SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The potential of zinc orthotitanate as a pigment for spacecraft thermal control was demonstrated. The properties and performance of pigments prepared by solid state, coprecipitation, and mixed oxalate methods were compared. Environmental tests and subsequent spectral analysis were given primary emphasis.
A wicking investigation revealed that passive thermal conditioning was feasible and provided considerable weight advantage over active systems using throttled vent fluid in a Centaur D-1s launch vehicle. Experimental wicking correlations were obtained using empirical revisions to the analytical flow model. Thermal subcoolers were evaluated parametrically as a function of tank pressure and NPSP. Results showed that the RL10 category I engine was the best candidate for boost pump replacement and the option showing the lowest weight penalty employed passively cooled acquisition devices, thermal subcoolers, dry ducts between burns and pumping of subcooler coolant back into the tank. A mixing correlation was identified for sizing the thermodynamic vent system mixer. Worst case mixing requirements were determined by surveying Centaur D-1T, D-1S, IUS, and space tug vehicles. Vent system sizing was based upon worst case requirements. Thermodynamic vent system/mixer weights were determined for each vehicle.
An imaging upconverter has been constructed which is suitable for use in the study of the thermal 10-micron radiation from astronomical sources. The infrared radiation is converted to visible radiation by mixing in a 1-cm-long proustite crystal. The phase-matched 2-kayser bandpass is tunable from 9 to 11 microns. The conversion efficiency is 2 by 10 to the -7th power and the field of view of 40 arc seconds on the sky contains several hundred picture elements, approximately diffraction-limited resolution in a large telescope. The instrument has been used in studies of the sun, moon, Mercury, and VY Canis Majoris.
A computational procedure is presented for evaluating the sensitivity coefficients of the dynamic axisymmetric, fully-coupled, thermoviscoplastic response of shells of revolution. The analytical formulation is based on Reissner's large deformation shell theory with the effects of large-strain, transverse shear deformation, rotatory inertia and moments turning around the normal to the middle surface included. The material model is chosen to be viscoplasticity with strain hardening and thermal hardening, and an associated flow rule is used with a von Mises effective stress. A mixed formulation is used for the shell equations with the fundamental unknowns consisting of six stress resultants, three generalized displacements and three velocity components. The energy-balance equation is solved using a Galerkin procedure, with the temperature as the fundamental unknown. Spatial discretization is performed in one dimension (meridional direction) for the momentum and constitutive equations of the shell, and in two dimensions (meridional and thickness directions) for the energy-balance equation. The temporal integration is performed by using an explicit central difference scheme (leap-frog method) for the momentum equation; a predictor-corrector version of the trapezoidal rule is used for the energy-balance equation; and an explicit scheme consistent with the central difference method is used to integrate the constitutive equations. The sensitivity coefficients are evaluated by using a direct differentiation approach. Numerical results are presented for a spherical cap subjected to step loading.
Fuel-oxidizer reaction product (FORP), the product of incomplete reaction of monomethylhydrazine and nitrogen tetroxide propellants prepared under laboratory conditions and from firings of Shuttle Reaction Control System thrusters, has been characterized by chemical and thermal analysis. The composition of FORP is variable but falls within a limited range of compositions that depend on three factors: the fuel-oxidizer ratio at the time of formation; whether the composition of the post-formation atmosphere is reducing or oxidizing; and the reaction or post-reaction temperature. A typical composition contains methylhydrazinium nitrate, ammonium nitrate, methylammonium nitrate, and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. Thermal decomposition reactions of the FORP compositions used in this study were unremarkable. Neither the various compositions of FORP, the pure major components of FORP, nor mixtures of FORP with propellant system corrosion products showed any unusual thermal activity when decomposed under laboratory conditions. Off-limit thruster operations were simulated by rapid mixing of liquid monomethylhydrazine and liquid nitrogen tetroxide in a confined space. These tests demonstrated that monomethylhydrazine, methylhydrazinium nitrate, ammonium nitrate, or Inconel corrosion products can induce a mixture of monomethylhydrazine and nitrogen tetroxide to produce component-damaging energies. Damaging events required FORP or metal salts to be present at the initial mixing of monomethylhydrazine and nitrogen tetroxide.
The product of incomplete reaction of monomethylhydrazine (MMH) and nitrogen tetroxide (NTO) propellants, or fuel-oxidizer reaction product (FORP), has been hypothesized as a contributory cause of an anomaly which occurred in the chamber pressure (PC) transducer tube on the Reaction Control Subsystem (RCS) aft thruster 467 on flight STS-51. A small hole was found in the titanium-alloy PC tube at the first bend below the pressure transducer. It was surmised that the hole may have been caused by heat and pressure resulting from ignition of FORP. The NASA Johnson Space Center (JSC) White Sands Test Facility (WSTF) was requested to define the chemical characteristics of FORP, characterize its reactivity, and simulate the events in a controlled environment which may have lead to the Pc-tube failure. Samples of FORP were obtained from the gas-phase reaction of MMH with NTO under laboratory conditions, the pulsed firings of RCS thrusters with modified PC tubes using varied oxidizer or fuel lead times, and the nominal RCS thruster firings at WSTF and Kaiser-Marquardt. Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), ion chromatography (IC), inductively coupled plasma (ICP) spectrometry, thermogravimetric analysis (TGA) coupled to FTIR (TGA/FTIR), and mechanical impact testing were used to qualitatively and quantitatively characterize the chemical, thermal, and ignition properties of FORP. These studies showed that the composition of FORP is variable but falls within a limited range of compositions that depends on the fuel loxidizer ratio at the time of formation, composition of the post-formation atmosphere (reducing or oxidizing), and reaction or postreaction temperature. A typical composition contains methylhydrazinium nitrate (MMHN), ammonium nitrate (AN), methylammonium nitrate (MAN), and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. The thermal decomposition reactions of FORP compositions used in this study were unremarkable, Neither the various compositions of FORP, the pure major components of FORP, nor mixtures of FORP with propellant-system corrosion products showed any unusual thermal activity when decomposed under laboratory conditions. Off-limit thruster operations were simulated by rapid mixing of liquid MMH and liquid NTO in a confined space. The test hardware was constructed with pressure- and temperature-measurement devices to determine if the expected fuel oxidizer reaction would result in increased energy release when FORP, FORP constituents, or propellant-system corrosion products were present. These tests demonstrated that FORP, MMHN, AN, or Inconel corrosion products can induce a mixture of MMH and NTO to produce component-damaging energies. The simulation-test program was not extensive enough to provide statistical probabilities for these events but did show that such events can occur. Damaging events required FORP or metal salts to be present at the initial mixing of MMH and NTO. Based on the results of these studies, it is suggested that removal or mitigation of a buildup of these materials may decrease the incidence of these high-energy, potentially damaging events.
The A-type polyimide adhesive resin P11B was modified by use of mixed diamines (thio-dianiline and meta phenylene diamine) which provided the desired autoclave processability. This new resin was termed P11BA. It was shown that copolymeric blends of P11BA and Amoco AI-1137 amide-imide resin provided improved adhesive properties when autoclave processed over the properties obtained previously by press bonding with P11B based copolymeric blended adhesives. Properties of bonded assemblies are presented for long-term aging at both elevated and low temperatures, and also stress-rupture tests at elevated temperature.
Temperature profiles for four midlatitude regions on Jupiter and an improved value of the H2 molar mixing ratio are obtained from Pioneer 11 IR radiometer data and ground-based IR spectral data. The investigated regions include two in the Southern Hemisphere and two in the Northern Hemisphere, all of which consist of an adjacent belt and zone. The temperature profiles for the pressure regime between 0.1 and 1.0 bar are plotted along with the emitted net flux, flux divergence, and cooling rate for a temperature profile that is an average of those derived for the South Equatorial Belt and a 'cloudy' model of the South Tropical Zone. Averaging of the results obtained with clear and cloudy zone models yields a weighted mean value of 0.88 for the H2 molar mixing ratio, which corresponds to a He/H2 ratio of 0.14. It is emphasized that this value depends on perfect validity of the adopted opacity model, the absence of systematic errors in the data, and other factors. Local effective temperatures for each region are found to range from 124.2 to 127.6 K, which are close to the model-independent global average of 125 K.
Ionization states of elements in the solar wind are often used to determine thermal gradients in the lower corona. This method is based on the assumption, that in the beginning, solar wind material has a homogeneous temperature determining the original charge state of elements. Features in M/Q-spectra which might appear if the above assumption is violated are investigated and compared with observational evidence.
This presentation describes the development of a numerical model that couples the thermal interaction between ice particles, water droplets, and the flowing gas of an icing wind tunnel for simulation of NASA Glenn Research Centers Propulsion Systems Laboratory (PSL). The ultimate goal of the model is to better understand the complex interactions between the test parameters and have greater confidence in the conditions at the test section of the PSL tunnel. The model attempts to explain the observed changes in test conditions by coupling the conservation of mass and energy equations for both the cloud particles and flowing gas mass. Model predictions were compared to measurements taken during May 2015 testing at PSL, where test conditions varied gas temperature, pressure, velocity and humidity levels, as well as the cloud total water content, particle initial temperature, and particle size distribution.
This paper describes the development of a numerical model that couples the thermal interaction between ice particles, water droplets, and the flowing gas of an icing wind tunnel for simulation of NASA Glenn Research Centers Propulsion Systems Laboratory (PSL). The ultimate goal of the model is to better understand the complex interactions between the test parameters and have greater confidence in the conditions at the test section of the PSL tunnel. The model attempts to explain the observed changes in test conditions by coupling the conservation of mass and energy equations for both the cloud particles and flowing gas mass. Model predictions were compared to measurements taken during May 2015 testing at PSL, where test conditions varied gas temperature, pressure, velocity and humidity levels, as well as the cloud total water content, particle initial temperature, and particle size distribution.
Basaltic eucrites, which are possibly parts of the Vestan crust, formed as either lava flows or intrusions, and can offer insights into early crust formation. However most eucrites have experienced thermal metamorphism, which exacerbates the challenges of understanding these samples. A variety of petrogenetic models such as, partial melting of a primitive source, fractional crystallization of magmas emplaced in a primitive crust, and/or partial melting of a eucritic source coupled with melt mixing and assimilation have been proposed in order to explain observed petrologic and chemical characteristics of eucrites. EET 90020 is an unbrecciated eucrite that has experienced significant thermal metamorphism, with temperatures of metamorphic equilibration calculated to be ~840-1040°C. Its petrologic history remains contentious, in part due to differences in trace element analyses [10,17, this work], which has led to multiple metamorphic interpretations [8,10-11]. Here, we combined petrologic observations, chemical analyses, and thermodynamic modeling, to interpret micro-domain textures identified in EET 90020 and better constrain its petrologic history. Ultimately, the development of such textures is a direct result of the geologic processes operating on a young Vesta or similar asteroid. Sample description: We identified three textural domains in EET 90020 (Figure 1); (I) A coarse grain domain with granoblastic plagioclase and pyroxene, (II) a medium grain domain with curved grain boundaries between plagioclase and pyroxene, and (III) a fine grain domain dominated by tridymite that fills in interstitial space between spherical plagioclase. Major element chemistry in phases is consistent across domains. Pyroxene have distinctive high Ca lamellae (Wo40.92En28.1Fs31.0) forming from the low-Ca pigeonite host (Wo3.5En33.7Fs62.8). There are small amounts of fayalitic olivine along pyroxene/oxide grain boundaries, where pyroxenes have reacted with ilmenite/chromite clasts. Plagioclase is anorthitic (Avg ~An88), with little variation (An86-92.5). Trace element bulk rock analyses were collected via ICP-MS and individual mineral analyses with LA-ICP-MS (Figure 2). The bulk sample has an observable enrichment in light rare earth elements, with a notable depletion in Eu. Plagioclase is enriched in LREEs, depleted in HREEs, and has a positive Eu anomaly while pyroxene is enriched in HREEs with a negative Eu anomaly. Variations in trace element analyses is likely influenced by the presence of phosphates because are highly enriched in REEs and have a dramatic effect on the bulk domain compositions. Thermodynamic modeling: The software package, Perple_X, was used to calculate mineral phase equilibria over a range of conditions using a Gibbs free energy minimization approach [12]. Models used all major/minor elements except P2O5. Thermodynamic properties from [13] were used to constrain endmember phase stabilities. Activity models were used to describe mixing in phases with solid solution. Isochemical P-T phase diagrams were constructed for the bulk thin section, and the coarse, medium and fine grain domain compositions. Domain compositions were determined using microprobe analyses of phases identified in each domain and observed modal mineral abundancies. Thermodynamically stable pyroxene compositions were extracted from model results and compared to pyroxene compositions collected via EMPA, allowing us to calculate temperatures for metamorphic equilibrium. Results: Results that use the coarse domain composition (Fig. 3a) demonstrate overlap at T ~ 1020°C indicating high T equilibration. There was no overlap for the medium and fine grain domains, or the bulk composition (e.g., Fig. 3b) indicating that these are not equilibrium assemblages. These results were replicated using data from [8,20]. Discussion: The disequilibrium results from the bulk rock, fine grain and medium grain models imply that EET 90020 was modified during and/or after peak metamorphism (open system behavior). However, this is in contrast to the coarse domain where it appears as if equilibrium was maintained. We suggest that this conflict is explained by highly localized equilibrium occurring at millimeter length-scales, which has been observed in terrestrial metamorphism where aqueous fluid infiltrate [14] or melt loss occurs [15]. It is unlikely that aqueous alteration was significant in modifying the bulk composition of EET 90020, because it lacks hydrated minerals. However, the presence of melt is supported by the presence of an abundance of curved grain boundaries and spherical grains in the medium and fine grain domains This contrasts the coarse domain, where grain boundaries are angular. Given the evidence for disequilibrium in the medium and fine grain domains, it would be inappropriate to draw additional conclusions about textural evolution using thermodynamic models of those domains. However, modeling results of the coarse grain domain, where equilibrium was maintained, can provide useful insights into the geologic evolution of EET 90020. We approximate maximum metamorphic temperatures, using the Ca component in pyroxene, at ~1020°C (Fig. 4), which is consistent with previous two-pyroxene thermometry [11]. At this temperature, up to 10 vol % melt can be produced in the coarse grain domain, which is at the boundary of minimum melt needed in order to segregate and form a melt network [16]. Tridymite and plagioclase would be the first minerals to melt out during heating starting ~990°C. This is consistent with the observed melt textures formed by tridymite and plagioclase in the fine grain domain. We suggest that a partial melting model best explains the textural development of EET 90020. Upon heating, melt generated was either trapped, resulting in no net change in the localized rock composition, or migrated, resulting in disequilibrium between pyroxene and the surrounding matrix. A positive Eu anomaly in plagioclase indicates that all of the plagioclase was melted previously. This is consistent with previous studies that have suggested that EET 90020 represents a residual eucrite that experienced partial melting and subsequent melt loss [8]. We speculate that partial melting could have occurred when EET 90020 was heated in the asteroid’s lower crust or adjacent to an intrusion [7]. Future work will study other, texturally heterogeneous samples to see if EET 90020 presents a unique circumstance or whether crustal partial melting was ubiquitous on the eucrite asteroid.
A squib ignition model based on transient heat condition from the hot bridgewire to the pyrotechnic is described. No Arrhenius-type chemical reaction is included. Instead, a thermal contact resistance is postulated to exist between the hot bridgewire and the pyrotechnic. Ignition is assumed to occur when a 2.5 micron layer of pyrotechnic next to the bridgewire reaches a characteristic ignition temperature for that pyrotechnic. This model was applied to the JPL squib, which uses a 50 micron (0.002-in.) diameter Tophet A bridgewire to ignite a boron, potassium perchlorate mix. A computer program was utilized that solves the transient heat condition problem with the boundary conditions stipulated by the model. The thermal contact conductance at the interface was determined by trial and error so that the experimentally determined ignition time for one firing condition would be properly predicted by the model. The agreement was quite good for tests run between -129 C and +93.3 C at current levels of 3.5 and 5 A. Axial heat conduction along the bridgewire is shown to be negligible.
Spark erosion was used to produce ultra-fine particles of SiGe thermoelectric material and boron nitride, an inert phonon-scattering material. A homogeneous powder was made by mixing the two powders. The mixture was hot pressed to produce a thermoelectric material with uniformity dispersed, ultra-fine, inert, phonon-scattering centers. It is shown that, in samples with inert boron nitride or silicon nitride, thermal conductivity of a SiGe alloy can be reduced by about 25 percent while maintaining the electrical properties of the samples. Annealing of all the samples at 1525 K caused grain growth to over a micron, eliminating the detrimental effect attributable to small grains. Only in the sample with boron nitride the thermal conductivity did remain well below that for standard p-type SiGe (about 25 percent), while the electrical resistivity and Seebeck coefficient were very close to the values for standard p-type 80/20 SiGe.
On the basis of recently calculated models of the Jovian atmosphere, a value of 5.0 was derived for the H2/He mixing ratio from the Pioneer 10 infrared radiometer data. A far-infrared spectrum corresponding to the thermal profile obtained in the Pioneer S-band occultation experiment was also computed. The spectrum strongly suggests a misinterpretation of the data obtained in that experiment.
The effects of chlorine perturbations on both the temperature and the ozone distribution in the stratosphere have been studied using a simplified radiative-photochemical model. The model solves the hydrostatic equation for total density in a self-consistent manner as the temperature is changed. Radiative coupling is found to have a significant effect on both the thermal structure and the ozone distribution, particularly in the 35-50-km region. By increasing the ClX mixing ratio by 5.0 ppbv, the temperature in this region is decreased by 5 to 10 K with a slight increase below 30 km. The local ozone depletion around 40 km due to added ClX is smaller compared with the estimate made by keeping the temperature fixed to the ambient condition. However, the integrated effect of radiative coupling is to increase the calculated column ozone depletion by 15% to 25% in this model.
Thermal perturbations of the solar convection zone can be modeled (to the first order) by perturbing the mixing length parameter alpha (equal to the ratio of the mixing length to the pressure scale height) used in the standard mixing length theory of convection. Results of such an analysis are presented and discussed in relation to recent work by others.
The (Ar-39) (Ar-40) chronologies were determined for 14 different mesosiderites representing the full range of classification according to recrystallization, and these chronologies were compared with analogous data for other meteorite types and for lunar highland rocks. Results of Ar-Ar chronologies indicate the history of a degassing of Ar due to a major thermal event that occurred less than 3.9 Ga ago; this event is not the metal-silicate mixing event, which is known to have occurred earlier than 4.4 Ga ago. It is suggested that a major collisional disruption-reassembly event less than 3.9 Ga ago took place, leaving the metal-silicate breccias buried under tens of kilometers of rubble, where they cooled slowly through the Ar closure temperatures.