Search NASA⌕ Search

SEARCH · Search NASA

Results for “augmentation systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Aerodynamic Characteristics of a Large-Scale Unswept Wing-Body-Tail Configuration with Blowing Applied Over the Flap and Wind Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the effects of a blowing boundary-layer-control lift-augmentation system on the aerodynamic characteristics of a large-scale model of a fighter-type airplane. The wing was unswept at the 70-percent- chord station, had an aspect ratio of 2.86, a taper ratio of 0.40, and 4-percent-thick biconvex airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack from approximately -4 deg to 23 deg for a Reynolds number of approximately 5.2 x 10(exp 6) which corresponds to a Mach number of 0.08. Blowing rates were normally restricted to values just sufficient to control air-flow separation. The results of this investigation showed that wing leading-edge blowing in combination with large values of wing leading-edge-flap deflection was a very effective leading-edge flow-control device for wings having highly loaded trailing-edge flaps. With leading-edge blowing there was no hysteresis of the lift, drag, and pitching-moment characteristics upon recovery from stall. End plates were found to improve the lift and drag characteristics of the test configuration in the moderate angle-of-attack range, and blockage to one-quarter of the blowing-slot area was not detrimental to the aerodynamic characteristics. Blowing boundary-layer control resulted in a considerably reduced landing speed and reduced landing and take-off distances. The ailerons were very effective lateral-control devices when used with blowing flaps.

McLemore, H. Clyde↗
NASA NTRS1999

Constitutive and Stability Behavior of Granular Materials Under Very Low Effective Stresses

The study of the behavior of granular materials such as sand is of great importance to the understanding of the response of foundations resting on surface and near-surface soil deposits. A clear understanding of the behavior of such materials can also provide insights into other related issues where low effective stresses are encountered such as liquefaction. The main sources of the constitutive and stability properties of cohesionless granular materials is interparticle friction, which in turn under low confinement stress levels is strongly affected by gravitational body forces under terrestrial (1 gravity) conditions. Under moderate-to-high stress levels, the influence of gravity on the behavior of experiments may not be pronounced and therefore the test results in a terrestrial environment may be acceptable for engineering purposes. However, the conduct of experiments on granular materials under very low stress levels and under quasi-static conditions can only be performed in a microgravity environment. A series of displacement-controlled cyclic triaxial compression experiments were performed in a SPACEHAB module on the Space Shuttle during the STS-79 mission to Mir in September, 1996, and the STS-89 mission in January, 1998. The experiments were conducted on six right cylindrical specimens 75 mm in diameter and 150 mm long at effective confining pressures of 0.05, 0.52 and 1.30 kPa. The results show very high peak strength friction angles in the range of 47.6 to 70.0 degrees, which are mainly due to overconsolidation and grain interlocking effects. It was observed that the residual strength levels were in the same range as that observed at higher confining stress levels. The dilatancy angles were unusually high in the range of 30 to 31 degrees. All specimens display substantial initial stiffnesses and elastic moduli during unloading and reloading events, which are nearly an order of magnitude higher than conventional theories predict. A periodic instability phenomenon which appears to result from buckling of multiple internal arches and columnar systems, augmented by stick-slips was observed in the experiments. Computed Tomography (CT) measurements revealed valuable data about the internal fabric and the specimens deformation patterns. Uniform diffuse bifurcation with multiple radial shear bands was observed in the specimens tested in a microgravity environment. In the axial direction, two major conical surfaces were developed. Spatial nonsymmetrical deformations were observed in specimens tested in terrestrial laboratory.

Alshibli, Khalid A.↗
NASA NTRS1998

Mechanics of Granular Materials (MGM) Microgravity Experiment

The second series of MGM experiment was conducted during the STS-89 mission in January 1998. The experiment was previously flow on Atlantis's STS-79 mission in September 1996. Six displacement-controlled, drained triaxial compression experiments were performed at very low effective confining stresses. The confining stresses were in the ranges 0.05, 0.52 and 1.30 kPa. Three experiments were subjected to monotonic loading and unloading cycles while the other three experiments were subjected to cyclic loading. The results show very high peak strength friction angles in the range of 47.6 to 70.0 degrees, which are mainly due to overconsolidation and grain interlocking effects. It was observed that the residual strength levels in the monotonic loading experiments were in the same range as that observed at higher confining stress levels. The dilatancy angles were unusually high in the range of 30 to 31 degrees. All specimens display substantial initial stiffnesses and elastic moduli during unloading and reloading events, which are nearly an order of magnitude higher than conventional theories predict. A periodic instability phenomenon which appears to result from buckling of multiple internal arches and columnar systems, augmented by stick-slips was observed in the experiments. Computed Tomography (CT) measurements revealed valuable data about the internal fabric and the specimens deformation patterns. Uniform diffuse bifurcation with multiple radial shear bands was observed in the specimens tested in a microgravity environment. In the axial direction, two major conical surfaces were developed. Spatial nonsymmetrical deformations were observed in specimens tested in terrestrial laboratory.

Alshibli, Khalid A.↗
NASA NTRS1997

Transfer of the CONSOL-OPTCAD Rotorcraft Design Tool to Industry

Significant progress was made. Initial results on the improvement of the user-friendliness and useability of GIFCORCODE led to the decision to provide GIFCORCODE with a menu-driven user interface. In collaboration with staff at Moffett field and students from Cal Poly this objective has been largely met. GIFCORCODE is now menu-driven and very much easier to use. Complete designs for stability and control augmentation systems for the UH-60A ADOCS/RASCAL rotorcraft in both hover and 80 knots forward flight have been completed and documented. The originally planned presentations to industry were deferred so the new user interface for GIFCORCODE could be completed. The industry presentations are now planned for the next year. Similarly, the work on preparing a short course on the use of GIFCORCODE was deferred. The details of the original goals for this contract are presented in this report. The modifications to these goals and the reasons for them are also described. This is followed by a section containing the results of work on this contract. A final section, conclusions, contains suggestions for future work on this project.

Levine, William S.↗
NASA NTRS1999

Navigating the Airways

Through a licensing agreement with JPL, Hughes Aircraft Company is using the Jet Propulsion Laboratory's (JPL) software GIPSY-OASIS for implementation of the Federal Aviation Administration's Wide Area Augmentation System (WAAS). WAAS will provide precision navigation for commercial airliners in U.S. airspace. JPL's GIPSY-OASIS (GIPSY - GPS-Inferred Positioning System; OASIS - Orbit Analysis and Simulation Software) has been used world-wide to produce the most accurate Global Positioning System (GPS) ephemeredes (satellite position) solutions ever achieved for ground and space users, both in scientific and commercial applications.

Source record↗
NASA NTRS2003

Piloted Evaluation of Modernized Limited Authority Control Laws in the NASA-Ames Vertical Motion Simulator (VMS)

The UH-60 BLACK HAWK was designed in the 1970s, when the US Army primarily operated during the day in good visual conditions. Subsequently, the introduction of night-vision goggles increased the BLACK HAWK'S mission effectiveness, but the accident rate also increased. The increased accident rate is strongly tied to increased pilot workload as a result of a degradation in visual cues. Over twenty years of research in helicopter flight control and handling qualities has shown that these degraded handling qualities can be recovered by modifying the response type of the helicopter in low speed flight. Sikorsky Aircraft Corporation initiated a project under the National Rotorcraft Technology Center (NRTC) to develop modern flight control laws while utilizing the existing partial authority Stability Augmentation System (SAS) of the BLACK HAWK. This effort resulted in a set of Modernized Control Laws (MCLAWS) that incorporate rate command and attitude command response types. Sikorsky and the US Army Aeroflightdynamics Directorate (AFDD) conducted a piloted simulation on the NASA-Ames Vertical h4otion Simulator, to assess potential handling qualities and to reduce the risk of subsequent implementation and flight test of these modern control laws on AFDD's EH-60L helicopter. The simulation showed that Attitude Command Attitude Hold control laws in pitch and roll improve handling qualities in the low speed flight regime. These improvements are consistent across a range of mission task elements and for both good and degraded visual environments. The MCLAWS perform better than the baseline UH-60A control laws in the presence of wind and turbulence. Finally, while the improved handling qualities in the pitch and roll axis allow the pilot to pay more attention to the vertical axis and hence altitude performance also improves, it is clear from pilot comments and altitude excursions that the addition of an Altitude Hold function would further reduce workload and improve overall handling qualities of the aircraft.

Sahasrabudhe, Vineet↗
NASA NTRS2005

On a Slow Roll

Satellite navigation and surveillance products and services can cut costs, improve accuracy, expand coverage and enhance safety. But the global transformation of air traffic management (ATM) that satellites and ground augmentation systems have promised is being realized much more slowly than expected. "There are still a lot of nations that could benefit [from satellite navigation and surveillance] that haven't invested dime in new equipment." says Tim Katanik, manager of business development for navigation and landing systems Raytheon. But then things usually move slowly in this industry, he adds.

Hughes, David↗
NASA NTRS2005

The Implications of Handling Qualities in Civil Helicopter Accidents Involving Hover and Low Speed Flight

Because of increasing accident rates in Army helicopters in hover and low speed flight, a study was made in 1999 of accidents which could be attributed to inadequate stability augmentation. A study of civil helicopter accidents from 1993-2004 was then undertaken to pursue the issue of poor handling qualities in helicopters which, in almost all cases, had no stability augmentation. The vast majority of the mishaps studied occurred during daylight in visual meteorological condition, reducing the impact of degraded visual environments (DVE) on the results. Based on the Cooper-Harper Rating Scale, the handling qualities of many of the helicopters studied could be described as having from "very objectionable" to "major" deficiencies. These costly deficiencies have resulted in unnecessary loss of life, injury, and high dollar damage. Low cost and lightweight augmentation systems for helicopters have been developed in the past and are still being investigated. They offer the potential for significant reductions in the accident rate.

Dugan, Daniel C.↗
NASA NTRS2007

Generating high precision ionospheric ground-truth measurements

A method, apparatus and article of manufacture provide ionospheric ground-truth measurements for use in a wide-area augmentation system (WAAS). Ionospheric pseudorange/code and carrier phase data as primary observables is received by a WAAS receiver. A polynomial fit is performed on the phase data that is examined to identify any cycle slips in the phase data. The phase data is then leveled. Satellite and receiver biases are obtained and applied to the leveled phase data to obtain unbiased phase-leveled ionospheric measurements that are used in a WAAS system. In addition, one of several measurements may be selected and data is output that provides information on the quality of the measurements that are used to determine corrective messages as part of the WAAS system.

Komjathy, Attila↗
NASA NTRS2011

Commercially Hosted Government Payloads: Lessons from Recent Programs

In a commercially hosted operational mode, a scientific instrument or operational device is attached to a spacecraft but operates independently from the spacecraft s primary mission. Despite the expected benefits of this arrangement, there are few examples of hosted payload programs actually being executed by government organizations. The lack of hosted payload programs is largely driven by programmatic challenges, both real and perceived, rather than by technical challenges. Partly for these reasons, NASA has not sponsored a hosted payload program, in spite of the benefits and visible community interest in doing so. In the interest of increasing the use of hosted payloads across the space community, this paper seeks to alleviate concerns about hosted payloads by identifying these programmatic challenges and presenting ways in which they can be avoided or mitigated. Despite the challenges, several recent hosted payload programs have been successfully completed or are currently in progress. This paper presents an assessment of these programs, with a focus on acquisition, costs, schedules, risks, and other programmatic aspects. The hosted payloads included in this study are the Federal Aviation Administration's Wide Area Augmentation System (WAAS) payloads, United States Coast Guard's Automatic Identification System (AIS) demonstration payload, Department of Defense's IP Router In Space (IRIS) demonstration payload, the United States Air Force's Commercially Hosted Infrared Payload (CHIRP), and the Australian Defence Force's Ultra High Frequency (UHF) payload. General descriptions of each of these programs are presented along with issues that have been encountered and lessons learned from those experiences. A set of recommended approaches for future hosted payload programs is presented, with a focus on addressing risks or potential problem areas through smart and flexible contracting up front. This set of lessons and recommendations is broadly applicable to future hosted payload programs, whether they are technology demonstrations, communications systems, or operational sensors. Additionally, we present a basic cost model for commercial access to space for hosted payloads as a function of payload mass

Andraschko, Mark A.↗
NASA NTRS2014

Incorporating Handling Qualities Analysis into Rotorcraft Conceptual Design

This paper describes the initial development of a framework to incorporate handling qualities analyses into a rotorcraft conceptual design process. In particular, the paper describes how rotorcraft conceptual design level data can be used to generate flight dynamics models for handling qualities analyses. Also, methods are described that couple a basic stability augmentation system to the rotorcraft flight dynamics model to extend analysis to beyond that of the bare airframe. A methodology for calculating the handling qualities characteristics of the flight dynamics models and for comparing the results to ADS-33E criteria is described. Preliminary results from the application of the handling qualities analysis for variations in key rotorcraft design parameters of main rotor radius, blade chord, hub stiffness and flap moment of inertia are shown. Varying relationships, with counteracting trends for different handling qualities criteria and different flight speeds are exhibited, with the action of the control system playing a complex part in the outcomes. Overall, the paper demonstrates how a broad array of technical issues across flight dynamics stability and control, simulation and modeling, control law design and handling qualities testing and evaluation had to be confronted to implement even a moderately comprehensive handling qualities analysis of relatively low fidelity models. A key outstanding issue is to how to 'close the loop' with an overall design process, and options for the exploration of how to feedback handling qualities results to a conceptual design process are proposed for future work.

Analysis into Rotorcraft↗
NASA NTRS2015

Ionospheric Mapping Software Ensures Accuracy of Pilots GPS

IonoSTAGE and SuperTruth software are part of a suite created at the Jet Propulsion Laboratory to enable the Federal Aviation Administration's Wide Area Augmentation System, which provides pinpoint accuracy in aircraft GPS units. The system, used by more than 73,000 planes, facilitates landings under adverse conditions at small airports. In 2013, IonoSTAGE and SuperTruth found their first commercial license when NEC, based in Japan, with US headquarters in Irving, Texas, licensed the entire suite.

Source record↗
NASA NTRS2018

Propulsion System Options for a Potential Sample Return Lander (SRL) for Mars

A potential Mars Sample Return (MSR) campaign would be very unique challenge and has been the focus of technology development and planning efforts at JPL for several decades. The latest mission concept study focuses on a potential Sample Return Lander (SRL). The potential SRL examined several propulsion system approaches using monopropellant and bi-propellants for the terminal descent phase. A ranking was developed based on a mathematical optimization program. This paper focuses on the evaluations conducted for these system options. Historically, monopropellant and bi-propellant propulsion systems are usually considered for this application; this study took a fresh look at both conventional State of the Art (SOA) pressure fed monopropellant and bi-propellant propulsion system and augmenting the system using small Electrically Driven Pumps (EDP) for both these propulsion systems.

Preudhomme, Michael↗
NASA NTRS2021

The spatial distribution of ionospheric threats to WAAS integrity, 2000 – 2019: a systematic analysis

The United States’ Wide Area Augmentation System (WAAS) broadcasts data to facilitate aircraft navigation. This paper examines the spatial dependence of ionospheric disturbances that have threatened the accuracy and reliability of position estimates derived from these data over the period 2000 – 2019. We address two distinct aspects of this spatial dependence: (1) the geographic distribution of these threats, in particular, in relation to geomagnetic latitude, and (2) the geometric dependence of threats relative to the locations of the receiver sites that comprise the WAAS network. We analyze threat distributions in terms of the various means that WAAS employs to mitigate these threats, including the Extreme Storm Detector, the Moderate Storm Detector, local irregularity detectors, and the ionospheric threat model. Distinct distributions are presented for threats occurring in Solar Cycle 23 and those of Solar Cycle 24. To study the geometric dependence of threats on receiver locations, we use as a metric the distance separating a threat from the centroid of the nearest Ncentroid receivers. Large values of this metric identify threats at or beyond the edge of coverage. We conclude by discussing the implications of our results for WAAS operations.

Altshuler, Eric↗
NASA NTRSDate not supplied

Analyses of the Boeing 737-MAX Accidents: Formal Models and Psychological Perspectives

Two fatal accidents involving the B737MAX resulted from the flight crews’ inability to overcome the effects of the Maneuvering Characteristics Augmentation System (MCAS). MCAS was designed to mimic the control column feel pressure and pitching behavior of the B737NG, which was the certification basis for the B737MAX. We briefly describe the potential role of formally modeling different perspectives during system design, and how such modeling can reveal gaps and conflicts between perspectives. We also discuss some of the relevant human factors issues involved in these accidents and how the aircraft’s behavior may have affected the pilots’ psychological states. Implications for automation design are considered.

5737MAX↗
DOE OSTI2022

Scalable Energy System Expansion Under Uncertainty Using Multi-Stage Stochastic Optimization

The intermittent nature of power from renewable energy sources poses new challenges for electrical grids. This is due to the variable and uncertain nature of the power output from these resources. These features of renewable generation are becoming more relevant to energy system planning as grids reach higher penetration levels of renewable energy. In this presentation we present approaches for energy system planning based on scalable computational approaches which enable the explicit consideration of operational uncertainties in the planning process. Using multi-stage stochastic programming and the progressive hedging algorithm, we compute energy system expansion decisions on modified versions of the RTS-GMLC test system augmented with large amounts of renewable generation.

MATHEMATICS AND COMPUTING↗
NASA NTRS1984

Leading edge flap system for aircraft control augmentation

Traditional roll control systems such as ailerons, elevons or spoilers are least effective at high angles of attack due to boundary layer separation over the wing. This invention uses independently deployed leading edge flaps on the upper surfaces of vortex stabilized wings to shift the center of lift outboard. A rolling moment is created that is used to control roll in flight at high angles of attack. The effectiveness of the rolling moment increases linearly with angle of attack. No adverse yaw effects are induced. In an alternate mode of operation, both leading edge flaps are deployed together at cruise speeds to create a very effective airbrake without appreciable modification in pitching moment. Little trim change is required.

Rao, D. M.↗