Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Does feroxyhyte occur on the surface of Mars

The physical, chemical and paragenetic properties of delta-FeOOH in the form of the mineral feroxyhyte are discussed in relation to the possible composition of the red-brown surface coating of Mars. It is pointed out that the deep-brown ferromagnetic FeOOH polymorph will adhere to magnets such as those on the Viking Lander at Mars ambient temperatures and exhibits spectral maxima in the range 2.95-3.4 m similar to those observed in remote sensing spectra of Mars. The redox properties of the formation of feroxyhyte are shown to be compatible with postulated processes on the Martian surface, and with the results of some of the Viking biological experiments. It is thus concluded that feroxyhyte has the magnetic, chemisorption, spectral, redox and paragenetic properties to suggest its consideration as a possible component of the Martian surface.

Burns, R. G.↗
NASA NTRS1970

Test and Evaluation of the Surveyor 3 Television Camera Returned from the Moon by Apollo 12

Results are presented of engineering tests of the Surveyor III television camera, which resided on the moon for 2 and 1/2 years before being brought back to earth by the Apollo XII astronauts. Electric circuits, electrical, mechanical, and optical components and subsystems, the vidicon tube, and a variety of internal materials and surface coatings were examined to determine the effects of lunar exposure. Anomalies and failures uncovered were analyzed. For the most part, the camera parts withstood the extreme environment exceedingly well except where degradation of obsolete parts or suspect components had been anticipated. No significant evidence of cold welding was observed, and the anomalies were largely attributable to causes other than lunar exposure. Very little evidence of micrometeoroid impact was noted. Discoloration of material surfaces -- one of the major effects noted--was found to be due to lunar dust contamination and radiation damage. The extensive test data contained in this report are supplemented by results of tests of other Surveyor parts retrieved by the Apollo XII astronauts, which are contained in a companion report.

Source record↗
NASA NTRS1992

Morphology and composition of condensates on Apollo 17 orange and black glass

Lunar soil sample 74220 and core samples 74001/2 consist mainly of orange glass droplets, droplet fragments, and their crystallized equivalents. These samples are now generally accepted to be pyroclastic ejecta from early lunar volcanic eruptions. It has been known since early examination of these samples that they contain surface coatings and material rich in volatile condensible phases, including S, Zn, F, Cl, and many volatile metals. The volatiles associated with these orange and black glasses (and the Apollo 15 green glasses) may provide important clues in understanding the differentiation and volcanic history of the Moon. In addition, condensible volatiles can be mobilized and concentrated by volcanic processes. We have reviewed many of our existing photomicrographs and energy dispersive analysis (EDXA) of grain surfaces and have reexamined some of our older SEM mounts using an improved EDXA system capable of light-element detection and analysis (oxygen, nitrogen, and carbon). The results from these investigations are presented.

Mckay, David S.↗
DOE OSTI2020

Multi-hydrophilic functional network enables porous membranes excellent anti-fouling performance for highly efficient water remediation

Membrane technology is believed as a cost-effective approach for solving the water issues, where as it suffers from serious membrane fouling. Surface grafting and surface coating have been proved to be effective in abating the membrane fouling; however, these processes always need additional procedures and compromise the initial permeance of the membranes. Herein, we developed a kind of highly permeable polyacrylonitrile (PAN) membranes with excellent anti-fouling performance through one-step phase inversion of the PAN casting solution containing water-soluble active additives. During the process, the water-soluble active additives could segregate towards the membrane surface and pore walls; thereby finely tailoring the pore structures of the PAN-based membranes. Moreover, the active additives could react with each other to form crosslinked networks containing multi-hydrophilic functional groups including CH2-O-CH2, -OH or-Si-OH. Consequently, the PAN-based membranes exhibited surprising superhydrophilicity with water contact angle below 10. even after soaking in water for one week and the anti-fouling permeance of the membranes increased significantly with permeance recovery rate above 93%. Interestingly, the modified membranes also demonstrated both high permeances and high separation efficiency, thereby showing strong promise in water environmental remediation including wastewater treatment and oil/water emulsion separation.

Anti-fouling↗
NASA NTRS2011

A High-Resolution Measurement of Ball IR Black Paint's Low-Temperature Emissivity

High-emissivity paints are commonly used on thermal control system components. The total hemispheric emissivity values of such paints are typically high (nearly 1) at temperatures above about 100 Kelvin, but they drop off steeply at lower temperatures. A precise knowledge of this temperature-dependence is critical to designing passively-cooled components with low operating temperatures. Notable examples are the coatings on thermal radiators used to cool space-flight instruments to temperatures below 40 Kelvin. Past measurements of low-temperature paint emissivity have been challenging, often requiring large thermal chambers and typically producing data with high uncertainties below about 100 Kelvin. We describe a relatively inexpensive method of performing high-resolution emissivity measurements in a small cryostat. We present the results of such a measurement on Ball InfraRed BlackTM(BIRBTM), a proprietary surface coating produced by Ball Aerospace and Technologies Corp (BATC), which is used in spaceflight applications. We also describe a thermal model used in the error analysis.

Tuttle, Jim↗
DOE OSTI2020

Roll-To-Roll Atomic Layer Deposition of Titania Nanocoating on Thermally Stabilizing Lithium Nickel Cobalt Manganese Oxide Cathodes for Lithium Ion Batteries

Conformal coating of ceramic layers (nm-thick) on Ni-rich layered cathode materials is an effective strategy for improving high-temperature longevity of Li-ion batteries (LIBs). In this work, we develop a roll-to-roll atomic layer deposition (R2R ALD) apparatus for growing uniform nanolayers of TiO 2 . We explore the effect of ALD parameters (temperature: 120–180 °C and line speed: 2–40 mm s –1 ) on the TiO 2 surface coating and subsequently investigate the electrochemical performance of the as-prepared cathodes. The capacity retention of TiO 2 -coated porous electrodes is substantially improved compared to that of the pristine cathode material for high-temperature cycling. Electrochemical impedance spectroscopy confirms that the ALD-TiO 2 coating suppresses the undesired side reactions initiated at the electrode/electrolyte interface, reduces charge transfer resistance, and ultimately facilitates the Li + transport through the composite cathode nanostructure. The robust design of the ALD-TiO 2 cathode material enables high-temperature operation (>55 °C) with enhanced specific capacity, superior rate capability, excellent cyclability, and ultra-high coulombic efficiency within a wide potential window (3.0–4.35 V). Furthermore, the R2R ALD technique developed in this work paves the way for large-scale fabrication of ceramic-coated cathode sheets with a production rate reaching 2.4 m min –1 for a continuous coating operation.

25 ENERGY STORAGE↗
DOE OSTI2021

DEVELOPMENT OF STABLE ANODE AND CATHODE MATERIALS FOR RECHARGEABLE BATTERIES

Batteries have been employed in a variety of applications, such as portable electronics, electric vehicles (EVs), and stationary energy storage to preserve energy from other renewable sources (like wind or solar energy). The ultimate goal is to develop high energy density, long life span, better safety, and low cost of the batteries. However, current commercialized batteries (like lead-acid, zinc-alkaline, lithium-ion batteries (LIBs)) could not fulfill all the demands of diversified applications. LIBs predominate the market because of their high energy density. To achieve a higher capacity of the cell, high-nickel layered (Ni > 90%) cathode materials are promising candidates since they compose high specific capacity and discharge voltage. In chapter 1, an introduction to cell energy density and the development of high-nickel layered cathode materials along with associated obstacles of poor cycling stability and thermal stability have been discussed. Associated works like doping or surface coating have also been mentioned in this section. In chapter 2, Al doping in high-nickel layered cathode materials to enhance the structural and thermal stability was introduced. Uniform incorporation of Al doping is achieved by mechanical fusion and calcination processes. The Al doping not only decreased the Li/Ni mixing ratio but also enhance the thermal resistance to oxygen evolution because of strong Al-O bonding, which leads to elevated electrochemical and thermal stability. In chapter 3, TiN is implemented as a Ti dopant for high-nickel layered cathode materials to improve the electrochemical performance in the LIBs. The Ti not only diffused within the bulk structure but also formed segregation on the surface, which improved the structural stability and led to better cycling performance. Although LIBs deliver high energy density, safety concerns of flammable organic electrolytes have not been resolved yet. Therefore, the aqueous rechargeable zinc-ion batteries (ZIB) have been praised for their safe, low-cost, eco-friendly stationary energy storage, which is considered as a complementary system to LIBs. In chapter 4, the mechanism, advantages, and challenges of ZIBs would be given and the strategies for solving the zinc metal anode issues have been discussed in this section. In chapter 5, a polymer coating method was reported to facilitate Zn deposition/ stripping by coordination with Zn2+ and prevented direct contact with aqueous electrolyte to block corrosion side-reactions. With this coating, a boost in a lifetime (up to 400 hours) and lower polarization under extremely high current conditions (10 mA cm-2) have been achieved in repeated Zn deposition/ stripping cycling.

25 ENERGY STORAGE↗
NASA NTRS1990

Aeolian Removal of Dust Types from Photovoltaic Surfaces on Mars

Dust elevated in local or global dust storms on the Martian surface could settle on photovoltaic (PV) surfaces and seriously hamper their performance. Using a recently developed technique to apply a uniform dust layer, PV surface materials were subjected to simulated Martian winds in an attempt to determine whether natural aeolian processes on Mars would sweep off the settled dust. Three different types of dust were used. The effects of wind velocity, angle of attack, height above the Martian surface, and surface coating material were investigated. It was found that arrays mounted on an angle of attack approaching 45 deg show the most efficient clearing. Although the angular dependence is not sharp, horizontally mounted arrays required much higher wind velocities to clear off the dust. From this test it appears that the arrays may be erected quite near the ground, but previous studies have suggested that saltation effects can be expected to cause such arrays to be covered by soil if they are set up less than about a meter from the ground. Particle size effect appear to dominate over surface chemistry in these experiments, but additional tests are required to confirm this.

Gaier, James R.↗
DOE OSTI2024

The Key Role of Grain Boundary Dynamics in Revolutionizing the Potential of Solid Electrolytes

Solid electrolytes (SEs) have the potential to enhance the safety and performance of Li-metal batteries. However, the existence of grain boundaries in polycrystalline SEs presents a significant challenge for both ionic and electronic migration, promoting the propagation of detrimental lithium dendrites. This study compares the roles of grain boundaries in electrical properties of three distinct SEs including garnet-type Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 (LLZO), argyrodite-type Li 6 PS 5 Cl (LPSC), and NASICON-type Li 1+x+y Al x (Ti,Ge) 2-x Si y P 3-y O 12 (LATP). Results demonstrate that the electronic and ionic conductivities of solid-state electrolytes are affected differently by grain boundaries, depending on the specific type of electrolyte. For instance, LLZO and LATP experience dielectric breakdown at 3.7 and 5.3 V, respectively, while LPSC does not exhibit such behavior. Here, a new chemical modification is proposed that simultaneously alters the composition of both the surface and grain boundaries of SEs, ultimately reducing electronic conductivity for the LLZO SEs. Consequently, the proposed LLZO exhibits unprecedented dendrite-free cycling stability, achieving a remarkable 12 000-h lifetime at room temperature, surpassing conventional strategies such as surface coatings in dendrite mitigation. This study highlights the significance of modifying grain boundaries to design safe and durable Li-metal batteries. It provides new insights for developing SEs that are highly resistant to dendrite formation.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Preliminary Evaluation of Polyarylate Dielectric Films for Cryogenic Applications

Polymeric materials are used extensively on spacecraft and satellites in electrical power and distribution systems, as thermal blankets and optical surface coatings, as well as mechanical support structures. The reliability of these systems when exposed to the harsh environment of space is very critical to the success of the mission and the safety of the crew in manned-flight ventures. In this work, polyarylate films were evaluated for potential use as capacitor dielectrics and wiring insulation for cryogenic applications. Two grades of the film were characterized in terms of their electrical and mechanical properties before and after exposure to liquid nitrogen (-196 C). The electrical characterization consisted of capacitance and dielectric loss measure Cents in the frequency range of 50 Hz to 100 kHz, and volume and surface resistivities. The mechanical measurements performed included changes in tensile (Young's modulus, elongation-at-break, and tensile strength) and structural properties (dimensional change, weight, and surface morphology). The preliminary results, which indicate good stability of the polymer after exposure to liquid nitrogen, are presented and discussed.

Patterson, Richard L.↗
DOE OSTI2025

Compatibility of molten plutonium with wrought and additively manufactured metal crucibles

Understanding plutonium’s interaction with metals is crucial for optimizing pyrochemical operations, nuclear fuel containment, and various actinide processing techniques. Traditionally, tantalum crucibles are employed for plutonium processing due to their high durability, excellent temperature stability, and low solubility in plutonium. However, tantalum faces challenges such as plutonium wetting and diffusion, making surface coatings particularly important for crucibles in pyrochemical applications to enhance corrosion resistance against plutonium. Tantalum is also expensive and difficult to machine, prompting the need for advanced manufacturing techniques to address these challenges. Here, in this work, we investigate the interaction of Pu with tantalum and titanium crucibles fabricated using both traditional machining methods and laser powder bed fusion (LPBF) additive manufacturing (AM). LPBF-AM is an advanced technique that allows for the creation of complex geometries from traditionally difficult-to-machine metals by using a high-powered laser to build parts. Previous studies of conventional manufactured tantalum have utilized oxidation and carburization of the surface to mitigate plutonium wetting; however, no studies of surface modified LPBF-AM material have been undertaken. These studies are crucial, given the typical differences in the grain structure between conventional and LPBF-AM materials. All crucibles underwent differential scanning calorimetry to confirm the melting of plutonium. Subsequently, the crucibles were sectioned and mounted in epoxy for microstructural analysis using optical microscopy and scanning electron microscopy. This investigation, comparing the performance of wrought vs AM metal crucibles, provides a basis for future tooling applications in actinide processing techniques and can address the challenges associated with traditional machining, particularly in pyrochemical applications.

Actinides↗
NASA NTRS2019

Durability of YSZ Coated Ti2AlC in 1300°C Mach 0.3 Burner Rig Tests

A thermal barrier coating system survived burner rig testing at 1300°C for 500 h. A 160 µm thick YSZ coating was applied to a Ti2AlC MAX phase sample by PS-PVD and tested face-on in an atmospheric Mach 0.3 jet fuel burner, using 5-h thermal cycles. No TBC spallation or recession was observed, only a 2.4 mg/sq. cm mass gain. The modest weight gain precluded severe volatility losses under high velocity burner conditions. The coating surface exhibited colonies of (111) flourite fiber-textured columns separated by craze patterns, with no visible moisture attack. The metastable tetragonal t' YSZ phase was obtained initially, transitioning to teq and cubic YSZ, but with little detrimental monoclinic. The thickness of the alumina TGO was ~21-23 m under the heated YSZ face and ~13-15 m on the uncoated, cooler backside. The backside exhibited removal of initial transient TiO2 nodules and etching of the underlying Al2O3 scale by volatile hydroxides in high temperature, high velocity water vapor. Aerodynamic forces produced some bending of the cantilevered sample due to creep. The test indicated exceptional stability of YSZ coatings on Ti2AlC under turbine conditions.

Smialek, J.↗
DOE OSTI2020

Simultaneous transmission/absorption photometry of particle-laden filters from wildland fires during the Biomass Burning Observation Project (BBOP) field campaign

Transmissivity and absorptivity measurements were carried out simultaneously in the visible (wavelength of 532 nm) at laboratory conditions using particle-laden filters obtained from a three-wavelength particle/soot absorption photometer (PSAP). Here, the particles were collected on filters from wildland fires over the Pacific Northwest during the Department of Energy Biomass Burning Observation Project (BBOP) field campaign in 2013. The objective of this investigation was to apply this measurement approach, referred to as simultaneous transmission/absorption photometry (STAP), to estimate the aerosol extinction coefficient from actual field-campaign filter aerosol, and compare results with the PSAP. The STAP approach offers several advantages over the PSAP, including estimation of the extinction coefficient from temperature measurements (avoiding the complexities associated with filter reflectivity/scattering measurements), as well as determination of the filter optical properties and filter effects on particle absorption (resulting in particle absorption enhancement). The experimental arrangement included a laser probe beam impinging normal to the particle-coated surface of a vertically mounted filter, and a thermocouple placed flush in the middle of (and in thermal contact with) the filter uncoated back surface. With this simple arrangement, the transmissivity and absorptivity were determined simultaneously at a given laser beam wavelength. The measurement repeatability was better than 0.3 K (95% confidence level) for temperature and 0.4 mW for laser power. The limit of detection for the extinction coefficient was estimated to be (8–12) Mm -1 (95% confidence level) at about 1.9 mW laser power. The extinction coefficient was determined through measurement of both PSAP blank and exposed filters. Filters were obtained from nine different aircraft flights conducted during the BBOP campaign, representing different flight patterns, days, stages of burning, landscapes, and wildland fires. The STAP extinction coefficient matched the darkness of the filter coating, however the PSAP-filter results did not follow the same order. Although there were differences in transmissivity between the two techniques, the estimated values for absorption coefficient were in good agreement.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1999

Fabrication system, method and apparatus for microelectromechanical devices

A fabrication system and method of fabrication for producing microelectromechanical devices such as field-effect displays using thin-film technology. A spacer is carried at its proximal end on the surface of a substrate having field-effect emitters with the spacer being enabled for tilting movement from a nested position to a deployed position which is orthogonal to the plane of the substrate. An actuator is formed with one end connected with the substrate and another end connected with spacer. The actuator is made of a shape memory alloy material which contracts when heated through the material's phase-change transition temperature. Contraction of the actuator exerts a pulling force on the spacer which is tilted to the deployed position. A plurality of the spacers are distributed over the area of the display. A glass plate having a phosphor-coated surface is fitted over the distal ends of the deployed spacer.

Johnson, A. David↗
DOE OSTI2025

Effects of oxidation and impurities in lithium surfaces on the emitting wall plasma sheath

The use of lithium as a surface coating in fusion devices improves the plasma performance, but the change in the wall properties affects the secondary electron emission properties of the material. Lithium oxidizes easily, which drives the emission yield well above unity. We present here simulations demonstrating the change in the sheath structure from monotonic to the nonmonotonic space-charge limited sheath using an energy-dependent data-driven emission model, which self-consistently captures both secondary emission and backscattering populations. Increased secondary electron emission from the material has ramifications for the degradation and erosion of the wall. The results show that the oxidation leads to an increased electron energy flux into the wall and a reduced ion energy flux. The net transfer of energy to the surface is significantly greater for the oxidized case than for the pure lithium case. High backscattering rates of low-energy particles lead to a high re-emission rate at the wall.

Fusion reactors↗
DOE OSTI2026

Mechanistic insights into low-temperature oxidation of carbon fibers: Influence of hydrogen defects and crystallite size

Although oxidation mechanisms have been exhaustively studied for graphite, similar analyses of carbon fibers are comparatively sparse. Most prior work has focused on quantifying weight loss or assessing protective surface coatings designed to slow oxidation. The use of optical spectroscopic techniques for oxidation analyses is comparatively unexplored, but such techniques could provide an early indicator of fiber oxidation that would undermine carbon fiber performance. Here, in this work, we applied Raman spectroscopy to study oxidation-induced spectral alterations in 16 carbon fiber types from 7 manufacturers oxidized at 300 °C for 72 h, 400 °C for 8 h, and 500 °C for 1 h. We connect these results with structural properties of the carbon fibers obtained through wide-angle X-ray scattering, identifying a linear dependence between the reactivity of carbon fibers and the crystallite size of the unperturbed fibers. We then demonstrate that substituted hydrogen defects are likely removed from the fiber surface during oxidation and use the relative defect concentration to predict the Raman spectral change as a function of temperature and time, assuming Arrhenius behavior.

Carbon fiber↗
NASA NTRS2024

Additively Manufactured Plastic Plasma Spectrometer

We report results in development and testing of a low resource top hat electrostatic analyzer (ESA) for space plasma measurements. This device has been additively manufactured (3D-printed) using fused deposition modeling. The classic top hat design is composed of four plastic pieces, without any surface coatings. The three conducting electrodes are printed from carbon nanotube infused polyether ether ketone (CNT-PEEK). The fourth piece, an insulating electrode support, uses pure PEEK. This ESA is designed to detect electrons in space from 10eV up to 30 keV. We demonstrate that the printed CNT-PEEK is sufficiently electrically conductive to support the fast high voltage slewing often required for high time resolution measurements. The plastic ESA has been successfully vibrated beyond standard pre-flight levels, tested under keV electron beam illumination over a wide range of temperatures, and tested under UV illumination, simulating the solar Ly-α flux. In comparison with an identical machined aluminum ESA, our CNT-PEEK ESA provides nominal energy/angle band passes, closely matching simulation. These band passes imply minimal impact from surface charging at beam energies of 2-3 keV, although more investigation is needed. We also find that the CNT-PEEK ESA provides far superior out-of-band electron rejection and UV photon rejection compared to the machined aluminum ESA. We do not detect any problems with trapped gases or outgassing. This development offers potential for significant mass savings, implementation of otherwise unattainable geometric configurations, and dramatic simplification in manufacturing and assembly processes required for development of space plasma instruments.

Quetzal Larrick↗
NASA NTRS1987

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Tests were performed in a transient heat transfer tunnel in which the model under test was preheated prior to allowing room temperature air to be suddenly drawn over the model. The resulting movement of isothermal contours on the model is revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record is obtained of a temperature and time data pair for all points on the model during a single test. Experiments on a duct model are reported in which the model was preheated using a hot air stream. A manner in which initial model temperature nonuniformities could be taken into account was investigated. The duct model was also tested with a steady-state measurement technique and results were compared with the transient measurements, but recognizing that differences existed between the upstream thermal boundary conditions. The steady-state and transient measurements were shown to be consistent with predicted values. The main advantage of this transient heat transfer technique using liquid crystals is that since the test model need not be actively heated, high-resolution measurements on surfaces with complex shapes may be obtained.

Jones, T. V.↗