Search NASA⌕ Search

SEARCH · Search NASA

Results for “V/STOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Static tests of the J97 powered, external augmenter V/STOL wind tunnel model

Results of the static testing (zero forward speed) of the J97-powered, external augmentor, large scale, V/STOL model are discussed. With a ground clearance of 7.5 feet, believed to have put the model essentially out of ground effect, a gross thrust augmentation ratio of 1.60 at nozzle pressure ratio (NPR) = 3.0 was measured for the fuselage augmentor. A similar figure was apparent for the wing augmentor. An overall ratio of model thrust to bare engine thrust of 1.52 was determined at NPR = 3.0. The structural integrity of the model was well demonstrated and duct pressure losses were small.

Garland, D. B.↗
NASA NTRS1981

Axisymmetric & non-axisymmetric exhaust jet induced-effects on a V/STOL vehicle design. Part 1: Data presentation

A 1/8 scale jet-effects model was tested in the NASA Ames 11 ft transonic tunnel at static conditions and over a range of Mach numbers from 0.4 to 1.4. The data presented show that significant differences in aeropropulsion performance can be expected by varying the exhaust nozzle type and its geometric parameters on a V/STOL underwing nacelle installation.

Schnell, W. C.↗
NASA NTRS1981

Design of a V/STOL propulsion system for a large-scale fighter model

Modifications were made to the existing Large-Scale STOL fighter model to simulate a V/STOL configuration. Modifications include the substitutions of two dimensional lift/cruise exhaust nozzles in the nacelles, and the addition of a third J97 engine in the fuselage to suppy a remote exhaust nozzle simulating a Remote Augmented Lift System. A preliminary design of the inlet and exhaust ducting for the third engine was developed and a detailed design was completed of the hot exhaust ducting and remote nozzle.

Willis, W. S.↗
NASA NTRS1981

Additional testing of the inlets designed for a tandem fan V/STOL nacelle

The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

Ybarra, A. H.↗
NASA NTRS1981

Static test of a fan-powered chin nozzle for V/STOl applications

The performance of a "chin" nozzle which diverts flow in a downward direction immediately downstream of a fan typical of designs suitable for V/STOL A applications was evaluated. Back pressure distortion to the fan and fan discharge pressure distortion were also measured. Results show that the distortion is significant at the closest spacing between the fan exit and cascade entrance tested, and that the chin nozzle performance deteriorates with increased flow diversion to the chin nozzle. Color oil flow visualization on video tape and still photos were also obtained. Tests were conducted behind a 12" model fan in the NASA-Lewis fan calibration facility.

Salemann, V.↗
NASA NTRS1981

Experimental aerodynamic characteristics of two V/STOL fighter/attack aircraft configurations at Mach numbers from 1.6 to 2.0

Tests were conducted in the Ames 9 by 7 ft supersonic wind tunnel to measure the aerodynamic characteristics of two horizontal attitude takeoff and landing V/STOL fighter/attack aircraft concepts. One concept featured a jet diffuser ejector for its vertical lift system and the other employed a remote augmentation lift system (RALS). Test results for Mach numbers from 1.6 to 2.0 are reported. Effects of varying the angle of attack (-4 deg to +17 deg), angle of sideslip (-4 deg to +8 deg) Mach number, and configuration building were investigated. The effects of wing trailing edge flap deflections, canard incidence, and vertical tail deflections were also explored as well as the effects of varying the canard longitudinal location and shapes of the inboard nacelle body strakes.

Nelms, W. P.↗
NASA NTRS1981

Three-dimensional turbulent boundary layer development and separation in V/STOL engine inlets at incidence with small-cross flow and curvature influences

The study concerns the influence of the three-dimensional cross flows on the compressible turbulent boundary layer development and flow separation prediction around V/STOL engine inlets at high incidence. The governing equations for the three-dimensional boundary layer flow with small-cross approximation are solved numerically on an intrinsic streamline coordinate system. Results are presented to illustrate the effects of small cross-flow, compressibility and streamline curvatures on the flow. Comparisons of the results with the wind tunnel data for scaled model and with data obtained from another existing compressible axisymmetric turbulent boundary layer scheme are included in the analysis.

Chou, D. C.↗
NASA NTRS1981

Zero-length inlets for subsonic V/STOL aircraft

Zero-length inlet performance and associated fan blade stresses were determined during model tests in the NASA-LeRC 9-by 15-foot low-speed wind tunnel. The inlet models, which were installed on a 20-inch diameter fan unit, had different inlet lip contraction ratios as well as unslotted, slotted, and double slotted inlet lips. The inlet angle-of-attack boundaries for onset of flow separation were identified and compared to the operating requirements of several generically different subsonic V/STOL aircraft. The zero-length inlets, especially those with slotted lips, were able to satisfy these requirements without compromising the maximum cowl forebody radius. As an aid to the inlet design process, a unique relationship was established between the maximum surface Mach number associated with the separation boundary and the maximum-to-throat surface velocity ratio.

Glasgow, E. R.↗
NASA NTRS1981

Lift-enhancing surfaces on several advanced V/STOL fighter/attack aircraft concepts

An analysis of the relative influences of forward lift-enhancing surfaces on the overall lift and drag characteristics of three wind-tunnel models representative of V/STOL fighter/attack aircraft is presented. Two of the models are canard-wing configurations and one has a wing leading-edge extension (LEX) as the forward lifting surface. Data are taken from wind-tunnel tests of each model covering Mach numbers from 0.4 to 1.4. Overall lift and drag characteristics of these models and the generally favorable interactions of the forward surfaces with the wings are highlighted. Results indicate that larger LEX's and canards generally give greater lift and drag improvements than ones that are smaller relative to the wings.

Durston, D. A.↗
NASA NTRS1981

Thrust modulation methods for a subsonic V/STOL aircraft

Low speed wind tunnel tests were conducted to assess four methods for attaining thrust modulation for V/STOL aircraft. The four methods were: (1) fan speed change, (2) fan nozzle exit area change, (3) variable pitch rotor (VPR) fan, and (4) variable inlet guide vanes (VIGV). The interrelationships between inlet and thrust modulation system were also investigated using a double slotted inlet and thick lip inlet. Results can be summarized as: (1) the VPR and VIGV systems were the most promising, (2) changes in blade angle to obtain changes in fan thrust have significant implications for the inlet, and (3) both systems attained required level of thrust with acceptable levels of fan blade stress.

Woollett, R. R.↗
NASA NTRS1981

Comparison of two parallel/series flow turbofan propulsion concepts for supersonic V/STOL

The thrust, specific fuel consumption, and relative merits of the tandem fan and the dual reverse flow front fan propulsion systems for a supersonic V/STOL aircraft are discussed. Consideration is given to: fan pressure ratio, fan air burning, and variable core supercharging. The special propulsion system components required are described, namely: the deflecting front inlet/nozzle, the aft subsonic inlet, the reverse pitch fan, the variable core supercharger and the low pressure forward burner. The potential benefits for these unconventional systems are indicated.

Luidens, R. W.↗
NASA NTRS1982

V/STOL Tandem Fan transition section model test

An approximately 0.25 scale model of the transition section of a tandem fan variable cycle engine nacelle was tested in the NASA Lewis Research Center 10-by-10 foot wind tunnel. Two 12-inch, tip-turbine driven fans were used to simulate a tandem fan engine. Three testing modes simulated a V/STOL tandem fan airplane. Parallel mode has two separate propulsion streams for maximum low speed performance. A front inlet, fan, and downward vectorable nozzle forms one stream. An auxilliary top inlet provides air to the aft fan - supplying the core engine and aft vectorable nozzle. Front nozzle and top inlet closure, and removal of a blocker door separating the two streams configures the tandem fan for series mode operations as a typical aircraft propulsion system. Transition mode operation is formed by intermediate settings of the front nozzle, blocker door, and top inlet. Emphasis was on the total pressure recovery and flow distortion at the aft fan face. A range of fan flow rates were tested at tunnel airspeeds from 0 to 240 knots, and angles-of-attack from -10 to 40 deg for all three modes. In addition to the model variables for the three modes, model variants of the top inlet were tested in the parallel mode only. These lip variables were: aft lip boundary layer bleed holes, and Three position turning vane. Also a bellmouth extension of the top inlet side lips was tested in parallel mode.

Simpkin, W. E.↗
NASA NTRS1982

Experimental and analytical results of tangential blowing applied to a subsonic V/STOL inlet

Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack.

Burley, R. R.↗
NASA NTRS1982

Axisymmetric and non-axisymmetric exhaust jet induced effects on a V/STOL vehicle design. Part 2: Analysis of results

A wind tunnel investigation, employing a 1/8 scale model in an 11 foot transonic wind tunnel (Mach 0.4-1.4), was conducted to determine the jet effects of several exhaust nozzles on the aeropropulsive performance of a V/STOL fighter design. The force and pressure data show that significant differences in aeropropulsion performance can be expected by varying the exhaust nozzle type, jet area and deflection angle on an underwing nacelle installation. At unvectored conditions, the single expansion ramp nozzles show large performance gains relative to a circular nozzle installation. Additionally, a further drag reduction is realized when the nonaxisymmetric nozzle is vectored through a 10 degree deflection angle. The combined payoff of the vectored nonaxisymmetric nozzle over the baseline circular nozzle installation is equivalent to 25 percent of zero lift drag.

Schnell, W. C.↗
NASA NTRS1982

Axisymmetric and non-axisymmetric exhaust jet induced effects on a V/STOL vehicle design. Part 3: Experimental technique

The jet induced effects of several exhaust nozzle configurations (axisymmetric, and vectoring/modulating varients) on the aeropropulsive performance of a twin engine V/STOL fighter design was determined. A 1/8 scale model was tested in an 11 ft transonic tunnel at static conditions and over a range of Mach Numbers from 0.4 to 1.4. The experimental aspects of the static and wind-on programs are discussed. Jet effects test techniques in general, fow through balance calibrations and tare force corrections, ASME nozzle thrust and mass flow calibrations, test problems and solutions are emphasized.

Schnell, W. C.↗
NASA NTRS1981

Jet V/STOL wind-tunnel simulation and groundplane effects

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. This paper examines some of the pretest preparation necessary to define the objectives of an appropriate investigation. Several factors which influence the selection of the model concept and the engine simulator are discussed. In addition, some of the test techniques important for this class of aircraft model are examined. Finally, the paper reviews some of the wind-tunnel wall effects important to this type of aircraft testing with special emphasis on groundplane effects.

Margason, R. J.↗
NASA NTRS1981

A summary of V/STOL inlet analysis methods

Methods to analyze the aerodynamic performance of V/STOL inlets at the NASA Lewis Research Center are discussed with emphasis on recent extensions and applications. Methods include the specification of the Kutta condition for a slotted inlet, the calculation of suction and tangential blowing for boundary layer control, and the analysis of auxiliary inlet geometries at angles of attack. An optimum diffuser velocity distribution is also developed, which can result in the shortest no-boundary layer control inlet and the lowest loss for the required amount of diffusion.

Hwang, D. P.↗
NASA NTRS1981

Type 'A' V/STOL - One aircraft for all support missions

An investigation is conducted regarding the feasibility of developing a single support aircraft type for the Navy, taking into account the current naval inventory of utility aircraft types. Support mission characteristics are examined, giving attention to antisubmarine warfare, airborne early warning, marine assault, carrier on board delivery/vertical on board delivery, the aerial tanker mission, long-range rescue, surface attack, and aspects of combat, search, and rescue. With the aid of a sample design for a V/STOL aircraft with a medium disc loading lift system it is demonstrated that it is now possible to design an aircraft which, with minor modifications, can meet the wide variety of support missions.

Adelt, W. H.↗