SEARCH · Search NASA

Results for “Well clear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Analysis of a resistance-energy balance method for estimating daily evaporation from wheat plots using one-time-of-day infrared temperature observations

Accurate estimates of evaporation over field-scale or larger areas are needed in hydrologic studies, irrigation scheduling, and meteorology. Remotely sensed surface temperature might be used in a model to calculate evaporation. A resistance-energy balance model, which combines an energy balance equation, the Penman-Monteith (1981) evaporation equation, and van den Honert's (1948) equation for water extraction by plant roots, is analyzed for estimating daily evaporation from wheat using postnoon canopy temperature measurements. Additional data requirements are half-hourly averages of solar radiation, air and dew point temperatures, and wind speed, along with reasonable estimates of canopy emissivity, albedo, height, and leaf area index. Evaporation fluxes were measured in the field by precision weighing lysimeters for well-watered and water-stressed wheat. Errors in computed daily evaporation were generally less than 10 percent, while errors in cumulative evaporation for 10 clear sky days were less than 5 percent for both well-watered and water-stressed wheat. Some results from sensitivity analysis of the model are also given.

Choudhury, B. J.↗

NASA NTRS1999

Measurement of Temperature Fluctuations and Microscopic Growth Rates in a Silicon Floating Zone and Microgravity

A silicon crystal growth experiment has been accomplished using the floating-zone technique under microgravity on a sounding rocket (TEXUS 36). Measurements of temperature fluctuations in the silicon melt zone due to time dependent thermocapillary convection (Marangoni convection) and an observation of the microscopic growth rate were simultaneously performed during the experiment. Temperature fluctuations of about 0.5 - 0.7 C with a frequency range < 0.5Hz were detectable. The microscopic growth rate fluctuates considerably around the average growth rate of 1 mm/min: Growth rates up to 3 to 4mm/min, close to zero mm/min, as well as negative values (backmelting) were observed. Dopant striations are clearly visible in the Sb-doped crystal. They were characterized by Spreading Resistance measurements and Differential Interference Contrast microscopy. The frequencies of temperature fluctuations, microscopic growth rates, and the dopant inhomogeneities correspond quite well, with main frequencies between 0.1 and 0.3 Hz. 3D numerical simulations were performed to predict the optimum position of the temperature sensor, and the characteristic temperature amplitudes and frequencies. At a position 3.4mm above the interface and 1.4mm inside the melt, equivalent to the sensor tip position in the experiment, temperature fluctuations up to 1.8 C and frequencies ? 0.25Hz were found in the simulations.

Schweizer, Markus↗

NASA NTRSDate not supplied

TPSAS-NF1676L-11084-DND

The solar radiation must be considered as the primary factor when we study the climatic system because it provides almost all energy that drives the climatic system and most atmospheric phenomena. The solar radiation at the TOA is partially transferred, transformed into other forms of energy that are eventually dissipated by the general circulation of the atmosphere and oceans, and partially used in chemical and biological processes. The absorption of solar energy in the atmosphere (Acol) plays a key role in the climate system, not only because it affects the amount of solar energy absorbed by the Earth system, but also because it changes the vertical distribution of absorbed energy, which in turn impacts surface evaporation, atmospheric convection and precipitation. To investigate Acol, we have collected the collocated satellite-surface observations over the 35 selected BSRN surface sites during the period 2000-2004. The surface radiation budgets are averaged from the BSRN Shortwave (SW) observations over a 1-hour interval centered at the time of the NASA Terra and Aqua satellites overpass, and the TOA radiation budgets are averaged from the closest FOV satellite data to the BSRN stations. Then the atmospheric column SW absorption will be inferred from the satellite TOA albedo and BSRN surface absorption (through the estimated surface albedo). Monthly means of Acol, TOA albedo, and surface absorption have been calculated under both clear- and all-sky conditions over the 35 selected BSRN sites which represent different climate regimes. To evaluate the GCM simulations, we have collected the ECHAM5-HAM simulated surface, TOA and atmospheric radiation budgets by researchers at ETH Zurich and compared those simulations with observations. The preliminary comparisons have shown that the ECHAM5 simulated clear-sky surface absorption, TOA albedo, and ACOL agree very well (1-3%) with observations. Under all-sky conditions, they have strong correlations with CERES-derived cloud fraction. The simulated surface absorption is lower and TOA albedo is higher than those under clear skies, but ACOL does not increase too much. However, there are relatively large differences over some regions and months. A further study is needed.

X. Dong↗

NASA NTRS2011

Validation of the MODIS "Clear-Sky" Surface Temperature of the Greenland Ice Sheet

Surface temperatures on the Greenland Ice Sheet have been studied on the ground, using automatic weather station (AWS) data from the Greenland-Climate Network (GC-Net), and from analysis of satellite sensor data. Using Advanced Very High Frequency Radiometer (AVHRR) weekly surface temperature maps, warming of the surface of the Greenland Ice Sheet has been documented from 1981 to present. We extend and refine this record using higher-resolution Moderate-Resolution Imaging Spectroradiometer (MODIS) data from March 2000 to the present. To permit changes to be observed over time, we are developing a well-characterized monthly climate-data record (CDR) of the "clear-sky" surface temperature of the Greenland Ice Sheet using data from both the Terra and Aqua satellites. We use the MODIS ice-surface temperature (IST) algorithm. Validation of the CDR consists of several facets: 1) comparisons between the Terra and Aqua IST maps; 2) comparisons between ISTs and in-situ measurements; 3) comparisons between ISTs and AWS data; and 4) comparisons of ISTs with surface temperatures derived from other satellite instruments such as the Thermal Emission and Reflection Radiometer. In this work, we focus on 1) and 2) above. Surface temperatures on the Greenland Ice Sheet have been studied on the ground, using automatic weather station (AWS) data from the Greenland-Climate Network (GC-Net), and from analysis of satellite sensor data. Using Advanced Very High Frequency Radiometer (AVHRR) weekly surface temperature maps, warming of the surface of the Greenland Ice Sheet has been documented from 1981 to present. We extend and refine this record using higher-resolution Moderate-Resolution Imaging Spectroradiometer (MODIS) data from March 2000 to the present. To permit changes to be observed over time, we are developing a well-characterized monthly climate-data record (CDR) of the "clear-sky" surface temperature of the Greenland Ice Sheet using data from both the Terra and Aqua satellites. We use the MODIS ice-surface temperature (IST) algorithm. Validation of the CDR consists of several facets: 1) comparisons between the Terra and Aqua IST maps; 2) comparisons between ISTs and in-situ measurements; 3) comparisons between ISTs and AWS data; and 4) comparisons of ISTs with surface temperatures derived from other satellite instruments such as the Thermal Emission and Reflection Radiometer. In this work, we focus on 1) and 2) above. First we provide comparisons between Terra and Aqua swath-based ISTs at approximately 14:00 Local Solar Time, reprojected to 12.5 km polar stereographic cells. Results show good correspondence when Terra and Aqua data were acquired within 2 hrs of each other. For example, for a cell centered over Summit Camp (72.58 N, 38.5 W), the average agreement between Terra and Aqua ISTs is 0.74 K (February 2003), 0.47 K (April 2003), 0.7 K (August 2003) and 0.96 K (October 2003) with the Terra ISTs being generally lower than the Aqua ISTs. More precise comparisons will be calculated using pixel data at the swath level, and correspondence between Terra and Aqua IST is expected to be closer. (Because of cloud cover and other considerations, only a few common cloud-free swaths are typically available for each month for comparison.) Additionally, previous work comparing land-surface temperatures (LSTs) from the standard MODIS LST product and in-situ surface-temperature data at Summit Camp on the Greenland Ice Sheet show that Terra MODIS LSTs are about 3 K lower than in-situ temperatures at Summit Camp, during the winter of 2008-09. This work will be repeated using both Terra and Aqua IST pixel data (in place of LST data). In conclusion, we demonstrate that the uncertainties in the CDR will be well characterized as we work through the various facets of its validation.

Hall, Dorothy K.↗

DOE OSTI2023

Conclusions from 3 years of continuous capture plant operation without exchange of the AMP/PZ-based solvent at Niederaussem – insights into solvent degradation management

A many times heard mantra of solvent degradation management in amine-based post combustion capture is “keep the solvent clean” to minimize solvent consumption. It is assumed that the amine losses would decrease by the removal of metals, degradation products, and reactive trace components which are captured from the flue gas, like NO 2 (as potentially driving components of the amine degradation besides dissolved O 2 ). However, this theoretical hypothesis – based on results from laboratory experiments typically generated with fresh amines – disregards the complexity of the solvent matrix, interaction of potential metal catalysts with degradation products and oxidizing agents, and specific chemical requirements which must be fulfilled before a degradation mechanism can proceed. Degradation of the solvent CESAR1 (aqueous solution of 3.0 molar 2-amino-2-methylpropan-1-ol (AMP) and 1.5 molar piperazine (PZ)) is investigated in a unique long-time test campaign (testing time up to now 40 months; 24/7 operation) without replacement of the solvent inventory at the capture pilot plant at the lignite-fired power plant in Niederaussem. Three solvent management strategies with different effect mechanisms are investigated and evaluated: (a) removal of only anionic compounds and trace elements (within 75 days solvent inventory treated two times) and anionic as well as cationic compounds and trace elements (114 days, inventory treated four times) from the solvent by ion exchange, (b) adsorptive removal of trace elements from the solvent by active carbon in 35% of the operating time, and (c) removal of >80% NO 2 by flue gas pretreatment with thiosulfate/sulfite solution (dosing for 2,000 h). The results of the testing program clearly show that “solvent cleanliness” is not a well-defined parameter and that results from laboratory tests, tests without fully representative industrial flue gasses, and short-term testing of monoethanolamine cannot be generalized for other solvents and industrial application. Furthermore, these results showcase that specific degradation management considering solvent, capture plant and flue gas quality is reasonable. Overshooting efforts for solvent management are contra-productive and produce unnecessary waste streams, efficiency losses and costs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Cloud, Aerosol, and Radiative Properties Over the Western North Atlantic Ocean

This study examines the atmospheric properties of weather states (WSs) derived from the International Satellite Cloud Climatology Project (ISCCP) over the Western North Atlantic Ocean. In particular, radiation and aerosol data corresponding to two sites in the study domain, Pennsylvania State University and Bermuda, were examined to characterize the atmospheric properties of the various satellite-derived WSs. At both sites, the fair weather WS was most prevalent, followed by the cirrus WS. Differences in the seasonality of the various WSs were observed at the two sites. Fractional sky cover and effective shortwave cloud transmissivity derived from ground-based radiation measurements were able to capture differences among the satellite-derived WSs. Speciated aerosol optical thicknesses (AOT) from the Modern-Era Retrospective Analysis for Research and Applications, version 2 (MERRA-2) were used to investigate potential differences in aerosol properties among the WSs. The clear sky WS exhibited below-average seasonal values of AOT at both sites year-round, as well as relatively high rates of occurrence with low AOT events. In addition, the clear sky WS showed above-average contributions from dust and black carbon to the total AOT year-round. Finally, transitions between various WSs were examined under low, high, and mid-range AOT conditions. The most common pathway was for the WSs to remain in the same state after a 3 hr interval. Some WSs, such as midlatitude storms, deep convection, middle top, and shallow cumulus, were more prevalent as ending states under high AOT conditions. This work motivates examining differences in aerosol properties between WSs in other regions.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1987

Pseudomorphic InGaAs/AlGaAs modulation-doped FET's with reduced low-frequency noise and thermally stable performance

A high-performance MODFET structure grown by MBE with the incorporation of a single quantum well In(0.15)Ga(0.85)As layer for the transport of two-dimensional electron gas has been critically examined for its thermal stability at 80 K and low-frequency noise form 0.01 to 10 to the 8th Hz. Experimental results indicate that the behavior of this device in both these respects is much superior when compared with the same behavior of conventional MODFETs. A maximum low-field carrier mobility of 29,000 sq cm/s at 80 K and an average carrier saturation velocity of 2 x 10 to the 7th cm/s at 300 K in a 1-micron gate device clearly indicate that the quality of the pseudomorphic quantum well (InGaAs) layer is either comparable or better than that of the usual GaAs buffer layer. The deep level spectra, obtained through photo-FET measurements, and the low-frequency noise spectra at different temperatures obtained for the new pseudomorphic and conventional MODFET's have clearly indicated that contributions from various deep levels present in the new structure are significantly reduced.

Liu, Shih-Ming↗

DOE OSTI2022

Tropical Cirrus in Global Storm-Resolving Models: 1. Role of Deep Convection

Pervasive cirrus clouds in the upper troposphere and tropical tropopause layer (TTL) influence the climate by altering the top-of-atmosphere radiation balance and stratospheric water vapor budget. These cirrus are often associated with deep convection, which global climate models must parameterize and struggle to accurately simulate. By comparing high-resolution global storm-resolving models from the Dynamics of the Atmospheric general circulation Modeled On Non-hydrostatic Domains (DYAMOND) intercomparison that explicitly simulate deep convection to satellite observations, we assess how well these models simulate deep convection, convectively generated cirrus, and deep convective injection of water into the TTL over representative tropical land and ocean regions. The DYAMOND models simulate deep convective precipitation, organization, and cloud structure fairly well over land and ocean regions, but with clear intermodel differences. All models produce frequent overshooting convection whose strongest updrafts humidify the TTL and are its main source of frozen water. Intermodel differences in cloud properties and convective injection exceed differences between land and ocean regions in each model. We argue that, with further improvements, global storm-resolving models can better represent tropical cirrus and deep convection in present and future climates than coarser-resolution climate models. To realize this potential, they must use available observations to perfect their ice microphysics and dynamical flow solvers.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

On-the-fly data set combinations with RNTuple

With the expected data volume increase for HL-LHC and the even more complex computing challenges set by future colliders, the need for efficient data storage and processing becomes more pressing. ROOT’s next-generation data format and I/O subsystem, RNTTuple, is designed to address these challenges. RNTTuple already demonstrates a clear improvement in storage and I/O efficiency, as well as overall stability and robustness with respect to its predecessor, TTTree. These improvements provide a solid baseline to introduce novel extensions to common high-energy and nuclear physics (HENP) workflows. Notably, many workflows could benefit from the ability to arbitrarily join and chain data set samples at runtime, which could reduce overall storage requirements and improve application runtime and ergonomics. In this paper, we present the RNTupleProcessor, which enables HENP data set combinations with RNTuple. We will discuss the main design considerations, present the interfaces to support data set combinations and show how they integrate in typical workflows.

de Geus, Florine Willemijn [CERN; Twente U., Ensch↗

DOE OSTI2024

Real-Time Testbed for Transmission Line Protection

Hardware in the loop (HIL) testing is crucial for designing and managing electric power grids. These grids are becoming larger and more complex. The importance for students to have safe and intuitive ways to interact with the devices associated with the power grids has never been more crucial. Since most of these tests involve high voltages, this can be a deterrent for instructors and students in undergraduate programs. HIL testing is a solution to these common issues. This method has become one of the most popular methods for testing these power systems. With the use of Western Michigan University’s (WMU) Real-Time Digital Simulator (RTDS) and SEL-421-7 protection relay, a HIL testbed has been created. These devices were interconnected using the communication protocol known as Generic Object-Oriented Substation Event (GOOSE). A simulated transmission line system was modeled in an RTDS software RSCAD as the basis for this testbed. This model simulated different types of faults that could occur in a transmission line while in operation. The SEL-421-7 relay is connected to the RSCAD simulation via GOOSE to protect our simulated transmission line. This testbed was set up to give students a clear understanding of how distance protection works as well as how the SEL-421-7 will react to various kinds of faults, in addition to how useful the RTDS can be when testing different power systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS1980

Instability process in low Reynolds number supersonic jets

The objective of the present research was to characterize the instability of supersonic jets of Mach numbers 1.4, 2.1, and 2.5 in the Reynolds number range around 8000. In this Reynolds number range the jet instability has its maximum coherence so that its properties as well as the acoustic properties can be most clearly identified. Growth rate, wavelength, and wave orientation of dominant spectral components of the instability for the three Mach number jets were measured in order to characterize the instability. The saturation and subsequent decay on the instability are coincident with a drastic decrease in the coherence of the instability. Associated research shows that the phenomenon of rapid growth and decay is of fundamental importance in the noise generation process.

Morrison, G. L.↗

NASA NTRS1982

Dynamics and mechanism of cavitation erosion on perspex and epoxy resins tested in a rotating disk device

The cavitation erosion behavior including the initiation, dynamics and mechanism of damage process on perspex and epoxy resin specimens tested in a rotating disk device were discussed with respect to exposure time. The inception of erosion always took place at the location nearest to the center of rotation of the disk. Subsequently, as exposure time increased, erosion initiated at other locations as well. Light optical photographs and scanning electron micrographs clearly indicate that most of the material loss appears to occur form the networks of cracks due to their interaction and pits indicate particle debris. The optical degradation (loss of transmittance) on perspex was observed to be more on the rear side than on the front side.

Rao, P. V.↗

NASA NTRS1983

Cavitation erosion characteristics of poly(methyl methacrylate) in a rotating disk device

Veerabhadra Rao, P.↗

NASA NTRS1986

Turbulence in a convective marine atmospheric boundary layer

The structure and kinetic energy budget of turbulence in the convective marine atmospheric boundary layer as observed by aircraft during a cold air outbreak have been studied using mixed layer scaling. The results are significantly different from those of previous studies under conditions closer to free convection. The normalized turbulent kinetic energy and turbulent transport are about twice those found during the Air Mass Transformation Experiment (AMTEX). This implies that for a given surface heating the present case is dynamically more active. The difference is mainly due to the greater importance of wind shear in the present case. This case is closer to the roll vortex regime, whereas AMTEX observed mesoscale cellular convection which is closer to free convection. Shear generation is found to provide a significant energy source, in addition to buoyancy production, to maintain a larger normalized turbulent kinetic energy and to balance a larger normalized dissipation. The interaction between turbulent pressure and divergence (i.e., pressure scrambling) is also found to transfer energy from the vertical to the horizontal components, and is expected to be stronger in roll vortices than in m esoscale cells. The sensible heat flux is found to fit well with a linear vertical profile in a clear or subcloud planetary boundary layer (PBL), in good agreement with the results of Lenschow et al., (1980). The heat flux ratio between the PBL top and the surface, derived from the linear fitted curve, is approximately -0.14, in good agreement with that derived from the lidar data for the same case. Near the PBL top, the heat flux profiles are consistent with those of Deardoff (1979) and Deardorff et al. (1980).

Chou, S.-H.↗

NASA NTRS1987

Energy diffusion of pickup ions upstream of comets

A steady state model of pickup ion energization upstream of a cometary bow wave is presented in order to investigate the effects of quasi-linear energy diffusion in the turbulence there. The model assumes that the ions are immediately isotropized at pickup, and it includes the effects of adiabatic acceleration in the slowing solar wind and of continual pickup of ions as the comet is approached. By taking all physical quantities to fall off as power laws with distance from the comet, an analytical expression is obtained for the distribution function of pickup ions in the reference frame moving with the solar wind. To illustrate the application of this model, the model results are compared to the observations of pickup ions at comet Giacobini-Zinner. At present, this is the only cometary encounter for which sufficient quantitative information is available. The model does not compare well with these observations, but it is not clear whether the differences are due to artificial problems in the model or the data analysis or to the action of other energization processes at this comet. Preliminary results from the Halley encounters appear to agree more closely with this model.

Isenberg, Philip A.↗

NASA NTRS1989

Far-infrared emission in the Rho Ophiuchi region - A comparison with molecular gas emission and visual extinction

The dust characteristics of a 40 arcmin x 40 arcmin section of the Rho Ophiuchi molecular clouds complex revealed by the IRAS satellite are compared with both molecular line and deep star count data for the region. The data reveal the cloud to be clearly visible at 12 and 25 microns, as well as at 60 and 100 microns. Modeling the infrared emission from the cloud as being due to two populations of dust grains, the short-wavelength emission is found not to reflect the internal structure of the molecular cloud. The 60 micron opacity determined using a single grain emission model correlates reasonably well with (C-13)O column density and visual extinction up to roughly 5 mag. The cloud edges appear to be heated by the interstellar radiation field. The far-infrared luminosity to mass ratio for the region is determined to be 0.9 solar luminosity/solar mass, a value much smaller than the average ratio for the inner Galaxy.

Jarrett, T. H.↗

NASA NTRS1992

Summary of ionizing radiation analysis on the Long Duration Exposure Facility

The ionizing radiation measurements flown on the Long Duration Exposure Facility (LDEF) were contained in 15 experiments which utilized passive detectors to pursue objectives in astrophysics and to measure the radiation environment and dosimetric quantities. The spacecraft structure became sufficiently radioactive to permit additional important studies. The induced activity allows extensive radiation mapping in the structure, and independent comparison with experiment dosimetric techniques, and significant studies of secondary effects. The long exposure time, attitude stability, and number and types of measurements produced a unique and critical set of data for low Earth orbit that will not be duplicated for more than a decade. The data allow an unprecedented test, and improvement if required, of models of the radiation environment and the radiation transport methods that are used to calculate the internal radiation and its effects in spacecraft. Results of measurements in the experiments, as well as from radioactivity in the structure, have clearly shown effects from the directional properties of the radiation environment, and progress was made in the dosimetric mapping of LDEF. These measurements have already influenced some Space Station Freedom design requirements. Preliminary results from experiments, reported at this symposium and in earlier papers, show that the 5.8 years exposure considerably enhanced the scientific return of the radiation measurements. The early results give confidence that the experiments will make significant advances in the knowledge of ultra heavy cosmic rays, anomalous cosmic rays, and heavy ions trapped in the radiation belts. Unexpected phenomena were observed, which require explanation. These include stopping iron group ions between the energy ranges anticipated for anomalous and galactic cosmic rays in the LDEF orbit. A surprising concentration of the Be-7 nuclide was discovered on the 'front' surface of LDEF, apparently transported up from the stratosphere with exceptional efficiency.

Parnell, T. A.↗

NASA NTRS1991

The impact of Mars surface characteristics on rover design

The characteristics of the surface of Mars will have a profound effect on the design and operation of roving vehicles. The design impacts of surface conditions, and the implications of knowing these conditions well or poorly, are described. It is a clear benefit to have orbital imaging, and radar subsurface sounding data at a scale of about one meter before designing the rover. In addition, knowledge of the terrain to one meter scale is important for efficient traverse and operations planning.

Pivirotto, Donna L. S.↗