Search NASA⌕ Search

SEARCH · Search NASA

Results for “addition reactions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Solid‐State Reaction Heterogeneity During Calcination of Lithium‐Ion Battery Cathode

Abstract During solid‐state calcination, with increasing temperature, materials undergo complex phase transitions with heterogeneous solid‐state reactions and mass transport. Precise control of the calcination chemistry is therefore crucial for synthesizing state‐of‐the‐art Ni‐rich layered oxides (LiNi 1‐x‐y Co x Mn y O 2 , NRNCM) as cathode materials for lithium‐ion batteries. Although the battery performance depends on the chemical heterogeneity during NRNCM calcination, it has not yet been elucidated. Herein, through synchrotron‐based X‐ray, mass spectrometry microscopy, and structural analyses, it is revealed that the temperature‐dependent reaction kinetics, the diffusivity of solid‐state lithium sources, and the ambient oxygen control the local chemical compositions of the reaction intermediates within a calcined particle. Additionally, it is found that the variations in the reducing power of the transition metals (i.e., Ni, Co, and Mn) determine the local structures at the nanoscale. The investigation of the reaction mechanism via imaging analysis provides valuable information for tuning the calcination chemistry and developing high‐energy/power density lithium‐ion batteries.

Chemistry↗
DOE OSTI2021

Bond dissociation energies of low-valent lanthanide hydroxides: lower limits from ion–molecule reactions and comparisons with fluorides

Despite that bond dissociation energies (BDEs) are among the most fundamental and relevant chemical properties they remain poorly characterized for most elementary lanthanide hydroxides and halides. Lanthanide ions Ln + = Eu + , Tm + and Yb + are here shown to react with H 2 O to yield hydroxides LnOH + . Additionally, under low-energy conditions such reactions must be exothermic, which implies a lower limit of 499 kJ mol -1 for the Ln + –OH BDEs. This limit is significantly higher than previously reported for YbOH + and is unexpectedly similar to the BDE for Yb + –F. To explain this apparent anomaly, it is considered feasible that the inefficient hydrolysis reactions observed here in a quadrupole ion trap mass spectrometer may actually be endothermic. More definitive and broad-based evaluations and comparisons require additional and more reliable BDEs and ionization energies for key lanthanide molecules, and/or energies for ligand-exchange reactions like LnF + OH ↔ LnOH + F. The hydroxide results motivated an assessment of currently available lanthanide monohalide BDEs. Among several intriguing relationships is the distinctively higher BDE for neutral LuF versus cationic LuF + , though quantifying this comparison awaits a more accurate value for the anomalously high ionization energy of LuF.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Pressure Driven Alkane Dehydrogenation by Palladium Metal

Abstract Dehydrogenation of alkanes is of increasing importance in fulfilling global demand for olefins and offers a potential source of carbon‐neutral hydrogen as a co‐product. Currently commercial dehydrogenation processes occur at high‐temperatures (500–900 °C) which is energy intensive and results in side reactions and rapid coking of the catalysts. In addition, the hydrogen produced is often burned to maintain temperature and to inhibit the back reaction. Here, pressure is utilized as a parameter to enable novel chemical catalytic processes, and ambient‐temperature dehydrogenation of alkanes by palladium is observed at 50–100 MPa, with both hydrogen gas and olefins recovered on decompression. This reaction follows a fundamentally different path to current commercial high‐temperature low‐pressure dehydrogenation processes with the palladium catalyst reversibly forming a hydride intermediate.

08 HYDROGEN↗
DOE OSTI2021

Parallels between enzyme catalysis, electrocatalysis, and photoelectrosynthesis

Catalysts are central to accelerating chemistry in biology and technology. In biochemistry, the relationship between the velocity of an enzymatic reaction and the concentration of chemical substrates is described via the Michaelis-Menten model. Additionally, the modeling and benchmarking of synthetic molecular electrocatalysts are also well developed. However, such efforts have not been as rigorously extended to photoelectrosynthetic reactions, where, in addition to chemical substrates and charge carriers, light is a required reagent. In this perspective, we draw parallels between concepts involving enzyme catalytic efficiency, the benchmarking of molecular electrocatalysts, and the performance of photoelectrosynthetic assemblies, while highlighting key differences, assumptions, and limitations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

IAEA Photonuclear Data Library 2019

Here, photo-induced reaction cross section data are of importance for a variety of current or emerging applications, such as radiation shielding design and radiation transport analyses, calculations of absorbed dose in the human body during radiotherapy, physics and technology of fission reactors (influence of photo-reactions on neutron balance) and fusion reactors (plasma diagnostics and shielding), activation analyses, safeguards and inspection technologies, nuclear waste transmutation, medical isotope production and astrophysical applications. To address these data needs the IAEA Photonuclear Data library was produced in 1999, containing evaluated photo-induced cross sections and neutron spectra for 164 nuclides which were deemed relevant for the applications. Since the release of the IAEA Photonuclear Data Library however, new experimental data as well as new methods to assess the reliability of experimental cross sections have become available. Theoretical models and input parameters used to evaluate photo-induced reactions have improved significantly over the years. In addition, new measurements of partial photoneutron cross sections using mono-energetic photon beams and advanced neutron detection systems have been performed allowing for the validation of the evaluations and assessments of the experimental data. Furthermore, technological advances have led to the construction of new and more powerful gamma-beam facilities, therefore new data needs are emerging. We report our coordinated efforts to address these data needs and present the results of the new up-to-date evaluations included in the new updated IAEA Photonuclear Data Library consisting of 219 nuclides. The new library includes 188 new evaluations produced by the CRP evaluators, and one evaluation taken from the JENDL/PD-2016 library, while 20 evaluations were retained from the previous 1999 IAEA Photonuclear Data Library. In most of the cases, the photon energy goes up to 200 MeV. A total of 55 nuclides are new in this library reflecting the progress in measurements but also the developing data needs. In this paper we discuss the new assessment method and make recommendations to the user community in cases where the experimental data are discrepant and the assessments disagree. In addition, in the absence of experimental data, we present model predictions for photo-induced reaction cross section on nuclides of potential interest to medical radioisotope production.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Monoterpene Photooxidation in a Continuous-Flow Chamber: SOA Yields and Impacts of Oxidants, NO x , and VOC Precursors

We report monoterpene photooxidation plays an important role in secondary organic aerosol (SOA) formation in the atmosphere. The low-volatility products can enhance new particle formation and particle growth, and thus have influences on climate feedbacks. Here, we present the results of α-pinene and Δ-3-carene photooxidation experiments conducted in continuous-flow mode in an environmental chamber under several reaction conditions. The roles of oxidants, addition of NO, and VOC molecular structure in influencing SOA yield are illustrated. SOA yield from α-pinene photooxidation shows a weak dependence on H 2 O 2 concentration, which is a proxy for HO 2 concentration. The high O/C ratios observed in the a-pinene photooxidation products suggest the production of highly oxygenated organic molecules (HOM). Addition of ozone to the chamber during low-NO x photooxidation experiments leads to higher SOA yield. With the addition of NO, the production of N-containing HOMs is enhanced and the SOA yield shows a modest, non-linear dependence on input NO concentration. Carene photooxidation leads to higher SOA yield than α-pinene under similar reaction conditions, which agrees with the lower volatility retrieved from evaporation kinetics experiments. These results improve the understanding of SOA formation from monoterpene photooxidation and could be applied to refine the representation of biogenic SOA formation in models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

An uncertainty-aware strategy for plasma mechanism reduction with directed weighted graphs

In this work, we present a framework for the analysis and reduction of plasma mechanisms by means of weighted directed graphs, in which reactions and species are both treated as nodes. The methodology consists of two distinct analyses. The first, which is qualitative, relies on graph spatializations via force-directed algorithms to discover the predominant global patterns in the chemical model. The second ranks the reactions based on their shortest paths' lengths from/to the species of interest and their relative contributions to the power balance. Further, this quantitative investigation enables a strategy for mechanism reduction that is fully automatized, as it does not require any expert knowledge, highly effective, as it generates reduced mechanisms that are highly accurate while relying on a small number of processes, and easily interpretable, as the algorithm justifies the importance of the retained reactions by outputting their related chemical pathways. Additionally, the work proposes a methodology extension that employs ensembles of graphs to improve the robustness of the reduced mechanism to reaction parameter uncertainties. The approach, here tested for steady-state predictions of a plasma system characterizing negative hydrogen ion sources, is general and can be used in a wide variety of applications outside the particular nuclear fusion context demonstrated in this work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A combined experimental and computational study on the reaction dynamics of the 1-propynyl (CH 3 CC, X 2 A 1 ) – propylene (CH 3 CHCH 2 , X 1 A') system: formation of 1,3-dimethylvinylacetylene (CH 3 CCCHCHCH 3 , X 1 A') under single collision conditions

The reaction of the 1-propynyl radical (CH 3 CC; X 2 A 1 ) with propylene (CH 3 CHCH 2 ; X 1 A') was studied in a crossed molecular beam machine at a collision energy of 37 ± 1 kJ mol –1 . Experimental data combined with high-level electronic structure (CCSD(T)-F12/cc-pVTZ-F12//ωB97X-D/6-311G(d,p)) and RRKM calculations reveal the reaction mechanism. Here, the overall barrierless and exoergic reaction involves indirect reaction dynamics and commences preferentially with addition of 1-propynyl with its radical centre to the carbon–carbon double bond at the terminal carbon atom of propylene. This work focuses on molecular mass growth process (hydrogen loss channels) although theory suggests methyl loss as a prevalent channel. In these processes, the C6H9 collision complexes either emit atomic hydrogen or undergo isomerisation followed by atomic hydrogen loss to preferentially yield the cis/trans isomers of 1,3-dimethylvinylacetylene (2-hexen-4-yne) as the primary product. Analysis of reaction dynamics of 1-propynyl and ethynyl radicals with propylene along with their fractional abundance in deep space suggests formation of methyl- and dimethyl derivatives of vinylacetylene in cold molecular clouds. Once formed they may engage in fundamental molecular mass growth processes via the barrierless Hydrogen Abstraction Vinylacetylene Addition mechanism that leads to the formation of methyl- and dimethylnaphthalenes thus providing a versatile route to methyl-substituted PAHs in interstellar medium.

1-propynyl↗
DOE OSTI2020

Improved Performance of Cu(InGa)(SeS) 2 PV Modules Using the Reaction of Metal Precursors. Final Report

This project “Improved Performance of Cu(InGa)(SeS) 2 PV Modules using the Reaction of Metal Precursors” was a partnership led by the Institute of Energy Conversion (IEC) at the University of Delaware with Columbia University and the Molecular Foundry at the Lawrence Berkeley National Laboratory. The aim was to develop pathways to improve Cu(InGa)(SeS) 2 (CIGSS) thin film photovoltaic modules using processes compatible with low manufacturing cost. The CIGSS approach investigated was a two-step process including deposition of metal precursor films following by reaction in hydride gases utilizing IEC’s novel reactor. The process was similar to that under commercial development by the project’s industry partner Stion. When Stion went out of business mid-project the focus changed to a rapid thermal process considered more commercially viable. Approaches to improve the performance of solar cells using the reacted films focused on two material innovations. First, the overall Ga content was increased to increase the operating voltage, which is desirable for scale-up to commercial modules. Second, the processing and performance advantages arising from Ag alloying were investigated. Advanced characterization guided process and material development including control of relative composition gradients. Research on the formation of Cu-Ga-In metal precursors utilized sputtering deposition which is normally used in commercial applications. The work resulted in processes for deposition of precursor stacks with increased relative Ga content and effects of deposition parameters on morphology and phase composition were established. It was shown that the metal precursor films have comparable phase composition and morphology so subsequent reaction follows from the same starting point. The addition of Ag to the metal precursors gave more uniform morphology and improved adhesion of reacted films which enable higher reaction temperature for faster processing. A novel outcome was the discovery of a previously undocumented material phase in sputter-deposited and evaporated Ag-Cu-In-Ga thin films. Hydride gas reaction processes including time-temperature-concentration profiles were developed for different precursor compositions. This enables control of composition profiles to engineer through-film gradients for solar cell optimization with characterization and simulations used to correlate measured film composition profiles to measurements of devices. In particular, the gradient of sulfur at the front of the CIGSS film was found to be critical. The simulations guided process development leading to improved reproducibility of devices improved performance with higher Ga content and higher voltage. With Ag-alloyed precursors, the reaction pathways leading were determined. A significant finding was that Ag-alloying increases the reaction rate to completely convert precursor films to the final chalcopyrite which could enable reduced reaction time to benefit manufacturability. To maintain potential commercial viability, the process under investigation was refocused to a rapid thermal process that could potentially be incorporated into an in-line process for manufacturing. Precursors with different composition were capped with an extra selenium layer and reacted in hydrogen sulfide 5-15 minutes, compared to typically 2 hours in the previous multi-step batch process. Critical RTP parameters were identified to control the reaction. Further optimization would be needed for high efficiency solar cells but pathways to high quality devices with further optimization and improved heating uniformity were developed. The project also developed new optoelectronic characterization approaches with a focus on development and application of spatial- and time-resolved photoluminescence and a custom mapping photoluminescence microscope built. It was shown how critical electronic transport properties strongly depend on the chemical composition of the material and that a wide range of samples show inhomogeneity on a length scale larger than the grains in the films. Additionally, two-photon excitation capability was developed to distinguish bulk vs surface losses. The project advances the state-of-the -art for precursor reaction processes in several ways that could impact manufacturing. This includes validation of approaches to increase voltage and establishment of model-guided control to form optimal composition profiles. The application of process control approaches with knowledge of phase formation and reaction pathways can be critically valuable in designing a large-scale process.

14 SOLAR ENERGY↗
DOE OSTI2024

NO formation by N 2 /O 2 plasma catalysis: The impact of surface reactions, gas-phase reactions, and mass transport

Pathways and timescales relevant to facilitate plasma-assisted N 2 -O 2 reactions are assessed by measuring the consumption of plasma-derived N and the formation of NO in the gas phase and over Ag catalytic surfaces. These measurements are enabled by a setup that enables N 2 activation in an atmospheric pressure RF plasma jet, enables O 2 addition in the plasma afterglow, facilitates reactions over an Ag wire catalyst, and allows species density quantification by molecular beam mass spectrometry. Gas-phase reactions consume N but do not form NO with high selectivity. The presence of the non-porous Ag wire catalyst increases the rate of N conversion to NO, though mass transfer processes, not surface reactions, dictate the rate of N consumption. When O 2 concentrations and the ratio of the surface area of the catalyst to the void volume of the reactor are high (3–5 mol% O 2 , 10900 m –1 ), N conversion to NO reaches 100 % selectivity. When both N 2 and O 2 are fed through the plasma jet, gas-phase NO production increases 10×, although plasma and gas-phase processes do not exclusively produce NO. Above a threshold NO density, N cannot diffuse to the catalyst surface faster than it is consumed in the gas phase by reactions with NO. Furthermore, the use of heterogeneous catalysts to enhance plasma-driven N x O y formation and control N x O y product selectivity is limited to cases where diffusive transport of N from the gas phase to the catalyst surface is faster than consumption of N from gas-phase reactions with NO.

Engineering↗
DOE OSTI2022

Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides

To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS 2 ), here we report studies of the reactions of molybdenum hexafluoride (MoF 6 ) and hydrogen sulfide (H 2 S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF 6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ~13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS 2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. Finally, these results provide an improved understanding of MoS 2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS 2 toward integration into device manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Critical Role of Reductive Steps in the Nickel-Catalyzed Hydrogenolysis and Hydrolysis of Aryl Ether C-O Bonds

Hydrogenolysis of the aromatic C-O bond in aryl ethers is catalyzed by Ni in decalin or water at 150 °C. Observations of a significant kinetic isotope effect (kH/kD = 5.7) for the reactions of diphenyl ether under H2 and D2 and a positive dependence of the rate on H2 chemical potential in decalin indicate that addition of H to the aromatic ring is the rate-limiting step rather than C-O scission. Hydrogen addition occurs on the metal before C-O bond scission. DFT calculations indicate that hydrogen atom addition to the ortho position followed by C-O scission is energetically more feasible than C-O scission followed by H addition to either phenoxyl or phenyl moieties. Hydrogenolysis initiated via H addition in water is more selective (~75 %) compared to reactions in decalin (~30 %). The high selectivity for hydrogenolysis is attributed to stabilization of polar transition state by water as a polar solvent.

Wang, Meng↗
DOE OSTI2025

Nature of the Reactive Biferric Peroxy Intermediate P′ in the Arylamine Oxygenases and Related Binuclear Fe Enzymes

Binuclear nonheme iron enzymes activate O 2 to perform a wide range of chemical transformations. The process of O 2 activation typically involves a biferric peroxy-level intermediate P. It has been previously found that this intermediate undergoes further activation, either protonation or rearrangement to form P′ or further oxidation to form high-valent intermediates Q or X. Here, this study defines the structure of the P′ intermediate in the N-oxygenases CmlI (and AurF based on previous data) using nuclear resonance vibrational spectroscopy (NRVS) in conjugation with density functional theory (DFT) calculations. These results, combined with variable temperature variable field (VTVH) magnetic circular dichroism (MCD) spectroscopy on the 1-electron cryoreduced P′, define the structure of the P′ intermediate as a μ-1,2-hydroxoperoxo biferric site with a second hydroxide bridge. Reaction coordinate calculations demonstrate that single electron transfer (SET) is facilitated by protonation of the peroxo, activating its reductive cleavage, and that the additional hydroxide bridge does not impact this reaction. VTVH MCD studies further reveal that the hydroxide bridge is absent in the biferrous site, suggesting that during the O 2 reaction with the biferrous site, a water molecule forms the hydroxide bridge in providing the proton that activates the peroxide in P′ for reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Releasing chemical energy in spatiallyprogrammed ferroelectrics

Chemical energy ferroelectrics are generally solid macromolecules showing spontaneous polarization and chemical bonding energy. These materials still suffer drawbacks, including the limited control of energy release rate, and thermal decomposition energy well below total chemical energy. To overcome these drawbacks, we report the integrated molecular ferroelectric and energetic material from machine learning-directed additive manufacturing coupled with the ice-templating assembly. The resultant aligned porous architecture shows a low density of 0.35 g cm -3 , polarization-controlled energy release, and an anisotropic thermal conductivity ratio of 15. Thermal analysis suggests that the chlorine radicals react with macromolecules enabling a large exothermic enthalpy of reaction (6180 kJ kg -1 ). In addition, the estimated detonation velocity of molecular ferroelectrics can be tuned from 6.69 ± 0.21 to 7.79 ± 0.25 km s -1 by switching the polarization state. These results provide a pathway toward spatially programmed energetic ferroelectrics for controlled energy release rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impact of Electrolyte Additives on the Lifetime of High Voltage NMC Lithium-Ion Pouch Cells

This work involves improving the lifetime of lithium-ion cells during high voltage cycling using electrolyte additives. Three generations of electrolyte additives were investigated and screened in NMC442/graphite pouch cells using a 24 h voltage-hold protocol at 40 degrees C to accelerate oxidative reactions occurring at 4.4 V. Once promising additives and combinations were identified, they were then tested in cobalt-free NMC640/graphite cells for long-term cycling to upper cutoff voltages of 4.3, 4.4, and 4.5 V at temperatures of 20, 40, and 55 degrees C. Degradation mechanisms were probed using dV/dQ analysis, micro-X-ray fluorescence spectroscopy, and electrochemical impedance spectroscopy. The primary failure mode of cells held at high voltages is due to increase in cell impedance, which is correlated to the dissolution of transition metals, specifically manganese, originating from the positive electrode. We believe this dissolution is presumably due to the formation of a high impedance rock salt surface layer on the NMC positive electrode particles. Such deleterious outcomes can be limited by selecting an appropriate electrolyte additive package. It is hoped that this paper can provide a starting point for developing NMC Li-ion cells that can operate to voltages as high as 4.4 V and still display long lifetimes.

Azam, Saad↗
DOE OSTI2026

Nuclear Data Impact Assessment for the HTR-10 Pebble-Bed Reactor Using SCALE

The HTR-10 was used as a representative pebble-bed high-temperature gas-cooled reactor in this assessment of nuclear data’s impact on important reactor and spent fuel metrics, including safety-related quantities such as the effective multiplication factor (k eff ), temperature reactivity feedback, spent fuel inventory, and decay heat. Using the SCALE code system tools and ENDF/B-VII.1 nuclear data libraries, we quantify the effect of nuclear data uncertainties on these key performance metrics for both fresh fuel and equilibrium core configurations. For reactor core key parameters, important contributors to uncertainty include reactions of 235 U [$\bar{v}$, fission, (n, γ)], 238 U [elastic, (n, γ)], and graphite [elastic, (n, γ)]. Additional important contributors for the equilibrium core include reactions of higher actinides ( 239 Pu, 240 Pu) and fission products ( 135 Xe, 149 Sm). For spent fuel analysis, most nuclide inventory uncertainties remain below 5%. Higher uncertainties up to 11% are being observed for minor actinides like 243 Am and 244 Cm. Additionally, fission product uncertainties in 155 Eu and 155 Gd, of 25% and 23% respectively, are also significant and have implications for burnup credit applications. 110m Ag also shows high uncertainty of up to 11%, mainly due to fission product yield uncertainties. Decay heat relative uncertainties remain below 0.6% up to 10 years’ cooling time after fuel discharge. The highest relative uncertainty of 1.5% occurs at 500 years of cooling; however, because the decay heat value is very low at that time, the absolute uncertainty is not significant. This work demonstrates that extending assessments beyond fresh fuel k eff to include irradiated cores, nuclide inventories, and decay heat is essential in understanding the behavior of uncertainties as a function of fuel burnup and can support improvements of safety margins and spent fuel management.

Nuclear data impact↗
DOE OSTI2023

Probing O 2 -dependence of tetrahydrofuranyl reactions via isomer-resolved speciation

Low-temperature oxidation of tetrahydrofuran involves competing reactions that depend on temperature, pressure, and oxygen concentration, including ring-opening and subsequent oxidation of initial radicals ($\dot{R}$), HOO-elimination yielding dihydrofuran isomers, and the formation of peroxy radicals ($RO\dot{O}$). Here, the latter species, upon isomerization, lead to hydroperoxy-substituted radicals ($\dot{Q}OOH$) that undergo reaction either via unimolecular decomposition or second-O 2 -addition. Quantitative measurements of partially oxidized intermediates formed from each type of reaction provide critical constraints that are required for accurate modeling of combustion. To examine the influence of temperature and oxygen concentration on intermediates from tetrahydrofuran, isomer-resolved speciation measurements were conducted at 810 Torr in a jet-stirred reactor (JSR) from 500 – 1000 K. Resulting from negative-temperature coefficient behavior, species concentrations peaked at two temperatures, 600 K and 800 K, which were then selected for separate experiments to quantify O 2 -dependence using concentrations of 0.37 • 10 18 – 7.40 • 10 18 molecules cm –3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Critical Contribution of Imbalanced Charge Loss to Performance Deterioration of Si-Based Lithium-Ion Cells during Calendar Aging

Increasing the energy density of lithium-ion batteries, and thereby reducing costs, is a major target for industry and academic research. One of the best opportunities is to replace the traditional graphite anode with a high-capacity anode material, such as silicon. However, Si-based lithium-ion batteries have been widely reported to suffer from a limited calendar life for automobile applications. Heretofore, there lacks a fundamental understanding of calendar aging for rationally developing mitigation strategies. Both open-circuit voltage and voltage-hold aging protocols were utilized to characterize the aging behavior of Si-based cells. Particularly, a high-precision leakage current measurement was applied to quantitatively measure the rate of parasitic reactions at the electrode/electrolyte interface. The rate of parasitic reactions at the Si anode was found 5 times and 15 times faster than those of LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiFePO 4 cathodes, respectively. Here, the imbalanced charge loss from parasitic reactions plays a critical role in exacerbating performance deterioration. In addition, a linear relationship between capacity loss and charge consumption from parasitic reactions provides fundamental support to assess calendar life through voltage-hold tests. These new findings imply that longer calendar life can be achieved by suppressing parasitic reactions at the Si anode to balance charge consumption during calendar aging.

25 ENERGY STORAGE↗