Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

A Preliminary Investigation of a New Method for Testing Aerofoils in Free Flight

This report is a description of a new method of testing aerofoils in free flight devised by the National Advisory Committee for Aeronautics. The method consists in lowering below a flying airplane a large inverted aerofoil on three small steel wires in such a way that the lift on the aerofoil always keeps the wires tight. The resultant force is measured by the tension in the wires, and the direction of the resultant by the amount the wing trails backwards. A test was made on an aerofoil of the N.A.C.A. #64 section, 6 ft. in span and the results are compared with a similar section tested in the wind tunnel. This investigation indicates that by the use of suitable recording apparatus aerofoils may be accurately and conveniently tested at a Reynolds number, a velocity and a degree of turbulence, comparable with that on the full-sized airplane. Satisfactory experiments were also made in trailing a sphere and a streamlined body on single wires.

Norton, F H↗
NASA NTRS1969

Electronic analog equalization for vibrational testing

Method of real time equalization involving use of an analog computer achieves effective qualification testing by realistically simulating the effects of the vibrational forces which will actually be experienced in powered flight.

Trubert, M. R. P.↗
NASA NTRS1972

Testing for hydrogen embrittlement: Primary and secondary influences

An overview is presented of the hydrogen embrittlement process, both internal as well as external, to make more clear the type of parameters which must be considered in the selection of a test method and test procedure, so that the resulting data may be meaningfully applied to real engineering structures. Three primary influences on the embrittlement process are considered: (1) the original location and form of the hydrogen, (2) the transport reactions involved in the transport of hydrogen from its origin to some point where it can interact with the metal to cause embrittlement, and (3) the embrittlement interaction itself. A few secondary influences on the embrittlement process are also discussed.

Nelson, H. G.↗
NASA NTRS1974

Testing for hydrogen environment embrittlement - Primary and secondary influences

A somewhat phenomological overview of the hydrogen embrittlement process, both internal as well as external, is presented in a effort to make more clear the type of parameters which must be considered in the selection of a test method and test procedure so that the resulting data may be meaningfully applied to real engineering structures. What are believed to be the three primary influences on the embrittlement process are considered - the original location and form of the hydrogen, the transport reactions involved in the transport of hydrogen from its origin to some point it can interact with the metal to cause embrittlement, and the embrittlement interaction itself. Additionally, a few of the large number of secondary influences on the embrittlement process are discussed, for example, the influence of impurity species in the environment, surface hydride films, and surface oxide films.

Nelson, H. G.↗
NASA NTRS1975

Laser data transfer flight experiment definition

A set of laser communication flight experiments to be performed between a relay satellite, ground terminals, and space shuttles were synthesized and evaluated. Results include a definition of the space terminals, NASA ground terminals, test methods, and test schedules required to perform the experiments.

Merritt, J. R.↗
NASA NTRS1984

Fracture of composite-adhesive-composite systems

This program was undertaken to initiate the development of a test method for testing adhesive joints in metal-adhesive-composite systems. The uniform double cantilever beam (UDCB) and the width tapered beam (WTB) specimen geometries were evaluated for measuring Mode I fracture toughness in these systems. The WTB specimen is the preferred geometry in spite of the fact that it is more costly to machine than the UDCB specimen. The use of loading tabs attached to thin sheets of composites proved to be experimentally unsatisfactory. Consequently, a new system was developed to load thin sheets of adherends. This system allows for the direct measurement of displacement along the load line. In well made joints separation occurred between the plies rather than in the adhesive.

Ripling, E. J.↗
NASA NTRS1988

Adaptive wall research with two- and three-dimensional models in low speed and transonic tunnels

This paper summarises recent research at the University of Southampton into adaptive wall technology and outlines the direction of current efforts. The work is aimed at developing techniques for use in test sections where the top and bottom walls may be adjusted in single curvature. Wall streamlining eliminates, as far as experimentally possible, the top and bottom wall interference in low speed and transonic aerofoil testing. A streamlining technique has been developed for low speeds which allows the testing of swept wing panels in low interference environments. At higher speeds, a comparison of several two-dimensional transonic streamlining algorithms has been made and a technique for streamlining with a choked test section has also been developed. Three-dimensional work has mainly concentrated on tests of sidewall mounted half-wings and the development of the software packages required to assess interference and to adjust the flexible walls. It has been demonstrated that two-dimensional wall adaptation can significantly modify the level of wall interference around relatively large three-dimensional models. The residual interferences are small and are probably amenable to standard post-test correction methods. Tests on a calibrated wing-body model are planned in the near future to further validate the proposed streamlining technique.

Lewis, M. C.↗
NASA NTRS1995

Standard methods for open hole tension testing of textile composites

Sizing effects have been investigated by comparing the open hole failure strengths of each of the four different braided architectures as a function of specimen thickness, hole diameter, and the ratio of specimen width to hole diameter. The data used to make these comparisons was primarily generated by Boeing. Direct comparisons of Boeing's results were made with experiments conducted at West Virginia University whenever possible. Indirect comparisons were made with test results for other 2-D braids and 3-D weaves tested by Boeing and Lockheed. In general, failure strength was found to decrease with increasing plate thickness, increase with decreasing hole size, and decreasing with decreasing width to diameter ratio. The interpretation of the sensitive to each of these geometrical parameters was complicated by scatter in the test data. For open hole tension testing of textile composites, the use of standard testing practices employed by industry, such as ASTM D5766 - Standard Test Method for Open Hole Tensile Strength of Polymer Matrix Composite Laminates should provide adequate results for material comparisons studies.

Portanova, M. A.↗
NASA NTRS1995

Standard methods for filled hole tension testing of textile composites

The effects of two test specimen geometry parameters, the specimen width and W/D ratio, on filled-hole tensile strength were determined for textile composite materials. Test data generated by Boeing and Lockheed on 2-D and 3-D braids, and 3-D weaves were used to make these evaluations. The investigation indicated that filled-hole tensile-strength showed little sensitivity to either parameter. Test specimen configurations used in open-hole tension tests, such as those suggested by ASTM D5766 - Standard Test Method for Open Hole Tensile Strength of Polymer Matrix Composite Laminates or those proposed by MIL-HDBK-17-lD should provide adequate results for material comparisons studies. Comparisons of the materials' open-hole and filled-hole tensile strengths indicated that the latter were generally lower than the former. The 3-D braids were the exception; their filled-hole strengths were unexpected larger than their open-hole strengths. However, these increases were small compared to the scatter in the data. Thus, filled hole tension may be a critical design consideration for textile composite materials.

Portanova, M. A.↗
NASA NTRS1999

Battery/Ultracapacitor Evaluation for X-38 Crew Return Vehicle (CRV)

This presentation reported on the evaluation of the battery/ultracapacitor for the crew return vehicle (CRV). The CRV, as part of the international space station (ISS) planning, will be available to return to earth an ill or injured crew person, or if the ISS becomes unsafe, and the shuttle is not available. The requirements of the X-38 CRV are reviewed, and in light of the power requirements, the battery's required performance is reviewed. The ultracapacitor bank, and its test method is described. The test results are reviewed. A picture of the test set up is displayed showing the ultracapacitor bank and the NiMH battery. The presentation continues by reviewing tests of 5 available trade high power cell designs: (1) Hawker lead acid, (2) Bolder lead acid, (3) Energizer NiMH, (4) Sanyo NiCd, and (5) Energizer NiCd. The test methods and results are reviewed. There is also a review of the issues concerning lead acid batteries and conclusions.

Darcy, Eric↗
NASA NTRS2000

Predictability of Gaseous Impact Ignition Sensitivity from Autoignition Temperature Data

An analysis of cumulative binomial probabilities for a quantal-type test like ASTM G74 indicates that for a probability of reaction in a single trial of 0.05, the probability of obtaining zero reactions in 20 trials is only approximately 36 percent, Because the lack of precision with the ASTM G74 test logic could be potentially misleading, an investigation was conducted to determine if pneumatic impact sensitivity could be predicted more reliably from other, more precise test methods. Pneumatic impact sensitivity tests were conducted following ASTM G74, but employing more rigorous test logics; autoignition temperature tests were conducted per ASTM G72. Polytetrafluoroethylene (PTFE), Viton A, polyethylene, polyoxymethylene polyamide, and silicone were the polymers used. After a fixed number of pneumatic impact tests was performed at set pressures, a plot of reaction frequency over a 3.4 to 24.1 MPa impact pressure range indicated that PTFE, Viton A, and silicone would outperform other polymers. The 50 percent pneumatic impact reactivity level was determined with the Bruceton test method. The data obtained resulted in a strong correlation between the 50 percent reactivity level and the autoignition temperature of polymers, indicating similar ignition mechanisms.

Hirsh, David↗
NASA NTRS1949

Landing Procedure in Model Ditching Tests of Bf 109

The purpose of the model tests is to clarify the motions in the alighting on water of a land plane. After discussion of the model laws, the test method and test procedure are described. The deceleration-time-diagrams of the landing of a model of the Bf 109 show a high deceleration peek of greater than 20g which can be lowered to 4 to 6g by radiator cowling and brake skid.

Sottorf, W.↗
NASA NTRS2004

A Re-programmable Platform for Dynamic Burn-in Test of Xilinx Virtexll 3000 FPGA for Military and Aerospace Applications

Field Programmable Gate Arrays (FPGA) have played increasingly important roles in military and aerospace applications. Xilinx SRAM-based FPGAs have been extensively used in commercial applications. They have been used less frequently in space flight applications due to their susceptibility to single-event upsets. Reliability of these devices in space applications is a concern that has not been addressed. The objective of this project is to design a fully programmable hardware/software platform that allows (but is not limited to) comprehensive static/dynamic burn-in test of Virtex-II 3000 FPGAs, at speed test and SEU test. Conventional methods test very few discrete AC parameters (primarily switching) of a given integrated circuit. This approach will test any possible configuration of the FPGA and any associated performance parameters. It allows complete or partial re-programming of the FPGA and verification of the program by using read back followed by dynamic test. Designers have full control over which functional elements of the FPGA to stress. They can completely simulate all possible types of configurations/functions. Another benefit of this platform is that it allows collecting information on elevation of the junction temperature as a function of gate utilization, operating frequency and functionality. A software tool has been implemented to demonstrate the various features of the system. The software consists of three major parts: the parallel interface driver, main system procedure and a graphical user interface (GUI).

Field Programmable Gate Arrays (FPGA)↗
NASA NTRS2019

Slow Crack Growth of Boron Nitrides for Electric Propulsion Components

The Deep Space Gateway requires thruster systems to maintain spatial position. One control system being considered involves Hall thrusters. Historically, Hall thruster discharge channels have used several grades of hot-pressed hexagonal boron nitride. This study compliments data presented at ICACC (International Conference and Expo on Advanced Ceramics and Composites) 2018 and investigates the fracture toughness and slow crack growth parameters of several commercially available boron nitride grades including HP, M, M26, and Shapal Hi-M. The prior work revealed that some grades of BN absorb water and change strength thus presenting a philosophical conundrum on crack growth test methods. Advantages of different test methods will be discussed. The grades selected for this study are of interest because their available billet size is sufficient for Hall thruster discharge channels, or because they have heritage in Hall thruster applications. Ultimately, the data will be used to perform material selection, system design and reliability analyses.

Ceramics↗
NASA NTRSDate not supplied

Overview of Space Environmental Effects (SEE) Team Electrostatic Discharge (ESD) Testing

Electrostatic discharge (ESD) due to the radiation environment encountered during spaceflight missions is a serious risk that must be mitigated by careful testing and design considerations. The MSFC Space Environmental Effects (SEE) Team has world-class facilities for ESD testing along with decades of experience. The Team has recently conducted successful campaigns for several high-profile projects including Europa Clipper, Exploration Upper Stage, Lunar Gateway, Orion, Docking System, and Human Landing System. This presentation will give a brief overview of ESD causes, hazards, test methods and test deliverables.

Peter Bertone↗
NASA NTRS1990

Charge transfer efficiency measurements at low signal levels on STIS/SOHO TK1024 CCD's

Charge transfer efficiency (CTE) test methods are reviewed, and the results and conclusions of the tests are given. The test methods have been utilized to describe the CTE characteristics of the Tektronix 1024 by 1024 CCD to optimize low dark current, low readout noise, and high CTE at low signal levels. CTE modelling is described, and three test methods are set forth and compared. The Fe-55 X-ray response method utilizes the response of a CCD to X-ray photons from the radioactive source Fe-55. The extended pixel edge response method employs the measurement of the charge lost to successive pixels by a known initial signal as it is shifted through the array. The charge injection method consists of charge injection through the output amplifier reset transistor. These measurements were performed on several devices with known CTEs. The CTEs are found to be in agreement for the three methods, making application and test requirements the principal criteria for their use.

Orbock, J. D.↗
NASA NTRS1994

Offgassing test methodology for composite materials

A significant increase in the use of composite materials has occurred during the past 20 years. Associated with this increased use is the potential for employees to be exposed to offgassing components from composite systems. Various components in composite systems, particularly residual solvents, offgas under various conditions. The potential for offgassing to occur increases as a composite material is heated either during cure or during lay-up operations. Various techniques can be employed to evaluate the offgassing characteristics of a composite system. A joint effort between AIA and SACMA resulted in the drafting of a proposed test method for evaluating the offgassing potential of composite materials. The purpose of testing composite materials for offgassing is to provide the industrial hygienist with information which can be used to assess the safety of the workplace. This paper outlines the proposed test method and presents round robin testing data associated with the test method. Also in this presentation is a discussion of classes of compounds which require specialized sampling techniques.

Scheer, Dale A.↗
NASA NTRS2016

Elaborated Odor Test for Extended Exposure

Concerns were raised when incidental exposure to a proprietary bonding material revealed the material had an irritating odor. The NASA-STD-6001B document describes a supplemental test method option for programs to evaluate materials with odor concerns (Test 6, Odor Assessment). In addition to the supplemental standard odor assessment with less than 10 seconds of exposure, the NASA White Sands Test Facility (WSTF) Materials Flight Acceptance Testing section was requested to perform an odor test with an extended duration to evaluate effects of an extended exposure and to more closely simulate realistic exposure scenarios. With approval from the NASA Johnson Space Center Industrial Hygienist, WSTF developed a 15-minute odor test method. WSTF performed this extended-duration odor test to evaluate the odor and physical effects of the bonding material configured between two aluminum plates, after the safety of the gas was verified via toxicity analysis per NASA-STD-6001B Test 7, Determination of Offgassed Products. During extended-duration testing, odor panel members were arranged near the test material in a small room with the air handlers and doors closed to minimize dilution. The odor panel members wafted gas toward themselves and recorded their individual assessments of odor and physical effects at various intervals during the 15-minute exposure and posttest. A posttest interview was conducted to obtain further information. Testing was effective in providing data for comparison and selection of an optimal offgassing and odor containment configuration. The developed test method for extended exposure is proposed as a useful tool for further evaluating materials with identified odors of concern if continued use of the material is anticipated.

Buchanan, Vanessa D.↗