Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLENDER BODY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Aerodynamic Investigation of a Parabolic Body of Revolution at Mach Number of 1.92 and Some Effects of an Annular Supersonic Jet Exhausting from the Base

An aerodynamic investigation of a slender pointed parabolic body of revolution was conducted at Mach number of 1.92 with and without the effects of an annular supersonic jet exhausting from the base. Measurements with the jet inoperative were made of lift, drag, pitching moment, base pressures, and radial and axial pressures. With the jet in operation, pressure measurements were made over the rear of the body with the primary variables being angle of attack, ratio of jet velocity to stream velocity, and ratio of pressure at jet exit to stream pressure.

Love, Eugene S↗
NASA NTRS1993

Efficient Three-Dimensional Direct Simulation Monte Carlo for Complex Geometry Problems

The simulation of flowfields in the transition flow regime is notoriously difficult with high demands on computer resources (CPU time and storage) and user expertise/labor. This paper describes a new, efficient code which has been developed to simulate high Knudsen number flowfields in three dimensions about bodies of arbitrarily complex geometry. The algorithm has been tested over a wide range of conditions, from free molecular to near-continuum flow regimes, for slender and blunt bodies, for re-entry vehicles and spacecraft. A series of validation tests have been conducted using both wind-tunnel measurements and flight data.

Rault, Didier F. G.↗
NASA NTRS1957

Nonlifting wing-body combinations with certain geometric restraints having minimum wave drag at low supersonic speeds

Several variational problems involving optimum wing and body combinations having minimum wave drag for different kinds of geometrical restraints are analyzed. Particular attention is paid to the effect on the wave drag of shortening the fuselage and, for slender axially symmetric bodies, the effect of fixing the fuselage diameter at several points or even of fixing whole portions of its shape.

Lomax, Harvard↗
NASA NTRS1953

Transient temperature distributions in simple conducting bodies steadily heated through a laminar boundary layer

An analysis is made of the transient heat-conduction effects in three simple semi-infinite bodies: the flat insulated plate, the conical shell, and the slender solid cone. The bodies are assumed to have constant initial temperatures and, at zero time, to begin to move at a constant speed and zero angle of attack through a homogeneous atmosphere. The heat input is taken as that through a laminar boundary layer. Radiation heat transfer and transverse temperature gradients are assumed to be zero. The appropriate heat-conduction equations are solved by an iteration method, the zeroeth-order terms describing the situation in the limit of small time. The method is presented and the solutions are calculated to three orders which are sufficient to give reasonably accurate results when the forward edge has attained one-half the total temperature rise (nose half-rise time). Flight Mach number and air properties occur as parameters in the result. Approximate expressions for the extent of the conduction region and nose half-rise times as functions of the parameters of the problem are presented. (author)

Parker, Hermon M↗
NASA NTRS1963

Effects of Mass Addition on the Stability of Slender Cones at Hypersonic Speeds

The effect of mass addition on the flow over bodies moving at hypersonic speeds has been studied by several investigators (e.g., Cresci and Libby). In most of this work, primary attention logically has been directed toward the effects of foreign-gas injection on heat transfer and pressure distributions, and, principally for this reason, most of the work ha been done at zero angle of attack. The foreign gas can be provided either by some active injection system or by the action of an ablation heat shield. With increasing rates of injection, the basic flow about the body can be affected significantly. One such effect was observed in the paper by Cresci and Libby, where it was shown that the shockwave standoff distance can be increased by gas injection at the nose of a body.

SLENDER BODY↗
NASA NTRS1981

Unsteady Newton-Busemann flow theory. Part 2: Bodies of revolution

Newtonian flow theory for unsteady flow past oscillating bodies of revolution at very high Mach numbers is completed by adding a centrifugal force correction to the impact pressures. Exact formulas for the unsteady pressure and the stability derivatives are obtained in closed form and are applicable to bodies of revolution that have arbitrary shapes, arbitrary thicknesses, and either sharp or blunt noses. The centrifugal force correction arising from the curved trajectories followed by the fluid particles in unsteady flow cannot be neglected even for the case of a circular cone. With this correction, the present theory is in excellent agreement with experimental results for sharp cones and for cones with small nose bluntness; gives poor agreement with the results of experiments in air for bodies with moderate or large nose bluntness. The pitching motions of slender power-law bodies of revulution are shown to be always dynamically stable according to Newton-Busemann theory.

Hui, W. H.↗
NASA NTRS1975

Unsteady transonic aerodynamics - An aeronautics challenge

The paper presents a review of the historical development in unsteady transonic aerodynamics, along with the foundations and accomplishments of several approaches to solve the equations of unsteady transonic flow. The discussion covers the linearized unsteady flow theory, numerical solution of the exact equations for an inviscid compressible gas, nonlinear small disturbance theory of transonic flow and linearization of the unsteady component about the nonlinear solution for the steady state, local linearization solution for unsteady transonic flow, unsteady transonic flow theory for slender wings and bodies, and three-dimensional unsteady transonic flows. The relation between the calculated results and experiment is examined. It is shown that the newly emerging numerical methods are capable of solving the nonlinear equations for two-dimensional flow and can be extended to three-dimensional flows.

Spreiter, J. R.↗
NASA NTRS1989

Transonic Symposium: Theory, Application and Experiment, volume 2

Papers presented at the Transonic Symposium are compiled. The following subject areas are covered: National Transonic Facility status; transonic aerodynamics of slender wing-body configuration; laminar flow flight experiments; laminar flow wind tunnel experiments; computational support of X-29A flight experiment; transition location on a clean-up glove installed on a F-14 aircraft; and design studies for a laminar glove for the X-29 aircraft.

Foughner, Jerome T., Jr.↗
NASA NTRS1993

Nonequilibrium effects on the aerothermodynamics of transatmospheric and aerobraking vehicles

A 3D CFD algorithm is used to study the effect of thermal and chemical nonequilibrium on slender and blunt body aerothermodynamics. Both perfect gas and reacting gas air models are used to compute the flow over a generic transatmospheric vehicle and a proposed lunar transfer vehicle. The reacting air is characterized by a translational-rotational temperature and a vibrational-electron-electronic temperature and includes eight chemical species. The effects of chemical reaction, vibrational excitation, and ionization on lift-to-drag ratio and trim angle are investigated. Results for the NASA Ames All-body Configuration show a significant difference in center of gravity location for a reacting gas flight case when compared to a perfect gas wind tunnel case at the same Mach number, Reynolds number, and angle of attack. For the same center of gravity location, the wind tunnel model trims at lower angle of attack than the full-scale flight case. Nonionized and ionized results for a proposed lunar transfer vehicle compare well to computational results obtained from a previously validated reacting gas algorithm. Under the conditions investigated, effects of weak ionization on the heat transfer and aerodynamic coefficients were minimal.

Hassan, Basil↗
NASA NTRS2013

Long Penetration Mode Counterflowing Jets for Supersonic Slender Configurations - A Numerical Study

A novel approach of using counterflowing jets positioned strategically on the aircraft and exploiting its long penetration mode (LPM) of interaction towards sonic-boom mitigation forms the motivation for this study. Given that most previous studies on the counterflowing LPM jet have all been on blunt bodies and at high supersonic or hypersonic flow conditions, exploring the feasibility to obtain a LPM jet issuing from a slender body against low supersonic freestream conditions is the main focus of this study. Computational fluid dynamics computations of axisymmetric models (cone-cylinder and quartic geometry), of relevance to NASA's High Speed project, are carried out using the space-time conservation element solution element viscous flow solver with unstructured meshes. A systematic parametric study is conducted to determine the optimum combination of counterflowing jet size, mass flow rate, and nozzle geometry for obtaining LPM jets. Details from these computations will be used to assess the potential of the LPM counterflowing supersonic jet as a means of active flow control for enabling supersonic flight over land and to establish the knowledge base for possible future implementation of such technologies.

Venkatachari, Balaji Shankar↗
NASA NTRS1978

Wake vortex measurements of bodies at high angle of attack

Three-dimensional laser velocimeter measurements have been made of the wake vortices of a slender tangent-ogive body which had nose and body fineness ratios of 3.5 and 12, respectively. Data were obtained for an angle of attack to seminose angle ratio of 2.3 at a free-stream Mach number of 0.6 and unit Reynolds number of 2 million/ft. Details of the mean flow field are presented and features of the turbulent and unsteady nature of the vortex flow field are discussed. Problems associated with obtaining meaningful vortex measurements in high-speed flows are addressed.

Owen, F. K.↗
NASA NTRS1990

Physical considerations governing computation of turbulent flows over bodies at large incidence

The physical aspects governing accurate numerical simulation of turbulent flows having large regions of crossflow separation are re-examined. Time-accurate, three-dimensional fine-grid Navier-Stokes solutions were obtained for turbulent subsonic and supersonic flows over a slender ogive-cylinder body of revolution at large angles of attack. These flowfields are complex and contain regions of crossflow separation and an organized leeward-side vortex structure. An algebraic eddy-viscosity turbulence model has been modified to correctly account for the effects of the vortices on the underlying viscous layers. The numerical results show that the vortical flow structure of both subsonic and supersonic high incidence flows are similar, and can be accurately treated by the turbulence model. As the angle of attack is increased, the effectiveness of the model increases since the influence of the vortices on the underlying boundary layer decreases.

Degani, David↗
NASA NTRS1998

Global Artificial Boundary Conditions for Computation of External Flow Problems with Propulsive Jets

We propose new global artificial boundary conditions (ABC's) for computation of flows with propulsive jets. The algorithm is based on application of the difference potentials method (DPM). Previously, similar boundary conditions have been implemented for calculation of external compressible viscous flows around finite bodies. The proposed modification substantially extends the applicability range of the DPM-based algorithm. In the paper, we present the general formulation of the problem, describe our numerical methodology, and discuss the corresponding computational results. The particular configuration that we analyze is a slender three-dimensional body with boat-tail geometry and supersonic jet exhaust in a subsonic external flow under zero angle of attack. Similarly to the results obtained earlier for the flows around airfoils and wings, current results for the jet flow case corroborate the superiority of the DPM-based ABC's over standard local methodologies from the standpoints of accuracy, overall numerical performance, and robustness.

Tsynkov, Semyon↗
NASA NTRS1992

The numerical study of 3-D flow past control surfaces

The computation of a steady 3D viscous flow past a slender delta wing-body configuration with trailing edge control surfaces is presented. For the numerical simulation, a cell centered finite volume Navier-Stokes zonal method was used and, besides the standard nonplanar zonal interfacing techniques, a new zonal capability, called a 'virtual zone', was implemented. This capability enables the end caps of the wings or flaps to be gridded and interfaced with the rest of the flowfield in a natural and straightforward manner. The computational results for 0-, 10-, and 24-deg angles-of-attack were found to agree with experimental results qualitively and quantitatively.

Chaussee, Denny S.↗
NASA NTRS1993

A numerical study of the effect of geometry variation, turbulence models, and dissipation on the flow past control surfaces

The steady 3D viscous flow past the ONERA M6 wing and a slender delta wing-body with trailing edge control surfaces has been computed. A cell-centered finite-volume Navier-Stokes patched zonal method has been used for the numerical simulation. Both diagonalized and LUSGS schemes have been implemented. Besides the standard nonplanar zonal interfacing techniques, a new virtual zone capability has been employed. For code validation, the transonic flow past the ONERA M5 wing is calculated for angles-of-attack of 3.06 deg and 5.06 deg and compared with the available experiments. The wing-body computational results are compared with experimental data for both trailing-edge flaps deflected. The experimental flow conditions are M subinfinity = 0.4, a turbulent Reynolds number of 5.41 million based on a mean aerodynamic chord of 25.959 inches, adiabatic wall, and angles-of-attack varying from 0 deg to 23.85 deg. The computational results are presented for the 23.85 deg angle-of-attack case. The effects of the base flow due to a model sting, the varying second and fourth order numerical dissipation, and the turbulence model are all considered.

Chaussee, Denny S.↗
NASA NTRSDate not supplied

The AEDC 10-Deg Cone Wind Tunnel/Flight Laminar-Turbulent Correlation Program

The AEDC 10-Deg Cone Program stands as a historical tunnel/flight correlation program in which a simple standard calibration body (a sharp, smooth, slender 10-deg included-angle cone) was used for correlation of wind tunnel flow quality and Reynolds number effects in 23 major wind tunnels. The investigation, initiated by the USAF at AEDC, was conducted in the 1970’s and included participation by NASA, the Navy, the United Kingdom, France, the Netherlands, and Industry. The flight test was performed at NASA/DFRC (now AFRC) at Edwards AFB on a NASA F-15 A aircraft to Mach 2.0. Testing in the wind tunnels was from Mach 0.2 to 5.5. This program produced an extensive database.

AEDC 10-Deg Cone↗