Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustic tones”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Noise of the 10-bladed 60 deg swept SR-5 propeller in a wind tunnel

Noise generated by supersonic helical tip speed propellers is a possible cabin environment problem for future airplanes powered by these propellers. Noise characteristics of one of these propellers, designated SR-5, are presented. A matrix of tests was conducted to provide as much acoustic information as possible. During aerodynamic testing it was discovered that the propeller had an aeroelastic instability which prevented testing the propeller at its design advance ratio of 4.08 at axial Mach numbers over 0.7. Plots of the variation of the maximum blade passage tone with helical tip Mach number indicate that, at higher helical tip Mach numbers, the propeller operated on sharply increasing portion of the noise curve; therefore, extrapolations to the design condition would not be accurate. A possible extrapolation indicated that SR-5 at its design point should be quieter than SR-3 at its design point. Directivity plots at the higher helical tip Mach numbers indicate a lobed directivity pattern as was observed previously on the SR-3 propeller.

Dittmar, J. H.↗
NASA NTRS1993

A numerical analysis of tonal acoustics in rotor-stator interactions

In this study, the unsteady, thin-layer, Navier-Stokes equations are solved using a system of patched grids for a rotor-stator configuration of an axial turbine. The study focuses on the plurality of spinning modes that are present in such an interaction. The propagation of these modes in the upstream and downstream regions is analyzed and compared with numerical results. It was found that the numerically calculated tonal acoustics could be affected by the type of numerical boundary conditions employed at the inlet and exit of the computational boundaries and the grid spacing in the upstream and downstream regions. Results in the form of surface pressure amplitudes and the spectra of turbine tones and their far field behavior are presented. Numerical results and experimental data are compared wherever possible. The 'mode-content' for different harmonics of blade-passage frequency is shown to conform with that predicted by a kinematical analysis.

Rangwalla, A. A.↗
NASA NTRS1976

Noise reduction from the redesign of a fan stage to minimize stator lift fluctuations

An existing fan stage, redesigned to reduce stator lift fluctuations, was acoustically tested for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator chord, adjusting incidence angles, and by adjusting the rotor velocity diagrams. The experiments showed significantly reduced broadband noise levels in the middle to high frequencies. Blade passage tone power was not reduced, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.

Dittmar, J. H.↗
NASA NTRS1976

Noise reduction from the redesign of a fan stage to minimize stator lift fluctuations

An existing fan stage, redesigned to reduce stator lift fluctuations, was acoustically tested for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator chord, adjusting incidence angles, and by adjusting the rotor velocity diagrams. The experiments showed significantly reduced broadband noise levels in the middle to high frequencies. Blade passage tone power was not reduced, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.

Dittmar, J. H.↗
NASA NTRS1978

Acoustic evaluation of a novel swept-rotor fan

Inlet noise and aerodynamic performance are presented for a high tip speed fan designed with rotor blade leading edge sweep that gives a subsonic component of inlet Mach number normal to the edge at all radii. The intent of the design was to minimize the generation of rotor leading edge shock waves thereby minimizing multiple pure tone noise. Sound power level and spectral comparisons are made with several high-speed fans of conventional design. Results show multiple pure tone noise at levels below those of some of the other fans and this noise was initiated at a higher tip speed. Aerodynamic performance of the fan did not meet design goals for this first build which applied conventional design procedures to the swept fan geometry.

Lucas, J. G.↗
NASA NTRS1978

Acoustic evaluation of a novel swept-rotor fan

Inlet noise and aerodynamic performance are presented for a high tip speed fan designed with rotor blade leading edge sweep that gives a subsonic component of inlet Mach number normal to the edge at all radii. The intent of the design was to minimize the generation of rotor leading edge shock waves thereby minimizing multiple pure tone noise. Sound power level and spectral comparisons are made with several high-speed fans of conventional design. Results showed multiple pure tone noise at levels below those of some of the other fans and this noise was initiated at a higher tip speed. Aerodynamic performance of the fan did not meet design goals for this first build which applied conventional design procedures to the swept fan geometry.

Lucas, J. G.↗
NASA NTRS1977

Noise of fan designed to reduce stator lift fluctuations

An existing fan stage was redesigned to reduce stator lift fluctuations and was acoustically tested at three nozzle sizes for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator cord, adjusting incidence angles, and adjusting the rotor velocity diagrams. Broadband noise levels were signficantly reduced in the middle to high frequencies. Blade passage tone sound power was not lessened, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.

Dittmar, J. H.↗
NASA NTRS1978

Acoustic measurements of a large cavity in a wind tunnel

Acoustic measurements were made with inside and far-field microphones. Correlation of measured frequencies with available theories indicates that existing theories are applicable over a broader range than previously shown. The cavity configuration with a partial covering downstream amplified tonal intensities. The frequency of the tones depended on cavity size, not on cavity open area. Introducing upstream disturbances decreased the amplitude of the cavity tones.

Scheiman, J.↗
NASA NTRS1994

Fluid-acoustic interactions in a low area ratio supersonic jet ejector

An experimental investigation carried out to determine aerodynamic and acoustic characteristics of a low area ratio rectangular jet ejector is reported. A supersonic primary jet issuing from a rectangular convergent-divergent nozzle of aspect ratio 4, into a rectangular duct of area ratio 3, was used. Improved performance was found when the ejector screech tone is most intense and appears to match the most unstable Strouhal number of the free rectangular jet. When the primary jet was operating at over and ideally expanded conditions, significant noise reduction was obtained with the ejector as compared to a corresponding free jet. Application of particle image velocimetry to high speed ejector flows was demonstrated through the measurement of instantaneous two dimensional velocity fields.

Krothapalli, Anjaneyulu↗
NASA NTRS1985

Tone excited jets. I - Introduction

The major objective of the present study is an understanding of the mechanism of broadband jet noise augmentation due to upstream excitation, in terms of the relationship between excitation characteristics, changes in large scale and/or small scale turbulence structure of the jet, and sound radiated to the far field under both static and simulated forward velocity conditions. A systematic set of acoustic measurements was accordingly made for a range of flow conditions in the acoustic research facilities of a large transport aircraft manufacturer. After analyzing acoustic results, turbulence measurements were made with a laser velocimeter for those jet conditions at which jet noise amplification was important. A theory was developed to account for static and in-flight simulation results.

Tanna, H. K.↗
NASA NTRS1991

Laboratory test and acoustic analysis of cabin treatment for propfan test assessment aircraft

An aircraft cabin acoustic enclosure, built in support of the Propfan Test Assessment (PTA) program, is described. Helmholtz resonators were attached to the cabin trim panels to increase the sidewall transmission loss (TL). Resonators (448) were located between the trim panels and fuselage shell. In addition, 152 resonators were placed between the enclosure and aircraft floors. The 600 resonators were each tuned to a 235 Hz resonance frequency. After flight testing on the PTA aircraft, the enclosure was tested in the Kelly Johnson R and D Center Acoustics Lab. Laboratory noise reduction (NR) test results are discussed. The enclosure was placed in a Gulfstream 2 fuselage section. Broadband (138 dB overall SPL) and tonal (149 dB overall SPL) excitations were used in the lab. Tonal excitation simulated the propfan flight test excitation. The fundamental tone was stepped in 2 Hz intervals from 225 through 245 Hz. The resonators increase the NR of the cabin walls around the resonance frequency of the resonator array. The effects of flanking, sidewall absorption, cabin adsorption, resonator loading of trim panels, and panel vibrations are presented. Increases in NR of up to 11 dB were measured.

Kuntz, H. L.↗
NASA NTRS1981

Assessment of inflow control structure effectiveness and design system development

Inflow control structures used during static testing of fans are shown to minimize inflow distortions and thus stimulate the inflight flow field and noise generating mechanisms. Acoustic tests are conducted on a Pratt and Whitney aircraft JT9D engine with and without an inflow control structure. Raw data are corrected to 77 deg, and time is averaged over 0.5 second intervals. Use of an inflow control structure is found to significantly reduce blade passage frequency tone, while having little effect on twice blade passage frequency tones, and significantly improves agreement between static data projected to flight and flight data for the blade passage frequency fan tone. A design system is also presented, which prescribes structure shape, size and construction.

Peracchio, A. A.↗
NASA NTRS1986

Advanced turboprop aircraft noise annoyance - A review of recent NASA research

Passenger and community response to advanced turboprop aircraft noise are studied. Four experiments were conducted utilizing an aircraft noise synthesis system, an exterior effects room, an anechoic listening room, and a Space Station/aircraft acoustic apparatus; the experimental conditions and procedures for the psychoacoustic studies are described. The community noise studies involved evaluating the effects of various tonal characteristics on annoyance. It was observed that the frequency envelope shape did not effect annoyance; however, the interaction of the fundamental frequency with tone-to-broadband noise ratio did have a large effect on annoyance. The effects of low frequency tones, turbulent boundary layer noise, and tonal beats on passenger annoyance are investigated. The data reveal that passenger annoyance is greater for a given level of boundary layer noise when tones are at levels sufficient to increase the overall sound pressure level within the cabin. The annoyance response of an advanced turboprop and a conventional aircraft are compared. It is determined that the flyover noise level for the turboprop aircraft is not more annoying than that of a conventional aircraft.

Mccurdy, D. A.↗
NASA NTRS1999

TFaNS Tone Fan Noise Design/Prediction System: System Description, CUP3D Technical Documentation and Manual for Code Developers - Volume 1

TFaNS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFaNS consists of: The codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. Cup3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report provides technical background for TFaNS including the organization of the system and CUP3D technical documentation. This document also provides information for code developers who must write Acoustic Property Files in the CUP3D format. This report is divided into three volumes: Volume I: System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume II: User's Manual, TFaNS Vers. 1.4; Volume III: Evaluation of System Codes.

Topol, David A.↗
NASA NTRS1999

TFaNS Tone Fan Noise Design/Prediction System: User's Manual - Volume 2

TFaNS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFaNS consists of: the codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. CUP3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report provides information on code input and file structure essential for potential users of TFANS. This report is divided into three volumes: Volume 1. System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume 2. User's Manual, TFANS Vers. 1.4; Volume 3. Evaluation of System Codes.

Topol, David A.↗
NASA NTRS1999

TFaNS Tone Fan Noise Design/Prediction System: Evaluation of System Codes - Volume 3

TFANS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFANS consists of: The codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. Cup3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report evaluates TFANS versus full-scale and ADP 22" fig data using the semi-empirical wake modelling in the system. This report is divided into three volumes: Volume 1: System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume II: User's Manual, TFANS Version 1.4; Volume III: Evaluation of System Codes.

Topol, David A.↗
NASA NTRS1980

Forward acoustic performance of a shock-swallowing high-tip-speed fan (QF-13)

Forward noise and overall aerodynamic performance data are presented for a high-tip-speed fan having rotor blade airfoils designed to alter the conventional leading-edge bow shocks to weak, oblique shocks which are swallowed within the interblade channels. It was anticipated that the swallowed shocks would minimize the generation of multiple-pure-tone noise. In the speed range where the shocks presumably were swallowed, the multiple-tone noise was lowered only about 3 decibels. Comparison with several high-speed fans on a thrust-corrected basis indicates that the present fan was the quietest in total forward noise at low speeds but offered no advantage at high speeds.

Lucas, J. G.↗
NASA NTRS1982

Analysis of combustion spectra containing organ pipe tone by cepstral techniques

Signal reinforcements and cancellations due to standing waves may distort constant bandwidth combustion spectra. Cepstral techniques previously applied to the ground reflection echo problem are used to obtain smooth broadband data and information on combustion noise propagation. Internal fluctuating pressure measurements made using a J47 combustor attached to a 6.44 m long duct are analyzed. Measurements made with Jet A and hydrogen fuels are compared. The acoustic power levels inferred from the measurements are presented for a range of low heat release rate operating conditions near atmospheric pressure. For these cases, the variation with operating condition of the overall acoustic broadband power level for both hydrogen and Jet A fuels is consistent with previous results showing it was proportional to the square of the heat release rate. However, the overall acoustic broadband power level generally is greater for hydrogen than for Jet A.

Miles, J. H.↗