Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shell Buckling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

GENERAL INSTABILITY OF ORTHOGONALLY STIFFENED CYLINDRICAL SHELLS

Earlier research at the National Aeronautics Research Institute (N.L.R.), Amsterdam, which forms the basis of recent work is reviewed. This early work refers to 2 schemes: the orthotropic shell and, in view of buckling modes where the half wave length is of the order of the ring distance, the shell with continuously distributed stringers and discrete rings. Linear theory is considered to be adequate for these structures, where the imperfections are small in comparison to the height of the ring sections. Recent developments account for pressure difference in addition to axial compression, for the correct stiffness matrix of skin panels in the post-buckling stage and for stringer bending due to hoop stresses in the skin, which are of importance as has been shown by the investigation of the post-buckling behaviour. Numerical data for the stiffness matrix of skin panels have been established. Numerical evaluation of the stability equation has not been performed as yet.

SHELL STABILITY↗

Future Directions and Challenges in Shell Stability Analysis

An answer is sought to the question how comes that today, in 1997, after so many years of concentrated research effort, when it comes to designing buckling critical thin walled shells, one cannot do any better than using the rather conservative Lower Bound Design Philosophy of the sixties. It will be shown that with the establishment of Initial Imperfection Data Banks and the introduction of Probabilistic Design Procedures one has, what appears to be, a viable alternative that when used judiciously may lead step by step to improved shell design recommendations.

Arbocz, Johann↗

Summary of Research Report

Ten papers, published in various publications, on buckling, and the effects of imperfections on various structures are presented. These papers are: (1) Buckling mode localization in elastic plates due to misplacement in the stiffner location; (2) On vibrational imperfection sensitivity on Augusti's model structure in the vicinity of a non-linear static state; (3) Imperfection sensitivity due to elastic moduli in the Roorda Koiter frame; (4) Buckling mode localization in a multi-span periodic structure with a disorder in a single span; (5) Prediction of natural frequency and buckling load variability due to uncertainty in material properties by convex modeling; (6) Derivation of multi-dimensional ellipsoidal convex model for experimental data; (7) Passive control of buckling deformation via Anderson localization phenomenon; (8)Effect of the thickness and initial im perfection on buckling on composite cylindrical shells: asymptotic analysis and numerical results by BOSOR4 and PANDA2; (9) Worst case estimation of homology design by convex analysis; (10) Buckling of structures with uncertain imperfections - Personal perspective.

Elishakoff, Isaac↗

Scaling Methodology for Buckling of Sandwich Composite Cylindrical Structures

The study of the buckling behavior of large shell structures through full-size tests can be complex and expensive. Therefore, scaled structures are often preferred to investigate the buckling behavior efficiently. However, it can be difficult to design scaled structures that are representative of the full-scale structures. Herein, an analytical scaling methodology for compression-loaded sandwich composite cylinders based on the nondimensionalization of the buckling equations is presented. The methodology is used to develop scaled configurations that show a similar buckling response. Both the baseline and the scaled configurations are verified by finite-element analysis. Limitations of the methodology are discussed and are a result of neglecting the flexural anisotropy and the transverse shear compliance.

Balbin, Ines Uriol↗

Buckling Design Studies of Inverted, Oblate Bulkheads for a Propellant Tank

An investigation of the deformation and buckling characteristics of a composite, oblate bulkhead that has an inverted geometry and is subjected to pressure-only loading is presented for three bulkhead geometries and thicknesses. The effects of a stiffening support ring at the bulkhead to cylinder interface are also evaluated. Buckling analyses conducted using the axisymmetric shell code BOSOR4 are discussed for several bulkhead configurations. These results are analytically verified using results from the Structural Analysis of General Shells (STAGS) code for a selected bulkhead configuration. The buckling characterization of an inverted, oblate bulkhead requires careful attention as small changes in bulkhead parameters can have a significant effect on the critical buckling load. Comparison of BOSOR4 and STAGS results provided a very good correlation between the two analysis methods. In addition, the analysis code BOSOR4 was found to be an efficient sizing tool that is useful during the preliminary design stage of a practical shell structure. Together, these two aspects should give the design engineer confidence in sizing these stability critical structures. Additional characterization is warranted, especially for a composite tank structure, since only one bulkhead configuration was examined closely.

Smeltzer, Stanley S., III↗

Testing and Analyses of Advanced Composite Tow-Steered Shells with Cutouts

The structural response of two composite tow-steered shells with small cutouts in end compression is assessed using analyses and experimental measurements. The cylindrical shells were manufactured without cutouts using an automated fiber placement system, where the shells’ fiber orientation angles vary continuously around the shell circumference from ±10 degrees on the axially stiff crown and keel, to ±45 degrees on the shear-stiff sides. The first shell with overlaps has laminate thickness variations on the crown and keel that result from application of all 24 tows during each pass of the fiber placement system. The second shell without overlaps uses the fiber placement system’s tow drop/add capability to achieve a more uniform shell wall thickness. These shells without cutouts were tested in axial compression and buckled elastically. An unreinforced cutout representative of a passenger door on a commercial aircraft fuselage is machined into one side of each shell. Results from nonlinear finite element analysis are compared with their corresponding load, displacement, and strain measurements in prebuckling through stable postbuckling. Results from tests and analyses of shells with large cutouts are also discussed. The very good agreement observed in this study increases confidence in applying tow-steered composites to operational vehicles.

Tow-Steered↗

Test and Analysis of a Buckling-Critical Large-Scale Sandwich Composite Cylinder

Structural stability is an important design consideration for launch-vehicle shell structures and it is well known that the buckling response of such shell structures can be very sensitive to small geometric imperfections. As part of an effort to develop new buckling design guidelines for sandwich composite cylindrical shells, an 8-ft-diameter honeycomb-core sandwich composite cylinder was tested under pure axial compression to failure. The results from this test are compared with finite-element-analysis predictions and overall agreement was very good. In particular, the predicted buckling load was within 1% of the test and the character of the response matched well. However, it was found that the agreement could be improved by including composite material nonlinearity in the analysis, and that the predicted buckling initiation site was sensitive to the addition of small bending loads to the primary axial load in analyses.

Schultz, Marc R.↗

EFFECTS OF MODES OF INITIAL IMPERFECTIONS ON THE STABILITY OF CYLINDRICAL SHELLS UNDER AXIAL COMPRESSION

The effects of definite and "indefinite" initial imperfections on the buckling and post buckling behavior of an axially compressed cylindrical shell are analyzed by a nonlinear theory. The definite initial imperfections considered do not contribute to the reduction of the peak buckling load; while the "indefinite" imperfections, expressed in terms of a single factor introduced by Donnell 1 , cause a reduction in the buckling strength. The physical meaning of the imperfection factor, however, needs further clarification. Two theoretical buckling processes are found to be possible. In the early stage of buckling, the cylinder may deform with a comparatively large number of waves of small amplitudes or the cylinder may deform with a comparatively small number of waves of large amplitudes. Further theoretical and experimental studies of the effects of initial imperfections and the process of buckling are suggested.

AXIAL COMPRESSION↗

Nonlinear Finite Element Analysis of Shells with Large Aspect Ratio

A higher order degenerated shell element with nine nodes was selected for large deformation and post-buckling analysis of thick or thin shells. Elastic-plastic material properties are also included. The post-buckling analysis algorithm is given. Using a square plate, it was demonstrated that the none-node element does not have shear locking effect even if its aspect ratio was increased to the order 10 to the 8th power. Two sample problems are given to illustrate the analysis capability of the shell element.

Chang, T. Y.↗

Dynamic buckling estimates.

Dynamic buckling of imperfection sensitive models, specifically cylindrical shells under axial compression

AXIAL COMPRESSION↗

Finite Element Analysis of Geodesically Stiffened Cylindrical Composite Shells Using a Layerwise Theory

Layerwise finite element analyses of geodesically stiffened cylindrical shells are presented. The layerwise laminate theory of Reddy (LWTR) is developed and adapted to circular cylindrical shells. The Ritz variational method is used to develop an analytical approach for studying the buckling of simply supported geodesically stiffened shells with discrete stiffeners. This method utilizes a Lagrange multiplier technique to attach the stiffeners to the shell. The development of the layerwise shells couples a one-dimensional finite element through the thickness with a Navier solution that satisfies the boundary conditions. The buckling results from the Ritz discrete analytical method are compared with smeared buckling results and with NASA Testbed finite element results. The development of layerwise shell and beam finite elements is presented and these elements are used to perform the displacement field, stress, and first-ply failure analyses. The layerwise shell elements are used to model the shell skin and the layerwise beam elements are used to model the stiffeners. This arrangement allows the beam stiffeners to be assembled directly into the global stiffness matrix. A series of analytical studies are made to compare the response of geodesically stiffened shells as a function of loading, shell geometry, shell radii, shell laminate thickness, stiffener height, and geometric nonlinearity. Comparisons of the structural response of geodesically stiffened shells, axial and ring stiffened shells, and unstiffened shells are provided. In addition, interlaminar stress results near the stiffener intersection are presented. First-ply failure analyses for geodesically stiffened shells utilizing the Tsai-Wu failure criterion are presented for a few selected cases.

Gerhard, Craig Steven↗