SEARCH · Search NASA

Results for “area optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1995

1025:1 Area Ratio Nozzle Evaluated at High Combustion Chamber Pressure

A recently completed experimental test program obtained performance data on an optimally contoured nozzle with an exit-to-throat area ratio of 1025:1 and on a truncated version of this nozzle with an area ratio of 440:1. The nozzles were tested with gaseous hydrogen and liquid oxygen propellants at combustion chamber pressures of 12.4 to 16.5 mPa (1800 to 2400 psia). Testing was conducted in the altitude test capsule at the NASA Lewis Research Center's Rocket Engine Test Facility (RETF), and results were compared with analytical performance predictions. This testing builds on previous work with this nozzle at Lewis, where testing was completed at nominal chamber pressure of 350 psia. High-area-ratio nozzles have long been sought as a means to increase the performance of spacebased rocket engines. However, as the area ratio increases, the physical size and weight of the nozzle also increase. As a result, engine and vehicle designers must make tradeoffs between nozzle size and performance enhancement. Until this test program, very little experimental data existed on the performance of the high-area-ratio nozzles used in rocket engine designs. The computer codes being used by rocket engine designers rely on data extrapolated from tests of low-area-ratio nozzles, and these extrapolations do not always provide the accuracy needed for a reliable design assessment. Therefore, we conducted this high-area-ratio nozzle testing program to provide performance data for use in rocket engine design and analysis computer codes. The nozzle had a nominal 2.54-cm- (1-in.-) diameter throat, an exit diameter of 81.3-cm (32.0-in.) at an exit-to-throat area ratio of 1025, and a length of 128.6 cm (50.6 in.). Testing was conducted in an altitude test capsule to simulate the static pressure at altitude by vacuum pumping. Data such as propellant mass flow, oxidizer-to-fuel mixture, and thrust were measured. These measurements were then used to calculate performance factors such as the thrust coefficient, the characteristic exhaust velocity efficiency, and the vacuum specific impulse. In addition, the nozzle temperature was measured to calculate the amount of heat transferred from the combustion gases to the nozzle.

Source record↗

DOE OSTI2024

Solar, Wind, and Load Forecasting Dataset for MISO, NYISO, and SPP Balancing Areas

The Performance-based Energy Resource Feedback, Optimization, and Risk Management (PERFORM) program is an initiative intended to foster "a fundamental shift in grid management rooted in an understanding of asset risk and system risk" (ARPA-E 2020). Launched by the Advanced Research Projects Agency-Energy (ARPA-E), the program supports efforts to incorporate uncertainty in electric power decision making. In support of PERFORM, the National Renewable Energy Laboratory (NREL) has produced a set of time-coincident forecasts of solar, wind, and load profiles. As part of Phase I of the PERFORM effort, NREL created a dataset that consists of one year of time-coincident load, wind, and solar actuals and probabilistic forecasts based on data from the Electric Reliability Council of Texas (ERCOT) (Bryce et al. 2023). In Phase II, NREL developed similar datasets for three other U.S. Independent System Operators (ISO): the Midcontinent Independent System Operator (MISO), the New York Independent System Operator (NYISO), and the Southwest Power Pool (SPP).

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2024

A Workflow to Optimize Fast Neutron Irradiation in A Thermal Neutron Spectrum Test Reactor Leveraging Open-Source Tools

The Advanced Test Reactor (ATR) located at Idaho National Laboratory (INL) is one of the key nuclear engineering research and testing facilities within the US Department of Energy (DOE). The ATR is one of few high-power research reactors in the world with different application including accelerated testing of nuclear fuel, materials irradiation in a very high neutron flux environment, and medical radioisotope production [1]. Also, the ATR offers opportunities for testing fast spectrum fission and fusion reactor materials. The key challenges in this area are in further detailing and optimizing a fast spectrum environment within a thermal test reactor. This challenge involves researching, developing, and testing novel concepts for the multiplying of neutron populations into ever higher energy spectra in high flux test reactors like ATR. The main objective of this work is to investigate candidate materials for establishing a fast neutron experiment irradiation in thermal neutron spectrum test reactors which can be accomplished by filtering thermal and epithermal neutrons and boosting fast neutrons at designated irradiation positions. However, adding these filters will render the neutron spectrum and the criticality of the system. The selection of the thickness and material layers should be accomplished by developing an optimization design algorithm that is applicable for ATR to enhance the fast neutron spectrum irradiation utilizing high-fidelity Monte Carlo methods along with advanced machine learning capabilities. This paper presents workflow for design optimization to enhance fast neutron irradiation in the ATR. The workflow leverages open-source tools to develop an algorithm that is viable to ATR and can be leveraged in other reactors. The following sections discuss the development of the experiment design optimization workflow and its application to ATR irradiation positions.

42 - ENGINEERING↗

DOE OSTI2026

Bayesian Optimization of Non-Invariant Systems with Constraints Developed for Application to the ECR Ion Source VENUS

In this work, we consider the optimization of non-invariant systems with both safety and control constraints. We present a new approach based on Bayesian optimization for the dynamic, safe and controlled optimization of such systems. Although there are other possible use cases, we focus on the application to the electron cyclotron resonance ion source VENUS. From experimental data, we have observed that VENUS behaves to first order as a non-invariant dynamic system with moving areas of instability. Our novel approach aims at providing a tool that can maintain system optimization in a safe way. This is accomplished by making sure the objective function, the beam current in the case of VENUS, does not fall under an operational minimum, while simultaneously requiring the optimization to avoid areas where VENUS is unstable. We compare the result of our approach on synthetic data modeled to mimic the behavior of VENUS with two methods from the literature, a standard Bayesian optimizer and a safe Bayesian optimizer, both adapted to deal with dynamic systems. A cross Student T-test is conducted to show the significance of the improvement given by the new method we introduce here, regarding the two preexisting methods we compared to. The results of the tests conducted on synthetic data show that the proposed method succeeds at maintaining the system optimized and obeys the predefined constraints better than the literature methods explored.

Bayesian optimization↗

DOE OSTI2025

Optimal Design and Operation of Intensified Absorbers with 3D-Printed Packing for Solvent-Based CO 2 Capture

Many potential solvent-based carbon capture processes suffer from a high heat of absorption of CO 2 that adversely affects the thermodynamic driving force. While interstage coolers are often used for removing a portion of the generated heat by removing the solvent or a portion of the solvent from a stage and cooling and returning it back to the absorber, they can be placed only at discrete locations in the tower. This work investigates intensified absorbers with 3D-printed packing that includes an internal cooler and therefore can be potentially used for maximizing the operational efficiency of the absorbers for CO 2 capture. The intensified absorber is modeled by using a generic, first-principles, equation-oriented absorber column model. Since the placement of these intensified packings would cause a loss of area/volume used for mass transfer, optimization of the proposed intensified absorber is performed by optimally selecting the locations at which to place these devices and designing them such that the trade-off due to the addition of the heat removal area and the resulting loss in the mass transfer area is accounted for. Results show that optimally placed and designed intensified packings can lead to a significant increase in the capture efficiency of the process in comparison to a similar column with no internal cooling. It is also observed that by optimally placing and designing intensified packings, the lean solvent flow rate to the absorber can be decreased, and the CO 2 lean loading can be increased while still maintaining the same capture efficiency. These process changes can lead to a substantial reduction in the cost of capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1988

Review of power requirements for satellite remote sensing systems

The space environment offers a multitude of attributes and opportunities to be used to enhance human life styles and qualities of life for all future generations, worldwide. Among the prospects having immense social as well as economic benefits are earth-observing systems capable of providing near real-time data in such areas as food and fiber production, marine fisheries, ecosystem monitoring, disaster assessment, and global environmental exchanges. The era of Space Station, the Shuttle program, the planned unmanned satellites in both high and low Earth orbit will transfer to operational status what, until now, has been largely research and development proof of concept for remotely sensing Earth's natural and cultural resources. An important aspect of this operational status focuses on the orbital designs and power requirements needed to optimally sense any of these important areas.

Morain, Stanley A.↗

DOE OSTI2020

VALVE TIMING AND AREA PROFILE SELECTION FOR HYDRAULIC PUMPS AND MOTORS

A significant amount of research has been conducted to select valve timing and area profiles that create efficient and quiet hydraulic pumps and motors. Numerous active valve architectures have been modeled and optimized, but the rationale for the final solution is often unclear. The solution is usually highly dependent on the modeled valve geometry constraints and the duty cycle of the pump or motor for which the valve was optimized. This paper first presents an ideal valve area profile and what compromises are made to design for a working pressure and speed range. The ideal valve area profile is resolved using a piston-cylinder model with a pressure dependent bulk modulus and variable valve openings. The piston-cylinder is first modeled as a pump with passive (check) valves and a specified pressure drop across the valves to determine the ideal area profile. A generalization of the ideal timing is demonstrated for positive pressure differential and positive rotation direction, also known as the first quadrant. The effects on valve timing when varying pressure are shown for the first quadrant, but the trends can be extrapolated for all quadrants of operation. The ideal valve profile is implemented as fixed valve timing, meaning the valve area is only a function of the timing angle, in a pump-motor. The pump-motor is simulated in one rotation direction through a pressure range. Performance is high in pumping operation, but when the pressure differential is reversed, cylinder pressure spikes ensue. Two strategies to modify an ideal valve area profile are presented: timing grooves and a pressure shifted valve timing. Timing grooves reduce pressure spikes and cavitation in the cylinder but generally increase throttling losses. A pressure shifted valve timing has lower throttling energy losses, making it the favored solution.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2020

Machine learning for geophysical characterization of brittleness: Tuscaloosa Marine Shale case study

Brittleness is one of the most important reservoir properties for unconventional reservoir exploration and production. Better knowledge about the brittleness distribution can help to optimize the hydraulic fracturing operation and lower costs. However, there are very few reliable and effective physical models to predict the spatial distribution of brittleness. We have developed a machine learning-based method to predict subsurface brittleness by using multidiscipline data sets, such as seismic attributes, rock physics, and petrophysics information, which allows us to implement the prediction without using a physical model. The method is applied on a data set from Tuscaloosa Marine Shale, and the predicted rock physics template is close to the calculated value from conventional inverted elastic parameters. Therefore, the proposed method helps determine areas of the reservoir that have optimal geomechanical properties for successful hydraulic fracturing.

Geochemistry & Geophysics↗

DOE OSTI2020

Potential Energy, Demand, Emissions, and Cost Savings Distributions for Buildings in a Utility’s Service Area

Several companies, universities, and national laboratories are developing urban-scale energy modeling that allows the creation of a digital twin of buildings for the simulation and optimization of real-world, city-sized areas. Prior to simulation-based assessment, a baseline of savings for a set of utility-defined use cases was established to clarify the initial business case for specific energy efficient building technologies. In partnership with a municipal utility, 178,337 OpenStudio and EnergyPlus models of buildings in the utility’s 1400 km 2 service area were created, simulated, and assessed with measures for quantifying energy, demand, cost, and emissions reductions of each building. The method of construction and assumptions behind these models is discussed, definitions of example measures are provided, and distribution of savings across the building stock is provided under a maximum technical adoption scenario.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1999

Estimated Benefits of Variable-Geometry Wing Camber Control for Transport Aircraft

Analytical benefits of variable-camber capability on subsonic transport aircraft are explored. Using aerodynamic performance models, including drag as a function of deflection angle for control surfaces of interest, optimal performance benefits of variable camber are calculated. Results demonstrate that if all wing trailing-edge surfaces are available for optimization, drag can be significantly reduced at most points within the flight envelope. The optimization approach developed and illustrated for flight uses variable camber for optimization of aerodynamic efficiency (maximizing the lift-to-drag ratio). Most transport aircraft have significant latent capability in this area. Wing camber control that can affect performance optimization for transport aircraft includes symmetric use of ailerons and flaps. In this paper, drag characteristics for aileron and flap deflections are computed based on analytical and wind-tunnel data. All calculations based on predictions for the subject aircraft and the optimal surface deflection are obtained by simple interpolation for given conditions. An algorithm is also presented for computation of optimal surface deflection for given conditions. Benefits of variable camber for a transport configuration using a simple trailing-edge control surface system can approach more than 10 percent, especially for nonstandard flight conditions. In the cruise regime, the benefit is 1-3 percent.

Bolonkin, Alexander↗

NASA NTRS1982

Estimation of the sugar cane cultivated area from LANDSAT images using the two phase sampling method

A two phase sampling method and the optimal sampling segment dimensions for the estimation of sugar cane cultivated area were developed. This technique employs visual interpretations of LANDSAT images and panchromatic aerial photographs considered as the ground truth. The estimates, as a mean value of 100 simulated samples, represent 99.3% of the true value with a CV of approximately 1%; the relative efficiency of the two phase design was 157% when compared with a one phase aerial photographs sample.

Parada, N. D. J.↗

DOE OSTI2024

Morphological Modulation of TiO 2 Nanotube via Optimal Anodization Condition for Solar Water Oxidation

With the depletion of fossil fuels and the rising global demand for energy, photoelectrochemical (PEC) water splitting presents a promising solution to avert an energy crisis. Titanium dioxide (TiO 2 ), an n -type semiconductor, has gained popularity as a photoanode due to its remarkable PEC properties. Nevertheless, inherent challenges such as a wide band gap (~3.2 eV), charge recombination, and slow oxygen evolution reaction (OER) rates at the surface limit its practical application by constraining light absorption. To overcome these limitations, we have developed TiO 2 nanotubes (NTs) using a facile anodization method. This study examines the impact of anodization growth parameters on solar water oxidation performance. Specifically, TiO 2 NTs with modified anodization time (referred to as TiO 2 -6) showed a 3.5-fold increase in photocurrent density compared to the as-grown TiO 2 NTs. Furthermore, electrochemical analyses, such as electrochemical impedance spectroscopy (EIS), indicated a significant decrease in charge transfer resistance following the adjustment of on-off anodization time. Additionally, the TiO 2 -6 photoanode demonstrated a higher electrochemically active surface area (ECSA) than other samples. Therefore, optimal nanostructuring parameters are crucial for enhancing the PEC properties of TiO 2 NTs. Overall, our findings offer valuable insights for fabricating high-quality TiO 2 NTs photoanodes, contributing to developing efficient PEC systems for sustainable energy production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Machine Learning for Searching the Dark Energy Survey for Trans-Neptunian Objects

In this paper we investigate how implementing machine learning could improve the efficiency of the search for Trans-Neptunian Objects (TNOs) within Dark Energy Survey (DES) data when used alongside orbit fitting. The discovery of multiple TNOs that appear to show a similarity in their orbital parameters has led to the suggestion that one or more undetected planets, an as yet undiscovered “Planet 9”, may be present in the outer solar system. DES is well placed to detect such a planet and has already been used to discover many other TNOs. Here, we perform tests on eight different supervised machine learning algorithms, using a data set consisting of simulated TNOs buried within real DES noise data. We found that the best performing classifier was the Random Forest which, when optimized, performed well at detecting the rare objects. We achieve an area under the receiver operating characteristic (ROC) curve, (AUC) = 0.996 ± 0.001. After optimizing the decision threshold of the Random Forest, we achieve a recall of 0.96 while maintaining a precision of 0.80. Finally, by using the optimized classifier to pre-select objects, we are able to run the orbit-fitting stage of our detection pipeline five times faster.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2022

Estimating List-Mode Data Sensitivities to Nuclear Data with MCNP6

Nuclear data are a vital component of predictive simulations used in applications like experiment design, stockpile stewardship, nuclear nonproliferation/safeguards, health physics, and criticality safety. A singular simulation requires the coalescence of different areas of nuclear data such as cross sections, angular distributions, and energy distributions of emitted neutrons for different materials and energy ranges. Improving nuclear data and thus reducing the uncertainty in simulated parameters could enable smaller, better-informed safety factors and ultimately reduce operational and procedural costs. There is a constant effort to garner a better understanding of the physical quantities represented by nuclear data through experiments. Integral experiment benchmarks use simulated and measured results to validate current nuclear data values. In the past, benchmarks primarily focused on the effective multiplication factor (k eff ); however, this limited scope has caused compensating errors and areas of nuclear data that lack validation. Compensating errors are inaccuracies in nuclear data that are obfuscated by cancellation when observing integrated values such as k eff . Diverse integral benchmark experiments that look for quantities of interest other than k eff and include multiple responses minimize the possibility of compensating errors and provides validation to areas of nuclear data previously lacking experimental validation. Benchmark experiments can be optimized during the design process to be highly dependent on specific areas of nuclear data. The dependence of a response in an experiment to a specific area/type of nuclear data is defined as sensitivity. A larger sensitivity means that nuclear data uncertainties will play a larger role in the response(s) resulting in larger bias. Currently, the sensitivity capabilities of the Monte Carlo N-Particle (MCNP ®1 ) transport code are limited to responses of k eff and tallied values (e.g., flux, surface current). As a part of the EUCLID project, this work explores estimating list-mode nuclear data sensitivities that can be used to design experiments aimed to constrain and reduce compensating errors in nuclear data by focusing on responses other than k eff . Tallied values are ideal quantities that are estimated with detectors during experiments. List-mode data (a list of neutron collection times) are the direct output of detector systems in subcritical neutron noise experiments. Expanding MCNP sensitivity capabilities to include the sensitivity of responses estimated from list-mode data, such as the prompt neutron decay constant (α) and multiplicity estimates (S and D), enables more direct comparison of simulated and measured experimental quantities. Additionally, deterministic tools such as SENSMG are capable of obtaining sensitivities to a wide variety of responses; however, these tools cannot handle complex geometries due to the assumptions made in discretizing the phase-space variables of the Boltzman transport equation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Parallel Multigrid in Time and Space for Extreme-Scale Computational Science: Chaotic and Hyperbolic Problems

The coming massive parallelism of exascale computing presents a pressing challenge for the many DOE simulations of time-dependent partial differential equations (PDEs), which typically use traditional sequential time stepping methods. Since this traditional approach is inherently serial, it presents a sequential bottleneck when moving to exascale computing, because future performance gains will come through greater concurrency, not faster clock speeds. Thus, the goal of this work is to research parallelism in time, i.e., methods that compute multiple time values simultaneously, not sequentially. The focus will be on hyperbolic and chaotic problems of interest to DOE, with the goal of enabling scalable simulations of time-dependent hyperbolic and chaotic problems on future architectures. The chosen methodology for solving these problems parallel-in-time is multigrid, because multigrid (when it works) is a powerful, optimal, and scalable solver for discretized PDEs. Multigrid is already commonly used in many DOE simulations for scalably and optimally solving space-only PDE problems. The areas of hyperbolic and chaotic problems are chosen because of their relevance to problems of programmatic interest to DOE. However, these problems are also well-known to be difficult for parallelin-time methods, with the most common method, parareal, diverging in many cases. The current stateof-the-art for parallel-in-time at LLNL is the multigrid reduction in time (MGRIT) XBraid package, which also struggles for such problems, while still showing some improvement over parareal. In summary, new methods are needed for an efficient parallel-in-time scheme for hyperbolic and chaotic problems, and this work shall research promising new multigrid methods in this area. In particular, we take inspiration from the Least Squares Shadowing (LSS by Wang) approach for solving chaotic problems. Here, an optimization approach is able to find “well-conditioned” shadow trajectories/solutions to the original “ill-conditioned” chaotic problem. Thus, the new multigrid methods researched here also arise in an optimization context.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS2014

Aerodynamic Limits on Large Civil Tiltrotor Sizing and Efficiency

The NASA Large Civil Tiltrotor (2nd generation, or LCTR2) has been the reference design for avariety of NASA studies of design optimization, engine and gearbox technology, handling qualities, andother areas, with contributions from NASA Ames, Glenn and Langley Centers, plus academic and industrystudies. Ongoing work includes airfoil design, 3D blade optimization, engine technology studies, andwingrotor aerodynamic interference. The proposed paper will bring the design up to date with the latestresults of such studies, then explore the limits of what aerodynamic improvements might hope toaccomplish. The purpose is two-fold: 1) determine where future technology studies might have the greatestpayoff, and 2) establish a stronger basis of comparison for studies of other vehicle configurations andmissions.

Large Civil Tiltrotor↗

NASA NTRSDate not supplied

Determining Optimal Asset Location for Rapid and Efficient Wildfire Suppression: A Simulation-Based Approach

The impact of wildfire incidents has been growing in recent years, posing a serious threat to communities at the urban-wildland interface. To address this problem, there have been growing calls to use UAVs to increase the capacity of responsible agencies to quickly and effectively suppress fires and to reduce risks associated with firefighting. One of the opportunities associated with UAVs is the ability to rapidly and autonomously operate from limited-access air bases where fires are expected to burn. This study provides an approach to determine where these air bases should be placed in order to most rapidly extinguish fires, given provided fuel distributions. This approach uses an integrated simulation of fire propagation and UAV-based suppression actions to determine how much of a given environment was burned over a range of scenarios. It then uses an optimization method to explore the space and determine the location with the least burned area. Results show the approach to efficiently and effectively provide optimal bases for single-base placements over a range of scenarios, though future work is required to adequately calibrate the model and study how it can be used in multiple-base placement problems.

Daniel Hulse↗

NASA NTRSDate not supplied

Determining Optimal Asset Location for Rapid and Efficient Wildfire Suppression: A Simulation-Based Approach

Daniel Hulse↗