Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Effects of Winglets on the Drag of a Low-Aspect-Ratio Configuration

A wind-tunnel investigation has been performed to determine the effect of winglets on the induced drag of a low-aspect-ratio wing configuration at Mach numbers between 0.30 and 0.85 and a nominal angle-of-attack range from -2 deg to 20 deg. Results of the tests at the cruise lift coefficient showed significant increases in lift-drag ratio for the winglet configuration relative to a wing-alone configuration designed for the same lift coefficient and Mach number. Further, even larger increases in lift-drag ratio were observed at lift coefficients above the design value at all Mach numbers tested. The addition of these winglets had a negligible effect on the static lateral-directional stability characteristics of the configuration. No tests were made to determine the effect of these winglets at supersonic Mach numbers, where increases in drag caused by winglets might be more significant. Computational analyses were also performed for the two configurations studied. Linear and small-disturbance formulations were used. The codes were found to give reasonable performance estimates sufficient for predicting changes of this magnitude.

Smith, Leigh Ann↗
NASA NTRS1996

Wind-tunnel development of an SR-71 aerospike rocket flight test configuration

A flight experiment has been proposed to investigate the performance of an aerospike rocket motor installed in a lifting body configuration. An SR-71 airplane would be used to carry the aerospike configuration to the desired flight test conditions. Wind-tunnel tests were completed on a 4-percent scale SR-71 airplane with the aerospike pod mounted in various locations on the upper fuselage. Testing was accomplished using sting and blade mounts from Mach 0.6 to Mach 3.2. Initial test objectives included assessing transonic drag and supersonic lateral-directional stability and control. During these tests, flight simulations were run with wind-tunnel data to assess the acceptability of the configurations. Early testing demonstrated that the initial configuration with the aerospike pod near the SR-71 center of gravity was unsuitable because of large nosedown pitching moments at transonic speeds. The excessive trim drag resulting from accommodating this pitching moment far exceeded the excess thrust capability of the airplane. Wind-tunnel testing continued in an attempt to find a configuration suitable for flight test. Multiple configurations were tested. Results indicate that an aft-mounted model configuration possessed acceptable performance, stability, and control characteristics.

Smith, Stephen C.↗
NASA NTRS1996

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Lepsch, Roger A., Jr.↗
NASA NTRS1959

Measurements Obtained During the First Landing of the North American X-15 Research Airplane

The first landing of the X-15 airplane was made at 8:43 a.m., June 8, 1959, on the hard surface of Rogers Dry Lake. One purpose of the first-glide flight was to evaluate the effectiveness of the landing-gear system. Some results are presented of the landing-approach characteristics, the impact period, and the runout phase of the landing maneuver. The results indicate that the touchdown was accomplished at a vertical velocity of 2.0 feet per second for the main gear and 13.5 feet per second for the nose gear. These vertical velocities were within the values of sinking speeds established by structural design limitations. However, permanent structural deformation occurred in the main-landing-gear system as a result of the landing, and a reevaluation of the gear is being made by the manufacturer. The landing occurred at a true ground speed of 158 knots for main-gear touchdown at an angle of attack of 8.50. The incremental acceleration at the main gear was 2.7g and 7.39 at the nose gear as a result of the landing. The incremental acceleration at the center of gravity of the airplane was 0.6g for the main-gear impact and 2.4g for the nose-gear impact. The incremental acceleration at the main gear as a result of the nose-gear impact was 4.8g. The extreme rearward location of the main-gear skids appears to offer satisfactory directional stability characteristics during the run- out phase of the landing. No evidence of nosewheel shimmy was indicated during the impact and runout phase of the landing despite the absence of a shimmy damper on the nose gear. The maximum amount of skid wear as a result of the landing was on the order of 0.005 inch. No appreciable amount of tire wear was indicated for the dual, corotating nosewheels.

McKay, James M.↗
NASA NTRS1959

Launch, Low-Speed, and Landing Characteristics Determined from the First Flight of the North American X-15 Research Airplane

The first flight of the North American X-15 research airplane was made on June 8, 1959. This was accomplished after completion of a series of captive flights with the X-15 attached to the B-52 carrier airplane to demonstrate the aerodynamic and systems compatibility of the X-15//B-52 combination and the X-15 subsystem operation. This flight was planned as a glide flight so that the pilot need not be concerned with the propulsion system. Discussions of the launch, low-speed maneuvering, and landing characteristics are presented, and the results are compared with predictions from preflight studies. The launch characteristics were generally satisfactory, and the X-15 vertical tail adequately cleared the B-52 wing cutout. The actual landing pattern and landing characteristics compared favorably with predictions, and the recommended landing technique of lowering the flaps and landing gear at a low altitude appears to be a satisfactory method of landing the X-15 airplane. There was a quantitative correlation between flight-measured and predicted lift-drag-ratio characteristics in the clean configuration and a qualitative correlation in the landing configuration. A longitudinal-controllability problem, which became severe in the landing configuration, was evident throughout the flight and, apparently, was aggravated by the sensitivity of the side-located control stick. In the low-to-moderate angle-of-attack range covered, the longitudinal and directional stability were indicated to be adequate.

Finch, Thomas W.↗
NASA NTRS1999

An Experimental Database for Conventional and Alternate Control Concepts on the HSR 1.675% Reference H Model

The objective was to experimentally evaluate the longitudinal and lateral-directional stability and control characteristics of the Reference H configuration at supersonic and transonic speeds. A series of conventional and alternate control devices were also evaluated at supersonic and transonic speeds. A database on the conventional and alternate control devices was to be created for use in the HSR program.

McMillin, Naomi↗
NASA NTRS1949

A Preliminary Analysis of the Flying Qualities of the Consolidated Vultee MX-813 Delta-Wing Airplane Configuration at Transonic and Low Supersonic Speeds as Determined from Flights of Rocket-Powered Models

A preliminary analysis of the flying qualities of the Consolidated Vultee MX-813 delta-wing airplane configuration has been made based on the results obtained from the first two 1/8 scale models flown at the NACA Pilotless Aircraft Research Station, Wallop's Island, VA. The Mach number range covered in the tests was from 0.9 to 1.2. The analysis indicates adequate elevator control for trim in level flight over the speed range investigated. Through the transonic range there is a mild trim change with a slight tucking-under tendency. The elevator control effectiveness in the supersonic range is reduced to about one-half the subsonic value although sufficient control for maneuvering is available as indicated by the fact that 10 deg elevator deflection produced 5g acceleration at Mach number of 1.2 at 40,000 feet.The elevator control forces are high and indicate the power required of the boost system. The damping. of the short-period oscillation is adequate at sea-level but is reduced at 40,000 feet. The directional stability appears adequate for the speed range and angles of attack covered.

Mitcham, Grady L.↗
NASA NTRS2004

Buffet Load Alleviation

High performance aircraft are, by their very nature, often required to undergo maneuvers involving high angles of attack. Under these conditions unsteady vortices emanating from the wing and the fuselage will impinge on the twin fins (required for directional stability) causing excessive buffet loads, in some circumstances, to be applied to the aircraft. These loads result in oscillatory stresses, which may cause significant amounts of fatigue damage. Active control is a possible solution to this important problem. A full-scale test was carried out on an F/A-18 fuselage and fins using piezoceramic actuators to control the vibrations. Buffet loads were simulated using very powerful electromagnetic shakers. The first phase of this test was concerned with the open loop system identification whereas the second stage involved implementing linear time invariant control laws. This paper looks at some of the problems encountered as well as the corresponding solutions and some results. It is expected that flight trials of a similar control system to alleviate buffet will occur as early as 2001.

Ryall, T. G.↗
NASA NTRS1953

Flight Test Results of Rocket-Propelled Buffet-Research Models Having 45 Degree Sweptback Wings and 45 Degree Sweptback Tails Located in the Wing Chord Plane

Three rocket-propelled buffet-research models have been flight tested to determine the buffeting characteristics of a swept-wing- airplane configuration with the horizontal tail operating near the wing wake. The models consisted of parabolic bodies having 45deg sweptback wings of aspect ratio 3.56, at aspect ratio of 0.3, NACA 64A007 airfoil sections, and tail surfaces of geometry and section identical to the wings. Two tests were conducted with the horizontal tail located in the wing chord plane with fixed incidence angles of -1.5deg on one model and 0deg on the other model. The third test was conducted with no horizontal tail. Results of these tests are presented as incremental accelerations in the body due to buffeting, trim angles of attack, trim normal- and side-force coefficients, wing-tip helix angles, static-directional-stability derivatives , and drag coefficients plotted against Mach number. These data indicate that mild low-lift buffeting was experienced by all models over a range of Mach number from approximately 0.7 to 1.4. It is further indicated that this buffeting was probably induced by wing-body interference and was amplified at transonic speeds by the horizontal tail operating in the wing wake. A longitudinal trim change was encountered by the tail-on models at transonic speeds, but no large changes in side force and no wing dropping were indicated.

Mason, Homer P.↗
NASA NTRS1937

Notes on Factors Affecting Geometrical Arrangement of Tricycle-Type Landing Gear

The effects of the geometrical arrangement of tricycle landing gears on various characteristics of an airplane equipped with such landing gear is discussed. The characteristics discussed include directional stability, overturning tendencies, steering and ground handling, shimmy, takeoff, and porpoising. The conclusions are summarized in a table.

Wenzinger, Carl J.↗
NASA NTRS1949

Full-Scale Hydrodynamic Evaluation of a Modified Navy J4F-2 Amphibian with a 0.425-Scale XP5M-1 Hull Bottom. TED No. NACA DE325

An investigation was made to evaluate the hydrodynamic qualities of a 0.425-scale model of the Navy XP5M-1 hull, which was installed on a modified Navy J4F-2 amphibian. Longitudinal and directional stability during take-off and landing, low-speed maneuverability, spray characteristics, and take-off performance were investigated. The behavior of the airplane in moderately rough water was also observed. The opinions of three pilots have been correlated with the data.

Land, Norman S.↗
NASA NTRSDate not supplied

Principles for Termination of Medical Care in Austere Analog Environments for Development of Spaceflight Protocols

INTRODUCTION: When compared to operations in low earth orbit, exploration class missions will have substantially limited resources and ground medical support while the risk of a significant medical event is projected to be higher. Termination of care (TOC) may need to be considered in certain instances. We aim to utilize data from earth-based analogs to identify common principles that can help develop future guidelines to this complex medical and ethical challenge. METHODS: A comprehensive literature review was conducted in medline, nasa.gov, Defense Technical Information Center(DTIC) and google scholar. Key search terms including “withdrawal of care, termination of care, termination of CPR, military medicine, wilderness medicine, futility, potentially inappropriate” and others were used to identify analog studies of relevance. These were qualitatively evaluated for recurring principles or themes that were reviewed and structured. RESULTS: Mission planning termination of care principles: definitions of clear medical goals, separate protocols for each relevant condition, protocols developed using best available evidence, crew involvement in development, protocols rehearsal pre-launch, and inclusion of palliative capabilities. In-mission termination of care principles: 1. Crew Medical Officer directed stabilization of the patient; 2. Consultation with mission control with standardized information exchange; 3. Multidisciplinary medical and ethical conference among the mission directors, flight surgeons and relevant specialist experts; 4. Multidisciplinary risk review examining both medical and mission risks for relevant options; 5. Provision of a transparent explanation of the process and decision to crew; 6. Allowing crew feedback and inquiry to review board; 7. Support of the crew in the enacted decision. DISCUSSION: By utilizing the best available evidence in conjunction with expert opinion we have identified common principles from earth-based analogs that could be used to help design future TOC protocols.

Samuel Stephenson↗
DOE OSTI2024

Transient Stability Analysis of Direct Droop-Controlled Grid-Forming Inverter with Current Clipping as Current Limiting Control

This paper investigates the transient stability of the direct droop-controlled grid-forming (GFM) inverter which employs the current clipping-based approach for overcurrent limitation. An equivalent circuit model of the direct-droop GFM inverter with current clipping is developed for this purpose. It is shown that during overcurrent conditions, the GFM inverter with current clipping acts as a voltage source with a virtual resistance behind the inverter filters. To compute the parameters of this virtual resistance an analytical expression is given in the paper. Then utilizing the developed circuit, a criteria to exit current limiting during post-fault conditions is given. The developed analytical approaches are then validated through electromagnetic transient (EMT) simulation results in PSCAD software and finally concluding remarks are drawn.

Mohiuddin, Sheik Mohammad↗
NASA NTRS1978

An extension of A-stability to alternating direction implicit methods

An alternating direction implicit (ADI) scheme was constructed by the method of approximate factorization. An A-stable linear multistep method (LMM) was used to integrate a model two-dimensional hyperbolic-parabolic partial differential equation. Sufficient conditions for the A-stability of the LMM were determined by applying the theory of positive real functions to reduce the stability analysis of the partial differential equations to a simple algebraic test. A linear test equation for partial differential equations is defined and then used to analyze the stability of approximate factorization schemes. An ADI method for the three-dimensional heat equation is also presented.

Warming, R. F.↗
NASA NTRS1992

A new direction in hydrodynamic stability: Beyond eigenvalues

Fluid flows that are smooth at low speeds become unstable and then turbulent at higher speeds. This phenomenon has traditionally been investigated by linearizing the equations of flow and looking for unstable eigenvalues of the linearized problem, but the results agree poorly in many cases with experiments. Nevertheless, it has become clear in recent years that linear effects play a central role in hydrodynamic instability. A reconciliation of these findings with the traditional analysis can be obtained by considering the 'pseudospectra' of the linearized problem, which reveals that small perturbations to the smooth flow in the form of streamwise vortices may be amplified by factors on the order of 10(exp 5) by a linear mechanism, even though all the eigenmodes are stable. The same principles apply also to other problems in the mathematical sciences that involve non-orthogonal eigenfunctions.

Trefethen, Lloyd N.↗