Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stability and transition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Instabilities orginating from suction holes used for Laminar Flow Control (LFC)

A small-scale wind tunnel previously used for turbulent boundary layer studies has been modified for experiments in laminar flow control. The facility incorporates suction through interchangeable porous test surfaces which are used to stabilize the boundary layer and delay transition to turbulent flow. The thin porous test surfaces are supported by a baffled plenum chamber box which also acts to gather the flow through the surface into tubes which are routed to a high pressure fan. An elliptic leading edge is attached to the assembly to establish a new layer on the test plate. A slot is used to remove the test section flow below the leading edge. The test section was lengthened and fitted with a new ceiling. Substantial modifications were also made to the 3D probe traverse. Detailed studies have been made using isolated holes to explore the underlying instability mechanisms. The suction is perturbed harmonically and data are averaged on the basis of the phase of the disturbance. Conditions corresponding to strong suction and without suction have been studied. In both cases, 3D contour surfaces in the vicinity of the hole show highly three-dimensional T-S waves that fan out away from the hole with streamwise distance. With suction, the perturbations on the centerline are much stronger and decay less rapidly, while the far field is similar to the case without suction. Downstream the contour surfaces of the bow-shaped TS waves develop spanwise irregularities which eventually form into clumps. The contours remain smooth when suction is not applied. Even without suction, the harmonic point source is challenging for CFD; e.g. DNS has been used for streamwise growth. With suction, grid resources are consumed by the hole and this makes DNS even more expensive. Limited DNS results so far indicate that the vortices which emanate from suction holes appear to be stable. The spanwise clumping observed in the experiment is evidence of a secondary instability that could be associated with suction vortices. A typical porous surface for LFC consists of 0.002 inch diameter holes with 0.020 inch grid spacing L, which is too small to resolve disturbances. A 20:1 scale porous test surface has been machined for improved spatial resolution while the L/d is still representative of flight conditions. Designers of porous surfaces use Goldsmith's criterion to minimize crossstream interaction. However nothing is known about the streamwise interactions. Results using two holes, aligned but displaced in the streamwise direction, indicate that partial TS wave cancellation is possible, depending on the hole spacing and disturbance frequency. Using DNS for streamwise interaction studies will be prohibitively expensive if linear superposition cannot be used for the multiple holes.

Watmuff, Jonathan H.↗
NASA NTRS1994

Structure-property relationships in addition polyimides. 1: Resins from four-ring aromatic diamines containing carbonyl and methylene groups

In an effort to improve the processing characteristics of addition-type polyimide resins the use of flexibilized four-ring aromatic diamine moieties was investigated. A series of 12 diamines containing carbonyl and methylene, as well as oxo and thio bridging groups, was synthesized. The diamines were polymerized with the dimethyl ester of 3.3', 4.4' - benzophenonetetracarboxylic acid (BTDE), using the monomethyl ester of nadic acid (NE) as an end-cap. The effect of diamine structure on the solubility and rheological properties during cure was determined. This paper also describes the effect of diamine structure and formulated molecular weight on the glass transition temperature and thermo-oxidative stability at elevated temperatures after various post-cure regimes. The results indicate that polyimides from some of the diamines containing methylene connecting groups have potential as matrix resins for long-term applications at temperatures up to 300 C.

Delvigs, Peter↗
NASA NTRS2001

Addition Polyimides from Non-Mutagenic Diamines

Studies were conducted to find an acceptable non-mutagenic diamine to replace 4,4'-methylenedianiline (MDA), a suspect carcinogen, which is currently being used in PMR-15 polyimide applications. Several diamines containing fluorine and trifluoromethyl substituent groups were synthesized. The diamines were polymerized with the dimethyl ester of 3,3',4,4'-benzophenone tetracarboxylic acid (BTDE), using the monomethyl ester of nadic acid (NE) as an endcap. The effect of diamine structure on rheological properties, glass transition temperature, and thermo-oxidative stability was investigated. Unidirectional laminates were fabricated from selected resins, using carbon fiber as the reinforcement. The results indicate that some of the diamines containing trifluoromethyl groups are non-mutagenic, and have potential to replace MDA in PMR polyimides for long-term applications at temperatures up to 300 C.

Delvigs, Peter↗
NASA NTRS2007

Effects of Nose Bluntness on Stability of Hypersonic Boundary Layers over Blunt Cone

Receptivity and stability of hypersonic boundary layers are numerically investigated for boundary layer flows over a 5-degree straight cone at a free-stream Mach number of 6.0. To compute the shock and the interaction of shock with the instability waves, we solve the Navier-Stokes equations in axisymmetric coordinates. The governing equations are solved using the 5th-order accurate weighted essentially non-oscillatory (WENO) scheme for space discretization and using third-order total-variation-diminishing (TVD) Runge-Kutta scheme for time integration. After the mean flow field is computed, disturbances are introduced at the upstream end of the computational domain. Generation of instability waves from leading edge region and receptivity of boundary layer to slow acoustic waves are investigated. Computations are performed for a cone with nose radii of 0.001, 0.05 and 0.10 inches that give Reynolds numbers based on the nose radii ranging from 650 to 130,000. The linear stability results showed that the bluntness has a strong stabilizing effect on the stability of axisymmetric boundary layers. The transition Reynolds number for a cone with the nose Reynolds number of 65,000 is increased by a factor of 1.82 compared to that for a sharp cone. The receptivity coefficient for a sharp cone is about 4.23 and it is very small, approx.10(exp -3), for large bluntness.

Kara, K.↗
NASA NTRS2014

Delay of Transition Using Forced Damping

Several experiments which have reported a delay of transition are analyzed in terms of the frequencies of the induced disturbances generated by different flow control elements. Two of the experiments employed passive stabilizers in the boundary layer, one leading-edge bluntness, and one employed an active spark discharge in the boundary layer. It is found that the frequencies generated by the various elements lie in the damping region of the associated stability curve. It is concluded that the creation of strong disturbances in the damping region stabilizes the boundary-layer and delays the transition from laminar to turbulent flow.

Exton, Reginald J.↗
NASA NTRS2010

Kepler Instrument Performance: An In-Flight Update

The Kepler Mission is designed to detect the 80 parts per million (ppm) signal from an Earth-Sun equivalent transit. Such precision requires superb instrument stability on time scales up to 2 days and systematic error removal to better than 20 ppm. The sole scientic instrument is the Photometer, a 0.95 m aperture Schmidt telescope that feeds the 94.6 million pixel CCD detector array, which contains both Science and Fine Guidance Sensor (FGS) CCDs. Since Kepler's launch in March 2009, we have been using the commissioning and science operations data to characterize the instrument and monitor its performance. We find that the in-flight detector properties of the focal plane, including bias levels, read noise, gain, linearity, saturation, FGS to Science crosstalk,and video crosstalk between Science CCDs, are essentially unchanged from their pre-launch values. Kepler'sunprecedented sensitivity and stability in space have allowed us to measure both short- and long- term effects from cosmic rays, see interactions of previously known image artifacts with starlight, and uncover several unexpected systematics that affect photometric precision. Based on these results, we expect to attain Kepler's planned photometric precision over 90% of the field of view.

CCD↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗
NASA NTRS1991

Linear ion trap based atomic frequency standard

In order to develop a trapped ion-based fieldable frequency standard with stability 1 x 10 to the -13th/sq rt tau for averaging times tau greater than 10,000 s, a hybrid RF/DC linear ion trap was developed which permits storage of large numbers of ions with reduced susceptibility to the second-order Doppler effect caused by the RF confining fields. The authors have confined Hg-199(+) ions in this trap and have measured very high Q transitions with good SNRs. In preliminary measurements they obtained stabilities of 1.6 x 10 to the -13th/sq rt tau (tau between 50 and 800 s) with a 160-mHz wide atomic resonance linewidth and a signal-to-noise ratio of 40 for each measurement cycle. Atomic resonance lines as narrow as 30 mHz on the 40.5-GHz clock transition have been measured with no appreciable reduction in the ion signal. A stability of 7 x 10 to the -14th/sq rt tau is made possible by the signal-to-noise and line Q of this measured transition. Analysis of fundamental sources of frequency instability indicates that a long-term stability of 2 x 10 to the -16th is feasible for this device with existing technology for tau = 10 to the 6th s or more.

Prestage, John D.↗
NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analysis were performed to identify the mechanisms by which two-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for two boundary layer transition trip configurations: one is a two-dimensional rectangular-shaped rod and the other is a three-dimensional zigzag tape. Reynolds numbers based on the trip heights are 683 and 300 for the two-and three-dimensional trips, respectively. Simulations with the two-dimensional trip showed that the flow separates at the top of the trip and forms a long recirculation zone downstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff1 experiment.

Transition↗
NASA NTRS2018

Nonlinear Evolution and Breakdown of Azimuthally Compact Crossflow Vortex Pattern over a Yawed Cone

Hypersonic boundary-layer flows over a circular cone at moderate angle of incidence can support strong crossflow instability in between the windward and leeward rays on the plane of symmetry. Due to the more efficient excitation of stationary crossflow vortices by surface roughness, a possible path to transition in such flows corresponds to rapid amplification of the high-frequency secondary instabilities of finite amplitude stationary crossflow vortices. In the present paper, the previous analyses of crossflow instability over a 7- degree half-angle, yawed circular cone in a Mach 6 free stream have been extended to the nonlinear evolution of azimuthally localized crossflow vortex packets and the amplification characteristics and nonlinear breakdown of high-frequency secondary instabilities associated with those packets. A comparison between plane marching PSE and direct Navier-Stokes simulations (DNS) reveals favorable agreement in regard to mode shapes, most amplified disturbance frequencies, and N-factor evolution. In contrast, the quasi-parallel predictions are found to result in severe underprediction of the N-factors. The direct numerical simulations also indicate that the breakdown of secondary instabilities in a 3D hypersonic boundary layer shares certain common features with the previous computations of crossflow transition over subsonic swept wings.

Vortex structure↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗
NASA NTRSDate not supplied

Long Term Performance Stability of TES Detectors

We are developing superconducting transition-edge sensor (TES) microcalorimeter arrays for a variety of applications such as ground-based laboratory astrophysics experiments and next generation space-based X-ray missions. These detectors can provide X-ray spectral information with an unprecedent resolution of ~2 eV at 6 keV and have been selected for the X-ray Integral Field Unit (X-IFU) instrument of ESA’s large flagship mission Athena. To maintain detector performance over the lifetime of the mission, it is important to understand whether environmental conditions that the detector may be exposed to will affect its properties over time. This “aging” begins right after the array leaves the fabrication environment, with potential exposure to humidity, oxygen, or elevated temperatures which may affect the detector performance. In a few prior arrays we have observed increased fall times in the pulse shape and/or the introduction of anomalous low energy tails on the X-ray spectrum. This is thought to be an indication of “aging” on chips exposed to such conditions, causing e.g. changes in the absorber properties. In this contribution, we report on a systematic characterization of TES properties, before and after exposing the chip to various controlled temperature and humidity levels and assess the changes in the measured transition and pulse shapes, energy resolution, and spectral redistribution.

S Beaumont↗
NASA NTRS1959

Flight Investigation of the Stability and Control Characteristics of a 1/4-Scale Model of a Tilt-Wing Vertical-Take-Off-and-Landing Aircraft

An experimental investigation has been conducted to determine the dynamic stability and control characteristics of a tilt-wing vertical-take-off-and-landing aircraft with the use of a remotely controlled 1/4-scale free-flight model. The model had two propellers with hinged (flapping) blades mounted on the wing which could be tilted up to an incidence angle of nearly 90 deg for vertical take-off and landing. The investigation consisted of hovering flights in still air, vertical take-offs and landings, and slow constant-altitude transitions from hovering to forward flight. The stability and control characteristics of the model were generally satisfactory except for the following characteristics. In hovering flight, the model had an unstable pitching oscillation of relatively long period which the pilots were able to control without artificial stabilization but which could not be considered entirely satisfactory. At very low speeds and angles of wing incidence on the order of 70 deg, the model experienced large nose-up pitching moments which severely limited the allowable center-of-gravity range.

Tosti, Louis P.↗
NASA NTRSDate not supplied

Computational Study of Low-Speed Boundary-Layer Laminar-Turbulent Transition over a 30º Swept Plate in a Channel

Reliable boundary-layer laminar-turbulent transition predictions are critical for the design of aircraft that use natural or controlled laminar flow to achieve low drag and better fuel efficiency. During cruise flight through low turbulence, the three-dimensional boundary layer over swept surfaces can transition prematurely due to stationary crossflow instabilities induced by surface roughness. Parabolized stability equations analyses have been successfully used to explain the different phases of the transition process under well controlled perturbations such as steps or discrete roughness elements. However, methodologies are still lacking to model the boundary layer receptivity to distributed random roughness, and the following non-linear instability stages leading to transition. For engineering applications, several semi-empirical methods based on linear amplification factors or local helicity have found growing adoption, but their reliability is limited by their level of simplification and the sparsity of data they are based on. To address this gap, a new study of the effect of distributed random surface roughness on crossflow transition was started, using a 30◦ swept plate as a test vehicle. The plate, which is mounted in the 2 Foot × 3 Foot Low-Speed Boundary-Layer Channel at the NASA Langley Research Center, has been tested with micro-scale roughness of varied geometry near the leading edge. In order to analyze the flow in the test section and prepare Direct Numerical Simulations with resolved roughness, Reynolds-Averaged Navier-Stokes (RANS) simulations of the flow over the plate installed in the wind tunnel test section were performed using the Langtry-Menter transition model with stationary crossflow extension. This paper presents the results of these simulations, with comparison to the experiment.

ARMD↗
NASA NTRS1990

On the stability of swept wing laminar boundary layers including curvature effects

A linear stability analysis that encompasses curvature effects has been conducted in wind tunnel experiments on a swept NACA 64(2)-A015 wing, and published transition-onset results have been correlated with computed N-factor values. A strong stabilizing influence is noted upon the growth of the crossflow disturbance, when the flow is accelerated in regions of high body curvature. The maximum amplified crossflow disturbances were in all cases travelling waves; when TS waves reached their maximum, the N-factors at transition lay in the 9.9-13.8 range. Stabilization due to curvature effects was less pronounced in cases where acceleration occurred over a large portion of chord.

Viken, J.↗
NASA NTRS1992

A high-performance Hg(+) trapped ion frequency standard

A high-performance frequency standard based on (199)Hg(+) ions confined in a hybrid radio frequency (RF)/dc linear ion trap is demonstrated. This trap permits storage of large numbers of ions with reduced susceptibility to the second-order Doppler effect caused by the RF confining fields. A 160-mHz-wide atomic resonance line for the 40.5-GHz clock transition is used to steer the output of a 5-mHz crystal oscillator to obtain a stability of 2 x 10(exp -15) for 24,000-second averaging times. Measurements with a 37-mHz line width for the Hg(+) clock transition demonstrate that the inherent stability for this frequency standard is better than 1 x 10(exp -15) at 10,000-second averaging times.

Prestage, J. D.↗
NASA NTRS2023

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally,Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗
NASA NTRS2023

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally, Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗