Search NASA⌕ Search

SEARCH · Search NASA

Results for “angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Preliminary results from a subsonic high-angle-of-attack flush airdata sensing (HI-FADS) system - Design, calibration, algorithm development, and flight test evaluation

A nonintrusive high angle-of-attack flush airdata sensing (HI-FADS) system was installed and flight-tested on the F-18 high alpha research vehicle. This paper discusses the airdata algorithm development and composite results expressed as airdata parameter estimates and describes the HI-FADS system hardware, calibration techniques, and algorithm development. An independent empirical verification was performed over a large portion of the subsonic flight envelope. Test points were obtained for Mach numbers from 0.15 to 0.94 and angles of attack from -8.0 to 55.0 deg. Angles of sideslip ranged from -15.0 to 15.0 deg, and test altitudes ranged from 18,000 to 40,000 ft. The HI-FADS system gave excellent results over the entire subsonic Mach number range up to 55 deg angle of attack. The internal pneumatic frequency response of the system is accurate to beyond 10 Hz.

Whitmore, Stephen A.↗
NASA NTRS1990

A preliminary look at techniques used to obtain airdata from flight at high angles of attack

Flight research at high angles of attack has posed new problems for airdata measurements. New sensors and techniques for measuring the standard airdata quantities of static pressure, dynamic pressure, angle of attack, and angle of sideslip were subsequently developed. The ongoing airdata research supporting NASA's F-18 high alpha research program is updated. Included are the techniques used and the preliminary results. The F-18 aircraft was flown with three research airdata systems: a standard airdata probe on the right wingtip, a self-aligning airdata probe on the left wingtip, and a flush airdata system on the nose cone. The primary research goal was to obtain steady-state calibrations for each airdata system up to an angle of attack of 50 deg. This goal was accomplished and preliminary accuracies of the three airdata systems were assessed and are presented. An effort to improve the fidelity of the airdata measurements during dynamic maneuvering is also discussed. This involved enhancement of the aerodynamic data with data obtained from linear accelerometers, rate gyros, and attitude gyros. Preliminary results of this technique are presented.

Moes, Timothy R.↗
NASA NTRS1990

Development of pitch angle anisotropy and velocity diffusion of pickup ion shell distribution by solar wind turbulence

The evolution of pitch angle anisotropy in initially isotropic spherical shell distribution of pickup ions subjected to a continuous influence of weak or moderate intrinsic solar wind turbulence is investigated using a physical model which assumes that the wave of the solar wind turbulence is propagating mainly in the direction parallel to the ambient magnetic field. It is shown that, because of the pitch angle dependence of the velocity diffusion process, a significant pitch angle anisotropy of pickup ion shell distribution develops in the early stage of the diffusion process. Although it is smeared out later on, the result can be of significant importance, especially if the pickup ion density is large, because the pitch angle anisotropy can excite collective instabilities and increase the wave level, thus accelerating the diffusion process.

Yoon, Peter H.↗
NASA NTRS1991

A system for testing airdata probes at high angles of attack using a ground vehicle

A system to calibrate airdata probes at angles of attack between 0 and 90 deg was developed and tested at the NASA Ames Dryden Flight Research Facility. This system used a test fixture mounted to the roof of a ground vehicle and included an onboard instrumentation and data acquisition system for measuring pressures and flow angles. The data could be easily transferred to the facility mainframe computer for further analysis. The system was designed to provide convenient and inexpensive airdata probe calibrations for projects which require airdata at high angles of attack, such as the F-18 High Alpha Research Program. This type of probe was tested to 90 deg angle of attack in a wind tunnel and using the ground vehicle system. The results of both tests are in close agreement. An airdata probe with a swiveling pilot-static tube was also calibrated with the ground vehicle system. This paper presents the results of these tests and gives a detailed description of the test system.

Geenen, Robert J.↗
NASA NTRS1991

Effects of sweep angle and passive relaminarization devices on a supersonic swept-cylinder boundary layer

The effects of passive leading-edge devices on the boundary layer of a swept cylinder in supersonic flow with very low free-stream disturbance levels are investigated. Tests are conducted at Mach 3.5 over a free-stream Reynolds number based on model diameter of 15,000 to 150,000, and sweep angles of 60 deg and 76 deg are used to evaluate possible sweep-angle effects. The devices tested include a sawtoothed leading edge, square device, and a fence. It is observed that at a sweep angle of 76 deg, relaminarization of the supersonic attachment-line flow is achieved by several of the devices, while no devices are successful at a sweep angle of 60 deg.

Creel, T. R.↗
NASA NTRS1991

A two camera video imaging system with application to parafoil angle of attack measurements

This paper describes the development of a two-camera, video imaging system for the determination of three-dimensional spatial coordinates from stereo images. This system successfully measured angle of attack at several span-wise locations for large-scale parafoils tested in the NASA Ames 80- by 120-Foot Wind Tunnel. Measurement uncertainty for angle of attack was less than 0.6 deg. The stereo ranging system was the primary source for angle of attack measurements since inclinometers sewn into the fabric ribs of the parafoils had unknown angle offsets acquired during installation. This paper includes discussions of the basic theory and operation of the stereo ranging system, system measurement uncertainty, experimental set-up, calibration results, and test results. Planned improvements and enhancements to the system are also discussed.

Meyn, Larry A.↗
NASA NTRS1991

High-speed pitch angle sorter

A high-speed method was developed to compress the two-dimensional angular distribution of space particles gathered by space plasma instrumentation into the angle distribution, where the pitch angle is polar angle with respect to the ambient magnetic field. The pitch angle sorter can handle rates of up to 2 MHz and it is designed to accommodate high angular resolution plasma analyzers that are placed on a rotating spacecraft. This compression is achieved by relying on digitally encoded lookup tables to eliminate all arithmetic operations while applying the high symmetry of this compression to reduce the amount of digital memory.

Keller, John W.↗
NASA NTRS1991

Pitch-angle scattering of cometary ions - Computer simulations

The relationships between the rate of pitch-angle scattering induced by wave-particle interactions and two parameters, alpha, and the cometary ion interjection rate, Lambda-j, are studied with the aid of one-dimensional electromagnetic hybrid computer simulations of homogeneous plasmas. The simulations are done with relatively weak ion injection rates commensurate with those in the distant environment of the Comet Halley. In response to the linear temporal growth of the fluctuating magnetic field energy, the injected ions pitch-angle scatter toward isotropy in both the quasi-parallel and quasi-perpendicular regimes. For the injection of cometary oxygen ions, the simulations show pitch-angle scattering rates that increase as the square root of the injection rate. The oxygen ion pitch-angle scattering rates are roughly twice as large at perpendicular injection, again in qualitative agreement with observations.

Gary, S. P.↗
NASA NTRS1991

An experimental study of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack

An experimental study of the effects of aft blowing on the forebody vortex asymmetry over a 3.0 caliber tangent ogive body at high angles of attack was conducted. The tip of the ogive body was equipped with a single blowing nozzle whose position could be adjusted. The tests were conducted in a subsonic wind tunnel at laminar flow conditions. The effects of model roll, angle of attack, blowing coefficient, and blowing nozzle axial position were independently studied. Surface pressure measurements and flow visualization results were obtained. Aft blowing was observed to alleviate the degree of vortex asymmetry at all angles of attack. The blowing was found to be more effective at the higher angles of attack. However, proportional control of the degree of vortex asymmetry was not observed, because the initial flowfield was highly asymmetric.

Gittner, Nathan M.↗
NASA NTRS1992

Characterization of Martian near-subsurface materials by determination of cohesion and angle of internal friction

Back-analysis (reconstruction) of the stability of thirty avalanche chutes was performed in the very limited areas where high resolution imaging overlapped with available 1:500 K topographic map coverage. A new technique was developed to incorporate the third dimension (width) of an avalanche chute in stability back-analysis in order to yield unambiguous values of cohesion and angle of internal friction. The procedure is based upon extending the ordinary method of slices to three dimensions, in order to construct avalanche chute cross-sections whose widths and depths vary as a function of gradient, gravity, density of material, and phi and c. Applying the technique to the well documented slide at Lodalen, Norway as a test produces excellent correspondence with reality. Generally, the technique reveals that the width:depth ratio of any avalanche chute decreases with increasing contrast between the average slope angle and the angle of internal friction. Applying this technique to the martian avalanche chute yields results consistent with indications from earlier work, but with greater certainty. Values of cohesion and angle of internal friction identify the materials at the time of failure as moderately cohesive debris. If Sharp's identification of these features as avalanche chutes is correct, then the results here imply that weathering processes have had a significant effect to depths of tens of meters (where failure has occured) below the martian surface. It is also implied that on relatively steep slopes within Valles Marineris, sizable, unaltered, unmantled bedrock exposures for high resolution spectral and spatial scanning by Mars Observer may be scarce.

Sullivan, R. J.↗
NASA NTRS1992

In-flight leading-edge extension vortex flow-field survey measurements on a F-18 aircraft at high angle of attack

Flow-field measurements on the leading-edge extension (LEX) of the F-18 High Alpha Research Vehicle (HARV) were obtained using a rotating rake with 16 hemispherical-tipped five-hole probes. Detailed pressure, velocity, and flow direction data were obtained through the LEX vortex core. Data were gathered during 1-g quasi-stabilized flight conditions at angles of attack alpha from 10 degrees to 52 degrees and at Reynolds numbers based on mean aerodynamic cord up to 16 x 10(exp 6). Normalized dynamic pressures and crossflow velocities clearly showed the primary vortex above the LEX and formation of a secondary vortex at higher angles of attack. The vortex was characterized by a ring of high dynamic pressure surrounding a region of low dynamic pressure at the vortex core center. The vortex core, subcore diameter, and vertical location of the core above the LEX increased with angle of attack. Minimum values for static pressure were obtained in the vortex subcore and decreased nearly linearly with increasing angle of attack until vortex breakdown. Rake-measured static pressures were consistent with previously documented surface pressures and showed good agreement with flow visualization flight test results. Comparison of the LEX vortex flight test data to computational solutions at alpha approximately equals 19 degrees and 30 degrees showed fair correlation.

David M Richwine↗
NASA NTRS1992

Effects of nose bluntness and angle of attack on slender bodies in hypersonic flows

The effects of angle of attack and nose bluntness on the flow field and wall quantities are investigated for hypersonic flows of air over slender bodies. The bodies considered are slender cones and straight biconic configurations. The numerical procedures used are based on the solution of complete Navier-Stokes equations in the nose region and parabolized Navier-Stokes equations in the downstream region. Results are obtained for a wide range of free stream conditions in which the gas behind the shock is treated as perfect. The flow field variables and surface quantities show significant differences when the angle of attack and nose bluntness are varied. The postshock flow field is studied in detail from the contour plots of Mach number, density, and temperature. Flow separation is observed on the leeward plane for an on-axis, 12.84 deg/7 deg (fore-cone and aft-cone angles) biconic geometry at 12 deg angle of attack. Also, the windward and leeward heating rates for the fore-cone section decrease by a factor of four and five, respectively, when the nose bluntness is increased by an order of magnitude. The effect of nose bluntness for slender cone persists as far as 200 nose radii downstream.

Tiwari, S. N.↗
NASA NTRS1992

Variation in multiring basic structures as a function of impact angle

Previous studies have demonstrated that the impact process in the laboratory varies as a function of impact angle. This variation is attributed to changes in energy partitioning and projectile failure during the impact and, in simple craters, produces a sequence of progressively smaller and more asymmetric crater forms as impact angle decreases from approximately 20 degrees. Variations in impact angle can produce differences in the appearance of multiring impact basins. Comparisons of Orientale to the more oblique impact structure at Crisium also suggests that these differences primarily reflect the degree of cavity collapse. The relative changes in massif ring topography, basin scarp relief, and the distribution of peripheral mare units are consistent with a reduction in degree of cavity collapse with decreasing impact angle. The prominent uprange basin scarps and the restriction of tectonically derived peripheral mare units along uprange ring structures also may indicate an uprange enhancement of failure during cavity collapse. Finally, although basin ring faults appear to be preferred pathways for mare volcanism, fault-controlled peripheral mare volcanism occurs most readily uprange of an oblique impact; elsewhere such volcanism apparently requires superposition of an impact structure on the ring fault.

Wichman, R. W.↗
NASA NTRS1992

Effect of impact angle on central-peak/peak-ring formation and crater collapse on Venus

Although asymmetry in ejecta patterns and craters shape-in-plan are commonly cited as diagnostic features of impact angle, the early-time transfer of energy from impactor to target also creates distinctive asymmetries in crater profile with the greatest depth uprange. In order to simulate gravity-controlled crater-growth, laboratory experiments use loose particulate targets as analogs for low-strength material properties following passage of the shock. As a result, impact crater diameter D in laboratory experiments generally is many times greater than the impactor diameter 2r (factor of 40), and early-time asymmetries in energy transfer from oblique impacts are consumed by subsequent symmetrical crater growth, except at the lowest angles (less than 25 deg). Such asymmetry is evident for oblique (less than 60 deg from horizontal) impacts into aluminum where D/2r is only 2 to 4. Because cratering efficiency decreases with increasing crater size and decreasing impact angle, large scale planetary craters (4080 km) should have transient excavation diameters only 6-10 times larger than the impactor. At basin scales, D/2r is predicted to be only 3-5, i.e., approaching values for impacts into aluminum in laboratory experiments. As a result, evidence for early-time asymmetry in impactor energy transfer should become evident on planetary surfaces, yet craters generally retain a circular outline for all but the lowest impact angles.

Schultz, Peter H.↗
NASA NTRS1993

System for determining the angle of impact of an object on a structure

A method for determining the angle of impact of an object on a thin-walled structure which determines the angle of impact through analysis of the acoustic waves which result when an object impacts a structure is presented. Transducers are placed on and in the surface of the structure which sense the wave caused in the structure by impact. The waves are recorded and saved for analysis. For source motion normal to the surface, the antisymmetric mode has a large amplitude while that of the symmetric mode is very small. As the source angle increases with respect to the surface normal, the symmetric mode amplitude increases while the antisymmetric mode amplitude decreases. Thus, the angle of impact is determined by measuring the relative amplitudes of these two lowest order modes.

Prosser, William H.↗
NASA NTRS1932

Heat Dissipation from a Finned Cylinder at Different Fin-Plane/Air-stream Angles

This report gives the results of an experimental determination of the temperature distribution in and the heat dissipation from a cylindrical finned surface for various fin-plane/air-stream angles. A steel cylinder 4.5 inches in diameter having slightly tapered fins of 0.30-inch pitch and 0.6 -inch width was equipped with an electrical heating unit furnishing 13 to 248 B.T.U. per hour per square inch of inside wall area. Air at speeds form 30 to 150 miles per hour was directed at seven different angles from 0 degrees to 90 degrees with respect to the fin planes. The tests show the best angle for cooling at all air speeds to be about 45 degrees. With the same temperature for the two conditions and with an air speed of 76 miles per hour, the heat input to the cylinder can be increased 50 percent at 45 degrees fin-plane/air-stream angle over that at 0 degrees.

Schey, Oscar W↗
NASA NTRS1939

Hydrodynamic and Aerodynamic Tests of a Family of Models of Seaplane Floats with Varying Angles of Dead Rise - N.A.C.A. Models 57-A, 57-B, and 57-C

Three models of V-bottom floats for twin-float seaplanes (N.A.C.A. models 57-A, 57-B, and 57-C) having angles of dead rise of 20 degrees, 25 degrees, and thirty degrees, respectively, were tested in the N.A.C.A. tank and in the N.A.C.A. 7- by 10-foot wind tunnel. Within the range investigated, the effect of angle of dead rise on water resistance was found to be negligible at speeds up to and including the hump speed, and water resistance was found to increase with angle of dead rise at planing speeds. The height of the spray at the hump speed decreased with increase in angle of dead rise and the aerodynamic drag increased with dead rise. Lengthening the forebody of model 57-B decreased the water resistance and the spray at speeds below the hump speed. Spray strips provided an effective means for the control of spray with the straight V sections used in the series but considerably increased the aerodynamic drag. Charts for the determination of the water resistance and the static properties of the model with 25 degrees dead rise and for the aerodynamic drag of all the models are included for use in design.

Parkinson, John B↗
NASA NTRS1945

Effect of Propeller-Axis Angle of Attack on Thrust Distribution over the Propeller Disk in Relation to Wake-Survey Measurement of Thrust

Tests were made to investigate the variation of thrust distribution over the propeller disk with angle of pitch of the propeller thrust axis and to determine the disposition and the minimum number of rakes necessary to measure the propeller thrust. The tests were made at a low Mach number for a low and a high blade angle with the propeller operating at three small angles of pitch, and some of the tests were repeated at a higher Mach number. The data obtained show that, for small angles of pitch, large changes occur in the energy distribution in the wake which prohibit the use of a single survey rake for thrust measurement in flight tests and limit the use of a single rake in wind-tunnel tests. Under certain conditions, the energy distribution in the wake took on a symmetrical form and two diametrically opposed survey rakes were shown to be satisfactory for obtaining propeller thrust. (author)

Pendley, Robert E↗