Results for “Vehicle modeling and simulation” — Page 19

NASA NTRS1983

Catalog of selected heavy duty transport energy management models

A catalog of energy management models for heavy duty transport systems powered by diesel engines is presented. The catalog results from a literature survey, supplemented by telephone interviews and mailed questionnaires to discover the major computer models currently used in the transportation industry in the following categories: heavy duty transport systems, which consist of highway (vehicle simulation), marine (ship simulation), rail (locomotive simulation), and pipeline (pumping station simulation); and heavy duty diesel engines, which involve models that match the intake/exhaust system to the engine, fuel efficiency, emissions, combustion chamber shape, fuel injection system, heat transfer, intake/exhaust system, operating performance, and waste heat utilization devices, i.e., turbocharger, bottoming cycle.

Colello, R. G.↗

NASA NTRSDate not supplied

A Green’s Function Sensor Fusion Approach for Evaluating Spacecraft Entry Heating From on-Board Thermal Instrumentation

During atmospheric entry, distributed thermal measurements are critical to enable the evaluation of heat loads on spacecraft thermal protection systems (TPS). In recent space exploration missions, Schmidt-Boelter-type heat flux gauges have been integrated into the TPS alongside conventional temperature measurement instrumentation to measure total (convective and radiative) and radiative heat transfer rates1,2. While direct heat flux sensors (HFS) are able to provide valuable information detailing the thermal loads experienced by spacecraft, the interpretation of these measurements in unsteady, convective environments requires a correction factor to account for local heating augmentations at the cold wall HFS surface2,3. Current efforts to estimate cold wall correction factors, and thus recover the hot wall TPS heat flux, rely on time-marching computational fluid dynamics (CFD) simulations2. Simulation-based methods are susceptible to large uncertainties, however, as they require estimations of vehicle trajectory, gas kinetics, wall catalysis models, and other flight conditions as input parameters2,4. Furthermore, CFD simulations are computationally expensive and cannot efficiently survey all possible entry scenarios, exacerbating the uncertainty of reconstructed hot wall heat flux values. These drawbacks motivate the development of alternative hot wall heat flux reconstruction methods that are not reliant on CFD-based correction factors.

Kenneth McAfee↗

NASA NTRSDate not supplied

A Green’s Function Sensor Fusion Approach for Evaluating Spacecraft Entry Heating From on-Board Thermal Instrumentation

During atmospheric entry, distributed thermal measurements are critical to enable the evaluation of heat loads on spacecraft thermal protection systems (TPS). In recent space exploration missions, Schmidt-Boelter-type heat flux gauges have been integrated into the TPS alongside conventional temperature measurement instrumentation to measure total (convective and radiative) and radiative heat transfer rates1,2. While direct heat flux sensors (HFS) are able to provide valuable information detailing the thermal loads experienced by spacecraft, the interpretation of these measurements in unsteady, convective environments requires a correction factor to account for local heating augmentations at the cold wall HFS surface2,3. Current efforts to estimate cold wall correction factors, and thus recover the hot wall TPS heat flux, rely on time-marching computational fluid dynamics (CFD) simulations2. Simulation-based methods are susceptible to large uncertainties, however, as they require estimations of vehicle trajectory, gas kinetics, wall catalysis models, and other flight conditions as input parameters2,4. Furthermore, CFD simulations are computationally expensive and cannot efficiently survey all possible entry scenarios, exacerbating the uncertainty of reconstructed hot wall heat flux values. These drawbacks motivate the development of alternative hot wall heat flux reconstruction methods that are not reliant on CFD-based correction factors.

Kenneth McAfee↗

NASA NTRSDate not supplied

A Green’s Function Sensor Fusion Approach for Evaluating Spacecraft Entry Heating From on-Board Thermal Instrumentation

During atmospheric entry, distributed thermal measurements are critical to enable the evaluation of heat loads on spacecraft thermal protection systems (TPS). In recent space exploration missions, Schmidt-Boelter-type heat flux gauges have been integrated into the TPS alongside conventional temperature measurement instrumentation to measure total (convective and radiative) and radiative heat transfer rates1,2. While direct heat flux sensors (HFS) are able to provide valuable information detailing the thermal loads experienced by spacecraft, the interpretation of these measurements in unsteady, convective environments requires a correction factor to account for local heating augmentations at the cold wall HFS surface2,3. Current efforts to estimate cold wall correction factors, and thus recover the hot wall TPS heat flux, rely on time-marching computational fluid dynamics (CFD) simulations2. Simulation-based methods are susceptible to large uncertainties, however, as they require estimations of vehicle trajectory, gas kinetics, wall catalysis models, and other flight conditions as input parameters2,4. Furthermore, CFD simulations are computationally expensive and cannot efficiently survey all possible entry scenarios, exacerbating the uncertainty of reconstructed hot wall heat flux values. These drawbacks motivate the development of alternative hot wall heat flux reconstruction methods that are not reliant on CFD-based correction factors.

Kenneth McAfee↗

NASA NTRSDate not supplied

Regional Modeling and Simulation for Vertiport Location Assessment

There is increasing interest in the Urban Air Mobility concept and the realization of electric Vertical Take-Off and Landing (e-VTOL) vehicles flying in the National Airspace System. NASA, FAA, and the industry are investigating various aspects of this new mode of transportation for cargo and humans. There are significant challenges in making this mode a reality, including feasibility, safety, infrastructure, traffic management, public acceptance, and scalability. From the infrastructure perspective, one of the aspects that needs to be addressed is the location of vertiports (named similar to heliports, for vertical take-off and landing vehicles). There is significant on-going research for selecting location of vertiports. However, the locations are largely based on demand models. Also, these efforts are focused in specific local regions, San Francisco/Bay Area, Chicago, Tampa, etc. This talk presents an approach to determine the location of vertiports in regional areas (across the United States), incorporating the desire to have certain attributes closer to or further from the location using a regional modeling tool. The feasibility of flying e-VTOL vehicles between various vertiport locations is also presented using a mobility operations simulation tool.

Air Mobility↗

NASA NTRS1988

Analysis procedures and subjective flight results of a simulator validation and cue fidelity experiment

A joint experiment to investigate simulator validation and cue fidelity was conducted by the Dryden Flight Research Facility of NASA Ames Research Center (Ames-Dryden) and NASA Langley Research Center. The primary objective was to validate the use of a closed-loop pilot-vehicle mathematical model as an analytical tool for optimizing the tradeoff between simulator fidelity requirements and simulator cost. The validation process includes comparing model predictions with simulation and flight test results to evaluate various hypotheses for differences in motion and visual cues and information transfer. A group of five pilots flew air-to-air tracking maneuvers in the Langley differential maneuvering simulator and visual motion simulator and in an F-14 aircraft at Ames-Dryden. The simulators used motion and visual cueing devices including a g-seat, a helmet loader, wide field-of-view horizon, and a motion base platform.

Carr, Peter C.↗

NASA NTRSDate not supplied

Methods for System-Level Multidisciplinary Uncertainty Analysis of Low-Boom Flight Vehicles

Current research supporting NASA’s Commercial Supersonic Technology project is focused on the efficient prediction of uncertainty in sonic boom loudness generated by low-boom aircraft concepts. This paper focuses on research incorporating aircraft trim and aerostructural analysis into a multidisciplinary system-level uncertainty analysis. This enables the modeling of a steady-state representation of a point in the uncertainty space, simulating the vehicle as it would be flown. This approach also enables multiple uncertain parameters defining the configuration of the vehicle to be reduced to three: Mach number, altitude, and aircraft weight. To demonstrate this methodology, a case study exploring a conceptual low-boom supersonic aircraft is performed. Two different approaches are used to model the interactions between nearfield pressure signature analysis and sonic boom propagation, and their performance is evaluated in terms of accuracy and computational expense. One method uses a set of local surrogate models to generate a large number of nearfield signatures and perform Monte Carlo analysis. This method is found to produce, at a lower expense, uncertainty metrics that are comparable to the second method, in which uncertainty metrics are computed based on loudness metric values obtained directly from simulated nearfield signatures.

UQ↗

NASA NTRSDate not supplied

Method for System-Level Multidisciplinary Uncertainty Analysis of Low-Boom Flight Vehicles

Current research supporting NASA’s Commercial Supersonic Technology project is focused on the efficient prediction of uncertainty in sonic boom loudness generated by low-boom aircraft concepts. This paper focuses on research incorporating aircraft trim and aerostructural analysis into a multidisciplinary system-level uncertainty analysis. This enables the modeling of a steady-state representation of a point in the uncertainty space, simulating the vehicle as it would be flown. This approach also enables multiple uncertain parameters defining the configuration of the vehicle to be reduced to three: Mach number, altitude, and aircraft weight. To demonstrate this methodology, a case study exploring a conceptual low-boom supersonic aircraft is performed. Two different approaches are used to model the interactions between nearfield pressure signature analysis and sonic boom propagation, and their performance is evaluated in terms of accuracy and computational expense. One method uses a set of local surrogate models to generate a large number of nearfield signatures and perform Monte Carlo analysis. This method is found to produce, at a lower expense, uncertainty metrics that are comparable to the second method, in which uncertainty metrics are computed based on loudness metric values obtained directly from simulated nearfield signatures.

Supersonics↗

NASA NTRS1991

Piloted simulator studies of the HL-20 Lifting Body

An overview is presented of the concept, design and development of the NASA Langley Lifting Body, and the flight simulator studies that have been performed. Attention is given to the aerodynamic shape of the HL-20, vehicle and simulator/cockpit description, and evolution of the HL-20 aerodynamic model. The flight simulation studies have demonstrated the HL-20 to be a viable design for accomplishing precise, unpowered, horizontal landings.

Rivers, Robert A.↗

NASA NTRS2013

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression

of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Scott, Robert C.↗

NASA NTRSDate not supplied

From Simulation to Reality With Random Noise

The challenging environment of autonomous vehicle (AV) navigation necessitates certain functions be performed by deep neural networks. Optimizing these models involves collecting vast quantities of domain-specific training data and ensuring that the dataset is representative of expected conditions. High-fidelity simulation plays a vital role in making this process feasible, allowing a wide range of scenarios to be explored at low cost. However, learning from simulation introduces subtle biases into models, which can degrade real-world performance in unpredictable ways. This effect can be mitigated with learning schemes specialized to bridge distributional shifts (transfer learning). Given the complex nature of these methods, the underlying models, and their environments, meaningfully evaluating performance is notstraight forward. Many unrelated factors can effect an improvement in generalization accuracy, but a full ablation analysis is often difficult. To tease out signal from noise, it is necessary to understand how transfer learning performance is affected by noise itself. The goals of this paper are (i) to establish a domain randomization baseline for a simple classification transfer learning task and (ii) to validate the RRAV testbed as a platform for further research in sim-to-real learning. We generate imagery from a simulation of NASA Ames Research Center and train a small convolutional neural network (ConvNet) to classify position relative to a centerline. Further models are trained with different types of noise progressively added to the data. The models are deployed aboard the on-site test vehicle to test real-world performance. In our experiments, we find that such naive domain randomization raises sim-to-real accuracy from 64% to 79%, while training directly on real data yields an 89% accuracy ceiling. These results suggest that the isolated mechanism of domain randomization can significantly improve generalization.

simulation↗

NASA NTRS2024

Computational Techniques to Generate Space Launch System Aerodynamic Databases

This document describes the reasoning and trade studies used to evaluate tools for constructing the aerodynamic lineload databases for the liftoff and transition phases of flight for the Space Launch System. Three computational fluid dynamics codes (USM3D, FUN3D, Kestrel) were investigated with various turbulence models, as well as detached eddy simulation variants for the launch vehicle in free air and in proximity to the tower. Decisions were made mostly based on results from brief developmental studies performed in response to specific, unforeseen challenges that were encountered in the analysis of a given configuration. The need to develop databases in a timely manner, as well as accurately capture the expected leeward-wake flowfield characteristics, led to the selection of the Kestrel flow solver with its delayed detached eddy simulation method, the Spalart-Allmaras turbulence model, and the adaptive mesh refinement capability in the off-body Cartesian grid region.

Karen A. Deere↗

NASA NTRS1991

Optimal input design for aircraft instrumentation systematic error estimation

A new technique for designing optimal flight test inputs for accurate estimation of instrumentation systematic errors was developed and demonstrated. A simulation model of the F-18 High Angle of Attack Research Vehicle (HARV) aircraft was used to evaluate the effectiveness of the optimal input compared to input recorded during flight test. Instrumentation systematic error parameter estimates and their standard errors were compared. It was found that the optimal input design improved error parameter estimates and their accuracies for a fixed time input design. Pilot acceptability of the optimal input design was demonstrated using a six degree-of-freedom fixed base piloted simulation of the F-18 HARV. The technique described in this work provides a practical, optimal procedure for designing inputs for data compatibility experiments.

Morelli, Eugene A.↗

NASA NTRS1994

Measurement uncertainty and feasibility study of a flush airdata system for a hypersonic flight experiment

Presented is a feasibility and error analysis for a hypersonic flush airdata system on a hypersonic flight experiment (HYFLITE). HYFLITE heating loads make intrusive airdata measurement impractical. Although this analysis is specifically for the HYFLITE vehicle and trajectory, the problems analyzed are generally applicable to hypersonic vehicles. A layout of the flush-port matrix is shown. Surface pressures are related airdata parameters using a simple aerodynamic model. The model is linearized using small perturbations and inverted using nonlinear least-squares. Effects of various error sources on the overall uncertainty are evaluated using an error simulation. Error sources modeled include boundarylayer/viscous interactions, pneumatic lag, thermal transpiration in the sensor pressure tubing, misalignment in the matrix layout, thermal warping of the vehicle nose, sampling resolution, and transducer error. Using simulated pressure data for input to the estimation algorithm, effects caused by various error sources are analyzed by comparing estimator outputs with the original trajectory. To obtain ensemble averages the simulation is run repeatedly and output statistics are compiled. Output errors resulting from the various error sources are presented as a function of Mach number. Final uncertainties with all modeled error sources included are presented as a function of Mach number.

Whitmore, Stephen A.↗

NASA NTRSDate not supplied

Improving Kinetic Consistency Across Elastic Model Transitions With Quadratic Inequality Constrained Weighted Least Squares (WLSQI)

Flexible body modeling presents a large challenge in the development of simulations to aid in design of flight control systems for launch and landing vehicles. Typically, the flexible body model is not a single continuous model but are rather discrete sets of Linear Time Invariant (LTI) Finite Element Models (FEM) incremented by propellant levels. This introduces the problem of smoothly transitioning modal and physical states of the vehicle when switching from one FEM to the next. This paper introduces a new approach to optimally transition flexible body states with weighted least squares, building off previous methods.

GN&C↗

NASA NTRS1985

Control of a free-flying robot manipulator system

The goal of the research is to develop and test control strategies for a self-contained, free flying space robot. Such a robot would perform operations in space similar to those currently handled by astronauts during extravehicular activity (EVA). The focus of the work is to develop and carry out a program of research with a series of physical Satellite Robot Simulator Vehicles (SRSV's), two-dimensionally freely mobile laboratory models of autonomous free-flying space robots such as might perform extravehicular functions associated with operation of a space station or repair of orbiting satellites. The development of the SRSV and of some of the controller subsystems are discribed. The two-link arm was fitted to the SRSV base, and researchers explored the open-loop characteristics of the arm and thruster actuators. Work began on building the software foundation necessary for use of the on-board computer, as well as hardware and software for a local vision system for target identification and tracking.

Alexander, H.↗

NASA NTRS1986

Control of a free-flying robot manipulator system

The development of and test control strategies for self-contained, autonomous free flying space robots are discussed. Such a robot would perform operations in space similar to those currently handled by astronauts during extravehicular activity (EVA). Use of robots should reduce the expense and danger attending EVA both by providing assistance to astronauts and in many cases by eliminating altogether the need for human EVA, thus greatly enhancing the scope and flexibility of space assembly and repair activities. The focus of the work is to develop and carry out a program of research with a series of physical Satellite Robot Simulator Vehicles (SRSV's), two-dimensionally freely mobile laboratory models of autonomous free-flying space robots such as might perform extravehicular functions associated with operation of a space station or repair of orbiting satellites. It is planned, in a later phase, to extend the research to three dimensions by carrying out experiments in the Space Shuttle cargo bay.

Alexander, H.↗

NASA NTRS1992

The new challenge of computational aeroscience

This paper discusses NASA's Computational Aerosciences (CAS) Project of the High Performance Computing and Communications Program (HPCCP). The project is aimed at developing advanced, multidisciplinary simulation capabilities for aerospace vehicle and propulsion system design. It is also aimed at overcoming computational performance barriers by accelerating the development of parallel computer technology. The goals and approach of the CAS Project are described and the challenges to its implementation are addressed. Specific vehicle class simulations to be demonstrated and the principal mutidisciplinary modeling approaches to be emphasized are described. The computational speed and memory requirements for representative multidisciplinary applications are estimated. Finally, the state of parallel computer technology including programming issues and the results of performance measurements are explored.

Bailey, F. R.↗