Search NASA⌕ Search

SEARCH · Search NASA

Results for “chromium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Metastable formation and disordering kinetics of body-centered orthorhombic CrNi 2 laths in a Cr-Ni binary alloy

Chromium (Cr) alloys combine low density with high-temperature strength but suffer from brittleness and rapid softening. Body-centered orthorhombic (BCO) CrNi 2 laths have been shown to improve Cr-alloy high-temperature strength retention, yet their thermal stability and transformation behavior remain unclear. CrNi 2 conventionally forms through long-range ordering from a face-centered cubic (FCC) phase. Using multiscale microscopy and neutron diffraction, we show that CrNi 2 instead nucleates from a body-centered cubic (BCC) matrix, in a binary Cr 85 Ni 15 alloy. Despite aging above the equilibrium ordering temperature, CrNi 2 persists for ∼220 h at 760 °C before fully disordering, indicating sluggish transformation kinetics. The formation and decomposition follow differing transformation pathways (BCC → CrNi 2 → FCC), revealing kinetic asymmetry not captured by equilibrium Cr-Ni phase diagrams. In conclusion, these findings redefine the transformation behavior of CrNi 2 , establish its metastable kinetic window, and suggest alloying strategies to stabilize CrNi 2 for precipitation strengthening of high-temperature Cr-alloys.

CrNi2 transformation kinetics↗
DOE OSTI2021

In situ preparation of visible-light-driven carbon quantum dots/NaBiO 3 hybrid materials for the photoreduction of Cr(VI)

Here, different carbon quantum dots (CQDs)/NaBiO 3 hybrid materials were synthesized as photocatalysts to effectively utilize visible light for the photocatalytic degradation of contaminants effectively. These hybrid materials exhibit an enhanced photocatalytic reduction of hexavalent chromium (Cr(VI)) in the aqueous medium. Zero-dimensional nanoparticles of CQDs were embedded within the two-dimensional NaBiO 3 nanosheets by the hydrothermal process. Compared with that of the pure NaBiO 3 nanosheets, the photocatalytic performance of the hybrid catalysts was significantly high and 6 wt.% CQDs/NaBiO 3 catalyst exhibited better photocatalytic performance. We performed the first-principles density functional theory calculations to study the interfacial properties of pure NaBiO 3 nanosheets and hybrid photocatalysts, and confirmed the CQDs played an important role in the CQDs/NaBiO 3 composites. The experimental results indicated that the enhanced reduction of Cr(VI) was probably due to the high loading of CQDs (electron acceptor) on NaBiO 3 , which made NaBiO 3 nanomaterials to respond in visible light and significantly improved their electron-hole separation efficiency.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Iron-modified biochar-based bilayer permeable reactive barrier for Cr(VI) removal

In this study, iron (Fe)-modified biochar (FeBC) has been developed to remove hexavalent chromium (Cr(VI)) from groundwater and is suitable for use in permeable reactive barriers (PRBs). However, Cr(VI) removal behavior and chemical processes in FeBC-based PRBs are not fully understood, and the potential for Fe release has not been addressed. In this study, three FeBC-based PRBs were assessed in column experiments for 563 days with respect to their ability to remove Cr(VI). Bilayer column filled with FeBC+limestone and BC+limestone in two separate layers (FeBC_Ca_BC) showed the best performance in terms of Cr(VI) removal with a low treatment cost. The corrosion of FeBC was mainly related to pH and Cr(VI) concentration rather than flow rate. Leached Fe was attenuated by BC and limestone and reutilized in FeBC_Ca_BC. Cr(VI) was reduced to Cr(III) and then adsorbed or precipitated on the biochars. Cr and Fe formed inner-sphere complexes and then transformed from double corner sharing to edge sharing. During the reaction, Cr penetrated from the surface to the interior of the biochars and became a more stable species. This study provides evidence of the effectiveness of a new combination of biochars for Cr(VI) removal and insights into the reaction mechanisms.

42 ENGINEERING↗
DOE OSTI2025

An innovative radial gradient material design using hot isostatic pressing for applications in extreme environments

Functionally graded materials (FGMs) are highly advanced continuous or discontinuous structures whose structural and material properties vary along a singular geometric dimension either in the axial or radial direction. Here, the radial gradient FGM design makes for an optimal structural design to incorporate a bi-metallic structure with a copper-based high entropy alloy (Cu-HEA) with good mechanical properties and high irradiation resistance, and Chromium (Cr) with great corrosion resistance. This study focuses on the experimental design of a metal powder loading mechanism to fabricate a bi-metallic radial gradient structure using Cu-HEA and 99.9 % pure Cr metal powders. The powder loading strategy uses custom-designed concentric cylindrical dividers to separate the individual compositions. Two benchtop trial runs were performed for design optimization. The optimized design was then implemented to eventually load the HEA and Cr powders for consolidation via powder metallurgy hot isostatic pressing (PM-HIP). The electron microscopy analysis reveals the successful fabrication of the radial gradient structure with the chemical mapping analysis, demonstrating the gradual composition shift from the HEA at the center to the pure-Cr at the periphery via a three-step gradient.

High Entropy Alloys (HEAs)↗
DOE OSTI2020

Microstructural banding of directed energy deposition-additively manufactured 316L stainless steel

The microstructures of 316 L stainless steel created by rapid solidification are investigated here by comparing the similar microstructures of individual hatches of directed energy deposition additive manufacturing (DED-AM) and those of single, laser surface-melted tracks formed on a solid plate. High recoil pressure, which is exponentially dependent on the laser beam power density, induces convection of the melt pool, which causes formation of microstructural bands in the as-solidified microstructure. The microstructural bands are associated with changes in the chromium concentration and are a significant component of the inhomogeneous microstructure of DED-AM.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion behavior of ferritic FeCrAl alloys in simulated BWR normal water chemistry

Ferritic iron-chromium-aluminum (FeCrAl) alloys with varying Cr content were subjected to in-situ irradiation-corrosion with energetic protons or electron beams in pure water with various oxygen concentrations. Oxide microstructure and composition were characterized to compare the corrosion under irradiation with the thermal corrosion in the same water conditions. The dominant effect seems to be the production of H 2 O 2 at the surface by the intense proton and electron beams. The corrosion potential of FeCrAl under BWR-NWC condition is somewhat above the Cr 2 O 3 /CrO 4 2- phase boundary, oxidizing the Cr(III) to Cr(VI) in the outer part of the film, but with some Cr(III) remaining in the interior of the oxide. The beam increases the corrosion potential, significantly reducing Cr(III) content throughout the oxide. Finally, the crystallites on the surface, which form by re-precipitation from solution, do not contain Cr because at low potential Cr(III) is not soluble, and at high potential Cr(VI) is quite soluble.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electron microscopy characterization of the fuel-cladding interaction in medium burnup annular fast reactor MOX

In this work, we present electron microscopy data focused on the fuel-cladding interaction layer in annular fast reactor MOX with HT-9 cladding at medium burnup. In agreement with previous literature data, the volatile fission products Cs, Te and I have migrated radially into the extreme fuel periphery and partially interacted with the cladding. The accumulation of Cs has occurred in the outermost rim of the fuel pellet, where grain recrystallization has also been observed. Significant amounts of Pd have been found in the interaction zone, particularly in the sample taken from the upper half of the fissile column where the cladding temperatures are higher. At this axial location, Cr has been enriched at the cladding inner surface and diffused into the fuel. Furthermore, chromium remains mainly in metallic form, but locally formed oxides. The fission products Cs, Te and I are found, with variable composition, in form of nanocrystalline regions dispersed in the metallic Cr-rich layer. The morphology and chemical characteristics of the layer suggest a non-oxidative corrosion mechanism as principal cladding degradation phenomenon occurring in this sample, with local onset of Cr oxidation within the nanocrystalline precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength and rupture geometry of un-irradiated C26M FeCrAl under LOCA burst testing conditions

Ferritic iron-chromium-aluminum (FeCrAl) alloys are an accident tolerant fuel candidate to replace the incumbent Zr-based claddings. Nuclear grade FeCrAl alloys are marked by superior high temperature mechanical behavior and exceptional steam oxidation resistance, both of which increase safety margins during accident scenarios. In the present study, the loss of coolant accident (LOCA) burst behaviors of three un-irradiated commercially fabricated cladding materials in a simulated LOCA environment were compared: (1) T35Y2, a 1 st generation nuclear grade FeCrAl, (2) C26M, a 2 nd generation nuclear grade FeCrAl, and (3) Zircaloy-2. Both FeCrAl alloys showed improved mechanical strength and steam oxidation resistance compared to Zircaloy-2. C26M claddings burst at significantly higher temperatures for all tested engineering hoop stresses, had limited ballooning, and demonstrated preferential fuel retention behavior in terms of burst opening area and length. High temperature tensile data for C26M is also presented. For both un-irradiated FeCrAl alloys, it was found that a distinct “threshold” burst stress signified the transition between small and large openings. Finally, higher threshold hoop stresses were associated with higher uniaxial strength for the FeCrAl alloys, indicating that tensile data, rather than creep data, could be useful for predicting rupture size and assessing fuel dispersal concerns.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of sample bias on adhesion of magnetron sputtered Cr coatings on SiC

Swelling of SiC at 300 C due to in-service neutron irradiation causes tensile residual stresses in coatings which are expected to adversely affect the performance of coated SiC composite fuel cladding for light water reactors. Matching the coating swelling with the substrate, a solution common for thermal expansion, is not practical in the case of neutron irradiation. Biasing samples during magnetron sputtering deposition induces compressive residual stress which may counteract this. In this study, chromium coatings were deposited on SiC by DC magnetron sputtering with no external heating at bias voltages of –50V, –75V, and –100V. The effects of the bias voltage on morphology, residual stress, microstrain, texture, and adhesion are shown. The low deposition temperature resulted in the coating microstructure evolution following an energetic particle bombardment dominated trend. Additionally, at the two lower bias voltages knock-on implantation dominated increasing the residual stress and microstrain while at the highest bias voltage, thermal spike migration allowed for defect relaxation. When the knock-on induced compressive residual stress exceeded 0.8 GPa microcrack formation in the SiC substrate decreased coating adhesion. While no microcracks formed at the lowest bias voltage, insufficient atomic mobility during coating growth lead to voids forming in the coating. A balance is needed to form void-free coatings that have high compressive residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Corrosion property of Alloy 625 in Molten FLiNaK salt according to the Tellurium Concentrations

For this work, the corrosion properties of Alloy 625 have been studied in molten FLiNaK salt for 48 h at 700 °C as a function of tellurium (Te) concentrations using immersion tests and electrochemical methods. Under specific Te concentrations, we found that Te-induced corrosion can be suppressed and help protect the alloy against corrosion. The sample after the immersion test containing 0.1 wt.% Te (0.1 wt.% Te sample) had the lowest corrosion depth and mass loss, coupled with the highest charge transfer resistance, obtained using electrochemical impedance spectroscopy (EIS). On the other hand, the alloy with Te content above 0.1 wt.% exhibited severe corrosion penetration and lower charge transfer resistance in FLiNaK. Based on thermodynamical and electrochemical analyses, a corrosion mechanism of Alloy 625 in the molten salt containing Te was theorized involving the formation of stable corrosion products such as Ni/Fe rich layer depleted in Cr, nickel telluride, and chromium oxide.

Hong, Minsung↗
DOE OSTI2026

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗
DOE OSTI2021

Holistic design principles for flow batteries: Cation dependent membrane resistance and active species solubility

Cation dependent resistance of a commercial cation exchange membrane, Nafion™ 212, as well as the solubility of select active materials are investigated, demonstrating practical consequences of cation choice on redox flow battery (RFB) performance. The conductivity of alkali and methyl- or -alcohol substituted ammonium cations through pretreated Nafion™ 212 reveal that cation size is the dominant factor affecting ionic transport. Among the alkali series the resistance increases with larger ionic radii and similarly, with increasing steric bulk through substitution on ammonia. The solubility of ferrocyanide, a commonly used redox flow battery posolyte (or catholyte), as well as iron, cobalt, and chromium metal-organic compounds are determined for the same series of cations. Full cells are assembled using various cation mixtures and membrane pre-treatments to demonstrate practical effects of each variable. Here, we highlight the need to carefully select the correct cations for efficient electrolyte design, since certain cations may lead to high conductivity but low solubility, or vice versa, and provide design principles for RFBs using Nafion™ 212.

25 ENERGY STORAGE↗
DOE OSTI2022

Optimization of metal-supported solid oxide fuel cells with a focus on mass transport

Performance of symmetric-architecture metal-supported solid oxide fuel cells was improved significantly by optimizing the catalyst infiltration process and metal support structure. Optimization of component structure and processing parameters was performed during tape-casting and fabrication of button cells. Mass transport of oxygen in the metal support was identified as a major limitation. To overcome this limitation, pore former loading and thickness of the metal support (130–250 μm) were optimized. The catalyst infiltration process was also improved by studying the impact of firing temperature (400 °C–900 °C) and infiltration cycle numbers (1–15). The maximum power density of the optimized cell was 0.9 W cm –2 at 700°C using hydrogen as a fuel, a three-fold increase over the baseline cell performance. The degradation rate of optimized cells at 550 °C, 600 °C, and 700 °C was 2%, 4.5%, and 5.5% per 100 h, respectively. Here, the phenomena of mass transport, catalyst coarsening, and chromium poisoning on the catalyst were analyzed by electrochemical impedance spectroscopy and scanning electron microscopy.

13 HYDRO ENERGY↗
DOE OSTI2025

Chemistry effects on ODS steel consolidated via laser powder bed fusion from GARS powder

Oxide Dispersion Strengthened (ODS) steels are promising candidate alloys for structural and cladding applications in extreme environments. They contain a high density of nanoscale oxides for high temperature mechanical strength and radiation resistance. In this work, gas atomization reaction synthesis (GARS) was used to produce powders that were used for additive manufacturing (AM) Laser Powder Bed Fusion consolidation of ODS steels, in order to skip the traditional mechanical alloying of blended yttria and alloy powders. Powder containing iron, chromium, and tungsten with varying amounts of yttrium, titanium, oxygen and zirconium were used to produce ODS steel samples. AM consolidated specimens and powder samples were characterized with transmission electron microscopy. TEM imaging, diffraction patterns, and energy dispersive X-ray spectroscopy (EDS) was used to identify phases present before and after consolidation across chemistries. The effect of the controlled oxygen input (from GARS) and the oxide-forming additions (Y, Ti, Zr) on precipitate size distribution and composition is substantiated and discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The role of Cr concentration and temperature on cavity swelling with co-injected helium in dual-ion irradiated Fe and Fe-Cr alloys

The level of chromium plays an essential role in irradiation tolerance of Fe-Cr ferritic alloys. However, conflicting results have been reported regarding the dependence of cavity swelling under irradiation on Cr level and temperature. Here, we have performed a comprehensive set of simultaneous dual-ion (Ni + He) irradiations to high dose (~30 displacements per atom, dpa) at 400–550 °C on a series of ultra-high purity Fe and Fe-Cr binary alloys (3–14 wt.%Cr). Helium co-implantation rates of 0.1 and 10 appm He/dpa were selected to examine He synergistic effects relevant for fission and fusion reactor conditions, respectively. Cavities were observed in all irradiated samples by transmission electron microscopy. The results show that higher He implantation rate causes a shift in the swelling peak to higher temperatures in both Fe and Fe-Cr alloys. When assuming smaller cavities as biased sinks, the non-monotonic nature of the cavity swelling behavior is related to the ratio of biased to unbiased point defect sink strengths. Cr-enriched precipitates were observed in Fe-14Cr irradiated at 400 °C by atom probe tomography. Our analysis suggests the formation of Cr-enriched precipitates could suppress cavity swelling for Fe-Cr alloys with Cr content above 10 wt%.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The effects of Fe and Al on the phase transformations and mechanical behavior of β-Ti alloy Ti-11at.%Cr

Alloy composition is important for developing desired microstructures in beta-titanium (β-Ti) alloys during thermomechanical processing. In this work, the relatively low-cost alloying elements iron (Fe) and aluminum (Al) were added to a base Ti-11at%chromium (Cr) alloy and in-situ and ex-situ examination of the microstructural evolution and mechanical properties during tension, hardness, elevated temperature X-ray diffraction (XRD) and resonance ultrasound spectroscopy (RUS) were performed. The 400 °C XRD revealed that Ti-11at%Cr underwent β-to-ω and β-to-α transformations. Adding 0.85at% Fe reduced the volume fraction of the ω- and α-phases, and adding 5.3at% Al inhibited the β-to-ω transformation. The 400 °C RUS showed that the alloys containing the ω phase exhibited an increase in shear modulus (G) of ~140%, while the ω-free alloys exhibited an increase of only ~102%. The hardness and strength values of the ω-containing Ti-11Cr and Ti-11Cr-0.85Fe increased with increased ω-phase volume fraction when the ω/α ratio was greater than 0.25. The relationship between ω/α volume ratios and mechanical properties is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Irradiation-induced formation of G-phase precipitates and M 2 X carbides in self-ion irradiated HT-9

Ferritic-martensitic steels with high chromium content are a promising material group for advanced nuclear systems due to their high temperature strength and good irradiation tolerance. HT-9 is an optimized and often-studied alloy in this group, but additional studies are required on its radiation response under extreme conditions to be experienced in various types of nuclear reactors, especially with respect to phase stability under irradiation. Self-ion irradiation of HT-9 by 5 MeV Fe ions was used to simulate neutron-induced behavior reaching peak doses of 100 and 300 dpa at temperatures ranging from 450 to 550 °C. M 23 C 6 carbides that existed prior to irradiation were found to remain stable under all examined irradiation conditions. As irradiation progressed at 450 and 500 °C, however, formation of spherical-like G-phase precipitates and needle-like M 2 X carbides was observed. G-phase precipitates were found to be enriched in Ni, Si, and Mn, and show no interface segregation, whereas needle-like M 2 X carbides were rich in Cr and Mo and clearly displayed interface segregation of Ni and Si. M 2 X carbide formation is believed to be assisted by vacancies, while G-phase precipitation is thought to be assisted by interstitials. Finally, this difference in defect-mediated formation leads to a difference in distribution with depth. M 2 X carbides are distributed over shallower depths than that of G-phase precipitates, consistent with defect imbalance predictions that consider the influence of the injected interstitial effect.

atom probe tomography↗