Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalytic temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Hydrogen Peroxide-Water-Ethanol Monopropellant Blend for CubeSat Propulsion

Monopropellant propulsion that provides high performance and low hazards compared to state-of-art hydrazine are being investigated under NASA, DOD and commercially sponsored green propellant research and development programs. This NASA effort looks at phosphate stabilized 50% hydrogen peroxide/water –ethanol blends to evaluate their stability and combustion behavior in submillimeter diameter microtube combustion apparatus for cubesat propulsion applications. Exploratory 7-day stability tests find no pressure rise in a sealed test tube environment at room temperature indicating at least short term stability of the mixture. Temperature rise during combustion testing in resistively heated nickel microtube apparatus shows that micro-combustion is achieved in the tube. Propellant density is approximately 1.2 g/cu.cm compared to 1.0 g/cu.cm for hydrazine. Theoretical specific impulse of the stoichiometric blend is 219 s at a chamber pressure of 20 psia and an area ratio of 30:1. Density-specific impulse of this blend is 263 s while hydrazine is only about 215-220 s in small reaction control system thrusters. This provides about 20-22% more density-specific impulse for the cube sat compared to hydrazine. The the oretical combustion temperature is 2168°F, which is thermally compatible with stainless steel materials of construction and the nickel catalyst used in the tests. Combustion test results are given for stoichiometric, as well as fuel-lean and fuel-rich propellant formulations. These tests focus on thermally and catalytically supported combustion in the microtube, which requires a microtube preheat temperature of about 900°F and sufficient residence time to achieve combustion that is stable and anchored in the tube without blowing through the tube unreacted. Thrust class is expected to be in the 10 m N range based on flow rate and estimated specific impulse. Power requirements are generally below 25 W to heat the tube. Steady state combustion testing is typically conducted for 3 minutes and shows little degradation of the hardware over multiple test cycles indicating that there is little catalyst degradation over time and little catalyst deactivation due to the phosphate stabilizer in the hydrogen peroxide.

Monopropellant↗
NASA NTRS1985

A color graphics presentation of the Space Shuttle Orbiter windward surface entry temperature distribution

The windward surface temperature response measured during the fifth entry of the Space Shuttle Columbia is presented as solid filled color contour plots. These plots show the data from 92 instruments, at selected points in time, in a manner which makes the temperature extremes and gradients immediately obvious. Several physical phenomena, such as separated flow caused by the deflected body flap, local heating at the elevon-elevon gap, an overview of the propagation of boundary-layer transition over the Orbiter windward surface, and the thermal response of eight catalytically coated tiles, can be observed or inferred from the displayed temperatures. In addition, the maximums from each instrument have been contoured and are presented with a companion plot showing the percentage of surface area covered by each contour level. Also, the flight data are presented using the colors which correspond to the surface emittance as a function of temperature. To show the temperature transients, a computer-generated movie has been produced showing the temperature contours from 100 s to 1500 s after entry interface.

Martin, F. W., Jr.↗
DOE OSTI2024

Alumina–Titania Nanolaminate Condensers for Hot Programmable Catalysis

Nanolaminates composed of thin alternating layers of Al2O 3 and TiO 2 (ATO) were engineered by using atomic layer deposition as the dielectric material for a Pt-on-carbon catalytic condenser. Investigation assessed synthesis parameters including the deposition temperature, Al 2 O 3 and TiO 2 layer thicknesses, total number of layers, and a capping Al 2 O 3 layer on the maximum charge accumulation in the Pt catalyst. The highest capacitance ATO configuration demonstrated a specific capacitance of ∼1200 nF/cm 2 with working voltages of ±5 V, enabling the storage of 4 × 10 13 electrons or holes per cm 2 at room temperature. The ATO devices exhibited enhanced capacitance at elevated temperatures of up to 400 °C, suggesting the suitability of these materials for high-temperature applications. Adsorption of carbon monoxide on the Pt/C-ATO device characterized by grazing incidence infrared spectroscopy showed changes in the surface binding energy of 13.1 ± 0.8 kJ/mol for an applied external voltage bias of ±1 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Surface oxygenation of multicomponent nanoparticles toward active and stable oxidation catalysts

Abstract The need for active and stable oxidation catalysts is driven by the demands in production of valuable chemicals, remediation of hydrocarbon pollutants and energy sustainability. Traditional approaches focus on oxygen-activating oxides as support which provides the oxygen activation at the catalyst-support peripheral interface. Here we report a new approach to oxidation catalysts for total oxidation of hydrocarbons (e.g., propane) by surface oxygenation of platinum (Pt)-alloyed multicomponent nanoparticles (e.g., platinum-nickel cobalt (Pt–NiCo)). The in-situ/operando time-resolved studies, including high-energy synchrotron X-ray diffraction and diffuse reflectance infrared Fourier transform spectroscopy, demonstrate the formation of oxygenated Pt–NiOCoO surface layer and disordered ternary alloy core. The results reveal largely-irregular oscillatory kinetics associated with the dynamic lattice expansion/shrinking, ordering/disordering, and formation of surface-oxygenated sites and intermediates. The catalytic synergy is responsible for reduction of the oxidation temperature by ~100 °C and the high stability under 800 °C hydrothermal aging in comparison with Pt, and may represent a paradigm shift in the design of self-supported catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fast product release requires active-site water dynamics in carbonic anhydrase

Water plays an essential role in enzyme structure, stability, and the substantial rate enhancement of enzyme catalysis. However, direct observations linking enzyme catalysis and active-site water dynamics pose a significant challenge due to experimental difficulties. By integrating an ultraviolet (UV) photolysis technique with temperature-controlled X-ray crystallography, we track the catalytic pathway of carbonic anhydrase II (CAII) at 1.2 Å resolution. This approach enables us to construct molecular movies of CAII catalysis, encompassing substrate (CO 2 ) binding, conversion from substrate to product (bicarbonate), and product release. In the catalytic pathway, we identify an unexpected configuration in product binding and correlate it with sub-nanosecond rearrangement of active-site water. Based on these experimental observations, we propose a comprehensive mechanism of CAII and describe the detailed structure and dynamics of active-site water in CAII. Our findings suggest that CAII has evolved to utilize the structure and fast dynamics of the active-site waters for its diffusion-limited catalytic efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Organo-catalyzed deamination of polystyrene sulfonamide for diverse post-polymerization modification of styrenic polymers

Post-polymerization modification allows for the incorporation of functional groups that would otherwise be incompatible with polymerization conditions, enhancing synthetic efficiency and facilitating the creation of complex polymer architectures for specialized applications, such as biomedical devices, electronics, and advanced coatings. Herein, we report a method inspired by late-stage functionalization of small molecules for the post-polymerization modification of aromatic polymers, specifically polystyrene (PS), under mild reaction conditions. First, PS was converted to polystyrene sulfonamide (PSSNH 2 ) with an 85% yield using established procedures. PSSNH 2 was subsequently transformed into a reactive sulfinate by deamination using an N-heterocyclic carbene (NHC) catalyst and benzaldehyde. The catalytic process was optimized by varying catalysts, solvents, bases, temperatures, and reaction times. The highest degree of deamination was 88% with a bicyclic NHC and K 2 CO 3 base in DMSO for 18 hours at 120 °C. The reactive sulfinate was then treated with various functional reagents, resulting in a library of aromatic polymers with different substituents with high degrees of functionalization ranging from 74% to 98%. Similarly, we modified expanded PS waste with trifluorobutyl iodide with a degree of functionalization of 72%, highlighting a new avenue for plastic upgrading. This approach could be used to rapidly generate functionalized polymers from PS with potential applications, including antibacterial properties and flame retardancy.

Shrestha, Tulaja [Univ. of Delaware, Newark, DE (U↗
NASA NTRS1975

Formation of nucleoside 5'-polyphosphates from nucleotides and trimetaphosphate

Nucleoside 5'-polyphosphates (N5PP) formed when solutions of nucleoside 5'-phosphates (N5P) and trimetaphosphate (TMP) are dessicated at room temperature are studied by paper chromatography, electrophoresis, and metal catalytic reactions. Divalent Mg ion exhibited superior catalytic function to other divalent metal ions in the reaction. Major reaction products are indicated. The importance of the N5PP series, TMP, and N5-triphosphate as substrates of RNA and DNA synthesis, and under postulated prebiotic conditions likely to obtain during prebiological ages of the earth, is emphasized and discussed. Alternate drying and wetting, evaporation from a prebiotic puddle, concentration of solubles in the remaining liquid phase, metal catalysis, and the role of these substances in the formation of amino acids and long-chain polyphosphates are considered.

Lohrmann, R.↗
NASA NTRS1983

Calcium Modulation of Plant Plasma Membrane-Bound Atpase Activities

The kinetic properties of barley enzyme are discussed and compared with those of other plants. Possibilities for calcium transport in the plasma membrane by proton pump and ATPase-dependent calcium pumps are explored. Topics covered include the ph phase of the enzyme; high affinity of barley for calcium; temperature dependence, activation enthalpy, and the types of ATPase catalytic sites. Attention is given to lipids which are both screened and bound by calcium. Studies show that barley has a calmodulin activated ATPase that is found in the presence of magnesium and calcium.

Caldwell, C.↗
NASA NTRS1990

Thermal emission spectroscopy of the middle atmosphere

The general objective of this research is to obtain, via remote sensing, simultaneous measurements of the vertical distributions of stratospheric temperature, ozone, and trace constituents that participate in the catalytic destruction of ozone (NO(sub y): NO, NO2, NO3, HNO3, ClONO2, N2O5, HNO4; Cl(sub x): HOCl), and the source gases for the catalytic cycles (H2O, CH4, N2O, CF2Cl2, CFCl3, CCl4, CH3Cl, CHF2Cl, etc.). Data are collected during a complete diurnal cycle in order to test our present understanding of ozone chemistry and its associate catalytic cycles. The instrumentation employed is an emission-mode, balloon-borne, liquid-nitrogen-cooled Michelson interferometer-spectrometer (SIRIS), covering the mid-infrared range with a spectral resolution of 0.020 cm(exp -1). Cryogenic cooling combined with the use of extrinsic silicon photoconductor detectors allows the detection of weak emission features of stratospheric gaseous species. Vertical distributions of these species are inferred from scans of the thermal emission of the limb in a sequence of elevation angles. The fourth SIRIS balloon flight was carried out from Palestine, Texas on September 15-16, 1986 with 9 hours of nighttime data (40 km). High quality data with spectral resolution 0.022 cm(exp -1), were obtained for numerous limb sequences. Fifteen stratospheric species have been identified to date from this flight: five species from the NO(sub y) family (HNO3, NO2, NO, ClONO2, N2O5), plus CO2, O3, H2O, N2O, CH4, CCl3F, CCl2F2, CHF2Cl, CF4, and CCl4. The nighttime values of N2O5, ClONO2, and total odd nitrogen have been measured for the first time, and compared to model results. Analysis of the diurnal variation of N2O5 within the 1984 and 1986 data sets, and of the 1984 ClONO2 measurements, were presented in the literature. The demonstrated ability of SIRIS to measure all the major NO(sub y) species, and therefore to determine the partitioning of the nitrogen family over a continuous diurnal cycle, is a powerful tool in the verification and improvement of photochemical modeling.

Kunde, V. G.↗
NASA NTRS1994

Effect of Porosity on Surface Catalytic Efficiency

This paper describes the effect of surface porosity of thermal protection materials on surface catalytic efficiency using test data taken from both arc-jet and side-arm reactor facilities. Relative surface porosity of the samples varied from 6% to 50%. Surface porosity was measured using a flow apparatus and Bernoulli equation. The surface catalytic efficiency of the materials was calculated using aerothermodynamic, and kinetic theories. The catalytic efficiency of the materials are compared at surface temperatures between room temperature and 2500 F. The data are presented in the form of graphs and tables.

Stewart, David A.↗
NASA NTRS2002

Carbon Nanotubes Growth by CVD on Graphite Fibers

Due to the superior electrical and mechanical properties of carbon nanotubes (CNT), synthesizing CNT on various substances for electronics devices and reinforced composites have been engaged in many efforts for applications. This presentation will illustrate CNT synthesized on graphite fibers by thermal CVD. On the fiber surface, iron nanoparticles as catalysts for CNT growth are coated. The growth temperature ranges from 600 to 1000 C and the pressure ranges from 100 Torr to one atmosphere. Methane and hydrogen gases with methane content of 10% to 100% are used for the CNT synthesis. At high growth temperatures (greater than or equal to 900 C), the rapid inter-diffusion of the transition metal iron on the graphite surface results in the rough fiber surface without any CNT grown on it. When the growth temperature is relative low (650-800 C), CNT with catalytic particles on the nanotube top ends are fabricated on the graphite surface. (Methane and hydrogen gases with methane content of 10% to 100% are used for the CNT synthesis.) (By measuring the samples) Using micro Raman spectroscopy in the breath mode region, single-walled or multi-walled CNT (MWCNT), depending on growth concentrations, are found. Morphology, length and diameter of these MWCNT are determined by scanning electron microscopy and Raman spectroscopy. The detailed results of syntheses and characterizations will be discussed in the presentation.

Zhu, Shen↗
DOE OSTI2021

Enzymes and Models. In: XAFS Techniques for Catalysts, Nanomaterials, and Surfaces

Many important redox-active metalloenzymes consist of 3d transition metals in their active sites. They catalyze multi-electron reactions in aqueous solution, under ambient temperature and pressure. To understand the functionality of the catalytic sites of these enzymes, X-ray spectroscopy methods provide important information of the electronic structure of the metal of interest and its local structural information, as well as their changes during the catalysis. Studying model compounds, that mimic enzyme catalytic site structures or their functional mimics, is as critical as studying enzymes themselves, in order to interpret X-ray spectroscopic data. In this chapter, various X-ray spectroscopic methods that are useful for structural and electronic structural studies of enzymes and model compounds are described.

Yachandra, VK↗
DOE OSTI2021

Bridging Thermal Catalysis and Electrocatalysis: Catalyzing CO 2 Conversion with Carbon‐Based Materials

Abstract Understanding the differences between reactions driven by elevated temperature or electric potential remains challenging, largely due to materials incompatibilities between thermal catalytic and electrocatalytic environments. We show that Ni, N‐doped carbon (NiPACN), an electrocatalyst for the reduction of CO 2 to CO (CO 2 R), can also selectively catalyze thermal CO 2 to CO via the reverse water gas shift (RWGS) representing a direct analogy between catalytic phenomena across the two reaction environments. Advanced characterization techniques reveal that NiPACN likely facilitates RWGS on dispersed Ni sites in agreement with CO 2 R active site studies. Finally, we construct a generalized reaction driving‐force that includes temperature and potential and suggest that NiPACN could facilitate faster kinetics in CO 2 R relative to RWGS due to lower intrinsic barriers. This report motivates further studies that quantitatively link catalytic phenomena across disparate reaction environments.

Koshy, David M.↗
NASA NTRS1990

Calorimetry, activity, and micro-FTIR analysis of CO chemisorption, titration, and oxidation on supported Pt

The value of in situ analysis on CO chemisorption, titration and oxidation over supported Pt catalysts using calorimetry, catalytic and micro-FTIR methods is illustrated using silica- and titania-supported samples. Isothermal CO-O and O2-CO titrations have not been widely used on metal surfaces and may be complicated if some oxide supports are reduced by CO titrant. However, they can illuminate the kinetics of CO oxidation on metal/oxide catalysts since during such titrations all O and CO coverages are scanned as a function of time. There are clear advantages in following the rates of the catalyzed CO oxidation via calorimetry and gc-ms simultaneously. At lower temperatures the evidence they provide is complementary. CO oxidation and its catalysis of CO oxidation have been extensively studied with hysteresis and oscillations apparent, and the present results suggest the benefits of a combined approach. Silica support porosity may be important in defining activity-temperature hysteresis. FTIR microspectroscopy reveals the chemical heterogeneity of the catalytic surfaces used; it is interesting that the evidence with regard to the dominant CO surface species and their reactivities with regard to surface oxygen for present oxide-supported Pt are different from those seen on graphite-supported Pt.

Sermon, Paul A.↗
DOE OSTI2020

Ni5Ga3 Catalysts for CO2 Reduction to Methanol: Exploring the Role of Ga Surface Oxidation/reductions on Catalytic Activity

Ad-Ni5Ga3/SiO2 catalyst, which is highly active and stable for thermal CO2 hydrogenation to methanol, was investigated to understand its surface dynamics during reaction conditions. The catalyst was prepared, tested and characterized using a multitude of techniques, including ex-situ XRD, TEM, H2-TPR, CO chemisorption and in-situ ETEM and APXPS. The formation of Ga2O3 upon air exposure was observed and the consequences on catalytic activity were investigated. Results revealed that upon air exposure Ga migrates from the subsurface region to the surface of the nanoparticles forming a Ga-oxide shell surrounding a metallic core. The oxide shell can be reduced completely at high temperatures and the temperature of the reduction activation treatment plays a crucial role on the catalytic activity. This air exposure-reduction procedure results in a redistribution of the Ga species in the surface/subsurface region, promoted by a higher Ga affinity for oxygen. XRD analysis of the post-reaction samples provide evidence for the partial transformation of a Ni5Ga3 intermetallic phase into a Ni-rich Ni3Ga phase. APXPS data indicate that the Ni-rich phase forms in the subsurface region. A Ga-rich phase exists on the surface, where the Ni/Ga ratio reaches 2/3 upon activation in hydrogen. At low reduction temperatures an amorphous Ga2O3 shell remains, indicating a promotion effect on methanol synthesis activity.

Ni-Ga, intermetallic, methanol synthesis, in-situ ↗
DOE OSTI2021

Bridging Thermal Catalysis and Electrocatalysis: Catalyzing CO 2 Conversion with Carbon-Based Materials

Understanding the differences between reactions driven by elevated temperature or electric potential remains challenging, largely due to materials incompatibilities between thermal catalytic and electrocatalytic environments. In this work, we show that Ni, N-doped carbon (NiPACN), an electrocatalyst for the reduction of CO 2 to CO (CO 2 R), can also selectively catalyze thermal CO 2 to CO via the reverse water gas shift (RWGS) representing a direct analogy between catalytic phenomena across the two reaction environments. Advanced characterization techniques reveal that NiPACN likely facilitates RWGS on dispersed Ni sites in agreement with CO 2 R active site studies. Finally, we construct a generalized reaction driving-force that includes temperature and potential and suggest that NiPACN could facilitate faster kinetics in CO 2 R relative to RWGS due to lower intrinsic barriers. This report motivates further studies that quantitatively link catalytic phenomena across disparate reaction environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Autoprocessing and oxyanion loop reorganization upon GC373 and nirmatrelvir binding of monomeric SARS-CoV-2 main protease catalytic domain

The monomeric catalytic domain (residues 1–199) of SARS-CoV-2 main protease (MPro 1-199 ) fused to 25 amino acids of its flanking nsp4 region mediates its autoprocessing at the nsp4-MPro 1-199 junction. We report the catalytic activity and the dissociation constants of MPro 1-199 and its analogs with the covalent inhibitors GC373 and nirmatrelvir (NMV), and the estimated monomer-dimer equilibrium constants of these complexes. Mass spectrometry indicates the presence of the accumulated adduct of NMV bound to MPro WT and MPro 1-199 and not of GC373. A room temperature crystal structure reveals a native-like fold of the catalytic domain with an unwound oxyanion loop (E state). In contrast, the structure of a covalent complex of the catalytic domain-GC373 or NMV shows an oxyanion loop conformation (E* state) resembling the full-length mature dimer. These results suggest that the E-E* equilibrium modulates autoprocessing of the main protease when converting from a monomeric polyprotein precursor to the mature dimer.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Active species in chloroaluminate ionic liquids catalyzing low-temperature polyolefin deconstruction

Abstract Chloroaluminate ionic liquids selectively transform (waste) polyolefins into gasoline-range alkanes through tandem cracking-alkylation at temperatures below 100 °C. Further improvement of this process necessitates a deep understanding of the nature of the catalytically active species and the correlated performance in the catalyzing critical reactions for the tandem polyolefin deconstruction with isoalkanes at low temperatures. Here, we address this requirement by determining the nuclearity of the chloroaluminate ions and their interactions with reaction intermediates, combining in situ 27 Al magic-angle spinning nuclear magnetic resonance spectroscopy, in situ Raman spectroscopy, Al K-edge X-ray absorption near edge structure spectroscopy, and catalytic activity measurement. Cracking and alkylation are facilitated by carbenium ions initiated by AlCl 3 - tert -butyl chloride (TBC) adducts, which are formed by the dissociation of Al 2 Cl 7 − in the presence of TBC. The carbenium ions activate the alkane polymer strands and advance the alkylation cycle through multiple hydride transfer reactions. In situ 1 H NMR and operando infrared spectroscopy demonstrate that the cracking and alkylation processes occur synchronously; alkenes formed during cracking are rapidly incorporated into the carbenium ion-mediated alkylation cycle. The conclusions are further supported by ab initio molecular dynamics simulations coupled with an enhanced sampling method, and model experiments using n-hexadecane as a feed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗