during CO₂ injection. The Maquoketa Shale experiments reveal that this rock is initially chemically reactive when in contact with CO₂ and brine. However, due to the conservative nature of silicate and clay reaction kinetics and the rapid equilibration of carbonate reactions that occur in the shale, these reactions would not present a significant risk to the competency of the shale as an effective seal rock.

Yoksoulian, Lois↗
DOE OSTI2016

Petrochemical and Tectonogenesis of Granitoids in the Wuyo-Gubrunde Horst, Northeastern Nigeria: Implication for Uranium Enrichment

The Wuyo-Gubrunde Horst in the northeastern Nigeria consists of migmatite gneiss, unaltered, altered, and sheared porphyritic granites, pegmatites, aplites, basalts, and sandstone. Uranium has been reported in rhyolite, sheared rocks, and sandstone within the area. The petrogenesis of the granitoids and associated rocks in the area was evaluated in the light of new geochemical data, which showed that the U content of altered porphyritic granite is highest and hydrothermal-related. The granitoids are metaluminous, sub-alkaline, and S-type granite, and have evolved by partial melting of crustal material emplaced at moderate depth of 20–30 km in a syn-to late-collisional within-plate tectonic setting. The negative Eu/Eu* anomaly and high (La/Yb){sub N} ratio of the granitoids indicate magma fractionation. The low SiO{sub 2} (<53%) and high Fe{sub 2}O{sub 3} (10%) of the altered porphyritic granite compared to other similar rock units suggest pervasive alteration. The associated basalts are tholeiitic, emplaced within continental plate tectonic setting, and enriched in Ni, V, Nb, Sr, and light rare earth elements, and they have SiO{sub 2}, Fe{sub 2}O{sub 3}, V, Th, and Co contents that are similar to those of the altered porphyritic granites. The U occurrence in the Wuyo-Gubrunde Horst is believed to be sourced from the adjoining Bima sandstone in the Benue Trough, which locally contains carbonaceous zones with anomalously high concentrations of U. The Fe{sup 2+}/Fe{sup 3+} redox fronts formed by alteration of the iron-rich basalts provided the requisite geochemical barrier for U-bearing hydrothermal fluid, causing enrichment of U leached and mobilized from the sandstone through fractures in the rocks.

58 GEOSCIENCES↗
DOE OSTI2017

Final Report

This project employed a continuum approach to formulate an elastic constitutive model for Castlegate sandstone. The resulting constitutive framework for high porosity sandstone is thermodynamically sound, (i.e., does not violate the 1st and 2nd law of thermodynamics), represents known material constitutive response, and is able to be calibrated using available mechanical response data. To authenticate the accuracy of this model, a series of validation criteria were employed, using an existing mechanical response data set for Castlegate sandstone. The resulting constitutive framework is applicable to high porosity sandstones in general, and is tractable for scientists and researchers endeavoring to solve problems of practical interest.

02 PETROLEUM↗
DOE OSTI2016

Sorption and Transport Behavior of {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc on Geological Media in Radioactive Waste Repository, South Korea - 16112

Sorption experiments and a behavior investigation for the radionuclides {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc were conducted using groundwater and solid materials (mud-stone and sandstone) sampled from the Wolsong low- and intermediate-level radioactive waste repository at Gyeongju, Korea. After experiments involving batch sorption, diffusion, and a flow-through column, distribution coefficients (K{sub d}) of the radionuclides were obtained, and sorption properties for each radionuclide were analyzed. Increasing K{sub d} values were observed in the sequence {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc regardless of the geological media tested. For all sorbing radionuclides, K{sub d} values for the mud-stone were observed to be higher than those for sandstone regardless of the groundwater. These higher K{sub d} values are the result of higher levels of total organic carbon in the mud-stone than were present in the sandstone. In addition, the chlorite, kaolinite, and montmorillonite contents in the mud-stone also were higher than in the sandstone. The mineralogical composition of the solid materials was observed to be important in the sorption of sorbing radionuclides. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

The strength anisotropy of localized compaction: A model for the role of the nature and orientation of cross‐beds on the orientation and distribution of compaction bands in 3‐D

Abstract The field observations indicate that the low‐angle bed‐parallel compaction bands and the high‐angle‐to‐bedding compaction bands occur only in cross‐beds with certain range of bedding orientations in the Aztec Sandstone at the Valley of Fire State Park (NV). The hypothesis is that the primary underlying mechanical reason for this phenomenon is the strength anisotropy of localized compaction in anisotropic sandstones. In this paper, we used a quadratic failure criterion to describe the strength anisotropy of localized compaction and compared the results with the field data. The results show a clear relationship among the cross‐beds with (or without) compaction bands of certain orientations and the cross‐beds with relatively lower (or higher) calculated strength of localized compaction. We also used the quadratic failure criterion to fit the yield caps of anisotropic sandstones deformed in the laboratory by previous investigators and achieved some degree of success. These findings indicate that the strength anisotropy of localized compaction is an important factor controlling the compartmentalized distribution of compaction bands of various orientations in the aeolian sandstones.

Deng, Shang↗
DOE OSTI2017

Pore-scale capillary pressure analysis using multi-scale X-ray micromotography

Here, a multi-scale synchrotron-based X-ray microtomographic dataset of residually trapped air after gravity-driven brine imbibition was acquired for three samples with differing pore topologies and morphologies; image volumes were reconstructed with voxel sizes from 4.44 µm down to 0.64 µm. Capillary pressure distributions among the population of trapped ganglia were investigated by calculating interfacial curvature in order to assess the potential for remobilization of residually-trapped non-wetting ganglia due to differences in capillary pressure presented by neighbor ganglia. For each sample, sintered glass beads, Boise sandstone and Fontainebleau sandstone, sub-volumes with different voxel sizes were analyzed to quantify air/brine interfaces and interfacial curvatures and investigate the effect of image resolution on both fluid phase identification and curvature estimates. Results show that the method developed for interfacial curvature estimation leads to reliable capillary pressure estimates for gas ganglia. Higher resolution images increase confidence in curvature calculations, especially for the sandstone samples that display smaller gas-brine interfaces which are then represented by a higher number of voxels when imaged with a micron or sub-micron voxels size. The analysis of sub-volumes from the Boise and Fontainebleau dataset highlights the presence of a residually-trapped gas phase consisting of ganglia located in one or few pores and presenting significantly different capillary pressures, especially in the case of Fontainebleau sandstone. As a result, Ostwald ripening could occur, leading to gas transfer from ganglia with higher capillary pressure to surrounding ganglia with lower capillary pressures. More generally, at the pore-scale, most gas ganglia do present similar capillary pressures and Ostwald ripening would then not represent a major mechanism for residually-trapped gas transfer and remobilization.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2015

Reaction and diffusion at the reservoir/shale interface during CO 2 storage: Impact of geochemical kinetics

Here we use a reactive diffusion model to investigate what happens to CO 2 injected into a subsurface sandstone reservoir capped by a chlorite- and illite-containing shale seal. The calculations simulate reaction and transport of supercritical (SC) CO 2 at 348.15 K and 30 MPa up to 20,000 a. Given the low shale porosity (5%), chemical reactions mostly occurred in the sandstone for the first 2000 a with some precipitation at the ss/sh interface. From 2000 to 4000 a, ankerite, dolomite and illite began replacing Mg–Fe chlorite at the sandstone/shale interface. Transformation of chlorite to ankerite is the dominant reaction occluding the shale porosity in most simulations: from 4000 to 7500 a, this carbonation seals the reservoir and terminates reaction. Overall, the carbonates (calcite, ankerite, dolomite), chlorite and goethite all remain close to local chemical equilibrium with brine. Quartz is almost inert from the point of its dissolution/precipitation. However, the rate of quartz reaction controls the long-term decline in aqueous silica activity and its evolution toward equilibrium. The reactions of feldspars and clays depend strongly on their reaction rate constants (microcline is closer to local equilibrium than albite). The timing of porosity occlusion mostly therefore depends on the kinetic constants of kaolinite and illite. For example, an increase in the kaolinite kinetic constant by 0.25 logarithmic units hastened porosity closure by 4300 a. The earliest simulated closure of porosity occurred at approximately 108 a for simulations designed as sensitivity tests for the rate constants. These simulations also emphasize that the rate of CO 2 immobilization as aqueous bicarbonate (solubility trapping) or as carbonate minerals (mineral trapping) in sandstone reservoirs depends upon reaction kinetics – but the relative fraction of each trapped CO 2 species only depends upon the initial chemical composition of the host sandstone. For example, at the point of porosity occlusion the fraction of bicarbonate remaining in solution depends upon the initial Na and K content in the host rock but the fraction of carbonate mineralization depends only on the Ca, Mg, Fe content. Since ankerite is the dominant mineral that occludes porosity, the dissolved concentration of ferrous iron is also an important parameter. Finally, future efforts should focus on cross-comparisons and ground-truthing of simulations made for standard case studies as well as laboratory measurements of the reactivities of clay minerals.

58 GEOSCIENCES↗
DOE OSTI2014

Design Support of an Above Cap-rock Early Detection Monitoring System using Simulated Leakage Scenarios at the FutureGen2.0 Site

The FutureGen 2.0 Project will design and build a first-of-its-kind, near-zero emissions coal-fueled power plant with carbon capture and storage (CCS). To assess storage site performance and meet the regulatory requirements of the Class VI Underground Injection Control (UIC) Program for CO 2 Geologic Sequestration, the FutureGen 2.0 project will implement a suite of monitoring technologies designed to evaluate CO 2 mass balance and detect any unforeseen loss in CO 2 containment. The monitoring program will include direct monitoring of the reservoir, and early-leak-detection monitoring directly above the primary confining zone. This preliminary modeling study described here focuses on hypothetical leakage scenarios into the first permeable unit above the primary confining zone (Ironton Sandstone) and is used to support assessment of early-leak detection capabilities. Future updates of the model will be used to assess potential impacts on the lowermost underground source of drinking water (Saint Peter Sandstone) for a range of theoretical leakage scenarios. This preliminary modeling evaluation considers both pressure response and geochemical signals in the overlying Ironton Sandstone. This model is independent of the FutureGen 2.0 reservoir model in that it does not simulate caprock discontinuities, faults, or failure scenarios. Instead this modeling effort is based on theoretical, volumetric-rate based leakage scenarios. The scenarios include leakage of 1% of the total injected CO 2 mass, but spread out over different time periods (20, 100, and 500 years) with each case yielding a different mass flux (i.e., smaller mass fluxes for longer duration leakage cases]. A brine leakage scenario using a volumetric leakage similar to the 20 year 1% CO 2 case was also considered. A framework for the comparison of the various cases was developed based on the exceedance of selected pressure and geochemical thresholds at different distances from the point of leakage and at different vertical positions within the Ironton Sandstone. These preliminary results, and results from an updated models that incorporate additional site-specific characterization data, support development/refinement of the monitoring system design.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2013

Trace Metal Source Terms in Carbon Sequestration Environments

ABSTRACT: Carbon dioxide sequestration in deep saline and depleted oil geologic formations is feasible and promising; however, possible CO2 or CO2-saturated brine leakage to overlying aquifers may pose environmental and health impacts. The purpose of this study was to experimentally define to provide a range of concentrations that can be used as the trace element source term for reservoirs and leakage pathways in risk simulations. Storage source terms for trace metals are needed to evaluate the impact of brines leaking into overlying drinking water aquifers. The trace metal release was measured from cements and sandstones, shales, carbonates, evaporites, and basalts from the Frio, In Salah, Illinois Basin, Decatur, Lower Tuscaloosa, Weyburn-Midale, Bass Islands, and Grand Ronde carbon sequestration geologic formations. Trace metal dissolution was tracked by measuring solution concentrations over time under conditions (e.g., pressures, temperatures, and initial brine compositions) specific to the sequestration projects. Existing metrics for maximum contaminant levels (MCLs) for drinking water as defined by the U.S. Environmental Protection Agency (U.S. EPA) were used to categorize the relative significance of metal concentration changes in storage environments because of the presence of CO2. Results indicate that Cr and Pb released from sandstone reservoir and shale cap rocks exceed the MCLs byan order of magnitude, while Cd and Cu were at or below drinking water thresholds. In carbonate reservoirs As exceeds the MCLs by an order of magnitude, while Cd, Cu, and Pb were at or below drinking water standards. Results from this study can be used as a reasonable estimate of the trace element source term for reservoirs and leakage pathways in risk simulations to further evaluate the impact of leakage on groundwater quality.

Trace Metal Source Terms in↗
DOE OSTI2017

Permeability and Mineral Composition Evolution of Primary Seal and Reservoir Rocks in Geologic Carbon Storage Conditions

It has been reported that deep saline aquifers represent the largest geologic CO 2 storage resource. To better predict containment effectiveness and long-term reservoir behavior of these formations, it is important to understand the potential geochemically induced changes to the porosity and permeability of both the primary sealing formation and CO 2 storage formation rocks. To investigate these potential changes, an experimental study to probe the geochemical interactions of CO 2 /brine/rock system under geologic CO 2 storage conditions was conducted in a static reaction system. Marine shale (primary sealing formation) and Lower Tuscaloosa sandstone (CO 2 storage formation) core samples taken from the Plant Daniel CO 2 storage test site (Jackson County, Mississippi) were exposed to CO 2 -saturated brine in a batch reactor at relevant geologic storage conditions (85°C and 23.8 MPa CO 2 pressure) for 6 months. X-ray diffraction, scanning electron microscopy, computed tomography, and brine chemistry analyses were performed before and after the exposure. Permeability measurements from the marine shale and sandstone core samples before and after CO 2 /brine exposure indicated a significant effective permeability change. Sealing marine shale permeability increased following exposure while the permeability of the sandstone from the storage formation was observed to decrease. Analysis results of the primary sealing formation sample (marine shale) at the Plant Daniel CO 2 storage test site have not been reported before. In conclusion, the permeability decrease of the Lower Tuscaloosa sandstone sample reported in this study verifies the results reported in a previous study. These results have implications for the integrity of the primary seal in a CO 2 storage setting.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2016

Quartz c-axis orientation patterns in fracture cement as a measure of fracture opening rate and a validation tool for fracture pattern models

Here, we evaluate a published model for crystal growth patterns in quartz cement in sandstone fractures by comparing crystal fracture-spanning predictions to quartz c-axis orientation distributions measured by electron backscatter diffraction (EBSD) of spanning quartz deposits. Samples from eight subvertical opening-mode fractures in four sandstone formations, the Jurassic– Cretaceous Nikanassin Formation, northwestern Alberta Foothills (Canada), Cretaceous Mesaverde Group (USA; Cozzette Sandstone Member of the Iles Formation), Piceance Basin, Colorado (USA), and upper Jurassic–lower Cretaceous Cotton Valley Group (Taylor sandstone) and overlying Travis Peak Formation, east Texas, have similar quartzose composition and grain size but contain fractures with different temperature histories and opening rates based on fluid inclusion assemblages and burial history. Spherical statistical analysis shows that, in agreement with model predictions, bridging crystals have a preferred orientation with c-axis orientations at a high angle to fracture walls. The second form of validation is for spanning potential that depends on the size of cut substrate grains. Using measured cut substrate grain sizes and c-axis orientations of spanning bridges, we calculated the required orientation for the smallest cut grain to span the maximum gap size and the required orientation of the crystal with the least spanning potential to form overgrowths that span across maximum measured gap sizes. We find that within a 10° error all spanning crystals conform to model predictions. Using crystals with the lowest spanning potential based on crystallographic orientation (c-axis parallel to fracture wall) and a temperature range for fracture opening measured from fluid inclusion assemblages, we calculate maximum fracture opening rates that allow crystals to span. These rates are comparable to those derived independently from fracture temperature histories based on burial history and multiple sequential fluid inclusion assemblages. Results support the R. Lander and S. Laubach model, which predicts that for quartz deposited synchronously with fracture opening, spanning potential, or likelihood of quartz deposits that are thick enough to span between fracture walls, depends on temperature history, fracture opening rate, size of opening increments, and size, mineralogy, and crystallographic orientation of substrates in the fracture wall (transected grains). Results suggest that EBSD maps, which can be more rapidly acquired than measurement of tens to hundreds of fluid inclusion assemblages, can provide a useful measure of relative opening rates within populations of quartz-filled fractures formed under sedimentary basin conditions. Such data are useful for evaluating fracture pattern development models.

36 MATERIALS SCIENCE↗
DOE OSTI2012

An Assessment of Geological Carbon Storage Options in the Illinois Basin: Validation Phase

The Midwest Geological Sequestration Consortium (MGSC) assessed the options for geological carbon dioxide (CO 2 ) storage in the 155,400 km 2 (60,000 mi 2 ) Illinois Basin, which underlies most of Illinois, western Indiana, and western Kentucky. The region has annual CO 2 emissions of about 265 million metric tonnes (292 million tons), primarily from 122 coal-fired electric generation facilities, some of which burn almost 4.5 million tonnes (5 million tons) of coal per year (U.S. Department of Energy, 2010). Validation Phase (Phase II) field tests gathered pilot data to update the Characterization Phase (Phase I) assessment of options for capture, transportation, and storage of CO 2 emissions in three geological sink types: coal seams, oil fields, and saline reservoirs. Four small-scale field tests were conducted to determine the properties of rock units that control injectivity of CO 2 , assess the total storage resources, examine the security of the overlying rock units that act as seals for the reservoirs, and develop ways to control and measure the safety of injection and storage processes. The MGSC designed field test operational plans for pilot sites based on the site screening process, MVA program needs, the selection of equipment related to CO 2 injection, and design of a data acquisition system. Reservoir modeling, computational simulations, and statistical methods assessed and interpreted data gathered from the field tests. Monitoring, Verification, and Accounting (MVA) programs were established to detect leakage of injected CO 2 and ensure public safety. Public outreach and education remained an important part of the project; meetings and presentations informed public and private regional stakeholders of the results and findings. A miscible (liquid) CO 2 flood pilot project was conducted in the Clore Formation sandstone (Mississippian System, Chesterian Series) at Mumford Hills Field in Posey County, southwestern Indiana, and an immiscible CO 2 flood pilot was conducted in the Jackson sandstone (Mississippian System Big Clifty Sandstone Member) at the Sugar Creek Field in Hopkins County, western Kentucky. Up to 12% incremental oil recovery was estimated based on these pilots. A CO 2 huff puff (HNP) pilot project was conducted in the Cypress Sandstone in the Loudon Field. This pilot was designed to measure and record data that could be used to calibrate a reservoir simulation model. A pilot project at the Tanquary Farms site in Wabash County, southeastern Illinois, tested the potential storage of CO 2 in the Springfield Coal Member of the Carbondale Formation (Pennsylvanian System), in order to gauge the potential for large-scale CO 2 storage and/or enhanced coal bed methane recovery from Illinois Basin coal beds. The pilot results from all four sites showed that CO 2 could be injected into the subsurface without adversely affecting groundwater. Additionally, hydrocarbon production was enhanced, giving further evidence that CO 2 storage in oil reservoirs and coal beds offers an economic advantage. Results from the MVA program at each site indicated that injected CO 2 did not leave the injection zone. Topical reports were completed on the Middle and Late Devonian New Albany Shale and Basin CO 2 emissions. The efficacy of the New Albany Shale as a storage sink could be substantial if low injectivity concerns can be alleviated. CO 2 emissions in the Illinois Basin were projected to be dominated by coal-fired power plants.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2013

Analysis of Potential Leakage Pathways and Mineralization within Caprocks for Geologic Storage of CO 2

We used a multifaceted approach to investigate the nature of caprocks above, and the interface between, reservoir-quality rocks that might serve as targets for carbon storage. Fieldwork in southeastern Utah examined the regional- to m-scale nature of faults and fractures across the sedimentiological interfaces. We also used microscopic analyses and mechanical modeling to examine the question as to how the contacts between units interact, and how fractures may allow fluids to move from reservoirs to caprock. Regional-­scale analyses using ASTER data enabled us to identify location of alteration, which led to site-­specific studies of deformation and fluid flow. In the Jurassic Carmel Formation, a seal for the Navajo Sandstone, we evaluated mesoscale variability in fracture density and morphology and variability in elastic moduli in the Jurassic Carmel Formation, a proposed seal to the underlying Navajo Sandstone for CO 2 geosequestration. By combining mechano-stratigraphic outcrop observations with elastic moduli derived from wireline log data, we characterize the variability in fracture pattern and morphology with the observed variability in rock strength within this heterolithic top seal. Outcrop inventories of discontinuities show fracture densities decrease as bed thickness increases and fracture propagation morphology across lithologic interfaces vary with changing interface type. Dynamic elastic moduli, calculated from wireline log data, show that Young’s modulus varies by up to 40 GPa across depositional interfaces, and by an average of 3 GPa across the reservoir/seal interface. We expect that the mesoscale changes in rock strength will affect the distributions of localized stress and thereby influence fracture propagation and fluid flow behavior within the seal. These data provide a means to closely tie outcrop observations to those derived from subsurface data and estimates of subsurface rock strength. We also studied damage zones associated normal faults in the Permian Cedar Mesa Sandstone, southeastern Utah. These faults are characterized by a single slip surfaces and damage zones containing deformation bands, veins, and joints. Field observations include crosscutting relationships, permeability increase, rock strength decrease, and ultraviolet light induced mineral fluorescence within the damage zone. These field observations combined with the interpreted paragenetic sequence from petrographic analysis, suggests a deformation history of reactivation and several mineralization events in an otherwise low-permeability fault. All deformation bands and veins fluoresce under ultraviolet light, suggesting connectivity and a shared mineralization history. Pre-­existing deformation features act as loci for younger deformation and mineralization events, this fault and its damage zone illustrate the importance of the fault damage zone to subsurface fluid flow. We model a simplified stress history in order to understand the importance of rock properties and magnitude of tectonic stress on the deformation features within the damage zone. The moderate confining pressures, possible variations in pore pressure, and the porous, fine-­grained nature of the Cedar Mesa Sandstone results in a fault damage zone characterized by enhanced permeability, subsurface fluid flow, and mineralization. Structural setting greatly influences fracture spacing and orientation. Three structural settings were examined and include fault proximity, a fold limb of constant dip, and a setting proximal to the syncline hinge. Fracture spacing and dominant fracture orientation vary at each setting and distinctions between regional and local paleo-stress directions can be made. Joints on the fold limb strike normal to the fold axis/bedding and are interpreted to be sub-parallel to the maximum regional paleo-stress direction as there is no fold related strain. Joints proximal to faults and the syncline hinge may have formed under local stress conditions associated with folding and faulting, and in some cases, are perpendicular to the maximum regional paleo-stress direction. Macroscale analyses of the Iron Wash fault, which cuts most of the stratigraphy of the reservoir- seal analogs, reveals that seal bypass occurs along faults with mixed lithologic composition. While portions of the fault may be effective seals, when modeled as a whole the fault zone cannot support a high CO 2 column. We adapted oil-field methods to calculate column heights and sealing capacities. Examination of the burial and tectonic histories of the rocks, coupled with field- and micro-­scale studies, allow us to examine the potential for seal failure using basic rock mechanics failure analyses. These studies reveal that the sealing lithologies experienced multiple episodes of deformation that resulted in numerous fractures and small faults. In a stress state based on burial history and overburden loads, we show that most of the seals could fail with normal to slightly excess pore pressures.

58 GEOSCIENCES↗
DOE OSTI2014

Area of Interest 1, CO 2 at the Interface: Nature and Dynamics of the Reservoir/Caprock Contact and Implications for Carbon Storage Performance

We examined the influence of geologic features present at the reservoir/caprock interface on the transmission of supercritical CO 2 into and through caprock. We focused on the case of deformation-band faults in reservoir lithologies that intersect the interface and transition to opening-mode fractures in caprock lithologies. Deformation-band faults are exceeding common in potential CO 2 injection units and our fieldwork in Utah indicates that this sort of transition is common. To quantify the impact of these interface features on flow and transport we first described the sedimentology and permeability characteristics of selected sites along the Navajo Sandstone (reservoir lithology) and Carmel Formation (caprock lithology) interface, and along the Slickrock Member (reservoir lithology) and Earthy Member (caprock lithology) of the Entrada Sandstone interface, and used this information to construct conceptual permeability models for numerical analysis. We then examined the impact of these structures on flow using single-phase and multiphase numerical flow models for these study sites. Key findings include: (1) Deformation-band faults strongly compartmentalize the reservoir and largely block cross-fault flow of supercritical CO 2 . (2) Significant flow of CO 2 through the fractures is possible, however, the magnitude is dependent on the small-scale geometry of the contact between the opening-mode fracture and the deformation band fault. (3) Due to the presence of permeable units in the caprock, caprock units are capable of storing significant volumes of CO 2 , particularly when the fracture network does not extend all the way through the caprock. The large-scale distribution of these deformation-bandfault-to-opening-mode-fractures is related to the curvature of the beds, with greater densities of fractures in high curvature regions. We also examined core and outcrops from the Mount Simon Sandstone and Eau Claire Formation reservoir/caprock interface in order to extend our work to a reservoir/caprock pair this is currently being assessed for long-term carbon storage. These analyses indicate that interface features similar to those observed at the Utah sites 3 were not observed. Although not directly related to our main study topic, one byproduct of our investigation is documentation of exceptionally high degrees of heterogeneity in the pore-size distribution of the Mount Simon Sandstone. This suggests that the unit has a greater-than-normal potential for residual trapping of supercritical CO 2 .

54 ENVIRONMENTAL SCIENCES↗