Search NASA⌕ Search

SEARCH · Search NASA

Results for “analytical method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Cold air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing edge slot geometries. 2: Comparison of experimental and analytical results

Experimentally determined efficiencies of turbine stator blades having trailing-edge coolant ejection are compared with efficiencies predicted from two previously published approximate analytical methods. The experimental results were obtained from two-dimensional data with the temperature of the primary and coolant flows both being nearly ambient. Data from five stator blade configurations having different slotted trailing-edge geometries were included in the comparison. The two analytical methods gave results which agreed reasonably well with experimental results. An average of the absolute values of differences between experimental and predicted efficiencies for all five blade configurations showed that one method gave average efficiency differences which were about 1.3 percent different than experimental efficiencies, while the other method gave average efficiency differences that were about 0.7 percent different than experimental. However, in some instances, maximum differences of as much as 4 percent occurred. A comparison between experimental and analytical results indicated that the ratio of trailing-edge slot width to trailing-edge thickness influences the measured efficiencies to a greater extent than is accounted for by either analytical model.

Prust, H. W., Jr.↗

Characterization of spacecraft humidity condensate

When construction of Space Station Freedom reaches the Permanent Manned Capability (PMC) stage, the Water Recovery and Management Subsystem will be fully operational such that (distilled) urine, spent hygiene water, and humidity condensate will be reclaimed to provide water of potable quality. The reclamation technologies currently baselined to process these waste waters include adsorption, ion exchange, catalytic oxidation, and disinfection. To ensure that the baseline technologies will be able to effectively remove those compounds presenting a health risk to the crew, the National Research Council has recommended that additional information be gathered on specific contaminants in waste waters representative of those to be encountered on the Space Station. With the application of new analytical methods and the analysis of waste water samples more representative of the Space Station environment, advances in the identification of the specific contaminants continue to be made. Efforts by the Water and Food Analytical Laboratory at JSC were successful in enlarging the database of contaminants in humidity condensate. These efforts have not only included the chemical characterization of condensate generated during ground-based studies, but most significantly the characterization of cabin and Spacelab condensate generated during Shuttle missions. The analytical results presented in this paper will be used to show how the composition of condensate varies amongst enclosed environments and thus the importance of collecting condensate from an environment close to that of the proposed Space Station. Although advances were made in the characterization of space condensate, complete characterization, particularly of the organics, requires further development of analytical methods.

Muckle, Susan↗

Characterizing Radiation-Induced Chromium Redox Chemistry

The redox behavior of Cr(III) and Cr(VI) in nuclear environments were studied by analyzing aqueous irradiated chromium ions using UV-Visible spectroscopy. The formation of different chromium oxidation states can occur through gamma radiolysis of chromium solutions. Characterization of radiation-induced chromium is not well understood, and yet important as chromium can make its way into the primary coolant of reactors because of the corrosion of stainless steel reactor components. Furthermore, Cr(VI) is toxic and not suitable for environmental release, therefore Cr speciation is important. Fricke dosimetry was performed to collect doses rates, specific extinction coefficients were obtained from various analytical methods for the two oxidation states of chromium. Chromium samples--conditioned at various pH's and concentration to understand the effects--were then irradiated using a Coblat-60 gamma irradiator. Three optical spectroscopy analytical methods were used , including direct oxidation state measurements and complexation by either EDTA or DPC. Complexation by EDTA was found to not be a reliable method. Radiolytic oxidation of Cr(III) to Cr(VI), and reduction of Cr(VI) to Cr(III) were clearly seen, except for Cr(III) samples were a pH less than or equal to 2, where no change occurred.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

A COMPRESSED SENSING METHOD WITH ANALYTICAL RESULTS FOR LIDAR FEATURE CLASSIFICATION

We present an innovative way to autonomously classify LiDAR points into bare earth, building, vegetation, and other categories. One desirable product of LiDAR data is the automatic classification of the points in the scene. Our algorithm automatically classifies scene points using Compressed Sensing Methods via Orthogonal Matching Pursuit algorithms utilizing a generalized K-Means clustering algorithm to extract buildings and foliage from a Digital Surface Models (DSM). This technology reduces manual editing while being cost effective for large scale automated global scene modeling. Quantitative analyses are provided using Receiver Operating Characteristics (ROC) curves to show Probability of Detection and False Alarm of buildings vs. vegetation classification. Histograms are shown with sample size metrics. Our inpainting algorithms then fill the voids where buildings and vegetation were removed, utilizing Computational Fluid Dynamics (CFD) techniques and Partial Differential Equations (PDE) to create an accurate Digital Terrain Model (DTM) [6]. Inpainting preserves building height contour consistency and edge sharpness of identified inpainted regions. Qualitative results illustrate other benefits such as Terrain Inpainting s unique ability to minimize or eliminate undesirable terrain data artifacts. Keywords: Compressed Sensing, Sparsity, Data Dictionary, LiDAR, ROC, K-Means, Clustering, K-SVD, Orthogonal Matching Pursuit

99 GENERAL AND MISCELLANEOUS↗

Developing Methodology to Determine Pu Isotopic Composition by Laser Ablation MC-ICP-MS

This project will develop methodology to analyze the Pu isotope ratio in mixed U-Pu particles by laser ablation MC-ICP-MS. This will involve: 1) testing and validation of the Pu analytical method using mixed U-Pu solutions and Pu doped glasses, 2) isotopic analysis of mixed U-Pu particles by laser ablation MC-ICP-MS, and 3) continued development of the R-based data reduction program. Details regarding the analytical method development and results of QC testing will be output as a deliverable to the IAEA, along with an updated version of the LARA data reduction software.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogen monitoring requirements in the global technical regulation on hydrogen and fuel cell vehicles

Here, the United Nations Economic Commission for Europe Global Technical Regulation (GTR) Number 13 ( Global Technical Regulation on Hydrogen and Fuel Cell Vehicles ) is the defining document regulating safety requirements in hydrogen vehicles, and in particular, fuel cell electric vehicles (FCEVs). GTR Number 13 has been formally adopted and will serve as the basis for the national regulatory standards for FCEV safety in North America (led by the United States), Japan, Korea, and the European Union. The GTR defines safety requirements for these vehicles, including specifications on the allowable hydrogen levels in vehicle enclosures during in-use and post-crash conditions and on the allowable hydrogen emissions levels in vehicle exhaust during certain modes of normal operation. However, in order to be incorporated into national regulations, that is, to be legally binding, methods to verify compliance with the specific requirements must exist. In a collaborative program, the Sensor Laboratories at the National Renewable Energy Laboratory in the United States and the Joint Research Centre, Institute for Energy and Transport in the Netherlands have been evaluating and developing analytical methods that can be used to verify compliance with the hydrogen release requirements as specified in the GTR.

30 DIRECT ENERGY CONVERSION↗

Wake potentials and impedances of charged beams in gradually tapering structures

We develop an analytical method for calculating the geometric wakefield and impedances of an ultrarelativistic beam propagating on- and off-axis through an axially symmetric geometry with slowly varying circular cross-section, such as a transition. Unlike previous analytical methods, our approach permits detailed perturbative investigation of geometric wakefields, and detailed perturbative investigation of impedance as a function of frequency. We compare the accuracy of the results of our approach with numerical simulations performed using the code ECHO and determine parameters in which there is good agreement with our asymptotic analysis.

43 PARTICLE ACCELERATORS↗

An initial investigation into methods of computing transonic aerodynamic sensitivity coefficients

The primary accomplishments of the project are as follows: (1) Using the transonic small perturbation equation as a flowfield model, the project demonstrated that the quasi-analytical method could be used to obtain aerodynamic sensitivity coefficients for airfoils at subsonic, transonic, and supersonic conditions for design variables such as Mach number, airfoil thickness, maximum camber, angle of attack, and location of maximum camber. It was established that the quasi-analytical approach was an accurate method for obtaining aerodynamic sensitivity derivatives for airfoils at transonic conditions and usually more efficient than the finite difference approach. (2) The usage of symbolic manipulation software to determine the appropriate expressions and computer coding associated with the quasi-analytical method for sensitivity derivatives was investigated. Using the three dimensional fully conservative full potential flowfield model, it was determined that symbolic manipulation along with a chain rule approach was extremely useful in developing a combined flowfield and quasi-analytical sensitivity derivative code capable of considering a large number of realistic design variables. (3) Using the three dimensional fully conservative full potential flowfield model, the quasi-analytical method was applied to swept wings (i.e. three dimensional) at transonic flow conditions. (4) The incremental iterative technique has been applied to the three dimensional transonic nonlinear small perturbation flowfield formulation, an equivalent plate deflection model, and the associated aerodynamic and structural discipline sensitivity equations; and coupled aeroelastic results for an aspect ratio three wing in transonic flow have been obtained.

Carlson, Leland A.↗

The spectrum of an SU(3) gauge theory with a fundamental Higgs field

In gauge theories, the physical, experimentally observable spectrum consists only of gauge-invariant states. This spectrum can be different from the elementary spectrum even at weak coupling and in the presence of the Brout–Englert–Higgs effect. We demonstrate this for an SU(3) gauge theory with a single fundamental Higgs, a toy theory for grand-unified theories. The manifestly gauge-invariant approach of lattice gauge theory is used to determine the spectrum in four different channels. It is found to be qualitatively different from the elementary one, and especially from the one predicted by standard perturbation theory. The result can be understood in terms of the Fröhlich–Morchio–Strocchi mechanism. In fact, we find that analytic methods based on this mechanism, a gauge-invariant extension of perturbation theory, correctly determine the spectrum, and give already at leading order a reasonably good quantitative description. Together with previous results this supports that this approach is the analytic method of choice for theories with a Brout–Englert–Higgs effect.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Research and applications in aeroservoelasticity at the NASA Langley Research Center

A review of analytical methods used to analyze flexible vehicles with active controls is presented. Methods used to approximate and correct unsteady aerodynamic forces used in the analysis are discussed. Recent advances in the application of optimal methods to digital control law synthesis are presented. The use of active controls in an integrated design process is also discussed. Finally, the results of recent wind-tunnel studies aimed at demonstrating active control concepts and validating the analytical methods are presented.

Abel, Irving↗

Evaluation of electronic state of Cs-adsorbed clay minerals by NEXAFS analysis using DFT calculations

In this work, a combined analytical method of NEXAFS measurement and DFT-calculation was employed for the evaluation of Cs states in clay minerals. The measured Cs M 4,5 NEXAFS spectra of Cs halides were analyzed using the DFT-calculations in order to establish the analytical methods. The NEXAFS spectra of the Cs halides were well reproduced by incorporating the core-hole strength. The Cs M 4,5 NEXAFS spectrum of the clay minerals was well reproduced by the DFT-calculations including the major transitions and tail structures with the established method. Further evaluation of this spectrum by charge density analysis suggested that these major transitions and the tail structures likely reflect the bonding state and the local environment around the Cs atoms. Comparison of electronic states of Cs in the clay mineral with those in the Cs halides by DFT-calculations has shown that the interaction between Cs and the nearest-neighbor atom is largest in the clay mineral, which differs from those of Cs halides. This happened due to the energy level of Cs-5s and 5p, which was closer to that of O-2s and 2p than the s and p orbitals of other alkali metal and alkali earth metal elements.

36 MATERIALS SCIENCE↗

Description of Sensor Assignment Optimization Method as Deployed on a Multi-Node Cluster

Data analytic methods are being developed to address the problem of how to assign a sensor set in a nuclear facility such that a requisite level of process monitoring capability is realized and that the sensor set is sufficiently rich to determine the status of the individual sensors with respect to need for calibration. There is an awareness in the nuclear industry that data analytics combined with rich sensor sets represent a means to improve operations and reduce costs. In the industry the calibration problem has been previously approached as an empirical data-driven problem with several methods having been developed. However, the experience of the utilities over the past ten years with these methods indicates that the absence of physics-based information renders the data-driven approach less reliable. Complicating factors such as the inherent variability of operation (both equipment alignment and operating condition) can confound a pure data-driven approach while there are no rigorous guidelines for determining what constitutes an adequate sensor set. The solution under development to overcome these shortcomings supplements the data analytic method with process information in a so-called process-constrained data-analytic approach. Simple balance equations are written for generic components (e.g., mechanical pump, valve, and heat exchanger). These do not require a priori knowledge of process parameters, such as heat transfer coefficients or friction factors. All that is needed on the part of the utility user is to identify the components and how they are connected. This report describes the development of a parallel computing capability for determining the optimal sensor set. The optimal sensor set problem suffers from the curse of dimensionality. Computation time increases exponentially as the size of the system grows. To overcome this difficulty a pre-conditioner algorithm is developed to find an approximate solution close the actual solution. This serves as a seed for the full-blown algorithm and acts to constrain the space that must searched. The optimization algorithms are described and the implementation on a parallel computing platform is described. The application of the method to a use case we are solving in collaboration with our utility partner served to illustrate how the default sensor set in a nuclear plant may not provide sufficient coverage to infer sensor calibration status.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Computer modeling of a two-junction, monolithic cascade solar cell

The theory and design criteria for monolithic, two-junction cascade solar cells are described. The departure from the conventional solar cell analytical method and the reasons for using the integral form of the continuity equations are briefly discussed. The results of design optimization are presented. The energy conversion efficiency that is predicted for the optimized structure is greater than 30% at 300 K, AMO and one sun. The analytical method predicts device performance characteristics as a function of temperature. The range is restricted to 300 to 600 K. While the analysis is capable of determining most of the physical processes occurring in each of the individual layers, only the more significant device performance characteristics are presented.

Lamorte, M. F.↗

The Second Skin: A Wearable Sensor Suite that Enables Real-Time Human Biomechanics Tracking Through Deep Learning

Objective: Real-time determination of human kinematics and kinetics could advance biomechanics research and enable valuable applications of biofeedback and generalizable exoskeleton control. Here, this work aims to investigate a taskindependent, user-independent method for obtaining precise realtime joint state estimation across lower-body joints during a wide variety of tasks. Methods: We developed a generalizable sensing approach using a suit comprised of inertial measurement units (IMUs) and pressure insoles. With the suit, we collected a dataset of 33 tasks commonly performed during construction and hazardous waste cleanup (N = 10). We then trained deep learning user-independent, task-agnostic models to estimate joint lowerbody kinematics and dynamics using only worn sensor data. We likewise computed joint kinematics and dynamics analytically from sensor data to serve as a comparison tool for model results. Results: Our models achieved overall angle estimation root-meansquared-errors (RMSE) of 6.56±.92°, 8.60±1.01°, 7.58±.89°, and 6.00±.73° compared to 13.9±.1.3°, 15.31±1.0°, 10.76±.70°, and 7.56±.48° via analytical methods at the lower back, hip, knee, and ankle, respectively. Likewise, our models achieved overall normalized moment estimation RMSEs of .207±.069 Nm/kg, .242±.044 Nm/kg, .202±.038 Nm/kg, and .193±.034 Nm/kg compared to .306±.036 Nm/kg, .407±.021 Nm/kg, 1.18 ±.022 Nm/kg, and 1.73±.071 Nm/kg via analytical methods at the lower back, hip, knee, and ankle, respectively. Conclusion: These results are comparable to other state-of-the-art wearable sensing systems, establishing deep learning as a viable sensing approach that generalizes to new users and tasks. Significance: This work shows promise for enabling accurate real-world biomechanical data collection and enhancement of biofeedback systems and wearable robot control.

Casey, Ryan T. F. [Georgia Institute of Technology↗

Forensic investigation of plutonium metal: a case study of CRM 126

In our study, a certified plutonium metal reference material (CRM 126) with a known production history is examined using analytical methods that are commonly employed in nuclear forensics for provenancing and attribution. Moreover, the measured plutonium isotopic composition and actinide assay are consistent with values reported on the reference material certificate. Model ages from U/Pu and Am/Pu chronometers agree with the documented production timeline. Finally, these results confirm the utility of these analytical methods and highlight the importance of a holistic approach for forensic study of unknown materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Review of Online Monitoring within Used Nuclear Fuel Recycling Processes

The processing of used nuclear fuels and related materials is often complex and variable. The ability to quickly optimize conditions to the material being processed can aid in increasing efficiency and safety, but requires very quick determination of the conditions present in the feedstock, the process, and the product. Furthermore, accurate quantification of materials such as enriched uranium and plutonium aids in maintaining material accountancy and avoiding nuclear proliferation risks. Traditional analytical methods require process samples to be collected and analyzed in a laboratory, which often takes days to weeks. Online monitoring is suitable for collecting this information nearly instantaneously, enabling much faster optimization of the process or detection of material diversion. Online monitoring is also beneficial as it is typically based on robust and nondestructive analytical methods, so no material is removed as samples. This review examines online monitoring relevant to used nuclear fuel processing for the determination of both chemical and physical parameters. The chemical parameters include quantities such as concentration, isotopic composition, and speciation. These values are often well suited to spectroscopic or spectrometric measurements as they are fast, nondestructive, and easily implemented in an online manner. Physical quantities are often more varied and include temperature, pressure, tank fill levels, and others. Due to the specificity of these quantities, specialized instrumentation is often used. However, this instrumentation is often amendable to online monitoring.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A new framework for X-ray photon correlation spectroscopy analysis from polycrystalline materials

Here, we report a new analytical framework for interpreting data from X-ray photon correlation spectroscopy (XPCS) measurements on polycrystalline materials characterized by strong scattering intensity variations at fixed wavevector magnitude (i.e., anisotropic scattering). Currently, no analytical method exists for the interpretation of the time-dependent anisotropic scattering from such materials. The framework is applied to interrogate the dynamics of a spherical micelle-forming diblock copolymer melt below the order-disorder transition, wherein finite size grains of micellar body-centered cubic structure produce anisotropic scattering. A wealth of analytical information is recovered from a simple measurement, including distributions of relaxation times and speeds associated with micelles within grains. The findings of this study demonstrate the efficacy of this new analytical method, which may be readily adapted for application to a variety of materials and systems.

47 OTHER INSTRUMENTATION↗

An Overview of the United States Department of Energy's Nuclear Criticality Safety Program and Future Challenges

The United States (US) Department of Energy (DOE)/National Nuclear Security Administration (NNSA) Nuclear Criticality Safety Program (NCSP) was formally established in January 1998 as part of the Defense Nuclear Facility Safety Board (DNFSB) Recommendation 97-2 implementation plan. The NCSP was initially focused on seven NCSP tasks: Critical Experiments, Benchmarking, Analytical Methods, Nuclear Data, Training and Qualification, Information Preservation and Dissemination, and Applicable Ranges of Bounding Curves and Data. The first NCSP 5-year plan was published in August 1999. Now, more than 20 years later, NCSP continues to serve the United States and the nuclear criticality safety (NCS) community around five technical program elements (TPEs): Analytical Methods, Information Preservation and Dissemination, Integral Experiments, Nuclear Data, and Training and Education. NCSP has three chartered support groups, the Criticality Safety Support Group, the Nuclear Data Advisory Group, and the DOE Criticality Safety Coordinating Team, all of which provide technical advisement to the NCS community, to DOE, and to the NCSP manager. NCSP has a comprehensive mission and vision document that provides technical and budget priorities for TPE attributes and goals to ensure that the needs of the NCS community and DOE NCS are prioritized appropriately to meet the goals defined by the 1998 DNFSB recommendation. Like any DOE/NNSA program, NCSP faces significant challenges in the future that involves program funding, rising nuclear facility costs, aging critical assembly infrastructure, knowledge retention, and other issues. This paper discusses NCSP and provides some insights into these and other challenges moving into the future.

Bowen, Douglas G.↗