Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wind integration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Application of Neural Networks to Wind tunnel Data Response Surface Methods

The integration of nonlinear neural network methods with conventional linear regression techniques is demonstrated for representative wind tunnel force balance data modeling. This work was motivated by a desire to formulate precision intervals for response surfaces produced by neural networks. Applications are demonstrated for representative wind tunnel data acquired at NASA Langley Research Center and the Arnold Engineering Development Center in Tullahoma, TN.

Lo, Ching F.↗
NASA NTRS1990

Comparison of model- and full-scale wind-tunnel performance

Experimental results from the Integrated Systems Test of the upgraded National Full-Scale Aerodynamics Complex 40- by 80-ft wind tunnel located at NASA Ames Research Center, which took place in 1987, are compared with results obtained with a 1/50 scale model of the wind tunnel. Test-section flow characteristics, air-exchange performance, total pressure distributions, and wall-static pressure distributions obtained with the model- and full-scale facilities are compared. The 1/50-scale model data were used to predict qualitative performance trends of the full-scale facility during investigation of design changes. Despite large differences in scale and Reynolds number between the two tunnels, quantitative agreement between certain model and full-scale performance characteristics was quite good.

Smith, Brian E.↗
DOE OSTI2020

IEA Wind TCP Task 37: Definition of the IEA 15-Megawatt Offshore Reference Wind Turbine

This report describes a 15-megawatt offshore wind turbine with a fixed-bottom monopile support structure. This reference wind turbine is a Class IB direct-drive machine, with a rotor diameter of 240 meters and a hub height of 150 meters. An overview of the design is presented in Figure ES-1 and Table ES-1. The design reflects a joint effort between the National Renewable Energy Laboratory, sponsored by the U.S. Department of Energy, and the Technical University of Denmark, sponsored by the European Union's H2020 Program, through the second work package of International Energy Agency Wind Task 37 on Wind Energy Systems Engineering: Integrated RD&D. A forthcoming report will detail a semisubmersible floating support structure developed by the University of Maine.

15 MW↗
NASA NTRS2004

Aeroheating Design Issues for Reusable Launch Vehicles: A Perspective

An overview of basic aeroheating design issues for Reusable Launch Vehicles (RLV), which addresses the application of hypersonic ground-based testing, and computational fluid dynamic (CFD) and engineering codes, is presented. Challenges inherent to the prediction of aeroheating environments required for the successful design of the RLV Thermal Protection System (TPS) are discussed in conjunction with the importance of employing appropriate experimental/computational tools. The impact of the information garnered by using these tools in the resulting analyses, ultimately enhancing the RLV TPS design is illustrated. A wide range of topics is presented in this overview; e.g. the impact of flow physics issues such as boundary-layer transition, including effects of distributed and discrete roughness, shockshock interactions, and flow separation/reattachment. Also, the benefit of integrating experimental and computational studies to gain an improved understanding of flow phenomena is illustrated. From computational studies, the effect of low-density conditions and of uncertainties in material surface properties on the computed heating rates are highlighted as well as the significant role of CFD in improving the Outer Mold Line (OML) definition to reduce aeroheating while maintaining aerodynamic performance. Appropriate selection of the TPS design trajectories and trajectory shaping to mitigate aeroheating levels and loads are discussed. Lastly, an illustration of an aeroheating design process is presented whereby data from hypersonic wind-tunnel tests are integrated with predictions from CFD codes and engineering methods to provide heating environments along an entry trajectory as required for TPS design.

Zoby, E. Vincent↗
NASA NTRS2004

Aeroheating Design Issues for Reusable Launch Vehicles: A Perspective

An overview of basic aeroheating design issues for Reusable Launch Vehicles (RLV), which addresses the application of hypersonic ground-based testing, and computational fluid dynamic (CFD) and engineering codes, is presented. Challenges inherent to the prediction of aeroheating environments required for the successful design of the RLV Thermal Protection System (TPS) are discussed in conjunction with the importance of employing appropriate experimental/computational tools. The impact of the information garnered by using these tools in the resulting analyses, ultimately enhancing the RLV TPS design is illustrated. A wide range of topics is presented in this overview; e.g. the impact of flow physics issues such as boundary-layer transition, including effects of distributed and discrete roughness, shock-shock interactions, and flow separation/reattachment. Also, the benefit of integrating experimental and computational studies to gain an improved understanding of flow phenomena is illustrated. From computational studies, the effect of low-density conditions and of uncertainties in material surface properties on the computed heating rates a r e highlighted as well as the significant role of CFD in improving the Outer Mold Line (OML) definition to reduce aeroheating while maintaining aerodynamic performance. Appropriate selection of the TPS design trajectories and trajectory shaping to mitigate aeroheating levels and loads are discussed. Lastly, an illustration of an aeroheating design process is presented whereby data from hypersonic wind-tunnel tests are integrated with predictions from CFD codes and engineering methods to provide heating environments along an entry trajectory as required for TPS design.

Zoby, E. Vincent↗
DOE OSTI2026

Operational Simulation of Multi-Functional Charging Station for Sustainable Transportation

As transportation systems move toward electrification and decarbonization, multifunctional charging stations (MFCS) are emerging as key infrastructure for electric vehicles (EVs) and hydrogen fuel cell vehicles (HFCVs). This paper presents a simulation model of an MFCS that integrates solar photovoltaic (PV), wind power, battery storage, hydrogen (\mathrm{H}_{2}) production, dual-pressure \mathrm{H}_{2} storage, fuel cells, and dynamic grid interactions. The model simulates daily operations using 5 -minute resolution data to capture realtime variability in renewable energy (RE), demand, and electricity prices. A flexible dispatch algorithm dynamically allocates energy for EV charging, \mathrm{H}_{2} production, storage, and grid transactions while respecting system constraints. Results show that the MFCS effectively prioritizes RE usage, minimizes waste, meets diverse energy demands, and achieves net operational profit. The model serves as a valuable decision-support tool for designing and optimizing integrated clean energy hubs for zero-emission transportation.

Gbadegoye, Jeremiah [University of Tennessee, Knox↗
NASA NTRS1974

Investigation of the association of magnetopause instability with interplanetary sector structure

The variation of the solar wind parameters (speed, magnetic field intensity, and proton density) and geomagnetic disturbance with location within the interplanetary sector structure is well established. The Kelvin-Helmholtz instability of the magnetopause provides a mechanism for the initiation of worldwide geomagnetic disturbance. Since the Kelvin-Helmholtz mechanism depends on an integration of several of the solar wind parameters, it was considered of interest to see how it varies within the sector structure. Support is given to the idea that the integration of the solar wind parameters via Kelvin-Helmholtz instability is an important concept in understanding geomagnetic disturbance.

Boller, B. R.↗
DOE OSTI2024

WIND Toolkit Long-Term Ensemble Dataset

WIND Toolkit Long-term Ensemble Dataset (WTK-LED), an updated version of the meteorological WIND Toolkit, is a meteorological dataset providing high-resolution time series, including interannual variability and model uncertainty of wind speed at every modeling grid point to indicate ranges of possible wind speeds. The data were produced using the Weather Research and Forecasting Model (WRF). The vertical grid used in WTK-LED includes many vertical layers in the atmospheric boundary layer to provide information of atmospheric quantities across the rotor layer of utility scale and distributed wind turbines. The WTK-LED includes: (1) Numerical simulations of wind speed and other meteorological variables covering the contiguous United States (CONUS) and Alaska, with high-resolution (5-minute [min], 2-kilometer [km]) data for 3 years (2018-2020): WTK-LED CONUS, WTK-LED Alaska. (2) Climate simulations from Argonne National Laboratory covering North America, including Alaska, Canada, and most of Mexico and the Caribbean islands. These simulations complement the new WTK-LED to offer a 4-km, hourly dataset covering 20 years (2001-2020): WTK-LED Climate. (3) Specific long-term, high-resolution offshore simulations have been conducted separately for the U.S. coasts, Hawaii, and the Great Lakes, leading to the 2023 National Offshore Wind dataset: NOW-23. The data for Hawaii include land-based data and are part of WTK-LED Hawaii. Because the accuracy of simulations from a mesoscale model, such as WRF, varies depending on the location and weather situation, and can reach up to several m/s for wind speed, we provide simulated wind speed uncertainty estimates to the community to be used in conjunction with the deterministic model simulations. This dataset was developed to satisfy a wide group of stakeholders across various wind energy disciplines, including but not limited to stakeholders in the distributed and utility scale wind industry, the new emerging airborne wind energy field, grid integration, power systems modeling, environmental modeling, and researchers in academia, and to close some of the gaps that current public datasets have. Based on our validation results to date, we suggest use cases and applications for each dataset of the WTK-LED as shown in "WTK-LED Use Cases" resource below.

Array↗
DOE OSTI2021

Cybersecurity Guide for Distributed Wind

Distributed wind sits at the intersection of grid-connected, off-grid and behind-the-meter cyber-physical electrical energy systems. The unique physical properties and communications requirements for distributed wind systems mean that there are unique cybersecurity considerations, but there is little to no existing guidance on best practices for cybersecurity. This document is intended to be a starting point for distributed wind stakeholders including manufacturers, installers and integrators, and operators (facility, aggregator, or utility). We discuss common distributed wind architectures and describe their role in the larger power system, pointing out some of the key connections to be aware of. Cybersecurity cannot exist in a vacuum, but rather must consider all the system and all its connections holistically. The role of distributed wind and the functions it can serve are described to gain understanding of the full range of capabilities. The purpose and application of relevant standards that may apply to certain distributed wind systems is presented. These standards may not apply to all installations, but even for systems that are not required to meet these standards they can be a good reference for best practices. A holistic threat perspective is used to describe the adversaries, threats, and potential impacts of cyberattacks, with special emphasis on what sets distributed wind systems apart from other distributed energy resources (DER). Finally, we present the recommendations for cybersecurity, both in terms of needs of the system and roles that specific stakeholders should fulfill. Distributed wind systems can come in a variety of architectures and applications, so there is no one-size-fits-all approach to cybersecurity. However, this document contains the relevant information for stakeholders to identify the cybersecurity needs of their system, refer to relevant standards, and apply best practices in a manner most consistent with their security and operational goals.

17 WIND ENERGY↗
NASA NTRS1982

Inversion of data from diffraction-limited multiwavelength remote sensors. II - Nonlinear dependence of observables on the geophysical parameters

Linear shift-invariant spatial filtering is applied to inversion of radiometric measurements of the earth in both polarizations at the following frequencies: 6.6, 10.7, 18, 21, and 37 GHz. For purposes of radiative transfer calculations at these frequencies, the state of the ocean-atmosphere system is described by a seven-parameter model. The parameters are near-surface wind speed, sea surface temperature, integrated water vapor mass, scale height of water vapor in an exponential distribution, integrated liquid water mass, height of the liquid water, and characteristic drop radius in a Best (1950) drop size distribution. Also described is a spatial filtering algorithm by means of which geophysical parameters are retrieved from measurements made over the ocean by the scanning multichannel microwave radiometer on the Nimbus 7 satellite. The parameters here are near-surface wind speed, sea surface temperature, rain rate, integrated atmospheric water vapor content, and integrated liquid water content (including rain).

Rosenkranz, P. W.↗
DOE OSTI2025

Global techno-economic and life cycle greenhouse gas emissions assessment of solar and wind based renewable hydrogen production

This study conducts a global assessment of renewable hydrogen production pathways, focusing on techno-economic performance and life cycle greenhouse gas (GHG) emissions. It evaluates standalone solar photovoltaic (PV), wind, and hybrid PV/wind systems, integrated with proton exchange membrane (PEM) electrolyzers, through multi-objective optimization and considering embodied emissions in manufacturing PV, wind and electrolyzers. Results identify optimal configurations to minimize levelized cost of hydrogen (LCOH) and carbon intensity (CI) of hydrogen, showing potential reductions of cost and CI by 2030. Standalone PV systems can achieve LCOH values smaller than 6.5 USD/kg H 2 and CI less than 2.5 kg CO 2 eq/kg H 2 in regions with high solar irradiance, such as North Africa, the Middle East and Chile. Wind systems in regions such as Middle East, North Africa, Australia and Central United States achieve LCOH below 5 USD/kg H 2 and CI under 1.5 kg CO 2 eq/kg H 2 . Hybrid systems emerge as the optimal solution for minimizing both the LCOH and CI by maximizing the use of renewable energy. Moreover, the results also indicate that, with the technological advancements, future reduction in the capital cost of renewable energy systems and the PEM electrolyzer as well as the trade of coproduct O 2 could drive the LCOH of all the RES-based hydrogen systems below 1 USD/kg H 2 and the CI below zero in different regions as Middle East, North Africa and Central United State

08 HYDROGEN↗
NASA NTRS1989

Line-of-sight effects on spectroscopic measurements in the inner solar wind region

The effect of the integration along the line of sight on the spectral line profiles of the resonantly scattered Lyman alpha radiation emitted by low-density coronal holes at heights above 1.5 Rs from sun center is investigated. It is shown how the spectral lines from this region are influenced by the Lyman alpha emission from surrounding regions with higher densities. The coronal hole and the surrounding areas are described by a two-fluid solar wind model. It is shown that the line-of-sight effects can be important for the interpretation of the Lyman alpha spectral line measurements in the outer corona and inner solar wind.

Esser, Ruth↗
DOE OSTI2023

High temporal resolution generation expansion planning for the clean energy transition

As power systems integrate increasing quantities of wind, solar and energy storage resources, it is important to revisit power system capacity expansion modeling methods and assumptions that have been utilized in thermal- dominated systems. We conduct a series of case study analyses using a simplified representation of the Electric Reliability Council of Texas (ERCOT) system to demonstrate how least-cost capacity expansion outcomes are impacted by changes in model resolution across two temporal dimensions: 1) the number of considered representative periods, and 2) the system dispatch interval. First, we find that the least-cost generation portfolio can differ significantly for small changes in the number of representative days, but largely converges to the 365-day result once 104 representative days are considered. Furthermore, systems with wind, solar and storage resources were more sensitive to changes in the number of representative days than a thermal-dominated system. Second, we find that considering five-minute dispatch resolution consistently results in least-cost generation portfolios with less solar capacity and more energy storage capacity than corresponding scenarios with hourly dispatch intervals. This suggests that hourly dispatch representation fails to capture the intra-hour volatility of solar generation, and therefore also overlooks opportunities for storage resources to provide system value by balancing this volatility. Collectively these results indicate that capacity expansion modelers should revisit conventional approaches to temporal representation when conducting analyses of deeply decarbonized power systems to ensure that such analyses are robust and actionable. To our knowledge, this is the first study to analyze capacity expansion outcomes with five-minute dispatch resolution in this manner.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Using a Grid-Forming Inverter to Stabilize a Low-Inertia Power System - Maui Hawaiian Island

As power systems around the world integrate greater amounts of wind and solar photovoltaic power, periods of very high instantaneous power shares of inverters, the primary interfacing technology for these generation sources, are complicating system stability and control. The contemporary, primary mode of inverter operation, grid-following, which explicitly assumes the presence of a local, stable voltage waveform, yields operational inadequacy at high instantaneous power shares potentially leading to instability due to the low-inertia conditions, as well as the correlated reduced voltage forming capacity on the respective system. Parallel connected grid-forming inverters, which directly regulate the local voltage, are a solution that is expected to bolster system stability and mitigate the shortcomings of the grid-following technology. In this paper, grid-following and two types of grid-forming inverter control, the traditional linear droop and the recently introduced nonlinear exponential droop (Droop-e), are simulated on a low-inertia, H = 0.48s, high inverter-based resource scenario, 97%, with a validated electromagentic transient domain model of the Hawaiian island of Maui power system. The benefit of a single grid-forming device over its grid-following counterpart is significant, both in terms frequency deviation and voltage stability. Further, the superiority of the Droop-e and the associated secondary power sharing control over both grid-following and linear droop grid-forming technologies is displayed, with improved nadir and rate of change of frequency over the linear droop control.

droop control↗
NASA NTRS1973

Design integration and noise studies for jet STOL aircraft. Task 7B: Wind tunnel investigation of a 14-percent-thick airfoil with upper surface blowing at high subsonic Mach numbers

An exploratory wind tunnel test has been conducted at Mach numbers from 0.60 to 0.80 to investigate the effects of nozzle geometry and upper surface blowing on the aerodynamic characteristics of a 14-percent-thick airfoil. Measured data included lift, drag, pitching moments, surface pressures, and nozzle thrust.

Mahal, A. S.↗
NASA NTRS1979

Bi-directional four quadrant (BDQ4) power converter development

The feasibility for implementation of a concept for direct ac/dc multikilowatt power conversion with bidirectional transfer of energy was investigated. A 10 kHz current carrier was derived directly from a common 60 Hz three phase power system. This carrier was modulated to remove the 360 Hz ripple, inherent in the three phase power supply and then demodulated and processed by a high frequency filter. The resulting dc power was then supplied to a load. The process was implemented without the use of low frequency transformers and filters. This power conversion processes was reversible and can operate in the four quadrants as viewed from any of the two of the converter's ports. Areas of application include: power systems on air and spacecraft; terrestrial traction; integration of solar and wind powered systems with utility networks; HVDC; asynchronous coupling of polyphase networks; heat treatment; industrial machine drives; and power supplies for any use including instrumentation.

Schwarz, F. C.↗
NASA NTRS1987

On the relationship between scatterometer-derived convergences and atmospheric moisture

Fields of divergence calculated from the Seasat-A Satellite Scatterometer winds and fields of integrated water vapor and rainrate from the Scanning Multichannel Microwave Radiometer on Seasat are constructed for three different midlatitude cyclones. These storms include an explosively deepening cyclone that occurred in the North Atlantic (also known as the Queen Elizabeth II cyclone), a storm that occurred in the North Pacific, and a Southern Ocean storm. In all three cases, the regions of convergence and atmospheric water (vapor and rain) are consistent with each other and help to define features of each storm. The vertical distribution of moisture is inferred for one case using both the convergence pattern and the integrated water vapor field. In another, interpretation of the convergence field in a data gap region is aided by the water vapor field. In all three cases, surface low pressure centers, fronts, and even frontal waves are clearly evident as areas of convergence, and increased water vapor and rainrate.

Mcmurdie, Lynn A.↗
NASA NTRS1990

Experimental studies of 90 deg corner cascades in the National Full-Scale Aerodynamic Complex

Two 90 deg, fixed geometry, turning vane cascades were replaced in the 40- by 80-foot wind tunnel circuit of the National Full-Scale Aerodynamic Complex as a part of a major facility upgrade. Prior to the replacement of these vanes, small-scale, two-dimensional tests were conducted to assess the aerodynamic performance of the original, 1930's technology vane geometry and a new vane geometry which was developed using a modern cascade design code. The small scale tests were conducted in the 1/10th-Scale Cascade Test Facility and included measurements of total pressure, static pressure, and flow angularity distributions in the wake of the cascade and static pressure distributions along the vane profiles. Test results and a detailed comparison of the two vanes designs are presented. Based on these results, the new design was chosen and subsequently installed in the wind tunnel. During the integrated systems test of the upgraded facility, two of the 52 vanes in the first cascade were instrumented near midspan. The full-scale test results are presented, these show the cascade pressure loss coefficient to be slightly larger than obtained in the small-scale tests. Elements of the three-dimensional flow field upstream of the cascade, which effect can impact cascade performance, are discussed and recommendations for future research are given.

Meyn, Larry A.↗