SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Clay slurries are both ubiquitous and essential in the oil exploration industry, and are most commonly employed as drilling fluids.
Lignocellulolytic enzymes remain one of the primary cost constraints in second-generation (2G) ethanol biorefineries. Achieving efficient hydrolysis of structural carbohydrates with minimal enzyme dosage, maintaining slurry fermentability for industrially relevant ethanol titers, and maximizing ethanol yield per ton of biomass are among the major challenges in 2G processes. In this study, we optimized the dosages of pre-commercial cellulase (NS22257) and hemicellulase (NS22244) on pilot-scale, hydrothermally pretreated lignocellulosic substrates. Enzyme dosages were evaluated at three levels: 20 mg of cellulase with 7.25 mg of hemicellulase (ED-1), 40 mg with 14.5 mg (ED-2), and 60 mg with 21.75 mg (ED-3). As expected, the highest sugar yields were obtained with ED-3; however, for sweet sorghum, oilcane, and miscanthus, sugar yields from ED-2 and ED-3 were not significantly different ( p < 0.05). For example, sweet sorghum produced 123.78 ± 1.54 g L −1 and 125.76 ± 0.46 g L −1 of total sugars (glucose and xylose) with ED-2 and ED-3, respectively. Although energycane exhibited a statistically significant difference between ED-2 and ED-3, the incremental gain with ED-3 was modest, increasing sugar release by only 9.02 g L −1 relative to ED-2. Importantly, ED-1 resulted in sugar yields of 88.88 ± 3.64 to 106.86 ± 1.21 g L −1 , sufficient to achieve ethanol titers ≥40 g L −1 , the threshold required for industrial relevance. A semi-integrated bioprocess validated this outcome, producing 42.09 ± 2.38 g L −1 ethanol and an estimated yield of 213.38 L of ethanol per dry ton of pretreated biomass, requiring only 20.83 L of cellulase and 6.25 L of hemicellulase per ton. Remarkably, these enzyme dosages were approximately tenfold lower than those reported in prior studies.
The practical deployment of lithium–sulfur batteries (LSBs) is hindered by fundamental limitations in conventional slurry-cast cathodes, including poor sulfur utilization, sluggish ion transport, and low areal capacity, particularly in thick electrodes required for high energy density. To address these challenges, we present direct ink writing (DIW) as an additive manufacturing strategy to fabricate advanced current-collector-free, 3D-printed sulfur cathodes (3DP S@CoNi-DSACs/NC) with hierarchically porous architectures that enhance lithium-ion diffusion, promote electrolyte penetration, and reduce interfacial resistance. The synergistic effects of Co/Ni dual-atom sites accelerate redox kinetics and mitigate polysulfide shuttling. As a result, the optimized 3DP cathode with a sulfur loading of 5.4 mg cm −2 demonstrated excellent rate capability, delivering a high reversible capacity of 1041.4 mAh g −1 at 1C with 85.5% capacity retention after 1000 cycles, significantly outperforming its cast counterpart. Remarkably, even at a higher sulfur loading of 8.1 mg cm −2 , the 3DP cathode maintains outstanding performance, achieving a discharge capacity of 1538.4 mAh g −1 and an areal capacity of 12.5 mAh cm −2 at 0.1C. This study not only demonstrates the functional integration of catalytically active materials into 3D printable sulfur cathode architectures but also offers a scalable and transformative platform for building high-performance LSBs beyond conventional electrode manufacturing methods.
Not provided.
The synthesis of quinolinic acid from tryptophan is a critical step in the de novo biosynthesis of nicotinamide adenine dinucleotide (NAD + ) in mammals. Herein, the nonheme iron-based 3-hydroxyanthranilate-3,4-dioxygenase responsible for quinolinic acid production was studied by performing time-resolved in crystallo reactions monitored by UV-vis microspectroscopy, electron paramagnetic resonance (EPR) spectroscopy, and X-ray crystallography. Seven catalytic intermediates were kinetically and structurally resolved in the crystalline state, and each accompanies protein conformational changes at the active site. Among them, a monooxygenated, seven-membered lactone intermediate as a monodentate ligand of the iron center at 1.59-Å resolution was captured, which presumably corresponds to a substrate-based radical species observed by EPR using a slurry of small-sized single crystals. Other structural snapshots determined at around 2.0-Å resolution include monodentate and subsequently bidentate coordinated substrate, superoxo, alkylperoxo, and two metal-bound enol tautomers of the unstable dioxygenase product. These results reveal a detailed stepwise O-atom transfer dioxygenase mechanism along with potential isomerization activity that fine-tunes product profiling and affects the production of quinolinic acid at a junction of the metabolic pathway.
Regeneration of hyaline cartilage in human-sized joints remains a clinical challenge, and it is a critical unmet need that would contribute to longer healthspans. Injectable scaffolds for cartilage repair that integrate both bioactivity and sufficiently robust physical properties to withstand joint stresses offer a promising strategy. We report here on a hybrid biomaterial that combines a bioactive peptide amphiphile supramolecular polymer that specifically binds the chondrogenic cytokine transforming growth factor β-1 (TGFβ-1) and crosslinked hyaluronic acid microgels that drive formation of filament bundles, a hierarchical motif common in natural musculoskeletal tissues. The scaffold is an injectable slurry that generates a porous rubbery material when exposed to calcium ions once placed in cartilage defects. The hybrid material was found to support in vitro chondrogenic differentiation of encapsulated stem cells in response to sustained delivery of TGFβ-1. Using a sheep model, we implanted the scaffold in shallow osteochondral defects and found it can remain localized in mechanically active joints. Evaluation of resected joints showed significantly improved repair of hyaline cartilage in osteochondral defects injected with the scaffold relative to defects injected with the growth factor alone, including implantation in the load-bearing femoral condyle. These results demonstrate the potential of the hybrid biomimetic scaffold as a niche to favor cartilage repair in mechanically active joints using a clinically relevant large-animal model.
Abstract The manufacturing process of all-solid-state batteries necessitates the use of polymer binders. However, these binders, being ionic insulators by nature, can adversely affect charge transport within composite cathodes, thereby impacting the rate performance of the batteries. In this work, we aim to investigate the impact of fabrication methods, specifically the solvent-free dry process versus the slurry-cast wet process, on binder distribution and charge transport in composite cathodes of solid-state batteries. In the dry process, the binder forms a fibrous network, while the wet process results in binder coverage on the surface of cathode active materials. The difference in microstructure leads to a notable 20-fold increase in ionic conductivity in the dry-processed cathode. Consequently, the cells processed via the dry method exhibit higher capacity retention of 89% and 83% at C/3 and C/2 rates, respectively, in comparison to 68% and 58% for the wet-processed cells at the same rate. These findings provide valuable insights into the influence of fabrication methods on binder distribution and charge transport, contributing to a better understanding of the binder’s role in manufacturing of all-solid-state batteries.
Serial femtosecond crystallography (SFX) is a powerful technique that exploits X-ray free-electron lasers to determine the structure of macromolecules at room temperature. Despite the impressive exposition of structural details with this novel crystallographic approach, the methods currently available to introduce crystals into the path of the X-ray beam sometimes exhibit serious drawbacks. Samples requiring liquid injection of crystal slurries consume large quantities of crystals (at times up to a gram of protein per data set), may not be compatible with vacuum configurations on beamlines or provide a high background due to additional sheathing liquids present during the injection. Proposed and characterized here is the use of an immiscible inert oil phase to supplement the flow of sample in a hybrid microfluidic 3D-printed co-flow device. Co-flow generation is reported with sample and oil phases flowing in parallel, resulting in stable injection conditions for two different resin materials experimentally. A numerical model is presented that adequately predicts these flow-rate conditions. The co-flow generating devices reduce crystal clogging effects, have the potential to conserve protein crystal samples up to 95% and will allow degradation-free light-induced time-resolved SFX.
Automated, pulsed liquid-phase sample delivery has the potential to greatly improve the efficiency of both sample and photon use at pulsed X-ray facilities. In this work, an automated drop on demand (DOD) system that accelerates sample exchange for serial femtosecond crystallography (SFX) is demonstrated. Four different protein crystal slurries were tested, and this technique is further improved here with an automatic sample-cycling system whose effectiveness was verified by the indexing results. Here, high-throughput SFX screening is shown to be possible at free-electron laser facilities with very low risk of cross contamination and minimal downtime. The development of this technique will significantly reduce sample consumption and enable structure determination of proteins that are difficult to crystallize in large quantities. This work also lays the foundation for automating sample delivery.
Over the past two decades, serial X-ray crystallography has enabled the structure determination of a wide range of proteins. With the advent of X-ray free-electron lasers (XFELs), ever-smaller crystals have yielded high-resolution diffraction and structure determination. A crucial need to continue advancement is the efficient delivery of fragile and micrometre-sized crystals to the X-ray beam intersection. This paper presents an improved design of an all-polymer microfluidic `chip' for room-temperature fixed-target serial crystallography that can be tailored to broadly meet the needs of users at either synchrotron or XFEL light sources. The chips are designed to be customized around different types of crystals and offer users a friendly, quick, convenient, ultra-low-cost and robust sample-delivery platform. Compared with the previous iteration of the chip [Gilbile et al. (2021), Lab Chip , 21 , 4831–4845], the new design eliminates cleanroom fabrication. It has a larger imaging area to volume, while maintaining crystal hydration stability for both in situ crystallization or direct crystal slurry loading. Crystals of two model proteins, lysozyme and thaumatin, were used to validate the effectiveness of the design at both synchrotron (lysozyme and thaumatin) and XFEL (lysozyme only) facilities, yielding complete data sets with resolutions of 1.42, 1.48 and 1.70 Å, respectively. Overall, the improved chip design, ease of fabrication and high modifiability create a powerful, all-around sample-delivery tool that structural biologists can quickly adopt, especially in cases of limited sample volume and small, fragile crystals.
A quantitative description on dispersity of boehmite (γ-AlOOH) particles, a key component for waste slurry at Hanford sites, can provide useful knowledge for understanding various physicochemical nature of the waste. In this work, in situ liquid scanning electron microscopy (SEM) was used to evaluate the dispersity of particles in aqueous conditions using a microfluidic sample holder, System for Analysis at Liquid Vacuum Interface (SALVI). Secondary electron (SE) images and image analyses were performed to determine particle centroid locations and the distance to the nearest neighbour particle centroid, providing reliable rescaled interparticle distances as a function of ionic strength in acidic and basic conditions. Our finding of the particle dispersity is consistent with physical insights from corresponding particle interactions under physicochemical conditions, demonstrating delicate changes in dispersity of boehmite particles based on novel in situ liquid SEM imaging and analysis.
This special issue celebrates the scientific legacy of Dr. Malcolm J. Andrews, former Editor of the ASME Journal of Fluids Engineering (2010–2018). Malcolm devoted his career to the development and applications of computational, experimental, and analytical tools to investigate and solve diverse, complex fluid dynamics, and heat transfer problems. Malcolm’s most notable research accomplishments include: (i) contributions to innovative experiments, simulations, and theory to understand buoyancydriven turbulent mixing due to Rayleigh–Taylor instability; (ii) development of the multiphase particle-in-cell method for understanding fragmentation in spray jets, coal-water slurry, and other dense particulate flows; (iii) mixing in nano- and biomaterials in applications ranging from protein glues to carbon nanotube composites; (iv) determining dispersion in proteins to improve therapeutic drug delivery via micro-encapsulation; (v) innovative methods for storing information using nanopinned dipole magnetic vortices in superconducting materials; and (vi) modeling and design modifications for shell-and-tube heat exchangers, as well as heat transfer in rotating systems such as turbine blades. The results of his research have been published in a long series of trend-setting journal and conference papers, book chapters, and patents.
A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.
We report time-of-flight secondary ion mass spectrometry (ToF-SIMS) was performed for boehmite (AOH-60) and its potential products of oxidation including pseudo-boehmite (AOH-180), α- and γ-Al 2 O 3 , and α- and γ-Al(OH) 3 . Since boehmite is often incorporated on cladding materials to prevent corrosion, surface analysis techniques are performed to determine the amount of oxidation present. This ToF-SIMS spectral library is of significance because it includes boehmite and its potential oxidation products (i.e., aluminum oxide and hydroxide), which can be used to compare to spectra obtained for real-world samples containing boehmite. Furthermore, ToF-SIMS is often used as a complementary technique to x-ray photoelectron spectroscopy due to its surface sensitivity and ability to compare spectra via a multivariate analysis, therefore establishing that the molecular signatures of boehmite and relevant compounds are essential for peak identification. The SIMS spectra shown are acquired from commercially available powders, which were deposited onto a silicon wafer substrate via liquid slurry drop casting. This library of SIMS mass spectra will serve as a comparison of boehmite [γ-AlO(OH)], pseudo-boehmite [AlOOH∙nH 2 O], α- and γ-Al 2 O 3 aluminum oxide, and α- and γ-Al 2 O 3 aluminum hydroxide in the negative ion mode, which compliments those reported in the positive ion mode.
We report time-of-flight secondary ion mass spectrometry (ToF-SIMS) was performed for boehmite (AOH-60) and its potential products of oxidation including pseudo-boehmite (AOH-180), α- and γ-Al 2 O 3 , and α- and γ-Al(OH) 3 . Since boehmite often forms on the cladding materials to prevent corrosion, surface analysis techniques are performed to determine the amount of oxidation present. This ToF-SIMS spectral library is of significance because it includes boehmite and its potential oxidation products (i.e., aluminum oxide and hydroxide), which can be used to compare to spectra obtained for real-world samples containing boehmite. Furthermore, ToF-SIMS is often used as a complementary technique to x-ray photoelectron spectroscopy (XPS) due to its surface sensitivity and ability to compare spectra via multivariate analysis, therefore establishing the molecular signatures of boehmite and relevant compounds are essential for peak identification. The SIMS spectra shown are acquired from commercially available powders, which were deposited onto a Si wafer substrate via liquid slurry drop casting. This library of SIMS mass spectra will serve as a comparison of boehmite [γ-AlO(OH)], pseudo-boehmite [AlOOH∙nH 2 O], α- and γ-Al 2 O 3 aluminum oxide, and α- and γ-Al 2 O 3 aluminum hydroxide in the positive ion mode, which compliments those reported in the negative ion mode (Part 1).
Lignocellulosic biomass is a feedstock for fuels and chemicals that does not compete with food resources and has less contaminants than refuse-derived biomass feedstocks. To convert lignocellulosics to biofuels or value-added products, multiple processing steps are typically necessary. One method of producing biofuels from lignocellulosic biomass utilizes a deacetylation and mechanical refining pretreatment and an enzymatic hydrolysis reaction to produce fermentable sugars from cellulose and hemicellulose. The rheological properties of biomass, such as yield stress and plastic viscosity, change during enzymatic hydrolysis and alter the energy requirements for pumping and mixing, an important consideration for the design of processing equipment. The dynamic changes in rheological properties that occur in a corn stover feedstock undergoing enzymatic hydrolysis are characterized in this work, and the influence on pressure losses in piping systems is estimated. Two rheometer geometries were fabricated with stereolithography 3D printing to reduce wall slip and sample ejection. The slurries have complex rheological behaviors that include shear-thinning behavior. Shear stress ramps were performed on samples at 20 and 50 degrees C using the custom geometries, and the Herschel-Bulkley model was fit to the data. The dynamic nature of the rheological properties is correlated with changes in the average fiber length at various extents of reaction, and the influence of solids concentration on the observed rheology and piping pressure losses is discussed.
Silicon-dominant anodes are of great interest because of their potential to boost the cell-level energy of state-of-the-art Li-ion batteries. While silicon materials have been extensively studied, understanding interactions at the electrode level has recieved little attention, especially the coating process of Si particles, which plays an equally important role in unlocking the full potential of silicon anodes. Herein, the electrode processing of a Si-dominated anode (52.8 wt%, 3.5–4.5 mAh cm −2 ) is being investigated to understand the relationship of processing on the morphology and properties of Si anodes at the electrode level. It has been found that almost-undetectable Si agglomerates easily form during electrode processing, which grow into largeprotrusions after lithiation and trigger potential internal shorting and self-discharge problems. A facile slurry filtration step is proposed to homogenize the particle distribution within Si-dominant electrodes which improves the electrochemical performance and storage stability of Si-based Li ion batteries.
High oxygen permeability ionomers (HOPIs) are being developed as an alternative to conventional perfluorosulfonic (PFSA) ionomers for cathodes in proton exchange membrane fuel cells (PEMFCs). HOPIs aim to reduce local oxygen transport resistance, improving performance and reducing degradation as the catalyst loses surface area. However, HOPIs' more rigid, 3D backbone leads to increased crack density in the cathode, potentially causing accelerated degradation. This study investigates crack formation in HOPI-based and PFSA-bound catalyst layers (CLs). We conducted a comprehensive parametric study to identify conditions and catalyst slurry components that minimize cracking. CLs were fabricated with various ionomer and catalyst types, under different relative humidity (RH) levels, solids weight percentages, solvent ratios, and ionomer-to-carbon ratios (I/C). Results show that HOPI-based CLs exhibit less cracking when fabricated under low RH conditions, with lower solids weight percentage, higher alcohol content, and lower I/C. Additionally, catalysts with low/medium surface area carbon supports show less cracking than those with high surface area carbon supports.