SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Wind tunnel tests of propellor driven, deflected slipstream, short takeoff aircraft model to determine longitudinal and lateral-directional stability when in ground effect
The YOV-10A Research Aircraft was flown to obtain flyover noise data that could be compared to noise data measured in the 40- by 80- foot wind tunnel at NASA Ames Research Center. The flyover noise measurements were made during the early morning hours on runway 32L at Moffett Field, California. A number of passes were made at 50 ft altitude in level flight with an airplane configuration closely matching that tested in the wind tunnel. Two passes were selected as prime and were designated for full data reduction. The YOV-10A was flown over a microphone field geometrically similar to the microphone array set up in the wind tunnel. An acoustic center was chosen as a matching point for the data. Data from the wind tunnel and flyover were reduced and appropiate corrections were applied to compare the data. Results show that wind tunnel and flight test acoustic data agreed closely.
Handling qualities criteria and operational performance margins have been determined for the landing phase of commercial short-takeoff-and-landing airplanes. The requirements are the result of a literature survey, analysis of areas found to be inadequately covered by current criteria, and a subsequent piloted simulator investigation of critical criteria requiring substantiation. Three complete simulator models were used, each describing the characteristics of a different high-lift system, the externally blown flap, the augmentor flap, and the internally blown flap. The proposed criteria are presented with substantiating discussions from currently available data or directly from the results of this simulation work where it is applicable.
An exploratory wind tunnel test has been conducted at Mach numbers from 0.60 to 0.80 to investigate the effects of nozzle geometry and upper surface blowing on the aerodynamic characteristics of a 14-percent-thick airfoil. Measured data included lift, drag, pitching moments, surface pressures, and nozzle thrust.
The impact of short takeoff and landing aircraft in meeting the needs of short haul transportation systems is analyzed. The objectives of the short haul system are evaluated on the basis of the following criteria: (1) service to the passenger, (2) economic viability, and (3) terminal area environment conditions caused by community noise, ground and air decongestion, and air pollution. Data are presented in the forms of tables, charts, and graphs. An itemization of the conclusions reached after the preliminary investigation is included.
The characteristics for a quiet turbofan short takeoff aircraft for short haul transportation applications are discussed. The following subjects are examined: (1) representative aircraft configurations, characteristics, and costs associated with the short haul aircraft development and operation, (2) critical technology and technology related problems to be resolved in successful introduction of representative short haul aircraft, (3) relationships between quiet short takeoff aircraft and the economic and social viability of short haul, and (4) identification of high payoff technology areas. In order to properly evaluate the candidate aircraft designs and to determine their economic viability and community acceptance, a real world scenario was developed and projected to 1990.
For abstract, see
A NASA propulsive-lift technology program for short takeoff aircraft is discussed. In the propulsive-lift program, turbofan engine power is used to augment the lift of essentially conventional wings. Potentially important applications of the propulsive lift developments for various aircraft operating conditions are reported. It is stated that the objective of the program is to provide technical information on the design, development, operation, and regulation of propulsive-lift aircraft.
The program to design and build a Buffalo/Spey Augmentor-Wing research aircraft is presented. The development of an internally blown flap system for the generation of powered lift is discussed. Modification, development, and testing of the Rolls-Royce Spey engine are reported. The ground tests and first flights of the aircraft are described and the application of the internally blown flap concept for short takeoff military transport aircraft is proposed.
Previous work in the development of quantitative models for the prediction of passenger reaction to motion and vehicle environment parameters in flight was extended to include a class of aircraft appropriate for low-density, short-haul service. The results indicate that it is possible to obtain quantitative response inputs from an usually small special test-subject group which will be representative of the general traveling public. Additional data which indicate the importance of comfort as a factor in evaluating ride quality was obtained, and identification of the factors which contribute to judgments regarding comfort level was improved. Seat comfort and seat spacing is very vital in the smaller aircraft. Mathematical modeling applied in conjuction with passenger reaction data was shown to be very useful for establishing ride-quality design criteria.
A project to develop an experimental aircraft for use as an inflight demonstrator of the augmentor wing, short takeoff concept is discussed. The required modifications were made on a de Havilland C-8A aircraft. The modifications to the aircraft are explained and the performance of the modified aircraft is reported.
A study of quiet turbofan short takeoff aircraft for short haul air transportation was conducted. The objectives of the study were to: (1) define representative aircraft configurations, characteristics, and costs associated with their development, (2) identify critical technology and technology related problems to be resolved in successful introduction of representative short haul aircraft, (3) determine relationships between quiet short takeoff aircraft and the economic and social viability of short haul, and (4) identify high payoff technology areas.
Proceedings of conference on short takeoff and landing aircraft to determine aerodynamic characteristics and short haul transportation applications
Wind tunnel tests to determine the aerodynamic characteristics of basically similar short takeoff aircraft were conducted. The investigations were designed to provide data for a systematic direct comparison of five of the concepts considered. The configurations of the five models are illustrated and described. The aerodynamic data are presented in the form of graphs. It was concluded that the most complex systems require the least amount of net thrust.
Small-scale-model data have shown large static loads on the flap system behind the engines. The large-scale-model tests confirmed the magnitude of these loads and indicated that the relative loading of each flap element depends on the engine-wing-flap geometry. Flap response measurements indicated that the unsteady pressure loading excited the natural vibration modes of the flap system on this model. Since this was a boilerplate model, the only conclusion that can be drawn is that the possibility of large vibration loads must be considered for a flight-weight structure. The similarity of the unsteady pressure and flap response spectra for the wind-off and wind-on cases indicated that it may be possible to realistically test flight-weight flap structures on a static test stand rather than endure the extra costs and scheduling problems associated with large-scale wind-tunnel tests. There is a potential flap-temperature problem which if not resolved might preclude the use of materials such as aluminum and the composites in the flap structure.
The considerations involved in making a piloted simulator an effective research tool in the design and development of new aircraft are discussed. An assessment of the limitations of the simulator in depicting real flight as well as the problem of recognizing erroneous results when the simulator is supplied with incorrect input data is made. Examples of the ways in which the simulator is used to design and develop the augmentor-wing aircraft are presented. Four areas of investigation are: (1) to design the lateral control system for proper feel and response, (2) determine the effect of engine failure during approach, (3) develop the best technique for controlling flight path during approach, and (4) the significance of lift loss in ground effect and how to compensate for such loss.
The responses of people to special noise characteristics associated with short takeoff aircraft are discussed. The findings of studies which have yielded data that may be pertinent to community acceptance of short takeoff aircraft noise are presented. A three step program to evaluate public acceptance of short takeoff aircraft noise was conducted. The three steps were: (1) definition of short takeoff aircraft noise characteristics, (2) laboratory tests to evaluate individual responses, and (3) the use of community survey data to extrapolate conventional takeoff aircraft experience.
Explore the source record for details and available documents.