Search NASA⌕ Search

SEARCH · Search NASA

Results for “computer code development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

The dynamic flexural response of propeller blades

The determination of the torsional constants of three blade models having NACA four-digit symmetrical airfoil cross sections is presented. Values were obtained for these models analytically and experimentally. Results were also obtained for three other models having rectangular, elliptical, and parabolic cross sections. Complete modal analyses were performed for five blade models. The identification of modal parameters was done for cases when the blades were modeled as either undamped or damped multi-degree-of-freedom systems. For the experimental phase of this study, the modal testing was performed using a Dual Channel FFT analyzer and an impact hammer (which produced an impulsive excitation). The natural frequency and damping of each mode in the frequency range up to 2 kHz were measured. A small computer code was developed to calculate the dynamic response of the blade models for comparison with the experimental results. A comparison of the undamped and damped cases was made for all five blade models at the instant of maximum excitation force. The program was capable of handling models where the excitation forces were distributed arbitrarily along the length of the blade.

Djordjevic, S. Z.↗

Importance of inlet boundary conditions for numerical simulation of combustor flows

Fluid dynamic computer codes for the mathematical simulation of problems in gas turbine engine combustion systems are required as design and diagnostic tools. To eventually achieve a performance standard with these codes of more than qualitative accuracy it is desirable to use benchmark experiments for validation studies. Typical of the fluid dynamic computer codes being developed for combustor simulations is the TEACH (Teaching Elliptic Axisymmetric Characteristics Heuristically) solution procedure. It is difficult to find suitable experiments which satisfy the present definition of benchmark quality. For the majority of the available experiments there is a lack of information concerning the boundary conditions. A standard TEACH-type numerical technique is applied to a number of test-case experiments. It is found that numerical simulations of gas turbine combustor-relevant flows can be sensitive to the plane at which the calculations start and the spatial distributions of inlet quantities for swirling flows.

Sturgess, G. J.↗

PREWATE: An interactive preprocessing computer code to the Weight Analysis of Turbine Engines (WATE) computer code

The Weight Analysis of Turbine Engines (WATE) computer code was developed by Boeing under contract to NASA Lewis. It was designed to function as an adjunct to the Navy/NASA Engine Program (NNEP). NNEP calculates the design and off-design thrust and sfc performance of User defined engine cycles. The thermodynamic parameters throughout the engine as generated by NNEP are then combined with input parameters defining the component characteristics in WATE to calculate the bare engine weight of this User defined engine. Preprocessor programs for NNEP were previously developed to simplify the task of creating input datasets. This report describes a similar preprocessor for the WATE code.

Fishbach, L. H.↗

Finite-difference fluid dynamics computer mathematical models for the design and interpretation of experiments for space flight

Numerical methods are used to design a spherical baroclinic flow model experiment of the large scale atmosphere flow for Spacelab. The dielectric simulation of radial gravity is only dominant in a low gravity environment. Computer codes are developed to study the processes at work in crystal growing systems which are also candidates for space flight. Crystalline materials rarely achieve their potential properties because of imperfections and component concentration variations. Thermosolutal convection in the liquid melt can be the cause of these imperfections. Such convection is suppressed in a low gravity environment. Two and three dimensional finite difference codes are being used for this work. Nonuniform meshes and implicit iterative methods are used. The iterative method for steady solutions is based on time stepping but has the options of different time steps for velocity and temperature and of a time step varying smoothly with position according to specified powers of the mesh spacings. This allows for more rapid convergence. The code being developed for the crystal growth studies allows for growth of the crystal as the solid-liquid interface. The moving interface is followed using finite differences; shape variations are permitted. For convenience in applying finite differences in the solid and liquid, a time dependent coordinate transformation is used to make this interface a coordinate surface.

Roberts, G. O.↗

Nacelle Aerodynamic and Inertial Loads (NAIL) project

A flight test survey of pressures measured on wing, pylon, and nacelle surfaces and of the operating loads on Boeing 747/Pratt & Whitney JT9D-7A nacelles was made to provide information on airflow patterns surrounding the propulsion system installations and to clarify processes responsible for inservice deterioration of fuel economy. Airloads at takeoff rotation were found to be larger than at any other normal service condition because of the combined effects of high angle of attack and high engine airflow. Inertial loads were smaller than previous estimates indicated. A procedure is given for estimating inlet airloads at low speeds and high angles of attack for any underwing high bypass ratio turbofan installation approximately resembling the one tested. Flight procedure modifications are suggested that may result in better fuel economy retention in service. Pressures were recorded on the core cowls and pylons of both engine installations and on adjacent wing surfaces for use in development of computer codes for analysis of installed propulsion system aerodynamic drag interference effects.

Source record↗

Nacelle Aerodynamic and Inertial Loads (NAIL) project

Inlet airloads were measured by integration of pressures recorded at 252 locations on the right hand inboard (JT9D-7A) nacelle of the Boeing 747 aircraft. Pressures were recorded at 45 locations on the right hand outboard nacelle for comparison. Inertial loads were measured on both nacelles using accelerometers and rate gyros. Flight conditions included takeoffs at several gross weights, high g turns, and a simulated acceptance flight. Airloads at takeoff rotation were found to be larger than at any other normal service condition because of the combined effects of high angle of attack and high engine airflow. Inertial loads were smaller than previous estimates had indicated. A procedure is given for estimating inlet airloads at low speeds and high angles of attack for any underwing high bypass ratio turbofan installation approximately resembling the one tested. Flight procedure modifications are suggested that may result in better fuel economy retention in service. Pressures were recorded on the core cowls and pylons of both engine installations and on adjacent wing surfaces for use in development of computer codes for analysis of installed propulsion system aerodynamic drag interference effects.

Source record↗

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary-layer characteristics at Reynolds numbers exceeding one billion is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility. The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentationn techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, W. S.↗

Improved design of subcritical and supercritical cascades using complex characteristics and boundary-layer correction

The method of complex characteristics and hodograph transformation for the design of shockless airfoils was extended to design supercritical cascades with high solidities and large inlet angles. This capability was achieved by introducing a conformal mapping of the hodograph domain onto an ellipse and expanding the solution in terms of Tchebycheff polynomials. A computer code was developed based on this idea. A number of airfoils designed with the code are presented. Various supercritical and subcritical compressor, turbine and propeller sections are shown. The lag-entrainment method for the calculation of a turbulent boundary layer was incorporated to the inviscid design code. The results of this calculation are shown for the airfoils described. The elliptic conformal transformation developed to map the hodograph domain onto an ellipse can be used to generate a conformal grid in the physical domain of a cascade of airfoils with open trailing edges with a single transformation. A grid generated with this transformation is shown for the Korn airfoil. Previously announced in STAR as N83-24474

Sanz, J. M.↗

Predicting the Performance of an Axial-Flow Compressor

Stage-stacking computer code (STGSTK) developed for predicting off-design performance of multi-stage axial-flow compressors. Code uses meanline stagestacking method. Stage and cumulative compressor performance calculated from representative meanline velocity diagrams located at rotor inlet and outlet meanline radii. Numerous options available within code. Code developed so user modify correlations to suit their needs.

Steinke, R. J.↗

Axial-Flow Compressor Performance With Water Ingestion

Stage-stacking computer code (WISGSK) developed for prediction of offdesign axial-flow compressor performance with water ingestion. Code uses meantime stage-stacking method; stage and cumulative compressor performance calculated utilizing representative triangles located at rotor inlet and outlet mean radii. Code provides options for calculation of performance with mixtures of gases such as air and water vapor and air/water droplet mixtures with different water contents. Useful for obtaining preliminary estimates of overall performance of compressors with water ingestion given design point details corresponding to airflow and nature of corrections for air/water mixture flow.

Tsuchiya, T.↗

Laser Schlieren and ultraviolet diagnostics of rocket combustion

A low pressure oxygen/hydrogen turbine drive combustor hot-fire test series was conducted on the Turbine Drive Combustor Technology Program. The first objective was to gather data on an axisymmetric combustion system to support anchoring of a new combustion/fluid dynamics computer code under development on the same contract. The second objective was to gain insight into low mixture ratio combustion characteristics of coaxial injector elements.

Fisher, S. C.↗

Photovoltaic conversion of laser power to electrical power

Photovoltaic laser to electric converters are attractive for use with a space-based laser power station. This paper presents the results of modeling studies for a silicon vertical junction converter used with a Nd laser. A computer code was developed for the model and this code was used to conduct a parametric study for a Si vertical junction converter consisting of one p-n junction irradiated with a Nd laser. These calculations predict an efficiency over 50 percent for an optimized converter.

Walker, G. H.↗

Modeling the filament winding process

A model is presented which can be used to determine the appropriate values of the process variables for filament winding a cylinder. The model provides the cylinder temperature, viscosity, degree of cure, fiber position and fiber tension as functions of position and time during the filament winding and subsequent cure, and the residual stresses and strains within the cylinder during and after the cure. A computer code was developed to obtain quantitative results. Sample results are given which illustrate the information that can be generated with this code.

Calius, E. P.↗

ICAN: Integrated Composites Analyzer

Program calculates macromechanical, micromechanical, and related environmental effects. Computer code ICAN developed to carry out comprehensive linear analyses of multilayered fiber composites. Contains essential features required to design structural components made from fiber composites. Code in FORTRAN IV.

Chamis, Christos C.↗

Investigation of the external flow analysis for density measurements at high altitude

The results of analysis performed on the external flow around the shuttle orbiter nose regions at the Shuttle Upper Atmosphere Mass Spectrometer (SUMS) inlet orifice are presented. The purpose of the analysis is to quantitatively characterize the flow conditions to facilitate SUMS flight data reduction and subsequent determination of orbiter aerodynamic force coefficients in the hypersonic rarefied flow regime. Experimental determination of aerodynamic force coefficients requires accurate simultaneous measurement of forces (or acceleration) and dynamic pressure along with independent knowledge of density and velocity. The SUMS provides independent measurement of dynamic pressure; however, it does so indirectly and requires knowledge of the relationship between measured orifice conditions and the dynamic pressure which can only be determined on the basis of molecule or theory for a winged configuration. Monte Carlo direct simulation computer codes were developed for both the flow field solution at the orifice and for the internal orifice flow. These codes were used to study issues associated with geometric modeling of the orbiter nose geometry and the modeling of intermolecular collisions including rotational energy exchange and a preliminary analysis of vibrational excitation and dissociation effects. Data obtained from preliminary simulation runs are presented.

Bienkowski, G. K.↗

Photovoltaic conversion of laser power to electrical power

Photovoltaic laser to electric converters are attractive for use with a space-based laser power station. The results of modeling studies for a silicon vertical junction converter used with a Nd laser are given. A computer code was developed for the model and this code was used to conduct a parametric study for a Si vertical junction converter consisting of one p-n junction irradiated with a Nd laser. These calculations predict an efficiency over 50 percent for an optimized converter.

Walker, Gilbert H.↗

Use of a corrugated surface to enhance radiation tolerance in a GaAs solar cell

The use of a corrugated surface on a GaAs solar cell and its effects on radiation resistance were studied. A compute code was developed to determine the performance of the cell for various geometric parameters. The large optical absorption coefficient of GaAs allows grooves to be only 4-5 micrometers deep. Using accepted material parameters for GaAs solar cells the theoretical performances were compared for various corrugated cells before and after minority carrier diffusion length degradation. The total power output was maximized for both n(+)/p and p(+)/n cells. Optimum values of 1.0-1.5 and 5.0 micrometers for groove and ridge widths respectively were determined.

Leon, Rosa P.↗

Particle trajectory computer program for icing analysis of axisymmetric bodies - A progress report

Aircraft exposed to an atmospheric icing environment can accumulate ice, resulting in a sharp increase in drag, a reduction in lift, control surface fouling, and engine damage all of which result in a hazardous flight situation. NASA Lewis Research Center (LeRC) has conducted a program to examine, with the aid of high-speed computer codes, how the trajectories of particles contribute to the ice accumulation on airfoils and engine inlets. For this effort, a computer code was developed to calculate icing particle trajectories and impingement limits for axisymmetric inlets. The original research-oriented NASA code was upgraded and modified to meet the requirements of the design engineer. The improved code is capable of performing trajectory calculations for any atmospheric conditions and droplet sizes. It can handle single droplets or a distribution of various droplet sizes. The four programs that comprise the code are described and the results of a test case using flight conditions for a Fokker F100 icing tunnel test are presented.

Maltezos, Dimitrios G.↗